基于表面重建螺旋型铂铱电极的葡萄糖生物传感器

通过对螺旋型铂铱电极表面进行化学腐蚀和电化学沉积铂纳米粒子实现电极表面的重建和优化,研究了螺旋型铂铱电极在不同腐蚀时间和电沉积时间下的形貌及对过氧化氢(H2O2)的催化活性.对表面重建的工作电极涂覆氧化酶和半透膜,制备出了铂纳米粒子/葡萄糖氧化酶/环氧聚氨酯酶电极,并将其用作葡萄糖传感器的工作电极.传感器计时电流检测结果表明,表面重建后的酶电极传感器对葡萄糖的检测范围扩大为2~45 mmol/L,优于裸铂铱酶电极传感器,电流响应值和灵敏度得到明显提升,同时传感器还具有良好的稳定性和选择性.     

纳米铂颗粒修饰薄膜金电极的新型葡萄糖传感器研究

在没有引入电子媒介体条件下,为了提高传感器的响应灵敏度,降低工作电位,利用电化学沉积法在薄膜金电极表面修饰纳米铂颗粒,并通过戊二醛固定酶的方法制备了一种新型生物传感器。研究了在薄膜金电极上修饰纳米铂颗粒前后传感器对低浓度葡萄糖的响应影响。结果表明,纳米铂颗粒修饰后所制备的葡萄糖传感器工作电位下降为0.4 V,测定葡萄糖的检出限从100μmol/L下降到10μmol/L。传感器对10~1300μmol/L低浓度葡萄糖的响应灵敏度为50.8 nA/(cm2μmol/L);响应时间30 s;r为0.9974;传感器精密度为2.1%,并具有较好的稳定性。     

壳聚糖-纳米金-葡萄糖氧化酶生物传感器的制备及其应用于葡萄糖的测定

采用了一种简便快捷的电沉积方法制备了壳聚糖-纳米金复合膜并应用于葡萄糖生物传感器的构建.氯金酸和壳聚糖的混合液在玻碳电极表面电化学还原为金纳米粒子,再将葡萄糖氧化酶通过戊二醛交联的方式固定在纳米金复合膜修饰的玻碳电极表面,制成一种新型的葡萄糖氧化酶生物传感器.该传感器对葡萄糖的响应十分快速,在5 S内即达到平衡.测定葡萄糖的线性范围为20μmol·L-1～5 mmol·L-1,检出限(3S/N)为12μmol·L-1.     

双重信号放大的乙酰胆碱酯酶电化学传感器检测有机磷农药

基于生物催化纳米金的生成和纳米金粒子电催化银沉积实现两次信号放大的原理,构建了一种快速、灵敏的乙酰胆碱酯酶电化学传感器,用于检测有机磷农药。固定在金电极表面的乙酰胆碱酯酶催化底物氯化乙酰硫代胆碱产生硫代胆碱,硫代胆碱还原氯金酸生成纳米金,将电极置于1.0 mol/L NH3-2.0×10#3mol/L AgNO3的银增强液中,由于纳米金粒子的催化作用,在#0.10 V的电压下,银只会沉积在生成的纳米金表面,沉积银的量与生成的纳米金颗粒的数目成正比,通过线性扫描伏安法定量检测沉积的银。在0.1~1000μg/L范围内,乙酰胆碱酯酶的抑制剂马拉硫磷的浓度与银的溶出峰呈线性,线性方程为i pa=149.9-40.49lgC(r=0.9963),检出限为0.05μg/L。本方法极大地提高了传感器检测的灵敏度。将其应用于湘江水样中马拉硫磷的检测,回收率在95.5%~102.2%之间,结果满意。     

基于纳米MnO_2二茂铁修饰丝网印刷碳电极的尿酸生物传感器研究

在丝网印刷碳电极上修饰纳米MnO2,并利用戊二醛和β-环糊精交联固定尿酸酶,以二茂铁作为电子媒介体,研制用于测定尿酸浓度的生物传感器.实验结果表明,纳米MnO2降低了电子媒介体二茂铁的氧化还原反应电位,且纳米MnO2与电子媒介体二茂铁在尿酸生物传感器中表现出协同增效效应.该尿酸生物传感器线性响应范围是6.0×10-6～1.2×10-3 mol/L,检出限为3.0×10-6 mol/L.用纳米MnO2修饰酶电极,改善了电极表面条件,加快了电极反应速率,提高了尿酸传感器的灵敏度.     

