Preparation of a kind of mesoporous carbon and its performance in adsorptive desulfurization

Carbon materials were prepared using mesoporous silica HMS with different pore sizes as the hard templates and water-soluble phenolic resin as the carbon source. The obtained materials were characterized by powder X-ray diffraction, transmission electron microscopy and N₂ physical adsorption, and were used in adsorptive desulfurization. It has been shown that the carbon material prepared using HMS with larger pore size (>3 nm) presented uniform wormlike mesopore of 2.3 nm and large BET surface area (1903 m²/g). The mesoporous carbon was an excellent adsorbent to remove the refractory sulfur compound in diesel, especially dibenzothiophene and 4, 6-dimethyldibenzothiophene.     

有序中孔炭的电化学储氢性能

将蔗糖、聚环氧乙烯-聚环氧丙烯-聚环氧乙烯三嵌段共聚物和硅源构成的复合物进行预炭化、炭化和除硅处理合成出有序中孔炭, 采用XRD、TEM、HRTEM和N2吸脱附等手段对其进行表征, 并将有序中孔炭制成电极开展恒流充放电储氢性能研究. 结果显示, 具有较高比表面积(720 m2·g-1)和孔容(0.86 cm3·g-1)的有序中孔炭材料的电化学储氢容量为70.1 mAh·g-1, 高于具有相对较低比表面积(610 m2·g-1)和孔容(0.66 cm3·g-1)的有序中孔炭储氢容量(64.1 mAh·g-1). 通过与单壁碳纳米管电极(25.9 mAh·g-1)的对比, 表明有序中孔炭具有良好的电化学储氢性能和更高的电化学活性.     

Selective chemical vapor deposition synthesis of double-wall carbon nanotubes on mesoporous silica

Double-wall carbon nanotubes (DWNTs) have been selectively synthesized over Fe/Co loaded mesoporous silica by catalytic chemical vapor deposition of alcohol. Several silica materials with desired pore diameter and morphology have been investigated for the DWNT growth. The diameter distribution and selectivity of the DWNT are found to depend on the reaction temperature, pore size, and thermal stability of the support material. A high-yield synthesis of DWNTs has been achieved at 900 degrees C over high-temperature stable mesoporous silica. The outer diameter of DWNTs is found to be in the range of 1.5-5.4 nm with a "d" spacing of 0.38 +/- 0.02 nm between inner and outer layers, which is much larger than those of multiwall carbon nanotubes.     

Protein adsorption on the mesoporous molecular sieve silicate SBA-15: effects of pH and pore size

A mesoporous molecular sieve silicate, SBA-15, with three pore sizes (38.1 A, 77.3 A, and 240 A) has been synthesized using a non-ionic, tri-block copolymer as a template in a sol-gel method. The effects of synthesis conditions on the pore size and pore-size distribution of this adsorbent have been described. The adsorption of proteins on these crystalline, ordered, materials has been studied. The kinetics of adsorption and equilibrium capacity have been probed with three proteins of different dimensions. The effects of electrostatic interactions and protein size are illustrated. It has been shown that SBA-15 materials can be tailored to show size selectivity for proteins, and very high capacities (450 mg/g) can be obtained. Furthermore, the rates of adsorption are shown to be dependent on the pore size, protein structure and solution pH.     

Heterogeneous chiral Mn(III) salen catalysts for the epoxidation of unfunctionalized olefins immobilized on mesoporous materials with different pore sizes

Two chiral Mn(III) salen complexes were immobilized onto a series of mesoporous MCM-41 and MCM-48 materials with different pore sizes and the as-synthesized catalysts were active and enantioselective for the asymmetric epoxidation of styrene and indene. The results of XRD, FTIR, DR UV-vis, and N₂ sorption showed that the chiral Mn(III) salen complexes were anchored in the channels of mesoporous materials. The influence of organic silicane dosage on the catalytic performance was studied and the optimum dosage of organic silicane for preparing heterogeneous catalysts was determined. Furthermore, the effect of the fine-tuning of pore size on the performance of heterogeneous catalysts was discussed. In general, larger pore size of the supports could lead to higher conversions and the compatible pore size with substrate may be responsible for the improved enantiomeric excess (ee) values.     

密度泛函与分子模拟计算介孔孔径分布比较

用巨正则系综Monte Carlo模拟(GCMC)方法和密度泛函理论（ DFT）结合统计积分方程（SIE）计算了介孔材料的孔径分布.为比较这两种方法,以77 K氮气在介孔活性碳微球中的吸附数据为依据,求出其孔径分布.在GCMC模拟和DFT计算中,流体分子模型化为单点的Lerrnard-Jones球;流体分子与吸附剂材料之间的作用采用平均场理论中的10-4-3模型.在DFT方法中,自由能采用Tarazona 提出的加权近似密度泛函方法(weighted density approximation,WDA)求解.结果表明,对于孔径大于1.125 nm的介孔材料,GCMC和DFT两种方法都可以用来研究介孔材料的孔径分布;对于小于1.125 nm的介孔材料,不能用DFT方法计算孔径分布（DFT方法本身的近似产生了误差）,只能用分子模拟方法.     

