Interfacial effect on confined crystallization of poly(ethylene oxide)/silica composites

The impact of nanoconfinement introduced by nanoparticles on polymer crystallization has attracted extensive attention because it plays an important role in the ultimate properties of polymer nanocomposites. In this study, interfacial and spatial confinement effects of silica (SiO₂) nanoparticles on the crystallization behaviors of poly(ethylene oxide) (PEO)/SiO₂ composites were systematically investigated by changing the size and concentration of SiO₂ in PEO matrix. The composites with high silica loadings exhibit two crystallization peaks of PEO as determined by differential scanning calorimetry. The first peak at 7–43 °C is related to the bulk PEO, while the second peak at ?20 to ?30 °C is attributed to the restricted PEO segments. Three‐layer (amorphous, interfacial, and bulk) model is proposed to interpret the confined crystallization of PEO/SiO₂ composites, which is supported by the results of thermogravimetric analysis and solid‐state ¹H nuclear magnetic resonance. In amorphous layer, most PEO segments are directly adsorbed on SiO₂ surface via hydrogen bonding. The interfacial PEO layer, which is nonuniform, is composed of crystallizable loops and tails extending from amorphous layer. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 414–423     

Confined crystallization behaviors in polyethylene/silica nanocomposites: Synergetic effects of interfacial interactions and filler network

The confinement effects introduced by nanoparticles have been reported to influence the phase behaviors thus the properties of polymer nanocomposites. In this study, molecular dynamics and crystallization behaviors of polyethylene (PE) composited with three types of silica (SiO₂) nanoparticles, namely unmodified SiO₂, hydrophobically modified SiO₂, SiO₂‐APTES (3‐aminopropyltriethoxysilane) and SiO₂‐PTES (n‐propyltriethoxysilane), were systematically investigated via a combination of DSC, XRD and ¹H solid‐state NMR measurements. The suppressions in crystallization and chain mobilities of PE rank in the order of unmodified SiO₂ < SiO₂‐APTES < SiO₂‐PTES due to the increasing interfacial interactions between PE and SiO₂ nanoparticles. Additionally, independent of polymer–nanoparticle interactions, a silica network forms for all three kinds of nanocomposites when SiO₂ content reaches 83 wt %. The mobilities of polymer chains are severely restricted by such a percolated network structure, leading to a turning point in the crystallization ability of nanocomposites and a new crystallization peak at 45 °C lower than that of pure PE. The synergetic effects of interfacial interactions and filler network on polymer crystallization have been thoroughly studied in this work, which will provide guidance on modifying and designing nanocomposites with controlled properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 498–505     

Role of adsorbed chain rigidity in reinforcement of polymer nanocomposites

The thermomechanical behavior of polymer nanocomposites is mostly governed by interfacial properties which rely on particle–polymer interactions, particle loading, and dispersion state. We recently showed that poly(methyl methacrylate) (PMMA) adsorbed nanoparticles in poly(ethylene oxide) (PEO) matrices displayed an unusual thermal stiffening response. The molecular origin of this unique stiffening behavior resulted from the enhanced PEO mobility within glassy PMMA chains adsorbed on nanoparticles. In addition, dynamic asymmetry and chemical heterogeneities existing in the interfacial layers around particles were shown to improve the reinforcement of composites as a result of good interchain mixing. Here, the role of chain rigidity in this interfacially controlled reinforcement in PEO composites is investigated. We show that particles adsorbed with less rigid polymers improve the mechanical properties of composites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 9–14     

Synthesis of polyethylene oxide graft polysilylenes and networks based on poly(di‐n‐pentylsilylene/n‐pentyloct‐7‐enyl) copolymers

Poly(dipentylsilylene) copolymers containing n‐pentyl‐n‐oct‐7‐enylsilane units were prepared by reductive coupling of the corresponding dichlorosilanes. Linear high molecular weight and some crosslinked polymer were obtained. The soluble products exhibited optical and thermal properties like poly(dipentylsilylene). Differential scanning calorimetry was used to investigate crystallization and to monitor thermal crosslinking. Vinyl functionalized side chains were hydrosilylated with dipentylsilane and dimethylchlorosilane and crosslinked via the side chains. Hydrosilylation with di‐n‐pentyl(trimethylsiloxypropyl)silane led to a partial hydroxy functionalization of the polysilylene and enabled anionic PEO grafting of the poly(dipentylsilylene). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2306–2318, 2000     

