负载Co介孔分子筛催化热解乙醇制备纳米碳管

以硅酸钠为原料,CTAB为模板剂,水热法合成MCM-41介孔分子筛,采用浸渍法制备负载钴的介孔分子筛(Co/MCM-41),并将其作为催化剂,CVD法热解无水乙醇制备CNTs.利用XRD、TEM、比表面积和孔径分布测定和Raman光谱等方法对所合成的介孔分子筛和纳米碳管进行了表征.结果表明:所制备的Co/MCM-41样品具有典型的MCM-41的介孔结构;当热解反应温度为750℃下所制备出的纳米碳管的品质最好.     

界面作用对PMMA/MCM-41/OMMT复合材料性能的影响

通过单体插层原位本体聚合的方法, 制备了多种不同含量的聚甲基丙烯酸甲酯(PMMA)/蒙脱土/介孔分子筛(无模板剂)复合材料. 研究了不同结构填料与基体间的界面作用, 以及不同结构填料的比例变化对复合材料性能的影响. 研究结果表明: 有机蒙脱土(OMMT)与介孔分子筛MCM-41(无模板剂)共同作为填料, 与基体发生较强的界面效应, 形成新型网络复合结构, 两种粒子起到了协同增强作用|当有机蒙脱土(OMMT)/介孔分子筛(MCM-41)混合填料(比例为1∶1)含量为0.5%时, PMMA基纳米复合材料的拉伸强度达到最大值49.0 MPa, 比PMMA提高了15%|同时添加OMMT和MCM-41的PMMA基纳米复合材料的热稳定性高于单独添加OMMT或MCM-41的PMMA基复合材料.     

纳米介孔分子筛MCM-41的微波辐射合成法

报导了纳米介孔分子筛MCM-41的微波辐射合成法,运用XRD、HRTEM、IR、TG、荧光光谱和低温N2吸附等技术对其进行了表征.研究结果表明,利用微波技术合成MCM-41,操作便利,节能省时.所得产物具有六方介孔排列结构,孔径约2.5 nm;颗粒大小分布均匀,平均粒径约40 nm;比表面积和孔隙率高,吸附量大,热稳定性好;在近紫外光激发下,显示出纳米粒子的量子发光效应.     

介孔分子筛MCM-41固载席夫碱与Cu(ClO_4)_2·6H_2O催化合成螺[吲哚-噻唑啉酮]衍生物

利用介孔分子筛纳米反应器MCM-41@席夫碱-Cu(ClO_4)_2·6H_2O作为非均相催化剂,简单高效地催化靛红-3-亚胺和巯基乙酸进行迈克尔加成-缩合反应,合成了一系列的螺[吲哚-噻唑啉酮]衍生物,收率最高可达99%.另外,发现具有相同官能团的非均相催化剂比均相催化剂表现出更好的催化效果,并进一步探索了介孔分子筛纳米反应器MCM-41孔道结构对该反应的影响.此类催化剂可回收再利用,催化循环6次后仍能得到93%的产率.     

基于介孔分子筛MCM-41“有机-无机”互穿结构纳米复合材料体系研究

采用硅烷偶联剂KH550对介孔分子筛MCM-41内、外表面进行改性,并利用氮气吸附-脱附,傅里叶红外光谱以及小角X衍射等进行表征,其结果显示KH550分子被引入MCM-41纳米孔道中,且—NH_2基团成功嫁接到MCM-41纳米颗粒表面.凝胶液相色谱实验结果证实本文中采用的双酚A型环氧树脂为低分子量环氧.随后,采用原位聚合的方法制备不同MCM-41含量环氧树脂纳米复合材料.最后,利用正电子湮没寿命谱测量复合材料自由体积孔洞;利用透射电镜,动态热机械分析和交流击穿对复合材料宏观性能进行研究.复合材料超薄切片TEM观察结果显示,在低MCM-41添加含量时,MCM-41颗粒可在复合材料中良好分散.同时,环氧分子在外施作用力和硅烷偶联剂功能作用下引入纳米孔道,形成"有机-无机"互穿结构复合材料体系,增强MCM-41和环氧树脂间相互作用力,在低MCM-41添加含量下提高复合材料玻璃化温度(15.1%↑)和击穿电压(22.6%↑).     