超声波合成介孔分子筛

介孔分子筛MCM鄄41自问世以来一直是材料研究的热门领域之一[1,2],目前报道的主要合成方法有水热合成法[3,4]、微波法[5,6]等。其中水热法反应时间长达3~5d,耗能大,不利于实用化生产。超声波化学又称声化学,是一门新兴的交叉学科。超声波的波长远大于分子尺寸,因而不能对分子直     

Molecular-sieving capabilities of mesoporous carbon membranes

The size-sieving properties of a mesoporous carbon membrane were studied via molecular permeation and cyclic voltammetry experiments. Two phenomena, simple diffusion and electrochemically aided diffusion, were investigated. Molecular diffusion through the membrane was caused by a concentration gradient across the membrane and was facilitated by electrosorption of ions under an externally applied electric field. The diffusion of molecules transported through the membrane was characterized by the values of permeability and apparent diffusion coefficient in the membrane. Because larger molecules are more restricted in terms of penetrating the pores, the size-based selectivity of the mesoporous carbon membrane could be readily observed. For example, in the two-component permeation experiment, a high selectivity (alpha=56.9) of anilinium over Rhodamine B was found. It is inferred that the diffusive transport of the larger Rhodamine B molecules with a more extensive retardation comes from the competitive mechanism between the two kinds of molecules in accessing the pore. A series of voltammetric experiments involving a mesoporous carbon membrane immersed in various electrolytes with ions of different sizes allowed the observation of ion-exclusion phenomena. It was found that the size effect is significant for electrochemically aided diffusion and electrosorption processes. The number of cations inside the pores of the membrane decreases with increasing cation size. This phenomenon is due to the size-exclusion effect, which could be demonstrated by the values of electrical double-layer capacitance for sodium, magnesium, and tetrahexylammonium cations, at potentials ranging from negative values to the point of zero charge, corresponding to 86.7, 73.1, and 50.0 F/g, respectively. The findings of this work manifest that the relationship between the pore size and the dimensions of the molecules determines the transport and sorption behavior of nanoporous carbon materials.     

Prearation of Highly Ordered Mesoporous Silica Materials and Application as Enzeme Supports

An enzyme, horseradish peroxidase (HRP), was adsorbed in the manner of single immersion method on the silica mesoporous materials, FSM-16, MCM-41 and SBA-15 with various pore diameters from 27 to 92 and their enzymatic activity in an organic solvent and the thermal stability were studied. FSM-16 and MCM-41 showed larger amount of adsorption of HRP than SBA-15 or silica gel,when the pore sizes were larger than the spherical molecular diameter of HRP (ca 64×37). The increased enzyme adsorption capacity may be due to the surface characteristics of FSM-16 and MCM-41, which would be consistent with the observed larger adsorption capacity of cationic pigment compared with anionic pigment for these materials. The immobilized HRP on FSM-16 and MCM-41 with pore diameter above 50 showed the highest enzymatic activity in an organic toluene and thermal stability in aqueous solution at the temperature of 70℃. The immobilized enzymes on the other mesoporous materials including large or small pore sized FSM-16 showed lower enzymatic activity in an organic solvent and the thermal stability. Both surface character and size matching between pore sizes and the molecular diameters of HRP were important in achieving high enzymatic activity in organic solvent and high thermal stability.     

以介孔分子筛为金属催化剂载体制备纳米碳管

 以不同的介孔分子筛作为金属催化剂载体,对催化合成纳米碳管进行了系统的研究,讨论了反应条件对纳米碳管纯度和产量的影响. 结果表明,不同的介孔分子筛对金属活性中心的形成、碳组分的扩散、纳米碳管的管径及形态均有明显的影响. 此外,金属的种类、状态和含量也影响纳米碳管的合成. 探索了合成高产量纳米碳管的条件,并对介孔分子筛上生长纳米碳管的特点进行了讨论.     