The influence of variant PE‐b‐PEO segments on physical properties of LLDPE graft copolymers

A method was adopted to fix a series of polymers of PE‐b‐PEO with different PEO/PE segments on the chains of LLDPE. Maleic anhydride (MA) reacting with hydroxyl group of PE‐b‐PEO (mPE‐b‐PEO) was used as the intermediate. The structures of intermediates and graft copolymers were approved by ¹H NMR and FTIR. XPS analysis revealed a great amount of oxygen on the surface of grafted copolymers although the end group of PEO was fixed on the LLDPE chains through MA. Thermal properties of the graft copolymers as determined by differential scanning calorimetry (DSC) showed that PE segments in the grafted monomers could promote the heterogeneous nucleation of the polymer, increase T_c, and crystal growth rate. While the amorphous PEO segments which attached to the crystalline PE segments in LLDPE, impaired their ability to fit the crystal lattice, and depressed the crystallization of LLDPE backbones. In this study, it was also verified through the dynamic rheological data that increasing M_n of grafted monomers significantly increased the complex viscosity and enhanced the shear‐thinning behavior. Long‐branched chains formed by grafted monomers enhanced the complex moduli (G′ and G″) value and retarded relaxation rate. However, there were little influence on the rheological properties when increasing the amounts of PEO segments (or decreasing PE segments) of grafted monomers with similar molecular weight. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 506–515, 2008     

Rheological behavior of fumed silica filled polyethylene oxide

Influence of molecular weight of polymer matrix on nanocomposites rheology is not yet well understood. Herein dynamic rheological responses of fumed silica (FS)/polyethylene oxide (PEO) nanocomposites are investigated as a function of viscosity‐averaged molecular weight (M_η) of PEO, volume fraction (?) and surface characteristics (hydrophilic or hydrophobic) of FS. In the nanocomposites, FS does not influence the glass transition and crystallinity of PEO in the mobile PEO phase while the interfacial interactions tend to immobilize a small fraction of PEO chains that could not undergo glass transition. In spite of the common observation that the reinforcement decreases with increasing M_η of PEO and improving hydrophobicity of FS, linear rheological responses are well reproduced by the two‐phase model, revealing the crucial contribution of the non‐Newtonian matrix undergoing microscopic strain amplified by the filler. Furthermore, nonlinear rheological responses of the nanocomposites are collapsed into master curves plotted against local strain of the matrix. Analyzing the nonlinear rheology by Fourier transform and stress waveform methods reveal the dominating contribution of the matrix and the role of strain amplification played by the filler. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 397–405     

Synthesis and characterization of crystalline graft polymer poly(ethylene oxide)‐g‐poly(ɛ‐caprolactone)2 with modulated grafting sites

The graft polymer poly(ethylene oxide)‐g‐poly(?‐caprolactone)₂ (PEO‐g‐PCL₂) with modulated grafting sites was synthesized by the combination of ring‐opening polymerization (ROP) mechanism, efficient Williamson reaction, with thiol–ene addition reaction. First, the precursor of PEO‐Allyl‐PEO with two terminal hydroxyl groups and one middle allyl group was prepared by ROP of EO monomers. Then, the macroinitiator [PEO‐(OH)₂‐PEO]_s was synthesized by sequential Williamson reaction between terminal hydroxyl groups and thiol–ene addition reaction on pendant allyl groups. Finally, the graft polymer PEO‐g‐PCL₂ was obtained by ROP of ?‐CL monomers using [PEO‐(OH)₂‐PEO]_s as macroinitiator. The target graft polymer and all intermediates were well characterized by the measurements of gel permeation chromatography, ¹H NMR, and thermal gravimetric analysis. The crystallization behavior was investigated by the measurements of differential scanning calorimetry, wide‐angle X‐ray diffraction and polarized optical microscope. The results showed that when the PCL content of side chains reached 59.2%, the crystalline structure had been dominated by PCL part and the crystalline structure formed by PEO part can be almost neglected. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2239–2247     