基于Sol-gel膜和多壁碳纳米管/铂纳米颗粒增效的电流型L-乳酸生物传感器

构建了基于多壁碳纳米管(Multi-walled carbon nanotubes,MWCNTs)和铂纳米颗粒(Pt-nano)的电流型L-乳酸生物传感器。将Sol-gel膜覆盖在L-乳酸氧化酶(L-lactate oxidase,LOD)和MWCNTs/Pt-nano修饰的电极表面。实验结果表明:传感器的最佳工作条件为:检测电压0.5V;缓冲液pH6.4;检测温度25℃。此传感器的响应时间为5s,灵敏度是6.36μA/(mmol/L)。连续检测4星期其活性仍保持90%,线性范围为0.2～2.0mmol/L,且抗干扰能力强。在实际血样的检测中,此传感器与传统的分光光度法具有很好的一致性。     

非图案化法制备柔性连续葡萄糖监测传感器

以聚多巴胺作为前驱体,在聚酰亚胺薄膜表面化学沉积一层牢固致密的金层,以该镀金薄膜两面的金层作为基体电极,在其中一面镀铂黑作为参比-对电极,在另一面依次电沉积铂黑层、电泳形成Nafion/碳纳米管网络层、电吸引形成葡萄糖氧化酶层构成工作电极,并整体涂覆聚氨酯外膜,制备了一种柔性葡萄糖传感器.考察了此传感器对葡萄糖的检测性能,以及各层表面形态结构对传感器性能的影响.传感器在0.3V的工作电位下对葡萄糖的线性响应范围是2.0 ～ 32.0 mmol/L,响应灵敏度为25 μA· (mmol/L)-1·cm-2,检出限为0.05 mmol/L (S/N=3),且传感器有良好的长期稳定性和抗干扰性,可用于皮下连续血糖监测.     

全血尿酸生物传感器的研制及临床应用

研制了一种利用全血来测试尿酸含量的安培型生物传感器。采用铁氰化钾作为媒介体,将尿酸氧化酶固定在羧甲基纤维素钠处理过的碳电极表面,研制成一种尿酸生物传感器。该传感器在恒电位0.3V和尿酸氧化酶的催化作用下,使被检测物尿酸氧化,铁氰化钾还原,在电极表面产生氧化-还原峰,利用安培法可对尿酸进行间接测定。该传感器经临床测试,尿酸的测定范围可达25~200mg/L,10s内即可达到稳态电流,测试结果的线性范围较好,相关系数为0.9987。另外,尿酸传感器具有好的抗干扰性,测试精度高、重复性好,RSD<2%。     

基于Fe3O4@Au复合纳米粒子标记抗体的电化学免疫方法用于水体中大肠杆菌的检测

合成了Fe₃O₄@Au复合纳米粒子作为辣根过氧化酶标记抗体的载体, 并将该复合纳米粒子标记物应用于电化学放大免疫分析. 将电子媒介体硫堇聚合在玻碳电极表面, 以纳米金作为固定大肠杆菌抗体的基底, 通过辣根过氧化酶催化溶液中H₂O₂产生的电流信号来测定大肠杆菌. 实验结果表明, 该方法对水体中大肠杆菌检测的线性范围为50～1×10⁵ cfu/mL, 检出限为20 cfu/mL. 对过富集后的实际水样进行测定, 该法结果表明, 对水体中大肠杆菌的检测灵敏度达到2 cfu/mL.     

层层自组装纳米金与乙酰胆碱酯酶电化学生物传感器检测有机磷农药

采用层层自组装技术制备了快速检测有机磷农药的生物传感器,利用带正电荷的高分子聚电解质聚二烯丙基二甲基氯化铵(PDDA)将乙酰胆碱酯酶(AChE)和金纳米粒子(AuNPs)通过静电力逐层固定到玻碳电极(GCE)表面,并采用交流阻抗和微分脉冲伏安法研究了此生物传感器的电化学行为。由于金纳米粒子优异的电催化性能和良好的生物相容性,使固定化的乙酰胆碱酯酶对其底物具有更高的亲和力和更快的响应速度。实验结果表明:修饰金纳米粒子后,传感器的氧化电流明显增大,在4.6×10-5～5.3×10-3mol/L范围内,固定化酶的抑制率与甲基对硫磷浓度的对数成正比,检出限为7.6×10-6mol/L。该生物传感器具有制备方法简便、成本低、灵敏度高等优点,已成功用于蔬菜样品中甲基对硫磷含量的测定。     

Comparison of biosensors based on gold and nanocomposite electrodes for monitoring of malic acid in wine