Direct electrochemistry of myoglobin based on bicontinuous gyroidal mesoporous carbon matrix

A strategy of protein entrapment within the bicontinuous gyroidal mesoporous carbon (BGMC) matrix is demonstrated to probe the direct electrochemistry of myoglobin. Large surface area and remarkable electro-catalytic properties of BGMC make it a suitable candidate for high loading of protein molecules and the promotion of heterogeneous electron transfer (ET). In contrast with carbon nanotubes and general carbon mesoporous materials, BGMC is of a relatively isotropic graphited structure and thus can more effectively enhance the heterogeneous ET. Furthermore, a series of BGMCs with different pore sizes (2–7 nm) is designed and synthesized to study the influence of pore size on the immobilization of redox proteins and on the electron transfer.     

Functionalization of mesoporous carbon with superbasic MgO nanoparticles for the efficient synthesis of sulfinamides

Highly basic MgO nanoparticles with different sizes have been successfully immobilized over mesoporous carbon with different pore diameters by a simple wet-impregnation method. The prepared catalysts have been characterized by various sophisticated techniques, such as XRD, nitrogen adsorption, electron energy loss spectroscopy, high-resolution TEM, X-ray photoelectron spectroscopy, and the temperature-programmed desorption of CO(2). XRD results reveal that the mesostructure of the support is retained even after the huge loading of MgO nanoparticles inside the mesochannels of the support. It is also demonstrated that the particle size and dispersion of the MgO nanoparticles on the support can be finely controlled by the simple adjustment of the textural parameters of the supports. Among the support materials studied, mesoporous carbon with the largest pore diameter and large pore volume offered highly crystalline small-size cubic-phase MgO nanoparticles with a high dispersion. The basicity of the MgO-supported mesoporous carbons can also be controlled by simply changing the loading of the MgO and the pore diameter of the support. These materials have been employed as heterogeneous catalysts for the first time in the selective synthesis of sulfinamides. Among the catalysts investigated, the support with the large pore diameter and high loading of MgO showed the highest activity with an excellent yield of sulfinamides. The catalyst also showed much higher activity than the pristine MgO nanoparticles. The effects of the reaction parameters, including the solvents and reaction temperature, and textural parameters of the supports in the activity of the catalyst have also been demonstrated. Most importantly, the catalyst was found to be highly stable, showing excellent activity even after the third cycle of reaction.     

Carbon nanotubes as a support for Pt-and Pt-Ru-catalysts of reactions proceeding in fuel cells

Comparative study of two types of single-wall carbon nanotubes and standard carbon black Vulcan XC-72 as supports for catalysts of reactions proceeding in fuel cells is carried out. The nanotubes were prepared by arc method; they differed in the degree of their purifying from amorphous carbon and metal impurities. The structure and hydrophobic-hydrophilic properties of these carbon supports are studied by etalon porosimetry. The effect of the supports’ specific surface area on the deposited catalyst particles size and specific surface area is studied. The catalysts (Pt-Ru and Pt) were deposited from aqueous solutions of their salts. Platinum was also deposited by thermal decomposition of ethoxy clusters. It is shown that in methanol oxidation reaction at the Pt-Ru catalysts the current values per unit true surface area do not depend on the support nature, provided the catalyst loading is equal and the particle size is similar. When oxygen is reduced at platinum deposited onto purified nanotubes and the carbon black Vulcan XC-72, specific kinetic currents also are close to each other. It is shown that the degree of nanotubes purification and their structure affect the kinetics of this reaction significantly.     

Easy synthesis of iron doped ordered mesoporous carbon with tunable pore sizes

Precise control of the pore sizes for porous carbon materials is of importance to study the confinement effect of metal particles because the pore size in nanosize range will decide the physical and chemical properties of the metal nanoparticles.In this paper,we report a new approach for the synthesis of iron doped ordered mesoporous carbon materials with adjustable pore size using Fe-SBA-15 as hard template and boric acid as the pore expanding reagent.The pore size can be precisely adjusted by a step of 0.4 nm in the range of 3-6 nm.The carbonization temperature can be lowered to 773 K due to the catalytic role of the doped iron.The present approach is suitable for facile synthesis of metal imbedded porous carbon materials with tunable pore sizes.     

Catalytic properties of Ru nanoparticles embedded on ordered mesoporous carbon with different pore size in Fischer-Tropsch synthesis

A series of 3 wt% Ru embedded on ordered mesoporous carbon (OMC) catalysts with different pore sizes were prepared by autoreduction between ruthenium precursors and carbon sources at 1123 K. Ru nanoparticles were embedded on the carbon walls of OMC. Characterization technologies including power X-ray diffraction (XRD), nitrogen adsorption-desorption, transmission electron microscopy (TEM), and hydrogen temperature-programmed reduction (H₂-TPR) were used to scrutinize the catalysts. The catalyst activity for Fischer-Tropsch synthesis (FTS) was measured in a fixed bed reactor. It was revealed that 3 wt% Ru-OMC catalysts exhibited highly ordered mesoporous structure and large surface area. Compared with the catalysts with smaller pores, the catalysts with larger pores were inclined to form larger Ru particles. These 3 wt% Ru-OMC catalysts with different pore sizes were more stable than 3 wt% Ru/AC catalyst during the FTS reactions because Ru particles were embedded on the carbon walls, suppressing particles aggregation, movement and oxidation. The catalytic activity and C₅₊ selectivity were found to increase with the increasing pore size, however, CH₄ selectivity showed the opposite trend. These changes may be explained in terms of the special environment of the active Ru sites and the diffusion of products in the pores of the catalysts, suggesting that the activity and hydrocarbon selectivity are more dependent on the pore size of OMC than on the Ru particle size.     