Amphiphilic silicones prepared from branched PEO‐silanes with siloxane tethers

Amphiphilic silicones were prepared by the covalent incorporation of branched polyethylene oxide (PEO) via a siloxane tether. This was achieved by using six novel branched PEO‐silanes with varying siloxane tether lengths and PEO molecular weight (M_n). Each PEO‐silane was crosslinked via acid‐catalyzed sol–gel condensation with α,ω‐bis(Si‐OH)polydimethylsiloxane (PDMS) (M_n = 3000 g/mol) to yield six amphiphilic silicone films. Film surface hydrophilicity increased with siloxane tether length, particularly after exposure to an aqueous environment, indicating that the PEO segments were more readily driven to the surface. This effect was more pronounced for films prepared with PEO‐silanes containing lower M_n PEO segments. AFM was used to study surface reconstruction of films upon exposure to an aqueous environment. Adsorption of bovine serum albumin (BSA) and human fibrinogen (HF) proteins decreased with siloxane tether length, particularly after first exposing films to an aqueous environment. For a given siloxane tether length, relatively less BSA adsorbed onto films prepared with PEO‐silanes with lower M_n PEO segments whereas less HF adsorbed onto films prepared with PEO‐silanes with higher M_n PEO segments. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4108–4119, 2010     

Highly selective multilayer polymer thin films for CO2/N2 separation

Multilayer thin films of poly(ethylene oxide) (PEO) and poly(methacrylic acid) (PMAA), deposited via layer‐by‐layer (LbL) assembly from aqueous solutions, are investigated for CO₂/N₂ separation. Eight and ten bilayer (217 and 389 nm thick, respectively) PEO/PMAA thin films deposited on a 25 μm polystyrene substrate exhibit CO₂/N₂ selectivities of 142 and 136, respectively. These are the highest reported to‐date for this gas pair separation using a homogeneous polymer film. While further work remains to improve CO₂ permeability, these results indicate the potential of LbL assemblies as standalone CO₂ separation membranes for low‐flux/high‐purity applications, or as part of a composite and/or mixed‐matrix membrane for high‐flux applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1730–1737     

Grafting polymerization of single‐handed helical poly(phenyl isocyanide)s on graphene oxide and their application in enantioselective separation

We herein report a “grafting from” strategy to immobilize optically active helical poly(phenyl isocyanide)s onto graphene oxide (GO) nanosheets. After covalently bounding alkyne‐Pd(II) initiator onto GO nanosheets, the designed GO/polymer composites P1 @GO and P1 ‐b‐ P2 @GO featuring single‐handed helical poly(phenyl isocyanide)s growing from GO nanosheets were prepared by sequential addition of the chiral and achiral isocyanide monomers. Post‐synthetic hydrolysis rendered P1 ‐b‐ P3 @GO to improve the hydrophilicity. The successful covalent bonding of poly(phenyl isocyanide)s chains onto GO nanosheets was certified by several cross evidences including scan emission microscopy, atomic force microscopy, Raman spectroscopy, X‐ray photoelectron spectroscopy, and thermogravimetric analysis. Circular dichroism spectra proved that the chiral information was introduced through the grafted single‐handed helical polymer chains successfully. In addition, the resulting GO/polymer composites were explored as a chiral additive to induce enantioselective crystallization of racemic organic molecules. Preferential formation of rod‐like L‐alanine crystals was induced by composites bearing right‐handed helical poly(phenyl isocyanide)s. The enantiomeric excess value of the induced crystals reached 76%, displaying the potential in future applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2092–2103     

Two calorimetric glass transitions do not necessarily indicate immiscibility: The case of PEO/PMMA

Differential scanning calorimetry has been used to examine blends of a poly(ethylene oxide) (PEO), M_n = 300 g/mol, and a poly(methylmethacrylate) (PMMA), M_n = 10,000 g/mol, across the complete composition range. The relatively low molar mass of the PEO minimizes interference from crystallization. In the midrange of composition, ～25–70% PEO, two broad, but distinct, glass transitions are resolved. These are interpreted as distinct glass transitions of the two components, as anticipated by the self‐concentration model of Lodge and McLeish. The composition dependence of the observed transitions is well described by the self‐concentration approach, using lengthscales of approximately two‐thirds of the Kuhn length. The results are compared with previous measurements on PEO/PMMA blends and other miscible systems. The principal, general conclusion is that one should actually expect two glass transitions in a miscible polymer blend or polymer solution; the rule of thumb that two transitions indicate immiscibility is incorrect. Furthermore, attempts to rationalize two transitions on the basis of incomplete segmental mixing, or other unspecified “nanoheterogeneity,” may not be justified in many cases. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 756–763, 2006     