Amperometric biosensors based on a gold planar electrode and on two types of nanocomposite electrodes consisting of multi-walled carbon nanotubes for the determination of L-malic acid designed for wine-makers were developed. The biosensors designed for wine-makers were constructed by immobilization of L-malate dehydrogenase and diaphorase within chitosan layers on the surface of the electrodes. The coenzyme NAD+ and the electrochemical mediator ferricyanide were present in the measuring solution. The current resulting from re-oxidation of produced ferrocyanide was measured at a working potential of +300 mV against an Ag/AgCl reference electrode. The biosensor based on a gold electrode showed linearity over the range 10–520 μM with a detection limit of 5.41 μM. Calibration curves for biosensors utilizing nanocomposites were obtained both with the linear range of 10 to 610 μM. The detection limits were 1.57 and 1.77 μM, respectively. The biosensors showed satisfactory operational stability (no loss of sensitivity after 30 consecutive measurements) and storage stability (90% of the initial sensitivity after one year of storage at room temperature). The results obtained from measurements of wine samples were in a good correlation with the standard HPLC method. Satisfactory biosensor sensitivity, specificity and stability allowed their successful commercialization.     

Speciation of chromium using chronoamperometric biosensors based on screen-printed electrodes

Chronoamperometric assays based on tyrosinase and glucose oxidase (GOx) inactivation have been developed for the monitoring of Cr(III) and Cr(VI). Tyrosinase was immobilized by crosslinking on screen-printed carbon electrodes (SPCEs) containing tetrathiafulvalene (TTF) as electron transfer mediator. The tyrosinase/SPC_TTFE response to pyrocatechol is inhibited by Cr(III). This process, that is not affected by Cr(VI), allows the determination of Cr(III) with a capability of detection of 2.0 ± 0.2 μM and a reproducibility of 5.5%. GOx modified screen-printed carbon platinised electrodes (SPC_PtEs) were developed for the selective determination of Cr(VI) using ferricyanide as redox mediator. The biosensor was able to discriminate two different oxidation states of chromium being able to reject Cr(III) and to detect the toxic species Cr(VI). Chronoamperometric response of the biosensor towards glucose decreases with the presence of Cr(VI), with a capability of detection of 90.5 ± 7.6 nM and a reproducibility of 6.2%. A bipotentiostatic chronoamperometric biosensor was finally developed using a tyrosinase/SPC_TTFE and a GOx/SPC_PtE connected in array mode for the simultaneous determination of Cr(III) and Cr(VI) in spiked tap water and in waste water from a tannery factory samples.     

Electrochemical determination of melamine using oligonucleotides modified gold electrodes

A novel and simple electrochemical method for determination of melamine is developed based on oligonucleotides film modified gold electrodes. The electrochemical probe of ferricyanide was used to investigate the interactions between oligonucleotides and melamine. Results of cyclic voltammetries, differential pulse stripping voltammetries, electrochemical impedance spectrometry and atomic force microscope, proved that melamine might interact with oligonucleotides mainly through electrostatic and hydrogen-bonding interactions. The interactions between oligonucleotides and melamine lead to the increase in the peak currents of ferricyanide, which could be used for electrochemical sensing of melamine. The redox peak currents of ferricyanide were linear with the concentration of melamine in the range from 3.9 × 10⁻⁸ to 3.3 × 10⁻⁶ M with a linear coefficiency of 0.990. The detection limit was 9.6 × 10⁻⁹ M. The proposed electrochemical biosensor is rapid, convenient and low-cost for effective sensing of melamine. Particularly, the proposed method was applied successfully to the determination of melamine in milk products, and the recovery was 95%.     

Three-phase electrodes: simple and efficient tool for analysis of ion transfer processes across liquid-liquid interface—twenty years on

In this review, we focus on major achievements of the three-phase electrode methodology applied for studying ion transfers across an interface between two immiscible liquids. Exactly 20 years ago, the group of electrochemists led by Fritz Scholz, invented an elegant and simple set up suitable to get access to the thermodynamics of ion transfers across liquid/liquid interface. Within the last two decades, besides determination of thermodynamics of the transfer of many important ionic substances, three-phase electrodes have been applied for many other purposes. Thermodynamics of interfacial chemical reactions, kinetics of ion and electron transfer, interfacial catalysis, recognition of chiral ions, synthesis of nano-particles, and biosensor development are some of the milestones achieved by application of three-phase electrodes. While elaborating briefly major achievements, future perspectives of this simple, but powerful electrochemical tool, have been also envisaged.

