Poly(methylene blue) functionalized graphene modified carbon ionic liquid electrode for the electrochemical detection of dopamine

An ionic liquid 1-butylpyridinium hexafluorophosphate based carbon ionic liquid electrode (CILE) was used as the substrate electrode and a poly(methylene blue) (PMB) functionalized graphene (GR) composite film was co-electrodeposited on CILE surface by cyclic voltammetry. The PMB–GR/CILE exhibited better electrochemical performances with higher conductivity and lower electron transfer resistance. Electrochemical behavior of dopamine (DA) was further investigated by cyclic voltammetry and a pair of well-defined redox peaks appeared with the peak-to-peak separation (ΔE_p) as 0.058 V in 0.1 mol L⁻¹ pH 6.0 phosphate buffer solution, which proved a fast quasi-reversible electron transfer process on the modified electrode. Electrochemical parameters of DA on PMB–GR/CILE were calculated with the electron transfer number as 1.83, the charge transfer coefficients as 0.70, the apparent heterogeneous electron transfer rate constant as 1.72 s⁻¹ and the diffusional coefficient (D) as 3.45 × 10⁻⁴ cm² s⁻¹, respectively. Under the optimal conditions with differential pulse voltammetric measurement, the linear relationship between the oxidation peak current of DA and its concentration was obtained in the range from 0.02 to 800.0 μmol L⁻¹ with the detection limit as 5.6 nmol L⁻¹ (3σ). The coexisting substances exhibited no interference and PMB–GR/CILE was applied to the detection of DA injection samples and human urine samples with satisfactory results.     

Electrochemical DNA Biosensor Based on Partially Reduced Graphene Oxide Modified Carbon Ionic Liquid Electrode for the Detection of Transgenic Soybean A2704‐12 Gene Sequence

In this work a partially reduced graphene oxide (p‐RGO) modified carbon ionic liquid electrode (CILE) was prepared as the platform to fabricate an electrochemical DNA sensor, which was used for the sensitive detection of target ssDNA sequence related to transgenic soybean A2704‐12 sequence. The CILE was fabricated by using 1‐butylpyridinium hexafluorophosphate as the binder and then p‐RGO was deposited on the surface of CILE by controlling the electroreduction conditions. NH₂ modified ssDNA probe sequences were immobilized on the electrode surface via covalent bonds between the unreduced oxygen groups on the p‐RGO surface and the amine group at the 5′‐end of ssDNA, which was denoted as ssDNA/p‐RGO/CILE and further used to hybridize with the target ssDNA sequence. Methylene blue (MB) was used as electrochemical indicator to monitor the DNA hybridization. The reduction peak current of MB after hybridization was proportional to the concentration of target A2704‐12 ssDNA sequences in the range from 1.0×10^?12 to 1.0×10^?6 mol/L with a detection limit of 2.9×10^?13 mol/L (3σ). The electrochemical DNA biosensor was further used for the detection of PCR products of transgenic soybean with satisfactory results.     

Nanostructured Hexacyanoferrate Intercalated Ni/Al Layered Double Hydroxide Modified Electrode as a Sensitive Electrochemical Sensor for Paracetamol Determination

An electrochemical sensor for paracetamol (PC) based on the hexacyanoferate(III) intercalated Ni−Al layered double hydroxide (Ni−Al−HCF) was presented. The as‐prepared LDH structurally and morphologically was characterized by scanning electron microscopy, X‐ray diffraction, and Fourier transform IR. Electrochemical studies revealed that Ni−Al−HCF film modified glassy carbon (GC) electrode exhibited remarkable electrocatalytic activity toward the oxidation of paracetamol. The electrochemical behavior of PC on the Ni−Al−HCF film was investigated in detail. Under optimum experimental conditions, the electrocatalytic response of the modified GC electrode was linear in the PC concentration range 3×10⁻⁶⁻–1.5×10⁻³ mol L⁻¹, with a detection limit of 8×10⁻⁷ mol L⁻¹ (S/N=3), using hydrodynamic amperometry. In addition, the modified electrode exhibited good reproducibility, long‐term stability and anti‐interference property. The fabricated sensor was successfully applied to determination of PC in various pharmaceutical preparations such as tablets, oral solution, and oral drops. Finally, the method was validated by the analysis of paracetamol spiked human serum samples, and good recoveries were obtained in the range of 99.2–103 %.     

