Automated clean-up, separation and detection of polycyclic aromatic hydrocarbons in particulate matter extracts from urban dust and diesel standard reference materials using a 2D-LC/2D-GC system

A multidimensional, on-line coupled liquid chromatographic/gas chromatographic system was developed for the quantification of polycyclic aromatic hydrocarbons (PAHs). A two-dimensional liquid chromatographic system (2D-liquid chromatography (LC)), with three columns having different selectivities, was connected on-line to a two-dimensional gas chromatographic system (2D-gas chromatography (GC)). Samples were cleaned up by combining normal elution and column back-flush of the LC columns to selectively remove matrix constituents and isolate well-defined, PAH enriched fractions. Using this system, the sequential removal of polar, mono/diaromatic, olefinic and alkane compounds from crude extracts was achieved. The LC/GC coupling was performed using a fused silica transfer line into a programmable temperature vaporizer (PTV) GC injector. Using the PTV in the solvent vent mode, excess solvent was removed and the enriched PAH sample extract was injected into the GC. The 2D-GC setup consisted of two capillary columns with different stationary phase selectivities. Heart-cutting of selected PAH compounds in the first GC column (first dimension) and transfer of these to the second GC column (second dimension) increased the baseline resolutions of closely eluting PAHs. The on-line system was validated using the standard reference materials SRM 1649a (urban dust) and SRM 1975 (diesel particulate extract). The PAH concentrations measured were comparable to the certified values and the fully automated LC/GC system performed the clean-up, separation and detection of PAHs in 16 extracts in less than 24 h. The multidimensional, on-line 2D-LC/2D-GC system eliminated manual handling of the sample extracts and minimised the risk of sample loss and contamination, while increasing accuracy and precision.

Determination of total biodiesel fatty acid methyl, ethyl esters, and hydrocarbon types in diesel fuels by supercritical fluid chromatography-flame ionization detection

A method for determining total biodiesel methyl and ethyl ester content in diesel fuels by supercritical fluid chromatography-flame ionization detection (SFC-FID) is developed. A silica column typically used for determining aromatics in conventional diesel fuels by ASTM D5186 is back-flushed after separation of the hydrocarbons to allow elution of the various esters as a single "total biodiesel" distinct peak. The modification concurrently allows the determination of total aromatic hydrocarbons and their distribution as mono- and polynuclear compounds, as described in the current version of D5186. The instrument response is linear from 1.0% to 50% biodiesel esters with a signal-to-noise ratio of 25 at the 0.1% level. The short-term relative standard is 0.8%. Normalized percent quantitation using a hydrocarbon response factor of 1.00 and an ester response factor of 1.19 provide an average percentage error of 1.8% when measuring actual biodiesel/hydrocarbon fuel blends. The ester response factor is the average of the response factors of 10 pure ester compounds. These responses are calculated from respective solutions of each ester and the four compounds, hexadecane, toluene, tetralin, and naphthalene, as used for the D5186 response factor mixture.     

Coupled LC-GC-MS for on-line clean-up,separation, and identification of chlorinated polycyclic aromatic hydrocarbons at picogram levels in urban air

Coupled liquid chromatography – gas chromatography – mass spectrometry (LC-GC-MS) has been applied for on-line clean up, separation, and identification of chlorinated polycyclic aromatic hydrocarbons (CI-PAHs). A loop-type interface was used to couple the liquid chromatograph on-line with the GC-MS, and concurrent solvent evaporation was used for sample transfer. A back-flush technique was used in conjunction with a two-dimensional column system for isolation of CI-PAHs and polycyclic aromatic hydrocarbons (PAHs). This fraction was transferred on-line to the GC and separated on a capillary column. Selective and sensitive detection of CI-PAHs in the GC eluate was obtained by negative ion chemical ionization (NICI) mass spectrometry and selected ion monitoring (SIM). The combined on-line system for isolation, separation, and identification showed high precision and accuracy, and demonstrated a linear response from 1 to 1000 pg for chlorinated PAHs. The estimated detection limit was 250 fg for 1-chloropyrene and 1,6-dichloropyrene. The technique was demonstrated by analysis of urban air samples. The low detection limit made it possible to use the technique for analysis of personally carried monitoring equipment for measurement of exposure to CI-PAHs in the work environment.     

