反胶束法合成CdS纳米粒子及其表征

以AOT为保护剂,采用反胶束法合成CdS纳米粒子。利用水洗法洗去保护剂AOT,通过加入不同量的无水乙醇调节分散介质的极性,改变CdS纳米粒子在分散介质中的"溶解度",从而实现不同尺寸粒子的分离。采用紫外-可见(UV-vis)吸收光谱、透射电子显微镜(TEM)、荧光光谱法对其进行表征。     

溶剂对反胶束法合成CdS纳米粒子粒径的影响

以磺基琥珀酸二辛酯钠盐(AOT)为保护剂,利用反胶束法在不同烷烃溶液中合成了CdS纳米粒子.采用紫外-可见光谱、透射电子显微镜、荧光光谱法对其进行表征.研究表明:在不同烷烃溶液中合成的CdS纳米粒子,其粒子大小和荧光强度都随溶剂而改变.     

Preparation of Y2O3:Eu3+ nanoparticles in reverse micellar systems and their photoluminescence properties

Y2O3:Eu3+ phosphor nanoparticles (4-8 nm in size) with spherical morphology and narrow size distribution were obtained by calcination of composite Y-Eu hydroxide nanoparticles, which were prepared in sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/isooctane or polyethylene glycol mono-4-nonylphenyl ether (NP-5)/cyclohexane reverse micellar systems. This was achieved by the incorporation of the Y-Eu hydroxide nanoparticles into polyurea (PUA) via in situ polymerization of hexamethylene diisocyanate (HDI) in the reverse micellar solution and subsequent calcination of the resulting PUA materials. The emission intensity of the Y2O3:Eu3+ nanoparticles, prepared in the AOT/isooctane system, was significantly lower than that of the micrometer-size particles prepared in a homogeneous aqueous solution, since the calcined nanoparticles contained Na2SO4 impurity derived from the remaining AOT surfactant. The nanoparticles prepared in the NP-5/cyclohexane system, in contrast, showed higher emission intensity compared to the nanoparticles prepared in the AOT/isooctane system and longer luminescence lifetime compared to the micrometer-size particles prepared in the homogeneous aqueous solution. The photoluminescence intensity of Y2O3:Eu3+, prepared via the proposed process was found to decrease with decreasing the particle size.     

Orange-red luminescence from Cu doped CdS nanophosphor prepared using mixed Langmuir-Blodgett multilayers

Cu doped CdS nanophosphors were fabricated through Langmuir-Blodgett route for the first time. Precursors mixed Langmuir-Blodgett multilayers of cadmium arachidate-copper arachidate were used to grow doped sulfide nanoparticles within the organic matrix through postdeposition treatment with H(2)S gas. Changes in composition and layered structure of precursor multilayers were studied using Fourier transform infrared and x-ray reflection. Uptake of Cu in the multilayers was analyzed by inductively coupled plasma atomic emission spectroscopy measurements. Unannealed H(2)S exposed multilayers containing CdS nanoparticles show strong surface state emission centered at approximately 570 nm, whereas Cu doped CdS nanoparticles show orange-red luminescence. Photoluminescence (PL) spectra of annealed-Cu doped CdS nanoparticles show distinct Cu-related emission compared to annealed-undoped CdS nanoparticles. Power dependent PL measurements of annealed samples show that an efficient carrier recombination takes place at T(2) level of Cu(++). The carrier relaxation from the excitonic states to T(2) level results in the strong orange-red luminescence.     

Dithiol-mediated incorporation of CdS nanoparticles from reverse micellar system into Zn-doped SBA-15 mesoporous silica and their photocatalytic properties

CdS nanoparticles, as prepared in reverse micellar systems, were incorporated into alkanedithiol-modified Zn-doped SBA-15 mesoporous silica (dtz.sbnd;ZnSBA-15; pore diameter, ca. 4 nm), which were themselves prepared via hydrolysis of tetraethylorthosilicate (TEOS) in the presence of Zn(NO(3))(2) and triblock copolymer, as a nonsurfactant template and pore-forming agent, followed by contact with dithiol molecules. A particle-sieving effect for the dtz.sbnd;ZnSBA-15 was observed, in that the incorporation of the nanoparticles was remarkably decreased with increasing the nanoparticle size. The resulting CdSz.sbnd;ZnSBA-15 composite was then used as photocatalysts for the generation of H(2) from 2-propanol aqueous solution. Under UV irradiation (lambda>300 nm), a high photocatalytic activity was observed for this composite material. This is effected by electron transfer from the photoexcited ZnS (dithiol-bonded Zn on SBA-15) to CdS nanoparticles. The photocatalytic activity is increased with a decrease in the number of methylene groups in the dithiol molecules, according to the rank order 1,10-decanedithiol < 1,6-hexanedithiol < 1,2-ethanedithiol.     