Attapulgite with poly(methylene blue) composite film–Electrocatalytic determination of ascorbic acid

A conductive composite film consisted of natural nanostructure attapulgite (AT) with poly(methylene blue) (PMB) was constructed on glassy carbon (GC) electrode. The electrode exhibited an effective electrocatalytic activity towards the oxidation of ascorbic acid (AA) and well-defined oxidation peaks were observed in 0.1 M phosphate buffer solutions (PBS, pH 7.0) via cyclic voltammetry. Linear calibration plot was obtained over the range of 1.0 × 10⁻⁵ to 5.0 × 10⁻² M for ascorbic acid with the detection limit value of 1.0 × 10⁻⁶ M. The main interfering factor in biological samples was experimentally excluded. In addition, UV–Vis spectra were applied to reveal the formation of the nanocomposite film of PMB-AT.     

Carbon electrode modified with ionic liquid and multi-walled carbon nanotubes for voltammetric sensing of adenine

A voltammetric sensor was fabricated by applying a Nafion and multi-walled carbon nanotubes (MWCNTs) composite film on the surface of a carbon ionic liquid electrode (CILE), which was prepared by mixing 1-butyl-3-methylimidazolium hexafluorophosphate with graphite powder. The electrochemical behavior of adenine on the Nafion-MWCNTs/CILE was investigated in pH 5.5 buffer solution. Adenine showed an irreversible adsorption-controlled oxidation reaction with enhanced electrochemical response, which was due to the presence of high conductive MWCNTs on the CILE surface. The electrochemical parameters of adenine electro-oxidation were determined, and the experimental conditions were optimized. Under the optimal conditions, the oxidation peak current was linear to the adenine concentration over the range of 1.0?×?10^?7 to 7.0?×?10^?5 mol L^?1 with a detection limit of 3.3?×?10^?8 mol L^?1 (signal/noise?=?3). The electrode showed good stability and selectivity, and was further applied to milk powder samples with satisfactory results.     

Development of an Electrochemical Sensor Based on Covalent Molecular Imprinting for Selective Determination of Bisphenol‐A

In this study, an electrochemical sensor was developed and used for selective determination of bisfenol‐A (BPA) by integrating sol‐gel technique and multi‐walled carbon nanotubes (MWCNTs) modified paste electrode. BPA bounded by covalently to isocyanatopropyl‐triethoxy silane (ICPTS) was synthesized as a new precursor (BPA‐ICPTS) and then BPA‐imprinted polymer (BPA‐IP) sol‐gel was prepared by using tetramethoxysilane (TMOS) and BPA‐ICPTS. Non‐imprinted polymer (NIP) sol‐gel was obtained by using TMOS and (3‐Aminopropyl) triethoxysilane. Both BPA‐IP and NIP sol‐gels were characterized by nitrogen adsorption‐desorption analysis, FTIR, SEM, particle size analyzer and optical microscope. Carbon paste sensor electrode was fabricated by mixing the newly synthesized BPA‐IP with MWCNTs, graphite powder and paraffin oil. The electrochemical characterization of the sensor electrode was achieved with cyclic and differential pulse voltammetric techniques. The response of the developed sensor under the most proper conditions was linear in BPA concentration range from 4.0×10⁻⁹ to 1.0×10⁻⁷ mol L⁻¹ and 5.0×10⁻⁷ to 5.0×10⁻⁵ mol L⁻¹ and the detection limit was 4.4×10⁻⁹ mol L⁻¹. The results unclosed that the proposed sensor displayed high sensitivity and selectivity, superior electrochemical performance and rapid response to BPA.     