Liquid crystal stationary phases for gas chromatography and supercritical fluid chromatography

Novel monomeric and polymeric liquid crystalline compounds were synthesized as stationary phases for gas chromatography (GC) and supercritical fluid chromatography (SFC). Monomeric liquid crystalline compounds were used in packed column gas chromatography for the separation of isomeric aromatic compounds and insect sex pheromones. Liquid crystalline polymers possess long nematic ranges and a uniform coating was easily achieved in glass and fused silica capillaries, which could stand temperatures up to 250°C in GC and pressures of 200 MPa at 160°C in SFC. The columns provide excellent selectivity and resolution for fused ring aromatic compounds such as the isomers anthracene and phenanthrene or triphenylene and chrysene.     

Structure-type separation of diesel fuels by solid phase extraction and identification of the two- and three-ring aromatics by capillary GC-mass spectrometry

A simple and effective solid phase extraction (SPE) method using silica gel micro glass columns has been developed for the separation of diesel fuel into groups of aliphatic, and mono-, di- and polyaromatic hydrocarbons. It is based on a stepwise gradient of dichloromethane in n-pentane. The resulting fractions were analyzed by capillary gas chromatography with a flame ionization detector and coupled gas chromatography-mass spectrometry. Commercially available standards, and retention indices and mass spectra were used for identification of individual aromatic compounds. The principal polycyclic aromatic hydrocarbons (PAHs) in diesel fuel are naphthalene, biphenyl, fluorene, phen-anthrene and their alkylated derivatives. Sulfur-containing PAHs are mainly represented by methyl-substituted dibenzo-thiophenes.     

Capillary electrophoretic separation of polycyclic aromatic sulfur heterocycles

Capillary electrophoresis (CE) was used to separate polycyclic aromatic sulfur heterocycles (PASHs), a class of compounds that occurs in fossil fuels and refined products of petroleum. An electric charge was introduced into the compounds through methylation or phenylation of the sulfur atom. Separations of standard PASHs that are expected to be present in industrially desulfurized fuels showed that CE possessed a higher resolution than reversed phase liquid chromatography. The CE method can separate all the monomethylbenzothiophenes; this is not achieved in capillary gas chromatography. A linear relationship was found between migration time and the calculated volume of the compounds. The PASHs in deeply desulfurized diesel were separated after preconcentration, and the electropherogram was compared with the chromatograms from GC and HPLC. Finally, derivatized PASHs are often enantiomeric and the enantiomers can be separated if a suitable cyclodextrin is added to the running buffer.     

Preparation,characterization and application of a new 25,27‐bis‐[2‐(5‐methylthiadiazole)thioethoxyl]‐26,28‐dihydroxy‐para‐tert‐butyl calix[4]arene stationary phase for HPLC

A new para‐tert‐butylcalix[4]arene column containing thiadiazole functional groups was prepared and used for the separation of polycyclic aromatic hydrocarbons, phenolic compounds, aromatic amines, benzoic acid and its derivatives by high‐performance liquid chromatography (HPLC). The effect of organic modifier content in the mobile phase on retention and selectivity of these compounds were investigated. The results indicate that the stationary phase behaves like reversed‐phase packing. However, hydrogen bonding, π–π and inclusion interactions seem to be involved in the separation process. The column has been successfully employed for the analysis of clenbuterol in pork and pig casing; the limit of detection and the limit of quantitation for this method by HPLC‐UV detection was 0.03 and 0.097 μg/mL, respectively; the method is demonstrated to be suitable and a competitive alternative analytical method for the determination of clenbuterol.     

Clinical and pharmaceutical applications of packed-column supercritical fluid chromatography

Packed-column supercritical fluid chromatography (pSFC) is a fast separation technique that combines the properties of HPLC and GC. pSFC with carbon dioxide as the mobile phase and packed silica column as the stationary phase possesses the properties of normal phase mechanism; however, the addition of modifiers to the mobile phase allows the separation of relatively polar compounds. In spite of its many positive attributes, pSFC has not been widely used in areas such as proteomics, where methods such as HPLC dominate. Packed column SFC has been extensively used in clinical and pharmaceutical laboratories, especially for separation of nonpolar and chiral drugs. This review will discuss recently published applications of pSFC, with a specific focus on its advantages and limitations for the analysis of pharmaceuticals with varying chemical properties.     