Organocatalyzed ring‐opening polymerization of cyclic butylene terephthalate oligomers

In this study, various organic compounds, with different activation modes, have been tested as catalysts for the ring‐opening polymerization (ROP) of cyclic butylene terephthalate oligomers (CBT) in bulk at 210 °C, using tert‐butylbenzyl alcohol (tBnOH) as initiator. Among them, 1,3,5‐triazabicyclo[4.4.0]dec‐5‐ene (TBD) appeared to be the most efficient, achieving high monomer conversions in short reaction times (within minutes). Analysis by size‐exclusion chromatography (SEC) of the poly(butylene terephthalate) (PBT) synthesized using this catalyst also showed that the polymerization follows the expected theoretical M _n trend for molecular weights up to 50 kg·mol^?1. Chain‐end fidelity relatively to the alcohol initiator has been confirmed by MALDI‐TOF mass spectroscopy, which showed that all polymer chains possess the tert‐butylbenzyl moiety as chain‐end. Finally, to demonstrate the potential of this system for the synthesis of PBT‐based block copolymers, a monomethyl ether poly(ethylene glycol) (PEG) of 5000 g·mol^?1 has been employed as initiator for the ROP of CBT. A PEO‐b‐PBT block copolymer of 15,000 g·mol^?1 could thus been obtained, as confirmed by the shift of the SEC traces towards higher molecular weights and the same diffusion coefficient determined for ¹H NMR signals of the PEO block and the PBT block. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1611–1619     

Preparation and orthogonal postmodification of dual‐clickable polymer precursors bearing both aldehyde and alkyne groups

A new styrenic monomer 2‐propargyloxy‐5‐vinylbenzaldehyde (PVB) containing both aldehyde and alkyne reactive groups was designed for the synthesis and subsequent orthogonal postfunctionalization of dual‐clickable polymer precursor. Reversible addition‐fragmentation chain transfer polymerization of PVB afforded a structurally well‐defined polymer poly(2‐propargyloxy‐5‐vinylbenzaldehyde) (PPVB) bearing alkyne and aldehyde functionalities that are reactive towards azide ‐ and aminooxy‐containing molecules, respectively. Therefore, the resulting PPVB can be served as a dual‐clickable polymer scaffold for construction of multiple functional polymers via orthogonal alkyne–azide and aldehyde–aminooxy click reactions. Postpolymerization modification of PPVB sequentially with aminooxy‐terminated poly(ethylene oxide)s (H₂NO‐PEO) and azide‐functionalized imidazolium‐type ionic liquid (N₃‐IL·TFSI, having bis(trifluoromethane)sulfonamide, TFSI, counter‐anion) yielded an interesting multicomponent graft polymer PPVB‐g‐(PEO‐and‐IL·TFSI). After anion exchange of hydrophobic TFSI counter‐anion by bromide (Br) anion, the resulting graft copolymer PPVB‐g‐(PEO‐and‐IL·Br) becomes soluble in water, and its imidazolium units can capture negatively charged tetraphenylethylene disulfonate derivative (TPE‐2 ) guest molecule via electrostatic complexation to form in situ self‐assembled fluorescent nanoaggregates with colloidal stability imparted by hydrophilic PEO chains. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2650–2656     