Selective Electroanalysis of Ascorbic Acid Using a Nickel Hexacyanoferrate and Poly(3,4‐ethylenedioxythiophene) Hybrid Film Modified Electrode

The mixed‐valent nickel hexacyanoferrate (NiHCF) and poly(3,4‐ethylenedioxythiophene) (PEDOT) hybrid film (NiHCF‐PEDOT) was prepared on a glassy carbon electrode (GCE) by multiple scan cyclic voltammetry. The films were characterized using atomic force microscopy, field emission scanning electron microscopy, energy dispersive spectroscopy, X‐ray diffraction, and electrochemical impedance spectroscopy (AC impedance). The advantages of these films were demonstrated for the detection of ascorbic acid (AA) using cyclic voltammetry and amperometric techniques. The electrocatalytic oxidation of AA at different electrode surfaces, such as the bare GCE, the NiHCF/GCE, and the NiHCF‐PEDOT/GCE modified electrodes, was determined in phosphate buffer solution (pH 7). The AA electrochemical sensor exhibited a linear response from 5×10⁻⁶ to 1.5×10⁻⁴ M (R²=0.9973) and from 1.55×10⁻⁴ to 3×10⁻⁴ M (R²=0.9983), detection limit=1×10⁻⁶ M, with a fast response time (3 s) for AA determination. In addition, the NiHCF‐PEDOT/GCE was advantageous in terms of its simple preparation, specificity, stability and reproducibility.     

Direct Electrochemistry of Myoglobin in a Nafion‐Ionic Liquid Composite Film Modified Carbon Ionic Liquid Electrode

In this paper two kinds of ionic liquids (ILs) were used for the construction of a myoglobin (Mb) electrochemical biosensor. Firstly a hydrophilic ionic liquid of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) was used as binder to prepare a carbon ionic liquid electrode (CILE), then a Nafion and hydrophobic ionic liquid of 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) composite film was applied on the surface of the CILE. The direct electrochemistry of Mb in the Nafion‐BMIMPF₆/CILE was achieved with the cathodic and anodic peak potentials located at ?0.345 V and ?0.213 V (vs. SCE). The formal potential (E°′) was located at ?0.279 V, which was the characteristic of Mb Fe^III/Fe^II redox couples. The electrochemical behaviors of Mb in the Nafion‐ionic liquid composite film modified CILE were carefully investigated. The Mb modified electrode showed good electrocatalytic behaviors to the reduction of trichloroacetic acid (TCA) and NaNO₂. Based on the Nafion‐BMIMPF₆/Mb/CILE, a new third generation reagentless biosensor was constructed.     

Electrochemical DNA Biosensor Based on Graphene and TiO2 Nanorods Composite Film for the Detection of Transgenic Soybean Gene Sequence of MON89788

Based on graphene (GR), TiO₂ nanorods, and chitosan (CTS) nanocomposite modified carbon ionic liquid electrode (CILE) as substrate electrode, a new electrochemical DNA biosensor was effectively fabricated for the detection of the transgenic soybean sequence of MON89788. By using methylene blue (MB) as hybridization indicator for monitoring the hybridization with different ssDNA sequences, the differential pulse voltammetric response of MB on DNA modified electrodes were recorded and compared. Due to the synergistic effects of TiO₂ nanorods and GR on the electrode surface, the electrochemical responses of MB were greatly increased. Under optimal conditions the differential pulse voltammetric response of the target ssDNA sequence could be detected in the range from 1.0×10^?12 to 1.0×10^?6 mol/L with a detection limit of 7.21×10^?13 mol/L (3σ). This electrochemical DNA biosensor was further applied to the polymerase chain reaction (PCR) product of transgenic soybeans with satisfactory results.     

Comparative Study on Electroanalysis of Fenthion Using Silver Amalgam Film Electrode and Glassy Carbon Electrode Modified with Reduced Graphene Oxide

Oxidation and reduction processes of the insecticide fenthion was comparatively investigated at a reduced graphene oxide modified glassy carbon electrode (RGO‐GCE) and a cyclic renewable silver amalgam film electrode (Hg(Ag)FE) using square wave stripping voltammetry (SWSV). The influence of pH and SW parameters was investigated. The linear concentration ranges were found to be 1 × 10⁻⁶ – 2 × 10⁻⁵ and 1 × 10⁻⁷ – 2 × 10⁻⁵ mol L⁻¹ for Hg(Ag)FE and RGO‐GCE, respectively. The detection and quantification limits were calculated as 1.3 × 10⁻⁷ and 4.5 × 10⁻⁷ mol L⁻¹ for Hg(Ag)FE and 7.6 × 10⁻⁹ and 2.5 × 10⁻⁸ mol L⁻¹ for RGO‐GCE. Both of the developed electroanalytical methods offer rapid and simple detection of fenthion and were used on spiked tap and river water and apple juice samples. Scanning electron microscopy was used for RGO‐GCE surface characterization.     