MCM-41介孔分子筛掺杂的微孔型聚合物电解质的制备与表征

以介孔分子筛MCM-41作填料,丙酮与二甲基甲酰胺混合液为溶剂,用直接造孔成膜的方法制备了微孔型聚合物电解质膜.该法避免使用造孔增塑剂,既简化了制膜工序,又减少电池中副反应的发生,使电池性能得以提高.MCM-41分子筛具有六方有序排列的单一柱状孔道结构和纳米级的粒子尺度,其骨架结构单元与一般聚合物电解质常用的纳米SiO2填料具有相同的化学成分,该分子筛堆积时形成的表面空隙及其独有的一维介孔孔道对聚合物电解质微孔的形成与连通、电导率的提高都具有重要作用,是一种极具实用价值的新型无机填料.     

具有强酸性位的高水热稳定介孔分子筛的合成

在强酸性介质中,以预先制备的β沸石纳米簇作为前驱体,通过S＋X－I＋路线及氨水热后处理步骤合成具有强酸性位的高水热稳定性介孔分子筛.XRD、氮气吸附、HRTEM和SEM分析表明所得样品具有普通MCM-41的典型介孔结构和表观形貌.较短的组装周期和室温的组装条件减弱了脱铝效应,27Al MAS NMR表明铝元素主要以四配位状态存在于介孔分子筛骨架中.采用NH3-TPD和水热老化方法分别考察了其固体酸性和水热稳定性,结果表明此介孔分子筛相对于普通MCM-41分子筛具有较强酸性位和较高的水热稳定性.沸石纳米簇的引入提高了分子筛骨架的聚合度和孔壁的厚度,是水热稳定性提高的主要原因.     

氯苄基官能化和氯苄基甲基双官能化介孔分子筛MCM-41的合成与表征

首先比较了氯苄三乙氧基硅烷和氯苄基三氯硅烷硅烷化介孔分子筛MCM-1的差异性,进而采用氯苄基三氯硅烷和甲基三氯硅烷混合试剂硅烷化介孔分子筛,一步得到氯苄基甲基双官能化介孔分子筛MCM-41,并用固体核磁予以证实.发现甲基三氯硅烷一方面可以作为一种“稀释剂”调节氯苄基的负载量,另一方面甲基的引入可增强介孔分子筛的水热稳定性.     

CMC和CTAB双模板法合成具有稳定结构的MCM-41中孔分子筛

以羧甲基纤维素和十六烷基三甲基溴化铵为双模板,制备出了具有更高稳定性并且具有高度有序二维六方结构的MCM-41介孔分子筛.透射电镜和X射线衍射结果表明,以双模板制备的MCM-41介孔分子筛具有高度有序的二维六方(p6mm)孔道结构.此外,以双模板制备的MCM-41介孔分子筛焙烧前后的X射线衍射结果表明,在焙烧过程中其晶胞收缩比例为3.1%.与以纯表面活性剂为模版制备的MCM-41介孔分子筛(晶胞收缩比例为9.7%)相比,双模板制备的MCM-41介孔分子筛具有更高的稳定性能. MCM-41介孔分子筛稳定性能的提高可能是由于在硅物种、表面活性剂以及羧甲基纤维素在自组装过程中,羧甲基纤维素表面丰富的羟基与硅物种Si-(OH)x的相互作用促进了Si-(OH)x的缩聚.     