A Facile Method to Form a Densely Grafted PEO‐b‐P4VP Brush on Gold Surface

Here we report a facile method for the preparation of a PEO₁₁₃‐b‐P4VP₉₃ brush on gold surface with a grafting density as high as 1.32 chains/nm²; the P4VP blocks were physically adsorbed on gold surface forming an inner layer while the PEO blocks stretched towards the solution forming PEO brush. PEO₁₁₃‐b‐P4VP₉₃ micelles with P4VP core and PEO shell formed in methanol/water mixed solvents were used as the precursor. By adsorbing PEO₁₁₃‐b‐P4VP₉₃ micelles from pure water, in which the density of the micelles is the largest, maximum amount of the micelles was adsorbed onto gold surface, and the adsorbed micelles existed as individual domains on the surface. To prepare the polymer brush with a density as high as possible, we annealed the adsorbed micelles by methanol/water mixed solvent at the volume fraction of methanol (VF) of 20%, which was the proper proportion at which the core‐forming P4VP chains began to be flexible but the integrity of the micelles was remained. At this volume fraction, almost all the adsorbed micelles originally existing as individual domains were transformed into a dense polymer brush.     

Determination of block size in poly(ethylene oxide)‐b‐polystyrene block copolymers by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry

Characterization of block size in poly(ethylene oxide)‐b‐poly(styrene) (PEO‐b‐PS) block copolymers could be achieved by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐TOF‐MS) after scission of the macromolecules into their constituent blocks. The performed hydrolytic cleavage was demonstrated to specifically occur on the targeted ester function in the junction group, yielding two homopolymers consisting of the constitutive initial blocks. This approach allows the use of well‐established MALDI protocols for a complete copolymer characterization while circumventing difficulties inherent to amphiphilic macromolecule ionization. Although the labile end‐group in PS homopolymer was modified by the MALDI process, PS block size could be determined from MS data since polymer chains were shown to remain intact during ionization. This methodology has been validated for a PEO‐b‐PS sample series, with two PEO of number average molecular weight (M_n) of 2000 and 5000 g mol^?1 and M_n(PS) ranging from 4000 to 21,000 g mol^?1. Weight average molecular weight (M_w), and thus polydispersity index, could also be reached for each segment and were consistent with values obtained by size exclusion chromatography. This approach is particularly valuable in the case of amphiphilic copolymers for which M_n values as determined by liquid state nuclear magnetic resonance might be affected by micelle formation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3380–3390, 2009     

Surface adsorption‐induced conformational ordering and crystallization of polyethylene oxide

The conformational ordering and crystallization of polyethylene oxide (PEO) in the presence of KBr surface were studied with in situ Fourier transform infrared spectroscopy (FTIR). KBr was chosen because of its low absorption on IR, which allows adding large amounts KBr into PEO matrix without sacrificing IR signal significantly. The presence of KBr enhances conformational order well above the melting temperature of PEO, which can further accelerate or decelerate the crystallization process. Low concentrations of KBr powder in the PEO melt promotes crystallization process, whereas high concentration of KBr restricts large portion of PEO chains on KBr surfaces, which hinder the diffusion and rearrangement of conformation and consequently slow down the crystallization process. Acceleration of crystallization requires a synergetic effect between the adsorbed chains with ordered conformation and the free chains with a fast diffusion rate, where the former and the later are responsible to lower the nuclei barrier and to maintain the low activation energy of diffusion, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 106–112, 2010     

Effects of hard‐segment polymers on CO2/N2 gas‐separation properties of poly(ethylene oxide)‐segmented copolymers

Poly(ethylene oxide)‐segmented polyurethanes (PEO‐PUs) and polyamides (PEO‐PAs) were prepared, and their morphology and CO₂/N₂ separation properties were investigated in comparison with those of PEO‐segmented polyimides (PEO‐PIs). The contents of the hard and soft segments in the soft and hard domains, W_HS and W_SH, respectively, were estimated from glass‐transition temperatures with the Fox equation. The phase separation of the PEO domains depended on the kind of hard‐segment polymer; that is, W_HS was in the order PU > PA ≫ PI for a PEO block length (n) of 45–52. The larger W_HS of PUs and PAs was due to hydrogen bonding between the oxygen of PEO and the NH group of urethane or amide. The CO₂/N₂ separation properties depended on the kind of hard‐segment polymer. Compared with PEO‐PIs, PEO‐PUs and PEO‐PA had much smaller CO₂ permeabilities because of much smaller CO₂ diffusion coefficients and somewhat smaller CO₂ solubilities. PEO‐PUs also had a somewhat smaller permselectivity because of a smaller solubility selectivity. This was due to the larger W_HS of PEO‐PUs and PEO‐PAs, that is, a greater contamination of PEO domains with hard urethane and amide units. For PEO‐PIs, with a decrease in n to 23 and 9, W_HS became large and CO₂ permeability decreased significantly, but the permselectivity was still at a high level of more than 50 at 35 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1707–1715, 2000     