Square Wave‐Anodic Stripping Voltammetric Determination of Copper at a Bismuth Film/Glassy Carbon Electrode Using 3‐[(2‐Mercapto‐Vinyl)‐Hydrazono]‐ 1,3‐Dihydro‐Indol‐2‐One

This study reports a highly sensitive electrochemical sensor based on Bi film modified glassy carbon electrode (BiF/GCE) for total determination and speciation trace concentrations of copper(II) ions in environmental water samples. Square wave‐adsorptive anodic stripping voltammetric (SW‐ASV) experiment was performed for monitoring selective accumulation of copper(II) with reagent 3‐[(2‐mercapto‐vinyl)‐hydrazono]‐1,3‐dihydro‐indol‐2‐one (MHDI) at pH 9–10. The mechanism of the electrode reaction of Cu²⁺‐MHDI complex was safely assigned. The sensor exhibited a wide linear range (3.22×10⁻⁹–2.0×10⁻⁷ mol L⁻¹) with lower limits of detection (LOD) and quantitation (LOQ) of 9.6×1⁻¹⁰ and 3.22×10⁻⁹ mol L⁻¹, respectively (R²=0.9993). The proposed sensor exhibited interference from active metal ions e. g. Cd, Hg. The performance of the proposed method was compared successfully with most of the reported methods and comparable efficiencies were obtained. The analytical utility of the proposed SW‐ASV method has been successfully validated for trace analysis of copper(II) in environmental water samples. The method offers a precise, accurate approach with good reproducibility, robustness, ruggedness, and cost effectiveness.     

Square Wave Voltammetry for Selective Detection of Dopamine Using Polyglycine Modified Carbon Ionic Liquid Electrode

The electrochemical polymerization of glycine on carbon ionic liquid electrode (CILE) was described. The presence of ionic liquid on the surface of CILE facilitated the electropolymerization of glycine. The polyglycine modified CILE provided a valid and simple approach to selectively detect dopamine in the presence of AA in physiological environment. The proposed sensor not only decreased the voltammetric responses of AA but also dramatically enhanced the oxidation peak current of DA compared to bare CILE. Using square wave voltammetry, the modified CILE showed good electrochemical behavior to DA, a linear range of 1.0×10^?7–3.0×10^?4 M in the presence of 1 mM ascorbic acid (AA) and a detection limit of 5.0×10^?9 M was estimated (S/N=3).     

Electrodeposition CaCO3 Nanoparticles‐chitosan Composite Film on Carbon Ionic Liquid Electrode as a Platform for Hemoglobin Electrochemical Biosensor

By one‐step co‐electrodeposition CaCO₃ nanoparticles‐chitosan composite film on carbon ionic liquid electrode (CILE), and then by spreading the composition of hemoglobin (Hb) and chitosan on the nanoCaCO₃‐chi/CILE, a Hb‐chi/nanoCaCO₃‐chi/CILE was fabricated and the direct electrochemistry and electrocatalysis of Hb at the electrode was investigated. The electrochemical impedance spectroscopy of the modified electrode showed the electron transfer resistance was 1166 Ω. Investigation results of cyclic voltammetrys showed a pair of well‐defined and quasireversible redox peak of Hb with the formal potentials of ‐0.295 V (vs. SCE) in 0.1 mol·L^‐1 pH 7.0 PBS; the response time of the reduction peak currents of Hb was lower than 3s; a linear range for determination of H₂O₂ was from 5.0 μmol·L^‐1 to 1.3 mmol·L^‐1 with a detection limit of 1.6 μmol·L^‐1 (S/N = 3) and a sensitivity of 0.16 A·M^‐1·cm^‐2; the electron transfer rate constant and the apparent Michaelis‐Menten constant of Hb were 1.98 s^‐1 and 0.81 mmol·L^‐1, respectively. As a result, the case of the one‐step co‐electrodeposition and the promising feature of biocomposite could serve as a versatile platform for the fabrication of electrochemical biosensors.     