含钴介孔分子筛催化热解乙醇制备纳米碳管

以CTAB为模板剂,硅酸钠、氯化钴为原料,通过水热法合成含钴介孔分子筛(Co-MCM-41)。以所合成的Co-MCM-41做催化剂,采用化学气相沉积(CVD)法催化热解乙醇制备纳米碳管。通过XRD、FT-IR、TEM、N2吸附-脱附和Raman光谱等分析手段对所合成的介孔分子筛和纳米碳管进行了表征。结果表明:合成的Co-MCM-41样品具有MCM-41的介孔结构,比表面积较大且介孔有序性较好。以所合成的含钴介孔分子筛催化热解乙醇制备出管径均匀、管壁较厚、顶端开口的多壁纳米碳管。     

高表面积MCM-41的合成与性能

通过易于控制的手段，合成出了超高表面积的MCM 41分子筛，并采用XRD、N2吸附脱附、热重 差热分析、SEM等测试手段对合成样品进行分析表征，主要考察了晶化时间对分子筛表面积的影响.其XRD结果表明,合成的固体产物具有六方排列的孔道结构，结晶度高.氮吸附脱附实验表明，产物具有单一的孔径分布，其BET表面积可达1300 m2•g－1左右，合成样品的平均孔径约3.2 nm，适宜的晶化时间是50～100 h.热重分析表明，样品热稳定性好，吡啶升温脱附曲线表明合成的样品具有弱酸性.     

MCM-41分子筛负载钼钴系催化剂的程序升温硫化研究

采用程序升温硫化（TPS）技术，研究了负载于MCM－41分子筛的钼钴系催化剂的性能，根据TPOS结果可知，（1）载体和MoO3相互作用的强度顺序如下：Al2O3＞Al2O3-MCM-41＞MCM－41＞TiO2－MCM－41，说明TiO2具有削弱MCM－41和MoO3作用的能力；而Al2O3则相反，它增加了MoO3和MCM－41的相互作用。（2）助剂CoO对负载于未经改性的MCM－41载体上的MoO3的硫化没有明显的促进作用，这和以Al2O3为载体的情况下不同，在Al2O3上，MoO3和CoO可能生成Co-Mo－O复合相，从而促进了MoO3的硫化。（3）助剂CoO对负载于经TiO2和Al2O3改性的MCM－41上的MoO3的硫化起了促进作用。     

Incorporation of CdS Nanoparticles Formed in Reverse Micelles into Mesoporous Silica

The incorporation of CdS nanoparticles, prepared in reverse micellar systems, into thiol-modified mesoporous silica, such as FM41 (functionalized MCM-41) and FM48 (functionalized MCM-48), has been investigated. The nanoparticles were immobilized in the mesopores via the incorporation of water droplets of the reverse micelles. A particle-sieving effect for FM41 having large (L-FM41, 3.8 nm) and medium (M-FM41, 3.6 nm) pore size was observed, in that the incorporation of the CdS nanoparticles was decreased with increasing particle size and with decreasing pore size of the FM41. Chemical vapor deposition treatment employed to narrow the mesopores of the CdS-FM41 enhanced the stability of CdS nanoparticles against heat treatment. The CdS-FM41 composites demonstrated photocatalytic activity for H(2) generation from 2-propanol aqueous solution, the better photocatalytic activity being obtained with the larger pore size for CdS-L-FM41. Copyright 2001 Academic Press.     

Biodegradable polyester/modified mesoporous silica composites for effective bone repair with self‐reinforced properties