Characterization of the interaction of poly(ethylene oxide) with nanosize fumed silica: Surface effects on crystallization

Poly(ethylene oxide) (PEO) of 4600 molar mass (PEO‐4600) was crystallized from methanol in the presence of hydrophilic fumed silicas (A380, A200, and OX50) with nominal surface areas of 380, 200, and 50 m²/g and a hydrophobic fumed silica (R812s) modified with methyl groups. The composites were characterized by thermogravimetric analysis and differential scanning calorimetry. The inhibition of crystallization and the tendency for chain reorganization after melting were in the order of A380 > A200 > OX50 > R812s, respectively, that is, both were least for the hydrophobic silica and increased with increasing specific surface area for the hydrophilic silica. The interaction of PEO with the silica increased in the melt state as compared with the solution‐cast samples, resulting in enhanced suppression of crystallization. The following took place at a high silica content: (1) crystallization occurred at crystallization temperatures [T_c < T_c (bulk)], suggesting that the silica inhibited crystallization; (2) crystallites with melt temperatures [T_m < T_m (bulk)] were observed, indictive of smaller and/or less perfect crystals; and (3) melt entropies [ΔS_m (surface) < ΔS_m (bulk)] suggested that the interaction of surface silanols, Si_sOH, with PEO decreased both the melt entropy and crystallite size/perfection. Crystallinity was observed in solution‐cast composites when there were greater than ～0.03 PEO molecules/nm² for native and ～0.01 PEO molecules/nm² for methylated fumed silica, similar to reported plateau equilibrium adsorption values from methanol. These results were consistent with a model in which PEO interacted more strongly with native fumed silica as compared with hydrophobically modified silica because of hydrogen bonding of the ether oxygens of PEO with the acidic silanols, preventing chain mobility and crystallization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1978–1993, 2003     

Disruptions in the crystallinity of poly(lauryl methacrylate) due to adsorption on silica

The effects of adsorption of poly(lauryl methacrylate) (PLMA), a side‐chain crystalline polymer, on silica were investigated. Fourier transform infrared spectroscopy and differential scanning calorimetry (DSC) measurements were made on both bulk and adsorbed PLMA. The reversible heat flow rates were observed as a function of temperature and the degree of crystallinity of the samples determined based on the broad melting transitions of the side chains in the surface samples. It was found that adsorption caused a disruption of the side‐chain crystallinity primarily in the tightly bound layer of the polymer, but did not significantly affect its glass transition temperature. A change in the packing of the hydrophobic side chains, as a result of adsorption, was also observed for the tightly adsorbed polymer. These results indicated that PLMA side chains in proximity to the silica surface have different properties from those in bulk PLMA. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 89–96     

ATNRC and SET‐NRC synthesis of PtBA‐g‐PEO well‐defined amphiphilic graft copolymers

A series of new well‐defined amphiphilic graft copolymers containing hydrophobic poly(tert‐butyl acrylate) backbone and hydrophilic poly(ethylene oxide) side chains were reported. Reversible addition‐fragmentation chain transfer homopolymerization of tert‐butyl 2‐((2‐bromopropanoyloxy)methyl)acrylate was first performed to afford a well‐defined backbone with a narrow molecular weight distribution (M_w/M_n = 1.07). The target poly(tert‐butyl acrylate)‐g‐poly(ethylene oxide) (PtBA‐g‐PEO) graft copolymers with low polydispersities (M_w/M_n = 1.18–1.26) were then synthesized by atom transfer nitroxide radical coupling or single electron transfer‐nitroxide radical coupling reaction using CuBr(Cu)/PMDETA as catalytic system. Fluorescence probe technique was employed to determine the critical micelle concentrations (cmc) of the obtained amphiphilic graft copolymers in aqueous media. Furthermore, PAA‐g‐PEO graft copolymers were obtained by selective acidic hydrolysis of hydrophobic PtBA backbone while PEO side chains kept inert. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012