Microwave-assisted Polymerization of ε-Caprolactone with Maleic Acid as Initiator and Drug Release Behavior of Ibuprofen-Poly(ε-caprolactone) System

Poly( ε-caprolactone)(PCL) with weight-average molar mass over 10000g/mol was synthesized by microwave-assisted ring -opening polymerization of ε-caprolactone(ε-CL) with maleic acid(MA) as initiator (2.45GHz,360W,85min),Ibuprofen-PCL controlled release system was prepared directly by the ROP of ε-CL in its mixture with ibuprofen.The release of ibuprofen from the system was sustained and steady.     

CONTROL OF DIMENSIONAL STABILITY AND DEGRADATION RATE IN ELECTROSPUN COMPOSITE SCAFFOLDS COMPOSED OF POLY(D,L-LACTIDE-co-GLYCOLIDE) AND POLY(ε-CAPROLACTONE)

The purpose of this study is to investigate the effect of composition poly(D,L-lactide-co-glycolide)/poly(ε- caprolactone)(PLGA/PCL)blending on the morphology,shrinkage and degradation behaviors of the electrospun fibers. With the increase of PLGA content in the composite fibers,the average diameter of the electrospun fibers increased from 1.35μm to 1.95μm.The serious shrinking of the electrospun PLGA meshes could be circumvented by adding 20% PCL in the fibers,resulting from the semi-crystalline nature ...     

ELECTROSPRAYING/ELECTROSPINNING OF POLY(γ-STEARYL-L-GLUTAMATE): FORMATION OF SURFACES WITH SUPERHYDROPHOBICITY

  Electrospraying/electrospinning of poly(γ-stearyl-L-glutamate) (PSLG) was investigated on a series solutions with different concentrations in chloroform. Field emission scanning electron microscopy (FESEM) and attenuated total reflectance Fourier transform infrared spectroscopy (FT-IR/ATR) were used to characterize the morphology and structure of the electrosprayed/electrospun polypeptide mats. It was found that electrospraying of PSLG with concentrations lower than 16 wt% afforded beads, while microfibers could be electrospun at the concentration of 22 wt%. The hydrophobicity of the electrosprayed/electrospun PSLG mats was investigated with static water contact angle (WCA) and tilt angle measurements. It was demonstrated that the superhydrophobic surfaces of PSLG with WCAs and tilt angles in the ranges of 150°-170° and 16.5°-4.2°, respectively, were obtained through electrospraying/electrospinning process.     

Fabrication of Novel Scaffolds Containing Collagen-I/Polylactic Acid/Nanohydroxyapatite via Co-electrospinning Methods

<正>A novel scaffold containing collagen-Ⅰ/polylactic acid(PLA)/nanohydroxyapatite(nHA) was prepared via co-electrospinning method.Different target substrates were used to improve the collection efficiency of this scaffold. The properties of the novel scaffold were compared with those of conventionally prepared ones.Compared to conventional method,the modified method was more efficient in producing the scaffold.Moreover,the porosity,thickness, and morphology of the novel scaffold were better than those of scaffolds prepared by conventional methods. The properties of collagen-Ⅰ,collagen-Ⅰ/PLA and collagen-Ⅰ/PLA/nHA scaffolds were also compared.Diameters of the electrospun fibers ranged from 180 to 405 nm,and roughness was present on the surface of the fibers due to the deposition of crystals of nHA along the long axis of the fibers.The fibers of the collagen-Ⅰ/PLA/nHA scaffold and the fibers of natural bone tissue had similar structure.     

Electrospinning of nylon-6,6 solutions into nanofibers: Rheology and morphology relationships

The relationship between the rheological properties of nylon-6,6 solutions and the morphology of their electrospun nanofibers was established. The viscosity of nylon-6,6 in formic acid(90%) was measured in the concentration range of 5 wt%-25 wt% using a programmable viscometer. Electrospinning of nylon-6,6 solutions was carried out under controlled parameters. The chemical structure, morphology and thermal properties of the obtained nanofibers were investigated using Fourier transform infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and differential scanning calorimetry(DSC), respectively. Entanglement concentration(ce) was found to be 15 wt% and a power law relationship between specific viscosity and solution concentration was observed with exponents of 2.0 and 3.3 for semi-dilute unentangled(c ce) and semi-dilute entangled(c ce) regimes, respectively. The diameter and uniformity of the nanofibers were found to be dependent on the viscosity. Moreover, the average diameter of electrospun nanofibers was found to be dependent on zero shear rate viscosity and normalized concentration(c/ce) in a power law relationship with exponents of 0.298 and 0.816, respectively. For nylon-6,6 solutions, the entanglement concentration(ce = 15 wt%) provides the threshold viscosity required for the formation of a stable polymeric jet during electrospinning and producing uniform beadless fibers. For concentrations less than ce, beaded fibers with some irregularities are formed. DSC analysis showed an increase in crystallinity of all electrospun samples compared to original polymer. Furthermore, Based on FTIR spectroscopy, α phase is dominant in electrospun nanofibers and minor amount of β and γ phases is also available.     