     

Impact of Polycyclic Aromatic Hydrocarbons on the Electrochemical Responses of a Ferricyanide Probe at Template‐Modified Self‐Assembled Monolayers on Gold Electrodes

The impact of polycyclic aromatic hydrocarbons (PAHs) on the electrochemical responses of a ferricyanide probe using gold electrodes coated with template‐containing self‐assembled monolayers (SAMs) was investigated using cyclic voltammetry and square‐wave voltammetry. The thiolated compounds that were used to form SAMs included 1‐hexadecanethiol, 11‐mercapto‐undecanoic acid, 11‐mercaptoundecanol, and (3‐mercaptopropyl) trimethoxysilane (MPTS). When the SAMs were formed from 1‐hexadecanethiol or 11‐mercapto‐undecanoic acid in the absence of pyrene, the SAM‐modified electrodes prohibited access of the ferricyanide probe and no impact of pyrene was observed. SAM‐modified electrodes (all except for MPTS) that were formed in the presence of pyrene then washed free of pyrene showed an increase in accessibility of the probe ferricyanide upon the addition of pyrene to the electrolyte solution. When electrodes were modified with MPTS to form stabilized SAMs in the presence of pyrene, however, a reduced redox current for the ferricyanide probe was observed with increased pyrene or naphthalene in the electrolyte solution. A degree of selectivity was noted in that this current response was not observed for addition of benzo[a]pyrene.     

A nano-functionalized real-time electrochemiluminescent biosensor for alanine transaminase assay

An electrochemiluminescent (ECL) biosensor was constructed for selective assay of alanine aminotransferase (ALT) based on the enzymatically catalyzed oxidation of pyruvate by pyruvate oxidase (PYOD). The composite of potassium ferricyanide and carbon nanotube was adopted to pre-functionalize the basal platinum electrode while the potassium ferricyanide acted as the activator of PYOD. The ALT catalyzed the reaction of L-alanine and-ketoglutarate to produce pyruvate which could be further enzymatically oxidiz...     

基于碳纳米管修饰电极的胆碱电化学发光生物传感器研制

在碳纳米管(CNTs)和K3Fe(CN)6修饰的铂电极上吸附固定胆碱氧化酶,以鲁米诺为发光试剂,研制了胆碱电化学发光(ECL)生物传感器。CNTs可有效提高电极表面的电荷传输能力、提高电极表面的生物相容性和对酶分子的固载能力;K3Fe(CN)6对酶活性具有激活作用,同时对H2O2增敏的鲁米诺ECL有增强作用,均有利于提高传感器的检测灵敏度。研究表明,将CNTs分散液与K3Fe(CN)6混合,滴涂修饰在Pt电极上,吸附固定胆碱氧化酶,制备传感器。此传感器在含有8×10-6mol/L鲁米诺的磷酸盐缓冲液(pH7.4)、30℃条件下产生的ECL强度与胆碱浓度在1×10-7～4×10-3mol/L范围内呈线性关系,相关系数为0.994,检出限为1.2×10-8 mol/L。此生物传感器应用于鼠血样中胆碱的测定,测得结果为2.68 mg/L,平均回收率为101.1%。传感器具有快速、稳定和重现性好等特点,有望应用于常规分析。     

Effects of pretreatments and modifiers on electrochemical properties of carbon paste electrodes

The electrochemical properties of carbon paste electrodes (CPEs), including unmodified and modified with protein and polycations, were investigated by impedance spectroscopy (IS) using ferricyanide and ferrocene monocarboxylic acid (FcMA) as redox probes. Various electrochemical pretreatments were applied to the unmodified CPE. The heterogeneous charge transfer rate constant of ferro/ferricyanide couple is enhanced by 2 to 10 times compared with that obtained at untreated electrodes. It was found that for ferricyanide the more suitable pretreatments are successive cyclic voltammetric scans, cathodization and a square wave-like stepping rather than high-potential anodization. However, the pretreatment only exhibits a slight effect on the kinetics of FcMA. At the CPEs containing modifier, the electron transfer rate of the redox couple depends more on the pH of electrolyte solution if ferro/ferricyanide is used. The results can be explained by the differently charged states of the CPEs that were caused by the protonation or deprotonation of the modifiers in various pH solutions and demonstrate the importance of the electrostatic interaction on the kinetics of the highly polar species such as ferricyanide. The different adsorptive behavior of ferricyanide and FcMA is also discussed.     

纳米材料在电化学生物传感器中的应用及纳米仿生界面的构建

对1995～2011年间各种纳米材料,包括金属纳米粒子、量子点纳米材料、碳纳米材料、复合纳米材料等在电化学生物传感器中的应用及纳米仿生界面的构建进行了综述。