Evaluation of Photocatalytic Activity of Transparent Anatase Nanocrystals-Dispersed Silica Films Prepared by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals were precipitated mainly at the surface of the silica-titania gel films with hot water treatment, whereas the addition of poly(ethylene glycol) (PEG) in the films led to the dispersion of anatase nanocrystals in the whole of the films after the treatment. Both films with and without PEG showed high photocatalytic activities for acetaldehyde, NO _x and stearic acid in the gas-solid system, and for methylene blue and potassium iodide in the liquid-solid system. The addition of PEG improved the photocatalytic activities of the resultant films due to the smaller anatase crystallites and the porous film structure. The residual silica under-layer of the superficially anatase-precipitated films is expected to act as a protective one for an organic polymer substrate against the photocatalytic degradation.     

Formation of Anatase Nanocrystals in Sol-Gel Derived TiO2-SiO2 Thin Films with Hot Water Treatment

We have successfully prepared transparent and porous anatase nanocrystals-dispersed films by treating the sol-gel derived TiO₂-SiO₂ films containing poly(ethylene glycol), PEG, with hot water. This process was done at temperatures lower than 100°C under atmospheric pressure, and thus anatase nanocrystals-dispersed films can be formed on various kinds of substrates including organic polymers with poor heat resistance. The changes in structure and composition of the TiO₂-SiO₂ gel films with hot water treatment were related to the formation process of anatase nanocrystals in the TiO₂-SiO₂ gel films with hot water treatment. The formation of anatase nanocrystals was found to proceed to hydrolysis of Si–O–Ti bonds and dissolution of SiO₂ component. In addition, porous film structure formed by leaching of PEG with hot water treatment led to homogenous dispersion of anatase nonocrystals in the films.     

Formation of Anatase Nanocrystals-Precipitated Silica Coatings on Plastic Substrates by the Sol-Gel Process with Hot Water Treatment

Anatase nanocrystals-precipitated silica coatings were formed on plastic substrates such as poly(ethylene terephtalate) (PET), acrylic resin (AC) and polycarbonate (PC) from silica-titania gel coatings with and without addition of poly(ethylene glycol) (PEG) by hot water treatment. The maximum thickness of the coatings which can be formed without cracking or peeling-off was 100 to 200 nm for PET and PC substrates, whereas it was less than 50 nm for AC substrates. After a hot water treatment at 90°C for 120 min, the size of the anatase nanocrystals increased to be 30 and 50 nm for the coatings obtained with and without PEG, respectively. Anatase nanocrystals were formed throughout the whole of the coatings obtained with PEG and were formed only on the surface of the coatings obtained without PEG. Both coatings obtained with and without PEG were highly transparent. The plastic substrates with coatings obtained without PEG showed good weathering resistance owing to the protective effects of the residual silica under-layer. The coatings obtained with PEG showed higher photocatalytic activities than those obtained without PEG due to smaller size and higher dispersion of anatase nanocrystals in the coatings.     

Preparation and application of alumina- and titania- nanocrystals-dispersed thin films via sol-gel process with hot water treatment

A process to prepare nanocrystals-dispersed thin films at low temperatures using a hot water treatment of the gel films, and application of these nanocomposite thin films were demonstrated. When amorphous Al₂O₃ gel films were immersed in a hot water, we found that boehmite nanocrystals were formed on the surface of the films. In the hot water treatment of Al₂O₃-ZnO amorphous films, Zn-Al layered double hydroxide (LDH) was found to be formed on the films. When the SiO₂-TiO₂ gel films containing poly(ethylene glycol) were treated in a hot water, anatase nanocrystals were formed on the surface and inside of the films, and for the gel films without an organic polymer, the anatase nanocrystals were formed only on the surface of the films. In the hot water treatment of SiO₂-TiO₂ gel films under a vibration, titania nanosheets were found to be precipitated, instead of anatase nanocrysltals. Since formation of nanocrystals on the substrates using a hot water treatment is very mild conditions as the precipitation of crystals, we believe this process will open new application fields of nanocystals-dispersed thin films.     

Hard templating of nanocrystalline titanium dioxide with chiral nematic ordering

Anatase TiO(2) nanocrystals have been organized into high-surface-area (150-230 m(2) g(-1)) mesoporous films with long-range chiral nematic ordering. The chiral structure of the anatase films causes them to selectively reflect circularly polarized light and appear iridescent. These materials show replication of structural features found in the silica template on nanometer to millimeter length scales.     