Bio-based and Biodegradable Electrospun Fibers Composed of Poly(L-lactide) and Polyamide 4

Novel bio-based and biodegradable block copolymers were synthesized by "click" reaction between poly(L-lactide)(PLLA) and polyamide 4(PA4). Upon tuning the molar mass of PLLA block, the properties of copolymers and electrospun ultrafine fibers were investigated and compared with those of PLLA and PA4 blends. PLLA and PA4 were found incompatible and formed individual crystalline regions, along with reciprocal inhibition in crystallization. Electrospun fibers were highly hydrophobic, even if hydrophilic PA4 was the rich component. The crystallinity of either PLLA or PA4 decreased after electrospinning and PLLA-rich as-spun fibers were almost amorphous. Immersion tests proved that fibers of block copolymers were relatively homogeneous with micro-phase separation between PLLA and PA4. The fibrous structures of copolymers were different from those of the fibers electrospun from blends, for which sheath-core structure induced by macro-phase separation between homopolymers of PLLA and PA4 was confirmed by TEM, EDS, and XPS.     

INVESTIGATION OF POLYDL-LACTIDE-b-POLY（ETHYLENE GLYCOL）-b-POLYDL-LACTIDE MICROSPHERES CONTAINING PLASMID DNA

PolyDL-lactide (PDLLA) and the block copolymer, polyDL-lactide-b-poly(ethylene glycol)-b-polyDL-lactide (PELA) were used as the microsphere matrix to encapsulate plasmid DNA. The PDLLA, PELA, pBR322-1oaded PDLLA and pBR322-1oaded PELA microspheres were prepared by solvent extraction method based on the formation of multiple w1/o/w2 emulsion. The microspheres were characterized by surface morphology, mean particle size, particle size distribution and loading efficiency. The integrity of DNA molecules after being extracted from microspheres was determined by agarose gel electrophoresis. The result suggested that plasmid DNA molecules could retain their integrity after being encapsulated by PELA. The PELA microspheres could prevent plasmid DNA from being digested by DNase. The in vitro degradation and release profiles of plasmid DNA-loaded microspheres were measured in pH - 7.4 buffer solution at 37℃. The in vitro degradation profiles of the microspheres were evaluated by the deterioration in microspheres surface morphology, the molecular weight reduction of polymer, the mass loss of microspheres, the changes of pH values of degradation medium, and the changes of particle size. The in vitro release profiles of the microspheres were assessed by measurement of the amount of DNA presented in the release medium at determined intervals. The release profiles were correlation with the degradation profiles. The release of plasmid DNA from PELA microspheres showed a similar biphasic trend, that is, an initial burst release was followed by a slow, but sustained release.     

EFFECT OF GAS FLOW RATE ON CRYSTAL STRUCTURES OF ELECTROSPUN AND GAS-JET/ELECTROSPUN POLY(VINYLIDENE FLUORIDE) FIBERS

The effect of gas flow rate on crystal structures of electrospun and gas-jet/electrospun poly(vinylidene fluoride) (PVDF) fibers was investigated.PVDF fibers were prepared by electrospinning and gas-jet/electrospinning of its N,N-dimethylformamide (DMF) solutions.The morphology of the PVDF fibers was investigated by scanning electron microscopy (SEM).With an increase of the gas flow rate,the average diameters of PVDF fibers were decreased.The crystal structures and thermal properties of the PVDF fibers w...     