Synthesis,Separation, and Characterization of Au@CdS Nanoparticles

The mixture of Au@CdS and CdS nanoparticles were obtained by reversed micelles method. n-Dodecanethiol was used to replace dioctylsulfosuccinate sodium salt (AOT) as a protector, and the surfactant AOT was washed away by water. By adding enthanol of different quantity, the polarity of dispersed medium was regulated and the solubility of Au@CdS and CdS nanoparticles in dispersed medium was adjusted. Consequently, the Au@CdS and CdS nanoparticles were separated effectively. Ultraviolet absorption spectra, transmission electronic microscopy (TEM), energy-dispersive X-ray analysis (EDX), and fluorescence spectra were used to characterize Au@CdS nanoparticles.     

CdS:Mn nanocrystals passivated by ZnS: synthesis and luminescent properties

Synthesis and characterization of highly luminescent ZnS-passivated CdS:Mn (CdS:Mn/ZnS) core/shell structured nanocrystals are reported. Mn-doped CdS core nanocrystals are produced ranging from 1.5 to 2.3 nm in diameter with epitaxial ZnS shell of wider band gap via a reverse micelle process. UV irradiation-stimulated photo-oxidation of the ZnS shell results in formation of sulfate (ZnSO(4)) as determined by x-ray photoelectron spectroscopy, which increases the photoluminescence emission intensity and subsequent photostability. Luminescent relaxation lifetime data present two different decay components, consisting of slow decay emission from the Mn center and a fast decay emission from a defect-related center. The impact of the density of surface defect states upon the emission spectra is discussed.     

The Effects of Methylene Blue on the Optical Properties of Nanometer-sized CdS Organosol

The inverse micelle system of nanometer-sized CdS doped with Methylene Blue(MB) was synthesized and characterized by using absorption and fluorescence spectra. The results show that MB molecules were absorbed onto the surface of CdS nanoparticles and interacted with surfactants when its concentration was lower than 4×10^-6 mol/L. From the comparison of their spectra, MB molecules by adsorption have a strong quenched fluorescence emission of CdS nanoparticles with surface defect states. All responses and main mechanism are ascribed to the charge transfer between the CdS organosol and Methylene Blue molecules.     

Steady-state photoinduced absorption of CdSe/CdS octapod shaped nanocrystals

Colloidal branched nanocrystals have been attracting increasing attention due to evidence of an interesting relationship between their complex shape and charge carrier dynamics. Herein, continuous wave photoinduced absorption (CW PIA) measurements of CdSe/CdS octapod-shaped nanocrystals are reported. CW PIA spectra show strong bleaching due to the one-dimensional (1D) CdS pod states (480 nm) and the zero-dimensional (0D) CdSe core states (690 nm). The agreement with previously reported ultrafast pump-probe experiments indicates that this strong bleaching signal may be assigned to state filling. Additional bleaching features at 520 and 560 nm are characterized by a longer lifetime and are thus ascribed to defect states, localized at the pod-core interface of the octapod, showing that some of the initially photogenerated carriers get quickly trapped into these long-lived defect states. However, we remark that a relevant part of electrons remain untrapped: this opens up the opportunity to exploit octapod shaped nanocrystals in photovoltaics applications, as electron acceptor materials, considering that several efficient hole extracting materials are already available for the realization of a composite bulk heterojunction.     

MoO3/ZrO2纳米固体强酸催化剂的制备及其在异丁烷-丁烯烷基化反应中的应用

利用AOT/异辛烷反胶束体系制备了MoO3/ZrO2纳米粒子.TEM结果表明,反胶束法制得粒子的粒径均匀,95%以上处于38～60nm之间.将此纳米粒子负载于γ-Al2O3上,呈现高度分散状态.NH3-TPD和烷基化反应的测定结果表明,其酸量和反应活性明显高于浸渍法和溶胶-凝胶法制备的样品,烷基化产物中C8的含量在79%左右.     

水热法合成CdS/ZnO核壳结构纳米微粒

以半胱氨酸镉配合物为前驱体,采用水热法合成CdS纳米微粒,并以ZnO对其进行表面修饰,形成具有核／壳结构的CdS／ZnO半导体纳米微粒,CdS纳米微粒表面经ZnO修饰后,其带边发射大大增强,透射电镜显示,110℃下反应4h所得的CdS／ZnO颗粒尺寸约为20nm,电子衍射表明其结构为六方相。     

Effects of the water content on the growth rate of AgCl nanoparticles in a reversed micelle system