Synthesis of TiO2 nanocoral structures in ever-changing aqueous reaction systems

A far-from-equilibrium strategy is developed to synthesize coral-like nanostructures of TiO(2) on a variety of surfaces. TiO(2) nanocoral structures consist of anatase base film and rutile nanowire layers, and they are continuously formed on substrates immersed in aqueous TiOSO(4)-H(2)O(2). The sequential deposition of TiO(2) starts with hydrolysis and condensation reactions of titanium peroxocomplexes in the aqueous phase, resulting in deposition of amorphous film. The film serves as adhesive interface on which succeeding growth of rutile nanowires to occur. This initial deposition reaction is accompanied by shift in pH of the reaction media, which is favorable condition for the growth of rutile nanocrystals. During the growth of rutile nanocoral layers, the amorphous base films are transformed to anatase phase. These sequential deposition reactions occur at temperatures as low as 80 °C, and the mild synthetic condition allows the use of a wide range of substrates such as ITO (indium tin oxide), glass, and even organic polymer films. The thickness of nanocoral layer is controllable by repeating the growth reaction of rutile nanocorals. TiO(2) nanocorals show photocatalytic activity as demonstrated by site-specific reduction of Ag(I) ions, which proceeds preferentially on the rutile nanowire layer. The rutile nanowire layer also shows photocatalytic decomposition of acetaldehyde, which is promoted upon increase of the thickness of the nanowire layer. The use of temporally transforming reaction media allows the formation of biphasic TiO(2) nanocoral structures, and the concept of nonequilibrium synthetic approach would be widely applicable to developing structurally graded inorganic nanointerfaces.     

Preparation of Co–Al and Ni–Al layered double hydroxide thin films by a sol–gel process with hot water treatment

Using hot water treatment of sol–gel derived precursor gel films, Co–Al and Ni–Al layered double hydroxide (LDH) thin films were prepared. The precursor gel films of Al₂O₃–CoO or Al₂O₃–NiO were prepared from cobalt or nickel nitrates and aluminum tri-sec-butoxide using the sol–gel method. Then, the precursor gel films were immersed in a NaOH aqueous solution of 100 °C. Nanocrystallites of Co–Al and Ni–Al LDH were precipitated with the hot water treatment with NaOH solution. The largest amounts of nanocrystals were obtained with a solution of pH = 10 for Co–Al LDH, and with that of pH = 9 for Ni–Al LDH. X-ray diffraction measurements confirmed that this process formed CO₃ ²⁻ intercalated LDHs. Both Co–Al and Ni–Al LDH thin films were confirmed to work as electrodes for electrochemical devices by cyclic voltammogram measurements.     

Formation of Superhydrophobic Alumina Coating Films with High Transparency on Polymer Substrates by the Sol-Gel Method

Transparent, superhydrophobic coating films have been prepared on polymer substrates at low temperatures through the sol-gel method. Al₂O₃ gel films were prepared on poly(ethylene terephthalate) substrates from Al(O-sec-C₄H₉)₃ chemically modified with ethyl acetoacetate. A small roughness of about 20–50 nm was found to form on the surface of the Al₂O₃ gel films dried at room temperature and then immersed in hot water at 60°C. The electron diffraction measurements have shown that this roughened surface consists of pseudoboehmite nanocrystals. The coating of hydrolyzed fluoroalkyltrimethoxysilane on the Al₂O₃ gel films with the small roughness produced transparent, superhydrophobic films with contact angle for water larger than 150°.     

Ultrathin Films of Porous Metal–Organic Polyhedra for Gas Separation

Ultrathin films of a robust Rh^II-based porous metal–organic polyhedra (MOP) have been obtained. Homogeneous and compact monolayer films (ca. 2.5 nm thick) were first formed at the air–water interface, deposited onto different substrates and characterized using spectroscopic methods, scanning transmission electron microscopy and atomic force microscopy. As a proof of concept, the gas separation performance of MOP-supported membranes has also been evaluated. Selective MOP ultrathin films (thickness ca. 60 nm) exhibit remarkable CO₂ permeance and CO₂/N₂ selectivity, demonstrating the great combined potential of MOP and Langmuir-based techniques in separation technologies.     

二氧化钛纳米晶溶胶内渗透电极对染料敏化太阳能电池的光伏性能的提高

以自制的过氧钛酸(PTA)水溶液为前驱体,用水热法制备了透明锐钛矿相二氧化钛溶胶.无需有机添加剂可得到直径小于7 nm的棒状二氧化钛纳米晶溶胶.通过将溶胶内渗透到染料敏化太阳能电池(DSSCs)的多孔二氧化钛电极后,消除了多孔电极内的大孔并改善了电极内纳米晶之间的连通性.用扫描电子显微镜(SEM)和光学轮廓仪对溶胶内渗透后的光阳极进行了表征.结果表明:小颗粒棒状二氧化钛纳米晶附着在多孔的二氧化钛表面,填充了电极由于烧结产生的大孔,并在多孔的二氧化钛内部形成了有利于电子传输的网络结构.与未经处理的多孔电极相比,改性后的光阳极组装成染料敏化太阳能电池后光电转化效率提高了64%.     