Photo cross-linked biodegradable hydrogels for enhanced vancomycin loading and sustained release

A series of biodegradable hydrogels based on dextran and poly（L-glutamic acid） were fabricated for effective vancomycin loading and release. The preparation of hydrogels was simply achieved by photo cross-linking of methacrylated dextran and poly（L-glutamic acid）-g-hydroxyethyl methacrylate （PGH） in the presence of photoinitiator 12959. The structures of hydrogels were characterized by FTIR and SEM. The swelling and enzymatic degradation behaviors of hydrogels were examined to be dependent on the poly（L-glutamic acid） content in the hydrogels. The higher content of poly（L-glutamic acid） in the gel, the higher swelling ratio and quicker degradation were observed. More interestingly, the hydrogel with higher PGH ratio showed higher vancomycin （VCM） loading content, which might be due to the electrostatic interaction between carboxylate groups in hydrogel and ammonium group of VCM. In vitro drug release from the VCM-loaded hydrogels in aqueous solution exhibited sustained release of VCM up to 72 h, while the in vitro antibacterial test based on the VCM-loaded hydrogel showed an efficient Methicillin-Resistant S. aureus （MRSA） inhibition extending out to 7 days. These results demonstrated that the biodegradable hydrogels which formed by in situ photo-cross linking would be promising as scaffolds or coatings for local antibacterial drug release in tissue engineering.     

Preparation and characterization of electrospun fibers based on poly(L-lactic acid)/cellulose acetate

PLLA/CA mixtures of different compositions were successfully electrospun to obtain composite nanofibrous membranes.The microstructures of the membrances changed from homogeneous to heterogeneous with the addition of CA, which was observed by FE-ESEM.The PLLA/CA fabric membranes were characterized by mechanical testing,DSC and contact angle measurements.The tensile stress of the composite fibrous membranes increased obviously with the increase of CA content.DSC results indicated that the CA component was the main factor for the changes of enthalpies in the composite fibers.Contact angle measurements showed the hydrophilicity of the electrospun nanofiber membranes was improved with the addition of CA.     

Greatly enhanced hydrolytic degradation ability of poly(L-lactide) achieved by adding poly(ethylene glycol)

Plasticized poly(L-lactide)(PLLA) materials have been applied in many fields and the microstructure performance of such materials attracts much attention of researchers. However, few reports declared the hydrolytic degradation ability of the plasticized PLLA materials. In this article, a small quantity of poly(ethylene glycol)(PEG) was introduced into PLLA, which aimed to understand the hydrolytic degradation behavior of the plasticized PLLA materials. The microstructures of the plasticized samples were comparatively investigated using scanning electron microscopy(SEM), wide angle X-ray diffraction(WAXD), differential scanning calorimetry(DSC) and Flourier transform infrared spectroscopy(FTIR), etc. The results demonstrated that PEG improved the hydrophilicity of sample surface, and the relatively high content of PEG enhanced the crystallization ability of PLLA matrix. The hydrolytic degradation measurement was carried out at 60 ℃ in an alkaline solution of pH = 12. The results demonstrated that the plasticized PLLA samples exhibited accelerated hydrolytic degradation compared with the pure PLLA sample, and the hydrolytic degradation was also dependent on the PEG content. Further results demonstrated that PEG induced the change of hydrolytic degradation mechanism possibly due to the good dissolution ability of PEG in water, which provided more paths for the penetration of water. Furthermore, the microstructure evolution of the plasticized PLLA during the hydrolytic degradation process was also investigated, and the results demonstrated the occurrence of PLLA crystallization, which was possibly contributed to the decreased hydrolytic degradation rate observed at relatively long hydrolytic degradation time. This work is of great significance and may open a new way for promoting the reclamation of PLLA waste material.     

Electrospinning of GeO_2–C fibers and electrochemical application in lithium-ion batteries

GeO_2–C fibers were successfully synthesized using electrospinning homogeneous sol and subsequent calcination in an inert atmosphere. The spinnable sol was prepared by adding polyacrylonitrile(PAN)and polyvinylpyrrolidone(PVP) in a weight ratio of 1:1 into a mixture with white precipitate produced by dropping GeCl_4 into DMF. X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS),thermogravimetric analysis(TGA), scanning electron microscopy(SEM) and transmission electron microscopy(TEM) were employed to characterize the as-obtained fibers, and electrochemical tests were conducted to measure electrochemical performance of the electrode. The electrospun fibers have uniform diameters of 300 nm. After being calcined at 600 8C for 2 h in Ar, they transform to amorphous GeO_2–C fibers with the same morphologies. The Ge O_2–C fibers exhibit excellent cycling stability with a high reversible capacity of 838.93 m A h g~(-1)after 100 cycles at a current density of 50 m A g~(-1), indicating the composite fibers could be promising anode candidates for lithium-ion batteries.     