A series novel composites based on poly(_L‐lactide) (PLLA) oligomer modified mesoporous silica (MCM41) homogeneous dispersed into poly(_L‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer has been successfully prepared. The structure of PLTG terpolymer was characterized by ¹H NMR. The structure and properties of modified and unmodified MCM41 were attested by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyzer (TGA), X‐ray diffraction (XRD), N₂ adsorption–desorption, scanning electron microscope (SEM), and transmission electron microscope (TEM), which demonstrated that the MCM41 was successfully grafted by the PLLA oligomer. The effect of different concentration of modified MCM41 in PLTG matrix on thermal properties, mechanical properties, and hydrophilicity was investigated by TGA, differential scanning calorimetry (DSC), mechanical testing, contact angle measurement, and SEM. The results of mechanical tests showed that 5 wt% of modified MCM41 nanoparticles gave rise to optimal reinforcing effect. The tensile strength, Young's modulus, and elongation at break of the PLTG/PLLA‐MCM41 (5%) composites were 33.2 Mpa, 1.58 Gpa, and 268.7%, respectively, which were all higher than the PLTG/MCM41 (5%) composites and pristine PLTG matrix, which were due to good interfacial adhesion between the PLTG matrix and MCM41 nanoparticles. TGA and DSC have shown that 5% modified MCM41 in the PLTG increased the temperature of composite degradation and T_g. Water contact angle measurement showed the hydrophilicity of the composites increases with the increase of modified MCM41 content. The live/dead assay showed that the modified MCM41 existing on the PLTG matrix presents very excellent cytocompatibility. Therefore, the novel composite material represents promising way for bone tissue engineering application.     

高岭土微球原位晶化合成高岭土-NaY-MCM-41复合物

在高岭土微球上原位晶化合成了高岭土-NaY-MCM-41复合物．利用XRD、SEM、TEM和BET等测试手段对合成的样品进行了表征．研究了高岭土表面原位生长NaY-MCM-41复合分子筛的合成化学．考察了合成体系的pH值、模板剂、H2O用量和SiO2／Al2O3比的影响．高岭土-NaY-MCM-41复合物具有大、介、微梯度分布的孔结构和合理的酸性分布．克服了单独的微孔分子筛孔径和介孔分子筛的局限性．实现了介孔、微孔分子筛的优势互补．     

Ketone Hydrogenation by Using ZnO−Cu(OH)Cl/MCM‐41 with a Splash of Water: An Environmentally Benign Approach

MCM‐41‐supported ZnO?Cu(OH)Cl nanoparticles were synthesized via an incipient wetness impregnation technique using zinc chloride and copper chloride salts as well as water at room temperature. The catalyst was characterized by powder X‐ray diffraction (PXRD), infrared spectroscopy (IR), and TGA, whereas surface and morphological studies were performed by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The above studies revealed the incorporation of metal species into the pores of MCM‐41, leading to a decrease in surface area of the nanoparticles that was found to be 239.079 m²/g. The substituents attached to the ketone determine the rate of the reaction, and the utilization of the green solvent ‘water’ astonishingly completes the hydrogenation reaction in 45 minutes at 40 °C with 100% conversion and 100% selectivity as analyzed by gas chromatography‐mass spectrometry. Hence, ZnO?Cu(OH)Cl/MCM‐41 nanoparticles with 2.46 wt% zinc and 6.39 wt% copper were demonstrated as an active catalyst for the reduction of ketones without using any gaseous hydrogen source making it highly efficient as well as environmentally and economically benign.     

Enzyme‐Responsive Intracellular‐Controlled Release Using Silica Mesoporous Nanoparticles Capped with ε‐Poly‐L‐lysine

The synthesis and characterization of two new capped silica mesoporous nanoparticles for controlled delivery purposes are described. Capped hybrid systems consist of MCM‐41 nanoparticles functionalized on the outer surface with polymer ε‐poly‐L ‐lysine by two different anchoring strategies. In both cases, nanoparticles were loaded with model dye molecule [Ru(bipy)₃]²⁺. An anchoring strategy involved the random formation of urea bonds by the treatment of propyl isocyanate‐functionalized MCM‐41 nanoparticles with the lysine amino groups located on the ε‐poly‐L ‐lysine backbone (solid Ru‐rLys‐S1 ). The second strategy involved a specific attachment through the carboxyl terminus of the polypeptide with azidopropyl‐functionalized MCM‐41 nanoparticles (solid Ru‐tLys‐S1 ). Once synthesized, both nanoparticles showed a nearly zero cargo release in water due to the coverage of the nanoparticle surface by polymer ε‐poly‐L ‐lysine. In contrast, a remarkable payload delivery was observed in the presence of proteases due to the hydrolysis of the polymer’s amide bonds. Once chemically characterized, studies of the viability and the lysosomal enzyme‐controlled release of the dye in intracellular media were carried out. Finally, the possibility of using these materials as drug‐delivery systems was tested by preparing the corresponding ε‐poly‐L ‐lysine capped mesoporous silica nanoparticles loaded with cytotoxic drug camptothecin (CPT), CPT‐rLys‐S1 and CPT‐tLys‐S1 . Cellular uptake and cell‐death induction were studied. The efficiency of both nanoparticles as new potential platforms for cancer treatment was demonstrated.     