Characterization of military fog oil by comprehensive two-dimensional gas chromatography

The most commonly used military fog oil is characterized by comprehensive two-dimensional gas chromatography (GC×GC) coupled to either Flame Ionization Detection (FID) or Time-of-Flight Mass Spectrometric Detection (TOFMS) to advance the knowledge regarding the complete chemical makeup of this complex matrix. Two different GC×GC column sets were investigated, one employing a non-polar column combined with a shape selective column and the other an inverse column set (medium-polar/non-polar). The inverse set maximizes the use of the two-dimensional separation space and segregates aliphatic from aromatic fractions. The shape selective column best separates individual polycyclic aromatic hydrocarbons (PAHs) from the bulk oil. The results reveal that fog oil (FO) is composed mainly of aliphatic compounds ranging from C₁₀ to C₃₀, where naphthenes comprise the major fraction. Although many different species of aromatics are present, they constitute only a minor fraction in this oil, and no conjugated PAHs are found. The composition of chemically similar aliphatic constituents limits the analytical power of silica gel fractionation and GC–MS analysis to characterize FO. Among the aliphatic compounds identified are alkanes, cyclohexanes, hexahydroindanes, decalins, adamantanes, and bicyclohexane. The aromatic fraction is composed of alkylbenzene compounds, indanes, tetrahydronaphthalenes, partially hydrogenated PAHs, biphenyls, dibenzofurans and dibenzothiophenes. This work represents the best characterization of military fog oil to date. As the characterization process shows, information on such complex samples can only be parsed using a combination of sample preprocessing steps, multiple detection schemes, and an intelligent selection of column chemistries.     

High performance liquid chromatography of structural isomers using a cyclodextrin-poly(allylamine) coated silica column

Summary High performance liquid chromatography (HPLC) separation of substituted phenols by isocratic elution was investigated using a β-cyclodextrin-bonded column. The HPLC support was prepared in-house. This support was based on silica beads coated with a β-cyclodextrin-containing poly(allylamine). The retention behavior of some substituted phenol isomers and aromatic compounds was studied. The contribution of the amino groups of the polyamine and of the β-cyclodextrin cavity to the separation process is discussed. Two retention mechanisms, inclusion complex formation and acidbase interaction, were found. The effect of the composition and pH of the mobile phase on the separation was also examined.     

Procedure for and results of simultaneous determination of aromatic hydrocarbons and fatty acid methyl esters in diesel fuels by high performance liquid chromatography

The content of aromatic hydrocarbons in diesel fuels is regulated by appropriate standards, and a further reduction in the allowed concentration of these hazardous substances in these fuels is expected. The content of aromatic hydrocarbons in diesel fuels is most often determined using standard methods EN-12916 or ASTM D-6591. The content of polycyclic aromatic hydrocarbons (PAHs) is determined from a single peak obtained using normal phase high-performance liquid chromatography (NP-HPLC), a column of the NH2 type, n-heptane as the eluent, refractive index detector (RID) and backflushing of the eluent. However, the methods mentioned above cannot be applied when the fuel contains fatty acid methyl esters (FAME), which lately has become more common. The content of FAME in diesel oils is determined using mid-IR spectrophotometry based on the absorption of carbonyl group. However, no standard procedure for the determination of classes of aromatic hydrocarbons in diesel fuels containing FAME is yet available. The present work describes such a modification of methods EN-12916/ASTM D-6591 that provides a simultaneous determination of individual groups of aromatic hydrocarbons, total content of polycyclic aromatic hydrocarbons and the FAME content in diesel fuels. The refractive index detector (RID) and n-heptane as the mobile phase are still used, but backflushing of the eluent is applied after the elution of all polycyclic aromatic hydrocarbons. Additionally, ultraviolet diode array detection is used for the exact determination of low contents of polycyclic aromatic hydrocarbons and to confirm the presence of FAME in the analyzed fuel.     