HypoGel负载Pd纳米催化剂制备与表征及温和条件下催化Suzuki反应(英文)

A new heterogeneous catalyst composed of Pd nanoparticles immobilized within a HypoG el resin has been prepared in the absence of any ligands using an extensive cross-linking method.This newly developed nanocatalyst was characterized by N_2 adsorption-desorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),scanning electron microscopy(SEM),energy dispersive X-ray(EDX),Fourier transform infrared spectroscopy and inductively coupled plasma-mass spectrometer(ICP-MS)techniques.TEM and XRD results revealed that the Pd nanoparticles were well dispersed with diameters in the range of 4–12 nm,and an average size of about 8 nm.The cross-linked Pd catalyst demonstrated excellent catalytic activity towards the synthesis of a series of biaryl compounds by the reaction of various aryl halides(e.g.,bromides andiodides)with phenylboronic acid in the presence of tetrabutylammonium bromide.ICP-MS analysis indicated that there was only 0.25%weight loss of Pd(0.55±0.02 ppm)from the supported catalyst after the first cycle reaction.Furthermore,the catalyst showed excellent reusability(up to five uses)with consistently high levels of catalytic activity following its recovery by filtration.     

Morphology,Crystallization Behavior and Tensile Properties of β-Nucleated Isotactic Polypropylene Fibrous Membranes Prepared by Melt Electrospinning

β-nucleated isotactic polypropylene(iPP) fibers with diameters less than 5 μm were prepared through melt electrospinning. The effects of electrospinning process and rare earth β-nucleating agent(WBG) on the crystal structure of iPP fibers were investigated. The results indicate that the addition of WBG can improve the fluidity of iPP melt remarkably and help the formation of fine fibers with thinner diameter, while the electrostatic force applied on the iPP melt is not favorable for the formation of β-crystal in iPP fibers. In addition, the morphology and crystalline structure of WBG/iPP electrospun fibers depended on the content of WBG. Both the crystallinity and the percentage of β-crystal form of WBG/iPP electrospun fibers increase with the rise of the content of nucleating agent, which endows the prepared electrospun fibers excellent mechanical properties. The β-nucleated iPP electrospun fibrous membranes prepared in this study can be used for protective clothing material, filtration media, reinforcement for composites and tissue engineering scaffolds.     

Synthesis of monodisperse hollow polymer microspheres with functional groups by distillation precipitation polymerization

<正>Monodisperse hollow polymer microspheres having various functional groups on the shell-layer,such as carboxylic acid,pyridyl and amide,were prepared by two-stage distillation precipitation polymerization in neat acetonitrile in the absence of any stabilizer or additive,during which monodisperse poly(methacrylic acid)(PMAA) afforded from the first-stage polymerization was utilized as the seeds for the second-stage polymerization.The shell layer with different functional groups was formed during the second-stage copolymerization of either divinylbenzene(DVB) or ethyleneglycol dimethacrylate(EGDMA) as crosslinker and the functional comonomers,in which the hydrogen-bonding interaction between the carboxylic acid group of PMAA core and the functional groups of the corresponding comonomers,including carboxylic acid,amide and pyridyl,played an essential role for the formation of monodisperse core-shell functional microspheres.The hollow polymer microspheres were then developed after the subsequent removal of PMAA cores by dissolution in ethanol under basic condition.Transmission electron microscopy(TEM) and scanning electron microscopy (SEM) were used to determine the morphology of the resultant PMAA core,functional core-shell microspheres and the corresponding hollow polymer microspheres with different functional groups.FT-IR spectra confirmed the successful incorporation of the various functional groups on the shell layer of the hollow polymer microspheres.     

Preparation,Characterization,and in vitro Release of Biodegradable Erythromycin-gelatin Microspheres

Blank and erythromycin-loaded gelatin microspheres were successfully fabricated via emulsion chemical- crosslinking technique. The surface morphology of the microspheres was characterized by scanning electron microscope（SEM） and optical microscope. The results show that the microspheres were spherical and smooth. The particle average size of erythromycin-loaded microspheres was found to be 20.6 μm, with a high purity of more than 90% and with a good dispersibility. The microspheres could be obtained in a high yield. Erythromycin released from the microspheres was monitored in buffer and artificial body fluid at 37 ℃. Average drug content was 27.2%, and erythromycin-loaded gelatin microspheres showed good release profiles with a nearly constant release during 4-8 h in artificial body fluid in vitro degradation studies. These gelatin microspheres are useful for studying and developing various drug-delivery systems.     

