CO2化学吸收剂

化学吸收法是燃后CO₂捕集的主要方法之一,本文介绍了化学吸收法脱除CO₂的系统工艺及特点,综述了CO₂吸收剂的研究现状,介绍了典型吸收剂:氨水吸收剂、氨基酸盐吸收剂、碳酸钾吸收剂的研究进展,以及新型吸收剂研究方向:混合胺吸收剂、相变吸收剂、离子液体吸收剂、纳米流体吸收剂,CO₂开关型吸收剂和新型有机胺吸收剂,并分析比较了各种吸收剂的优缺点。分析表明混合胺和相变吸收剂节能潜力较大,较其他四种新型吸收剂更为成熟,因此具有一定的工业化潜力。     

Li4SiO4对CO2捕集性能的实验研究

以Li₂CO₃和SiO₂为原料,通过高温固相合成法合成了CO₂捕集剂Li₄SiO₄,并用X射线粉末衍射仪(XRD)、扫描电子显微镜(SEM)对所合成的材料在CO₂捕集前后的晶相变化以及微观结构进行了表征。通过热重分析仪(TGA)研究了Li₄SiO₄材料吸附CO₂的性能,并在小型热态实验台架上进行了CO₂热态捕集实验。实验结果表明,Li₄SiO₄对CO₂的捕集性能受Li₄SiO₄合成温度、CO₂的吸附温度以及气体中CO₂含量的影响,在700 ℃下制得的Li₄SiO₄具有最佳的CO₂吸附特性,最大吸附增量可达34%。Li₄SiO₄的吸附能力随着CO₂含量和吸附时间的增加而增加,当CO₂浓度分别为75%、67%、60%时,700 ℃ Li₄SiO₄对CO₂最大吸附量分别可达6.68 mmol/g、3.37 mmol/g、2.02 mmol/g (理论量8.33 mmol/g)。     

膜接触器 复合有机胺溶液捕集CO2(英文）

本文提出一种基于氨基酸盐的CO₂复合吸收剂,采用膜接触器 复合溶液耦合技术研究了吸收CO₂的性能,并与单一氨基酸盐溶液吸收性能进行了比较,讨论了气液流速等因素对气液出口CO₂浓度、捕集效率和总传质系数的影响,开发了一个阻力层模型预测膜接触器的总传质系数。结果表明：复合溶液的性能明显好于单一氨基酸盐溶液;与单一溶液比较,使用复合溶液,气相出口CO₂浓度较低,液相出口CO₂浓度较高,捕集效率也较高;复合溶液的总传质系数明显高于单一溶液。可以证实,在膜吸收过程中氨基酸盐基复合溶液是一高效的CO₂吸收剂。模型的预测值符合实验值。     

无机盐活化剂-氨基酸盐基溶液捕集温室气体CO2

将无机盐K₃PO₄、K₂HPO₄和KH₂PO₄作为活化剂,分别添加于氨基乙酸盐溶液中,形成CO₂活化吸收剂,采用膜接触器 再生循环装置,评价和比较了氨基乙酸盐和活化吸收剂捕集CO₂的性能,研究了活化剂的浓度、气液流速等因素对总体积传质系数、传质通量和捕集率的影响。结果表明,磷酸盐活化剂在氨基乙酸盐吸收剂中,对CO₂的捕集均产生影响,活化效应存在PO₄^3－＞HPO₄^2－＞H₂PO₄^－的规律;添加少量活化剂的作用比添加较多量的活化作用大;活化吸收剂的捕集率明显大于非活化吸收剂;膜吸收流体力学状态的改变,能够改善膜接触器传质性能,增大传质通量,但增大的程度有限。     

凹凸棒黏土对燃煤PM2.5排放及团聚捕集特性影响

在固定床反应系统上考察凹凸棒黏土对燃煤可吸入颗粒物PM_2.5的排放及团聚捕集特性影响,分析凹凸棒黏土添加量以及添加凹凸棒黏土情况下燃烧气氛、燃烧温度和钙硫物质的量比等参数对燃煤PM_2.5的数量浓度、质量浓度以及团聚捕集率的影响规律。结果表明,煤燃烧过程中添加凹凸棒黏土可以显著降低PM_2.5排放浓度,凹凸棒黏土的添加量不宜超过3%(质量分数);空气气氛下燃烧产生的PM_2.5多于O₂/CO₂气氛;随着钙硫物质的量比的增大,PM₁的质量浓度减小,但PM_1~2.5的质量浓度增大,颗粒物的粒径有向更大粒径转移的趋势;燃烧温度的升高会促进PM_2.5各粒径范围颗粒物的生成,降低了凹凸棒黏土对PM_2.5团聚捕集率。     

CO2高效资源化利用的高温熔盐电化学技术研究

高温熔融盐具有CO₂吸收容量大、电化学窗口宽、高温下反应动力学快等特点,是利用清洁电能大规模捕集和资源化利用CO₂颇具实用化潜力的电解液体系. 本文主要介绍作者课题组近十年关于高温熔盐CO₂捕集与电化学资源化转化(MSCC-ET)技术的相关研究工作,包括熔融盐电解质对CO₂的吸收、阴极过程动力学、电解条件对产物的影响、析氧阳极、电解过程能量效率和CO₂捕获潜力,并展望了MSCC-ET技术的发展前景.     