A Green Approach to the Synthesis of Well‐structured Prussian Blue Cubes for the Effective Electrocatalytic Reduction of Antiprotozoal Agent Coccidiostat Nicarbazin

For the first time, a robust electrochemical sensor to detect the coccidiostat nicarbazin (NCZ) is developed through the green synthesis of Prussian blue cubes from Volvariella volvacea (paddy straw mushroom) extract. Recently, numerous articles were reported about the issue that the prophylactic drugs were injected excessively as a feed additive for fattening the chickens in short period. It is a significant concern that the level of coccidiostat NCZ exceeds the residue limits in the tissues of the meat; mainly, in chicken and eggs. Therefore, it is crucial to develop a sensitive, reproducible and long‐lasting sensor for the real‐time detection of NCZ. Thus, we have generated an electrochemical sensor through the economic screen‐printed carbon electrode (SPCE) modification method. Eco‐friendly Prussian blue cubes are fabricated on the carbon film of SPCE. As a result, the modified electrode showed exceptional electrocatalytic ability towards NCZ and the reduction peak currents are correlated to the concentrations of NCZ. It retains the more extensive working range between 1.25×10⁻⁷ to 1.53×10⁻³ mol L⁻¹, and it possesses a very low limit of detection as well as the appreciable sensitivity. This method is successfully applied to the recognition of NCZ in the samples of chicken meat and eggs.     

A sensitive electrochemical sensor for detection of rutin based on a gold nanocage‐modified electrode

In this article, an electrochemical sensor based on a gold nanocage (AuNC)‐modified carbon ionic liquid electrode (CILE) was fabricated and applied to the sensitive rutin determination. The presence of AuNCs on the electrode surface greatly improved the electrochemical performance of the working electrode due to its specific microstructure and high metal conductivity. Electrochemical behavior of rutin on AuNCs/CILE was studied using cyclic voltammetry and differential pulse voltammetry with the related electrochemical parameters calculated. Under the optimal experimental conditions, the oxidation peak current of rutin and its concentration had good linear relationship in the range from 4.0 × 10^?9 to 7.0 × 10^?4 mol/L with a low detection limit of 1.33 × 10^?9 mol/L (3σ). This fabricated AuNCs/CILE was applied to direct detection of the rutin concentration in drug samples with satisfactory results, showing the real application of AuNCs in the field of chemically modified electrodes.     

Direct electrochemistry and electrocatalysis of hemoglobin in sodium alginate film on a BMIMPF6 modified carbon paste electrode

A room temperature ionic liquid (RTIL) modified carbon paste electrode was constructed based on the substitute of paraffin with 1-butyl-3-methyl-imidazolium hexafluorophosphate (BMIMPF₆) as binder for carbon paste. Direct electrochemistry and electrocatalytic behaviors of hemoglobin (Hb) entrapped in the sodium alginate (SA) hydrogel film on the surface of this carbon ionic liquid electrode (CILE) were investigated. The presence of IL in the CILE increased the electron transfer rate and provided a biocompatible interface. Hb remained its bioactivity on the surface of CILE and the SA/Hb modified electrode showed a pair of well-defined, quasi-reversible cyclic voltammetric peaks with the apparent standard potential (E^0′) at about −0.344 V (vs. SCE) in pH 7.0 Britton–Robinson (B–R) buffer solution, which was attributed to the Hb Fe(III)/Fe(II) redox couple. UV–Vis absorption spectra indicated that heme microenvironment of Hb in SA film was similar to its native status. Hb showed a thin-layer electrochemical behavior in the SA film with the direct electron transfer achieved on CILE without the help of electron mediator. Electrochemical investigation indicated that Hb took place one proton with one electron electrode process and the average surface coverage of Hb in the SA film was 3.2 × 10⁻¹⁰ mol/cm². The immobilized Hb showed excellent electrocatalytic responses to the reduction of H₂O₂ and nitrite.     