Stability of pyrrolidone derivatives against γ-ray irradiation

To evaluate the stability of N-alkylated pyrrolidone derivatives(NRPs),which are supposed to be used as precipitants for U(VI) and Pu(IV,VI) species in HNO 3 media,under irradiation environment,some candidate NRPs were irradiated by γ-ray.Irradiation to HNO 3 solutions up to 6 mol dm 3(= M) containing 2 M N-n-butyl-2-pyrrolidone(NBP),one of NRPs with lower hydrophobicity,has revealed that the residual ratios of NBP in the samples of HNO 3 up to 3 M decreased identically and linearly.Approximately 20% of NBP was found to be degraded after the irradiation at 1 MGy.It was also found that the decrease in the precipitation ratio of UO 2 2+(P.R.,%) was gentle and that the P.R.values were relatively in accordance with the residual ratios of NBP.On the other hand,the degradation of the samples irradiated in 6 M HNO 3 was found more distinguished.It was proposed from the analyses of degraded compounds that the degradation of NBP in HNO 3 by γ-ray irradiation started from the cleavage of the pyrrolidone ring by the addition of oxygen atom originating from HNO 3,followed by the formation of chain compounds by the successive addition of oxygen,leading to the generation of oxalic acid and acetic acid.The stability of other NRPs in 3 M HNO 3 was evaluated to be nearly identical with that of NBP except lower P.R.values of the samples containing NRPs with higher hydrophobicity irradiated at more than 0.5 MGy.     

SURFACE OF GELATIN MODIFIED POLY(L-LACTIC ACID)FILM

In this paper, the surface structure of poly(L-lactic acid) (PLLA) film modified with gelatin was investigated. ThePLLA film specimens were treated directly with aqueous alkali solution to provide their surfaces with carboxyl groups, sothat these functional groups could become the reactive sites for gelatin immobilization. The functional groups of the PLLAfilms were identified by ATR-FTIR spectra and XPS spectra, the changes in surface morphology were observed by usingenvironmental scanning electron microscopy (ESEM), and the hydrophilicity of modified PLLA films was examined bywater contact angle measurement. Experimental results showed that the gelatin was immobilized with water-solublecarbodiimide (EDC) onto the PLLA film's surfaces, and the gelatin content on the polymer surface was related to carboxylicgroup formed in the controlled hydrolysis process. Rough surfaces caused by hydrolysis will predominantly favor the adhesion and growth of cell; and the hydrophilicity of these surfaces after the modification procedure is enhanced.     

ELECTROSPRAYING/ELECTROSPINNING OF POLY(γ-STEARYL-LGLUTAMATE):FORMATION OF SURFACES WITH SUPERHYDROPHOBICITY

Electrospraying/electrospinning of poly(γ-stearyl-L-glutamate) (PSLG) was investigated on a series solutions with different concentrations in chloroform.Field emission scanning electron microscopy (FESEM) and attenuated Iotal reflectance Fourier transform infrared spectroscopy (FT-IR/ATR) were used to characterize the morphology and structure of the electrosprayed/electrospun polypeptide mats.It was found that electrospraying of PSLG with concentrations lower than 16 wt% afforded beads,while microfibers ...     

SYNTHESIS OF NOVEL HYDROPHILIC BIODEGRADABLE POLYESTER WITH FUNCTIONALIZED SIDE CHAIN GROUPS*

A substituted glycolide, 3-bencyloxymethyl-1, 4-dioxane-2, 5-dione, was synthesized. It is a suitable precursor forthe preparation of a new hydrophilic biodegradable poly(α-hydroxy acid). The polymerizations were carried out in bulk inthe presence of Sn(Oct)_2 at 120-140℃. The resulting polymers were subjected to hydrogenolysis with a Pd/C catalyst in amixed solvent to remove the protecting benzyl groups. A novel poly(α-hydroxy acid) with pendant hydroxy groups wasobtained. The hydrophilicity of the resulting polymer was evaluated preliminarily.