High performance liquid chromatography of structural isomers using a cyclodextrin-poly(allylamine) coated silica column

Summary High performance liquid chromatography (HPLC) separation of substituted phenols by isocratic elution was investigated using a β-cyclodextrin-bonded column. The HPLC support was prepared in-house. This support was based on silica beads coated with a β-cyclodextrin-containing poly(allylamine). The retention behavior of some substituted phenol isomers and aromatic compounds was studied. The contribution of the amino groups of the polyamine and of the β-cyclodextrin cavity to the separation process is discussed. Two retention mechanisms, inclusion complex formation and acidbase interaction, were found. The effect of the composition and pH of the mobile phase on the separation was also examined.     

在线高效液相色谱-毛细管气相色谱联用方法的建立

建立了一种以保留间隙柱技术和阀切换以及定量管样品转移为接口并具有早期溶剂蒸气出口的在线液相色谱与毛细管气相色谱联用方法。考察了主要实验条件,如溶剂蒸发温度、载气压力等对联机系统性能的影响,并用萘和联苯对该系统的线性范围进行了测定。利用联机系统对一种轻柴油样品进行了分析。     

Application of bromoacetate‐substituted β‐CD‐bonded silica particles as chiral stationary phase for HPLC

Bromoacetate‐substituted [3‐(2‐O‐β‐cyclodextrin)‐2‐hydroxypropoxy]propylsilyl‐appended silica particles (BACD‐HPS), an important and useful synthetic intermediate for preparation of novel types of macrocycles‐capped β‐CD‐bonded silica particles including crown ether/cyclam/calix[4]arene‐capped β‐CD‐bonded silica particles, have been prepared and used as chiral stationary phase for HPLC. This synthetic stationary phase is characterized by means of elemental analysis. For the first time, the chromatographic behavior of BACD‐HPS was systematically evaluated with several disubstituted benzenes and some chiral drug compounds under both normal and RP conditions in HPLC. The results show that BACD‐HPS has excellent selectivity for the separation of aromatic positional isomers and chiral isomers of some drug compounds when used as stationary phase in HPLC.     

Investigation of π–π and ion–dipole interactions on 1-allyl-3-butylimidazolium ionic liquid-modified silica stationary phase in reversed-phase liquid chromatography

1-Allyl-3-butylimidazolium bromide ionic liquid [AyBIm]Br was prepared and used for the modification of mercaptopropyl-functionalized silica through surface radical chain-transfer addition. The obtained ionic liquid-modified silica (SiImBr) was characterized by elemental analysis, infrared spectroscopy, NMR spectroscopy, and thermogravimetric analysis. The selective retention behaviours of polycyclic aromatic hydrocarbons (PAHs) including some positional isomers were investigated using SiImBr as a stationary phase in reversed-phase liquid chromatography. The results showed that SiImBr presented multiple interactions including hydrophobic, π–π, and ion–dipole interactions during the separation of PAHs and dipolar compounds. However, it is proposed that π–π and ion–dipole interactions play important roles in the separation of PAHs and dipolar compounds. These results indicate that the ionic liquid-modified silica stationary phase is promising for future applications. A commercially available monomeric octadecylated silica (ODS) column and a custom-made poly(styrene)-grafted silica (Sil-St_n) column were used as references.     

Simple and sensitive method for determination of nitrated polycyclic aromatic hydrocarbons in diesel exhaust particles by gas chromatography-negative ion chemical ionisation tandem mass spectrometry

An extremely simple and sensitive method was developed for determination of nitrated polycyclic aromatic hydrocarbons (nitro-PAHs; mono-nitro-PAHs and dinitropyrenes) in diesel exhaust particles (DEPs) by gas chromatography-negative ion chemical ionisation tandem mass spectrometry (GC/NCI/MS/MS). We used two types of column in GC/NCI/MS/MS analysis. A polar column was used for determination of mono-nitro-PAHs, and a non-polar column was used for determination of dinitropyrenes and mono-nitro-PAHs except nitrofluoranthenes. The proposed method requires no clean-up procedure. The limits of detection ranged from 0.01 to 0.09 pg for all compounds tested. The applicability of the method to DEP samples was validated using diesel particulate standard reference materials (SRMs). Although DEPs contain complex matrices, all compounds could be detected easily in SRM2975 (diesel particulate matter) and SRM1975 (diesel particulate extract) without a clean-up procedure. The RSDs were less than 5% for all compounds examined. The quantitative results for SRMs exhibited good agreement with the available data in the literature. These results indicate that the proposed GC/NCI/MS/MS method is useful for determination of nitro-PAHs in DEP samples.     