Electrochemical aptamer sensor for highly sensitive detection of mercury ion with Au/Pt@carbon nanofiber‐modified electrode

In this paper, an electrochemical aptamer sensor was proposed for the highly sensitive detection of mercury ion (Hg²⁺). Carbon nanofiber (CNF) was prepared by electrospinning and high‐temperature carbonization, which was used for the loading of platinum nanoparticles (PtNPs) by the hydrothermal method. The Pt@CNF nanocomposite was modified on the surface of carbon ionic liquid electrode (CILE) to obtain Pt@CNF/CILE, which was further decorated by gold nanoparticles (AuNPs) through electrodeposition to get Au/Pt@CNF/CILE. Self‐assembling of the thiol‐based aptamer was further realized by the formation of Au‐S bond to get an electrochemical aptamer sensor (Aptamer/Au/Pt@CNF/CILE). Due to the specific binding of aptamer probe to Hg²⁺ with the formation of T‐Hg²⁺‐T structure, a highly sensitive quantitative detection of Hg²⁺ could be achieved by recording the changes of current signal after reacting with Hg²⁺ within the concentration range from 1.0 × 10^?15 mol/L to 1.0 × 10^?6 mol/L and the detection limit of 3.33 × 10^?16 mol/L (3σ). Real water samples were successfully analyzed by this method.     

Nickel determination in osteoblast-like cell culture medium by adsorptive cathodic stripping voltammetry with a mercury microelectrode

The purpose of this study is to investigate the influence of nickel, which is an alloying element in commonly used metallic biomaterials, on the biomaterials mineralization process. An electrochemical method was developed to quantify this metal ion in osteoblast-like cell culture medium (OST) by performing adsorptive cathodic stripping voltammetry (CSV) with dimethylglyoxime (DMG) at a mercury film microelectrode (MFM). The optimized analytical conditions and the square-wave CSV parameters for the analysis are: DMG concentration: 5.00 × 10⁻⁴ mol L⁻¹; ammonium chloride buffer: 0.10 mol L⁻¹ (pH 9.2); frequency: 50 Hz, amplitude 20 mV; step: 2 mV; adsorption time: 10 s, deposition potential: −0.70 V and reduction potential: −1.20 V. The limit of detection was 7.70 × 10⁻⁹ mol L⁻¹ for an adsorption time of 10 s. The results achieved by CSV using the MFM were compared to those obtained by atomic absorption spectrometry (AAS) to ensure the reliability of the electrochemical method. The mineralization process was evaluated by biochemical and histochemical assays.     

Electropolymerization of Acid Chrome Blue K on Glassy Carbon Electrode for the Determination of Curcumin

Acid chrome blue K (ACBK) was electropolymerized on the surface of a glassy carbon electrode (GCE) by cyclic voltammetric sweep in the potential range from –0.2 to 0.9 V. The characteristic of poly‐ACBK film was studied by different methods such as electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. This modified electrode showed excellent electrocatalytic response to curcumin with the increase of the electrochemical responses. Under the optimal conditions a good linear voltammetric response could be obtained over the range of 1.0 × 10^?7‐7.0 × 10^?5 M and the detection limit was got as 4.1 × 10^?8 M (S/N = 3). The method was successfully applied for the determination of curcumin in human urinev samples.     

Sensitive Voltammetric Determination of Methyl Parathion Using a Carbon Paste Electrode Modified with Mesoporous Zirconia

A mesoporous zirconia modified carbon paste electrode was developed for electrochemical investigations of methyl parathion (MP, Phen‐NO₂). The significant increase of the peak currents and the improvement of the redox peak potential indicate that mesoporous zirconia facilitates the electronic transfer of MP. The oxidation peak current was proportional to the MP concentration in the range from 1.0×10⁻⁸ to 1.0×10⁻⁵ mol L⁻¹ with a detection limit of 4.6×10⁻⁹ mol L⁻¹ (S/N=3) after accumulation under open‐circuit for 210 s. The proposed method was successfully applied to the determination of MP in apple samples.