液相共存成分对氨法脱碳吸收液解吸CO2的影响研究

考察了烟气中SO₂、NO_x和CO₂与氨水的反应机理,研究了模拟解吸液解吸过程中主要液相共存成分,如(NH₄)₂SO₃、(NH₄)₂SO₄、NH₄NO₃、NaCl、NH₄Cl和(NH₄)₂CO₃对CO₂解吸的影响.研究表明,不同液相共存成分、质量分数、pH值、表面张力等对CO₂解吸产生一定影响,大部分液相共存成分的存在,会降低脱碳溶液CO₂的解吸量.质量分数低于10％的液相共存组分对脱碳吸收液CO₂解吸过程的制约作用依次为(NH₄)₂SO₃>NH₄NO₃>(NH₄)₂SO₄>NaCl>(NH₄)₂CO₃.因此,在碳捕集前应对烟气中的杂质成分进行脱除,减少其对解吸液理化特性的影响.     

CaO/MgO和CaO/Ca9Al6O18同时捕集CO2/SO2的循环吸收特性

以葡萄糖酸钙与葡萄糖酸镁及L-乳酸铝为前驱物,湿法制得了四种CaO/MgO和CaO/Ca₉Al₆O₁₈吸收剂,并进行了同时捕集CO₂/SO₂的实验。考察了吸收剂种类、质量配比、SO₂浓度及煅烧温度等对吸收剂吸收性能的影响。结果表明,CaO/MgO(质量比为75%/25%)吸收剂和CaO/Ca₉Al₆O₁₈(质量比为75%/25%)吸收剂分别保持了最好的吸收CO₂能力和最好的循环稳定性。SO₂严重阻碍了吸收剂对CO₂的捕集。SO₂浓度越高,吸收剂吸收CO₂能力下降的越快,但同时吸收SO₂的转化率也越高。数次循环后,总的Ca利用率开始上升,且SO₂浓度越高,上升趋势越明显。煅烧温度对CaO/MgO吸收剂和CaO/Ca₉Al₆O₁₈吸收剂循环吸收特性的影响略有不同。     

离子液体捕集CO2

CO₂是导致温室效应的最主要成分,因此碳捕集技术的研究受到学术界和产业界的高度重视。离子液体具有不挥发、不燃烧、热稳定性好、溶解能力强、结构和性质可调节并可循环使用等特性,在CO₂的吸收/分离领域展现了广阔的应用前景。本文系统地综述了近年来常规离子液体、功能化离子液体、支撑离子液体膜、聚合离子液体以及离子液体与分子溶剂的混合物在捕集CO₂方面的研究进展;讨论了离子液体的阳离子结构、阴离子类型、烷基链长度、阴/阳离子的氟化程度和功能化、离子液体的负载作用和聚合效应以及体系的温度和压力对CO₂选择性捕集性能的影响;分析了可能的捕集机理以及各种捕集方法的优点和缺点;提出了目前需要进一步研究的若干重要问题,并对其发展前景进行了展望。     

臭氧氧化结合湿法喷淋对玻璃窑炉烟气同时脱硫脱硝实验研究

采用臭氧氧化结合湿法喷淋对模拟玻璃窑炉烟气开展了同时脱硫脱硝实验研究.采用不同溶液(NaOH、Na₂S)进行了喷淋实验.结果表明,保证溶液pH值在10以上,NaOH浓度对NO_x脱除效率无影响,SO₂的存在促进了NO_x吸收.当O₃/NO物质的量比为1.6、溶液NaOH浓度为0.5%时,NO_x脱除效率可达70%,SO₂脱除效率在99%以上.往喷淋液中添加Na₂S,NO_x脱除效率随Na₂S浓度增加而提高,SO₂的存在对NO_x脱除效率无影响.当O₃/NO物质的量比为1.2、溶液中NaOH浓度为0.5%、添加剂Na₂S浓度为0.6%时,NO_x脱除效率可达70%,SO₂脱除效率在95%以上.60 min长时间运行实验证明,模拟烟气中的NO_x经碱液和添加剂吸收后主要以NO^-₂的形式存在于喷淋液中,且NO_x脱除效率不随溶液pH值的变化而变化.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.