不同碳源制备的介孔碳分子筛的性能研究

以介孔分子筛SBA-15为模板剂,分别采用蔗糖、糠醇和酚醛树脂作为碳源制备介孔碳分子筛.用TGA、XRD、N2吸附-脱附和TEM对制备的样品进行了表征和比较.结果表明,三种碳源制备的介孔碳分子筛的结构有序性明显不同.用蔗糖为碳源能够得到结构高度有序的介孔碳分子筛,其比表面积和孔容最大,分别为1 422 m2·g和1.15 cm3·g;用糠醇为碳源制备的样品次之;用普通酚醛树脂为碳源制备的样品其结构有序性最差.     

Syntheses of complex mesoporous silicas using mixtures of nonionic block copolymer surfactants: understanding formation of different structures using solubility parameters

The use of block copolymer (BCP) nonionic surfactant mixtures (including Pluronic, Brij and Tetronic types) as templates for synthesizing porous silica materials of mixed pore sizes is explored here. These systems have important applications because combinations of pore sizes can allow rapid access of reactants (via large pores) whilst providing the very high surface area of small pores for higher reaction rates or size selectivity. Examples of the materials prepared here include pore size bimodal hexagonal p6mm channel structures and cubic Im3m cage structures. It is shown here that the chemical similarity, as indicated by the solubility parameter, of the surfactants is an important factor in determining the pore structure and size distribution (PSD) of the pores. Monomodal pore structures are usually obtained when the solubility parameters of the surfactants are similar and bimodal pore structures when the solubility parameters are reasonably different. When the interaction parameter is very high disordered porous systems are formed. Ternary co-surfactant systems, e.g. P123-25R4-P65, can also yield highly ordered bimodal mesoporous silica with a hexagonal structure.     

Hβ/MCM-41复合分子筛催化剂上苯甲醚与乙酸酐酰化反应研究

以β沸石为硅源,制备了不同硅铝比的Hβ/MCM-41复合分子筛,考察了该复合分子筛对苯甲醚与乙酸酐酰化反应的催化效果,并与介孔MCM-41、微孔Hβ分子筛的催化效果进行了比较,研究了分子筛硅铝比、酸性及孔道结构对酰化反应催化性能的影响。结果表明,对于苯甲醚和乙酸酐酰化反应,Hβ/MCM-41复合分子筛具有较好的催化稳定性,反应过程中的积炭量较少,积炭的碳氢比较低。该复合分子筛不仅具有微孔沸石的强酸性,而且具有较大孔径的介孔,产物分子能及时从孔道中扩散出来,催化活性位不易中毒失活。     

Preparation and Characterization of Small Pore Carbon Molecular Sieves by Chemical Vapor Deposition of Pistachio Shells

Low-cost pistachio shells were used for the production of small pore carbon molecular sieves by the benzene deposition method. The prepared materials were characterized by the Brunauer–Emmett–Teller surface area and scanning electron microscopy. The deposition temperature and the deposition time parameters, which affect the formation of carbon molecular sieves, were examined. The effect of deposition temperature was examined in the range of 700–900°C, while deposition time was examined between 30 and 60?min. The optimum surface area of the carbon molecular sieve prepared by benzene deposition was 895?m²/g at 800°C. The average pore diameter of the carbon molecular sieve was 0.27?nm, principally denoted ultramicropore characteristics. The obtained values of the pore size distributions of the prepared carbon molecular sieves were in the range of 0.26–0.29?nm.     

纳米介孔分子筛MCM-41的微波辐射合成法

报导了纳米介孔分子筛MCM-41的微波辐射合成法,运用XRD、HRTEM、IR、TG、荧光光谱和低温N2吸附等技术对其进行了表征.研究结果表明,利用微波技术合成MCM-41,操作便利,节能省时.所得产物具有六方介孔排列结构,孔径约2.5 nm;颗粒大小分布均匀,平均粒径约40 nm;比表面积和孔隙率高,吸附量大,热稳定性好;在近紫外光激发下,显示出纳米粒子的量子发光效应.