乙酸正丁酯的合成

以乙酸和正丁醇为原料,在硫酸氢钾催化下合成了乙酸正丁酯;考察了反应时间、醇酸比、催化剂用量、带水剂用量及催化剂的重复使用对酯化率的影响.结果表明:当正丁醇用量为0.1mol,乙酸用量为0.135mol,催化剂硫酸氢钾用量为0.8g,带水剂环己烷用量为8mL时,反应的酯化率达95.2%.     

磷钨酸催化合成乙酸戊酯

以磷钨酸为催化剂,冰醋酸和戊醇为原料,催化合成了乙酸戊酯.探讨了催化剂用量、醇酸比、反应时间等对酯化反应的影响.研究结果表明:取冰醋酸40mL,正戊醇25mL,磷钨酸2.0g,反应时间为2h时,酯的产率大于80%.     

乙酸异丙酯的合成

以乙酸和异丙醇为原料,硫酸氢钠为催化剂,合成了乙酸异丙酯;考察了反应时间、酸醇比、催化剂用量、带水剂用量对酯化率的影响,确定了最佳酯化反应条件:反应时间60min,酸醇的物质的量的比1∶0.8,催化剂用量0.8g,带水剂用量8mL.在最佳反应条件下,酯化率最高可达84.3%.     

双磺酸基功能化多酸类离子液体的制备及其催化合成乙酸正丁酯

制备了四种多酸类离子液体,并应用于乙酸与正丁醇的酯化反应,发现双磺酸基功能化的多酸类离子液体[BS_2DABCD]HPW_(12)O_(40)呈现出最高的催化活性.研究了反应温度、催化剂用量、乙酸与正丁醇的物质的量的比和反应时间等因素对乙酸正丁酯产率的影响.在最佳反应条件下,乙酸正丁酯的产率达到82%.催化剂重复使用4次后,乙酸正丁酯的产率没有明显降低,显示出良好的重复利用性.     

ZnMn2O4纳米催化剂制备及催化合成乙酸正丁酯

本文以共沉淀法制备了四方晶系锌锰复合氧化物ZnMn2O4纳米催化剂。采用X射线粉末衍射(XRD)和透射电子显微镜(TEM)测试技术对样品进行了分析表征,结果表明所合成的催化剂为粒径均匀的纳米粒子,平均粒径在20-50 nm,具有较好的分散性。实验考察了所制备的ZnMn2O4纳米催化剂对乙酸和正丁醇酯化反应的催化活性,表明ZnMn2O4对乙酸正丁酯的合成有较高的催化活性;探讨了催化剂焙烧温度、催化剂用量、酸醇摩尔比以及反应时间对酯化率的影响,确定了适宜的酯化反应条件,以焙烧温度为300 ℃制备的ZnMn2O4为催化剂,在催化剂用量为0.3%(以反应物总质量计)、酸醇摩尔比n(酸):n(醇)=1.8:1、反应时间为4 h、酯化反应温度120 ℃的条件下,酯化率可达92.53%。     

酸功能化离子液体催化合成柠檬酸三丁酯

合成并表征了酸功能化离子液体,用于催化合成柠檬酸三丁酯(TBC).通过考察各种离子液体的催化活性及重复使用性能,选定酸功能化离子液体[HSO3-pmim]HSO4为催化合成TBC的催化剂.研究了催化剂用量、醇酸摩尔比、反应时间等因素对酯化反应的影响,得到其较佳工艺条件为:催化剂用量为反应物总质量的8·0%,醇酸摩尔比为5·5∶1,反应温度110~150℃,反应时间3h.此条件下,酯化率达到99·0%.分离出的离子液体未经任何处理重复使用8次后,酯化率仍为95·2%.     

稀土固体超强酸SO2-4/TiO2/La3 +催化合成丙酸苄酯

采用浸渍法制备了稀土固体超强酸SO2-4/TiO2/La3+,并运用IR、XRD和Hammett指示剂法对其进行了表征.以制备的固体超强酸SO2-4/TiO23+为催化剂、丙酸和苯甲醇为原料合成了丙酸苄酯.考察了催化剂的制备条件及合成条件对酯化率的影响,结果显示催化剂最佳制备条件:钛前体氧化物的浸渍液为含0.07 mol·L-1 La3+的硫酸溶液,焙烧时间3 h,焙烧温度500℃.最佳反应条件:醇酸摩尔比为1:2、催化剂用量为苯甲醇用量的9.3%、反应时间3 h、反应温度120℃,酯化率达84.0%以上.用IR、1H-NMR等手段对产品进行了表征.     

稀土固体超强酸SO4^2-／TiO2／La^3＋催化合成丙酸苄酯

采用浸渍法制备了稀土固体超强酸SO2-4/TiO2/La3+,并运用IR、XRD和Hammett指示剂法对其进行了表征.以制备的固体超强酸SO2-4/TiO23+为催化剂、丙酸和苯甲醇为原料合成了丙酸苄酯.考察了催化剂的制备条件及合成条件对酯化率的影响,结果显示催化剂最佳制备条件钛前体氧化物的浸渍液为含0.07 mol·L-1 La3+的硫酸溶液,焙烧时间3 h,焙烧温度500℃.最佳反应条件醇酸摩尔比为12、催化剂用量为苯甲醇用量的9.3%、反应时间3 h、反应温度120℃,酯化率达84.0%以上.用IR、1H-NMR等手段对产品进行了表征.     

乙酸异戊酯的合成

以乙酸和异戊醇作为原料,利用SnCl4催化作用下的酯化反应合成了乙酸异戊酯;研究了反应时间、酸醇的物质的量之比、催化剂用量、带水剂用量等因素对产物收率的影响,并确定了优化反应条件.结果表明,优化反应条件为:反应时间60min,酸醇物质的量之比1∶0.8(乙酸5.76mL),催化剂用量0.35g,带水剂用量10mL.在优化反应条件下,产物收率最高可达86.3%.     

活性炭负载硅钨酸催化合成乙酸正丁酯

以活性炭负载硅钨酸为催化剂,乙酸和正丁醇为原料合成乙酸正丁酯.优化的反应条件如下:在冰乙酸0.253mol、正丁醇0.22mol、催化剂用量为反应物总量的1.5%(质量分数)、反应温度115℃,反应时间为90min的条件下,酯化率可达97.8%.产品纯度>98%,并且催化剂可以多次使用活性没有明显下降.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.