The analysis of C4–C11 hydrocarbons in naphtha and reformate with a new apolar fused silica column

This paper deals with the separation of alkanes, naphthenes, and aromatic compounds in naphtha and reformate, on a newly developed apolar high resolution GC column. The selectivity of this apolar phase has been compared with those of squalane, DB-1, and SE-30. A total of 95 hydrocarbons were reliably identified, mostly by GC-MS. Repeated measurements of Kováts retention indices are presented as evidence for the reproducible manufacture of fused silica columns coated with this phase.     

Synthesis of penetrable macroporous silica spheres for high-performance liquid chromatography

Silica microspheres have been synthesized by phase separation and sol–gel transition coupled with emulsion method. The as-obtained material is characterized by scanning electron microscopy, nitrogen sorption, elemental analysis and particle size distribution measurements. The results demonstrated that the material featured with hierarchically porous structure, possessing both mesopores and penetrable macropores. The mesopores provide large surface area while the macropores traverse the silica particles, which may facilitate fast mass transfer as well as guarantee low backpressure when such materials are used for packed high-performance liquid chromatography (HPLC) column. Therefore, their preliminary applications as HPLC packings in fast separation and low-pressure separation have been attempted in the present study. Benzene, benzaldehyde and benzyl alcohol were separated within two minutes on the silica column at a flow rate of 7 mL min⁻¹. Vitamin E mixtures can also be baseline separated at a high flow rate of 8 mL min⁻¹. In addition, thirteen aromatic hydrocarbons were well separated on the octadecyl-bonded silica (ODS) column. In comparison with a commercial Kromasil ODS column, the pressure of the proposed column is much lower (<1/2) under the same chromatographic conditions, while comparable separation efficiency can be achieved.     

Ionic liquid‐bonded polysiloxane as stationary phase for capillary gas chromatography

Ionic liquid (IL) stationary phase is especially suitable for separation of complex samples, owing to the “dual nature” of IL. In this study, a synthetic method of ionic liquid‐bonded polysiloxane (PSOIL) as stationary phase of GC was proposed. Then, the PSOIL was used to prepare an 8 m capillary column by static method. The column efficiency was measured to be about 4000 plates/m (k=3.55, naphthalene) after the column had been conditioned at 210°C. The durability of PSOIL column was better than that of the mixed stationary phase of IL and OV‐1. Moreover, the Abraham solvation parameter model was employed to characterize the PSOIL. The result revealed that the PSOIL had stronger dispersion force (l) than neat IL and stronger hydrogen bond basicity (a) than DB‐1. That meant the PSOIL might offer good selectivity for both polar and non‐polar analytes. The column exhibited unique selectivity for various organic substances, such as the homologous compounds of alkanes, esters, alcohols and aromatic compounds. It was also found that some aromatic positional isomers could be separated better on the PSOIL column than on the DB‐1 column. Furthermore, the stationary phase was suitable for separation of high‐boiling point compounds such as polycyclic aromatic hydrocarbons, phthalic esters, etc. All of these demonstrated that the PSOIL offered good selectivity and high separation efficiency for a wide range of analytes.     

全二维气相色谱/飞行时间质谱用于柴油组成的研究

将全二维气相色谱法(GC×GC)用于柴油馏分的组成分布研究,建立了两种GC×GC方法,一种用于柴油组成的详细表征,另一种用于柴油族组成的快速分离和定量,两种方法均不需要样品预处理。用前一种方法对柴油馏分中的烃类化合物、主要的含硫化合物与含氮化合物组成进行了研究;对催化裂解柴油中的27种含氮化合物和42种含硫化合物进行了定性;用后一种方法在70 min内即可完成柴油馏分族组成的定量分析,应用所建立的方法测定了4个不同来源的柴油馏分中非芳烃、一环芳烃、二环芳烃、三环芳烃的含量,定量结果与ASTM D2425法