The effects of water content on the growth rate and the final particle size of AgCl nanoparticles in a reversed micelle (RM) system of polyoxyethylene (6) nonylphenyl ether (NP-6)/water/cyclohexane were investigated using a double-jet technique, in which RM solutions of AgNO(3) and KCl were added concurrently to a RM solution containing the excess concentration of chloride ion. As a result, the particle growth rate and the final particle size at a constant Rw ( identical with[water]/[surfactant]) below 5 were found to be in excellent agreement with our theoretical prediction based on a dynamic Ostwald ripening mechanism governed by the overall solubility of the solid and the diffusivity of the reversed micelles, whereas the final particle size was far beyond the size of the water pool of a reversed micelle. Thus, the dramatic reduction of the particle size in the RM system can be explained by the drastic reduction of the overall solubility of the solid and the small diffusivity of the bulky reversed micelles as a carrier of silver ion, and not by the size of the water pool of a reversed micelle as conventionally explained. Some additional contribution of a coagulation process was also suggested in a high Rw range above 5. Significant coagulation of AgCl particles was observed in a RM system with AOT in place of NP-6 even under the standard conditions for the NP-6 system.     

憎水性三金属纳米粒子的合成、表征及磁性

以磺基琥珀酸二辛酯钠盐(AOT)为表面活性剂,采用反胶束法合成了憎水性CoFe/Au纳米粒子, 利用配体交换、水洗等去除AOT并使纳米粒子分级.采用紫外-可见光谱(UV-Vis)、透射电镜(TEM)、X射线衍射(XRD)、X射线电子能量散射(EDX)及等离子发射光谱 (ICP)等对产物进行了表征,通过超导量子干涉仪(SQIUD)研究了纳米粒子的磁性质.结果表明,反胶束法合成的CoFe/Au三金属纳米粒子具有较好的单分散性和稳定性,平均粒径约为4 nm.当外磁场强度为1.5×10⁴ A/m时,阻塞温度T_b为65 K,温度高于T_b时纳米粒子显示出超顺磁性,低于T_b时呈铁磁性,在5 K时其矫顽力(Hc)达4.67×10⁴ A/m.     

Solid state morphology and band gap studies of ETS-10 supported CdS nanoparticles

Engelhard titanosilicate (ETS-10) supported cadmium sulphide (CdS) nanoparticles were synthesized and characterized by various solid state techniques including: XRD, DR UV-Vis, TEM and FESEM. The effect of different synthesis routes of CdS nanoparticles on its physicochemical character was studied. It was observed that CdS nanoparticles prepared by both in situ sulphur reduction (CdS-IS) and reverse micelle (CdS-RM) methods showed similar roperties. However, CdS-IS nanoparticles are more feasible and economically practical. The reflectance measurements of the as-synthesized CdS nanoparticles are apparently blue-shifted compared to bulk CdS. This phenomenon of blue-shifted absorption edge has been ascribed to an increase in bandgap energy with a decrease in particle sizes. The bandgap of the as-synthesized CdS samples was calculated from the linear correlation of [F(R) hν]² and hν. The bandgap of CdS in ETS-10 was noticeably slightly reduced when compared with the as-synthesized CdS (8 nm) due to the formation of cluster arrays on the pores of ETS-10.     

On the Origin of the Large Stokes-Shift of the Emission of CdS Nanoparticles Embedded in a Phosphate Glass Matrix

XRD and TEM characterisation evidenced the formation of well-dispersed CdS nanoparticles inside a phosphate glass matrix. Optical absorption and time-resolved photoluminescence study were carried out on the prepared glass samples. Optical absorption revealed the fast character of the growth of CdS nanoparticles in this medium. Photoluminescence spectra showed only one large band with a maximum at almost 740 nm, which was associated to transitions between energy levels within the bandgap of the CdS nanoparticles. From the steady state and time-resolved measurements, it was suggested that the emission comes mainly from sulfur vacancies inside the nanocrystals and on its surface, which act as deep traps for the photogenerated electrons. The creation of such vacancies was attributed to the loss of sulfur during the glass preparation as evidenced from a chemical analysis using energy dispersive X-ray spectrometry. These traps may be also induced by the fast growth of CdS nanocrystals in this matrix or laser exposure during PL measurements. These CdS-doped glasses with an intense absorption in the UV–Vis region and a large emission band with long lifetime and a large Stokes-shift are adequate for luminescent solar concentrators, photocatalytic applications and solid-state lasers.     