Effect of polyether diamine on gas permeation properties of organic-inorganic hybrid membranes

The quantitative incorporation and high dispersion of platinum nanoparticles into MCM-41 has been carried out by the coordination between Pt(IV) ion and APTMS-anchored MCM-41. Before and after calcination of Pt/APTMS/MCM41 samples, the Pt content in samples was evaluated from home-made photoacoustic spectrometer (PAS). The PAS bands at 350 nm and 450 nm can be assigned to d–d transition bands of Pt complexes. By increasing the concentration of Pt solution, the PAS intensity of Pt/APTMS/MCM41 was increased proportionally up to 1.0×10⁻² M, and remained constant above 1.0×10⁻² M. It can be attributed to the saturation of Pt content within Pt/APTMS/MCM41. The Pt content in the saturated Pt/APTMS/MCM41 was 8.5 wt% (the theoretical value), 9.7 wt% (measured by EDX) and 9.2 wt% (measured by ESCA), respectively. This indicates that the content of Pt precursor within MCM-41 could be controlled by the concentration of Pt precursor solution. The PAS intensity of calcined Pt/APTMS/MCM41's in H₂ flow was increased up to 1.0×10⁻² M and remained nearly constant above 1.0×10⁻² M. Therefore, we suggest that the formation of Pt complexes with APTMS-anchored MCM-41 made it possible to incorporate quantitatively Pt nanoparticles in the range of 0.5–9.2 wt% within MCM-41 channels.     

Photocatalytic Synthesis of Composite CdSe/CdS Nanoparticles

We have shown that CdSe/CdS nanocomposites can be obtained in a photocatalytic reaction with participation of CdS nanoparticles from sodium selenosulfate. We have studied the kinetic characteristics of this process in detail and have shown that its most likely mechanism includes a step involving reaction between SeSO^3/2− anions and electrons generated in the conduction band of the CdS nanoparticles during irradiation and stabilized in traps on the semiconductor surface.__________Translated from Teoreticheskaya i Eksperimental’naya Khimiya, Vol. 41, No. 3, pp. 171–175, May–June, 2005.     

Synthesis and characterization of indium and thallium immobilized on isonicotinamide‐functionalized mesoporous MCM‐41: Two novel and highly active heterogeneous catalysts for selective oxidation of sulfides and thiols to their corresponding sulfoxides and disulfides

Two highly ordered isonicotinamide (INA)‐functionalized mesoporous MCM‐41 materials supporting indium and thallium (MCM‐41‐INA‐In and MCM‐41‐INA‐Tl) have been developed using a covalent grafting method. A surface functionalization method has been applied to prepare Cl‐modified mesoporous MCM‐41 material. Condensation of this Cl‐functionalized MCM‐41 with INA leads to the formation of MCM‐41‐INA. The reaction of MCM‐41‐INA with In(NO₃)₃ or Tl(NO₃)₃ leads to the formation of MCM‐41‐INA‐In and MCM‐41‐INA‐Tl catalysts. The resulting materials were characterized using various techniques. These MCM‐41‐INA‐In and MCM‐41‐INA‐Tl catalysts show excellent catalytic performance in the selective oxidation of sulfides and thiols to their corresponding sulfoxides and disulfides. Finally, it is found that the anchored indium and thallium do not leach out from the surface of the mesoporous catalysts during reaction and the catalysts can be reused for seven repeat reaction runs without considerable loss of catalytic performance.