Construction of inorganic nanoparticles by micro-nano-porous structure of cellulose matrix

In our previous work, the CdS nanoparticles/cellulose films exhibited significantly high photocatalytic H₂ production efficiency under visible light irradiation than the ordinary CdS photocatalyst. In present paper, the CdS nanoparticles were synthesized in situ in pores of the regenerated cellulose substrate and the porous structure of cellulose, formation of the CdS nanoparticles and interactions between CdS and cellulose matrix in the composite films were investigated deeply. The experimental results indicated that the micro-nano-porous structure of the cellulose matrix could be used easily to create inorganic nanoparticles, which supplied not only cavities for the formation of nanoparticles, but also a shell (semi-stiff cellulose molecules support the pore wall) to protect their nano-structure. When the cellulose films with porous structure at wet state were immersed into inorganic ions solution, the ions interacted immediately with the –OH groups of cellulose, and then transformed into inorganic composite via another treatment, finally inorganic nanoparticles formed during the dry. The pore size of the cellulose matrix decreased from 180 nm (at wet state) to about 18 nm (at dry state), leading to the formation of nanoparticles. The results revealed that the CdS nanoparticles with a mean particle diameter about 6 nm were dispersed well, and were immobilized tightly in the cellulose matrix, resulting in a portable photocatalyst with high efficiency for photocatalytic for H₂ evolution. This is simple and “green” pathway to prepare the organic–inorganic hybrid materials.     

Infra red quantum dot photolithography

CdS quantum dots were fabricated photolithographically on the surface and in the bulk of silica hydrogels, as well as on the surface of planar substrates. Silica hydrogels were prepared with a standard base-catalyzed route, and the solvent was exchanged with a cold aqueous solution of Cd(NO₃)₂, NH₄OH, thiourea, and a capping agent, e.g., 2-mercaptoethanol. The samples were then exposed to a focused infrared beam produced by a continuous-wave Nd:YAG laser. The precursors reacted upon heating, and CdS nanoparticles formed in the illuminated regions. Use of capping agents allowed to control the mean particle size, while focusing of the beam inside hydrogel monoliths generated nanoparticles in their bulk, but not at the surface. Planar substrates were patterned by illuminating a precursor solution spin-coated on the substrates. The average size of the CdS nanoparticles could be varied between about 1.5 and 4.5 nm by varying the type and the concentration of the capping agents.     

Synthesis and Stabilization of Gold Nanoparticles in Reverse Micelles of Aerosol OT and Triton X-100

Mechanisms of the formation and stabilization of gold nanoparticles in reverse micelles of micro-emulsions based on Triton X-100 (TX-100) and Aerosol OT (AOT) are studied. The instability of AOT-based microemulsions is shown to be caused by the oxidative degradation of gold nanoparticles in micelle water pools. Methods are proposed for the stabilization of these microemulsions. It is revealed that the mean size of gold nanoparticles synthesized in TX-100 reverse micelles in the presence of sodium sulfite is markedly smaller than that of particles prepared in AOT reverse micelles. This is explained by the fact that gold clusters are formed in the micelle shell rather than in the water pool. In the shell, the clusters are stabilized by oxyethylene groups of TX-100 molecules.__________Translated from Kolloidnyi Zhurnal, Vol. 67, No. 4, 2005, pp. 534–540.Original Russian Text Copyright © 2005 by Spirin, Brichkin, Razumov.     

Electric-field-induced changes in absorption and emission spectra of CdS nanoparticles doped in a polymer film

Electric-field-induced changes in absorption and emission spectra of colloidal CdS nanoparticles ranging in size from 1.0 to 5.0 nm in diameter have been measured by using electric field modulation spectroscopy. The analysis of the electroabsorption spectra indicates that the dipole moment in the first exciton state becomes larger with increasing particle size. The presence of the large dipole moment following photoexcitation into the first exciton band suggests that the CdS nanoparticles have large CT character in the first exciton state. The quantum yields both of the exciton emission and of the trap emission are markedly reduced by application of an electric field. On the basis of the direct measurements of the field-induced change in emission decay profile, it is suggested that the field-induced de-enhancement of these emission yields results from the field-induced decreases both in lifetime and in initial population of each emitting state. It is also found that the emission intensity of CdS nanoparticles increases under the UV light irradiation in air and decreases in a vacuum condition and that fluorescence lifetime in the former case is longer than that in the latter. This enhancement and de-enhancement process in emission intensity is almost reversible at least in several cycles.     

Dithiol-mediated immobilization of CdS nanoparticles from reverse micellar system onto Zn-doped silica particles and their high photocatalytic activity

Cds nanoparticles, prepared in a reverse micellar system, were immobilized directly onto alkanedithiol-modified Zn-doped silica particles, which were themselves prepared via hydrolysis of tetraethylorthosilicate in the presence of Zn(NO(3))(2) followed by contact with dithiol molecules. The resulting CdS-Zn-SiO(2) composite was then used as a photocatalyst for the generation of H(2) from 2-propanol aqueous solution. Under UV irradiation (lambda>300 nm), a high photocatalytic activity was observed for the CdS-Zn-SiO(2) composite material. This is effected by electron transfer from the photoexcited ZnS (dithiol-bonded Zn on SiO(2)) to CdS nanoparticles. The photocatalytic activity is increased with a decrease in the number of methylene groups in the dithiol molecules, according to the rank order 1,10-decanedithiol <1,6-hexanedithiol <1,2-ethanedithiol.