一种室温下制备多孔锐钛矿型TiO2薄膜的方法

 采用具有锐钛矿晶粒的TiO2溶胶与聚苯乙烯球形粒子混合制得涂膜液,通过浸渍提拉法制备薄膜,然后在超声波振荡条件下,以甲苯为溶剂,将薄膜中的聚苯乙烯球选择性地溶解去除,在室温下获得了锐钛矿型多孔TiO2薄膜. 与致密的TiO2薄膜相比,该多孔TiO2薄膜具有较高的光催化活性. 该方法有以下两方面的优点: 一是实现了多孔TiO2薄膜的室温制备,增大了薄膜基材的选择范围; 二是可以通过添加不同粒径的聚苯乙烯球,较为方便地实现了对薄膜孔径的调节.     

Rapid measurement of polymer photo-degradation by FTIR spectrometry of evolved carbon dioxide

A novel method, allowing simultaneous UV exposure of a polymer sample and IR interrogation of the vapour in a specially constructed cell, has been applied to polyethylene (PE) samples containing TiO₂ pigments with different photoactivities. Measurements of the CO₂ generated by films exposed to ultraviolet irradiation (UV) were completed in 5 h - very much less than conventional accelerated tests. The TiO₂ pigments used included anatase and rutiles with different surface treatments. Anatase pigmented material gave significantly higher CO₂ emission than unpigmented PE whilst rutile-pigmented PEs either gave reduced CO₂ emission or enhanced emission, according to the surface treatment. The ranking of the pigments as protectants or pro-degradants correlated well with the carbonyl index measured after more than 300 h exposure to UVA fluorescent tubes in a QUV machine.The method was then used to probe mechanistic aspects of the photo-oxidation of pigmented polyethylene (PE) film. For unpigmented polymer the photo-degradation was sensitive to changes in the small fraction of incident UV below 300 nm, but for pigmented films this was much less important. This is because unpigmented film degrades by direct photochemical attack whereas, for pigmented film, photocatalysis by TiO₂, which absorbs in the 300-400 nm region, is important. For films whose photo-oxidation was dominated by photocatalysis by the TiO₂ the rate of oxidation was shown to vary as the square root of the UV intensity. By contrast, for unpigmented films the rate of direct photochemical oxidation was linearly proportional to UV intensity. The difference is a consequence of the controlling role of electron-hole recombination in photocatalytic processes. For both unpigmented and pigmented films the rate of oxidation was shown to increase with increasing humidity and oxygen content of the atmosphere.     

BIODEGRADATION OF REGENERATED CELLULOSE FILMS BY FUNGI

The biodegradability of Aspergillus niger (A. niger), Mucor (M-305) and Trichoderma(T-311) strains on regenerated cellulose films in media was investigated. The results showedthat T-311 strain isolated from soil adhered on the cellulose film fragments has strongerdegradation effect on the cellulose film than A. niger strain. The weights, molecular weightsand tensile strengths of the cellulose films in both shake culture and solid media decreasedwith incubation time, accompanied by producing CO_2 and saccharides. HPLC, IR and re-leased CO_2 analysis indicated that the biodegradation products of the regenerated cellulosefilms mainly contain oligosaccharides, cellobiose, glucose, arabinose, erythrose, glycerose,glycerol, ethanal, formaldehyde and organic acid, the end products were CO_2 and water.After a month, the films were completely decomposed by fungi in the media at 30℃.     

Photoinduced hydrophilic and photocatalytic response of hydrothermally grown TiO2 nanostructured thin films

It is demonstrated that nanostructured titanium (IV) oxide (TiO₂) films can be deposited on glass substrates at 95 °C using hydrothermal growth, their properties being greatly affected by the substrate materials. Anatase TiO₂ films grown on ITO for deposition period of 50 h were observed to exhibit a very efficient, reversible light-induced transition to super-hydrophilicity, reaching a nearly zero contact angle. Enhanced photocatalytic activity (65%) was found for the rutile TiO₂ samples grown on microscope glass, possibly due to their higher roughness with respect to anatase grown on ITO. The effect of the substrate material used is discussed in terms of the TiO₂ phase and morphology control, for the best photoinduced hydrophilic and photocatalytic performance of the samples.     

Low Temperature Sol-Gel Preparation of Nanocrystalline TiO2 Thin Films

TiO₂ nanocrystalline thin films with varying degree of porosity have been prepared using a low temperature method. TiO₂ films of the anatase form have been obtained by using a polyethylene glycol (PEG) modified sol-gel method. Densification and crystallization of the films was found to result from the thermal treatment of the dip coated films in boiling water. The films have been characterized by Raman, XRD, FTIR, AFM and optical methods. Highly transparent films with transmission in excess of 85% and porosity as high as 58% are formed predominantly of anatase crystallites of dimensions of the order of 5 nm. Initial results on lithium intercalation into these films resulting in an efficient optical modulation in the visible and near infrared regions demonstrate a good potential of these films for electrochromic applications.     

Two step, hydrolytic-solvothermal synthesis of redispersible titania nanocrystals and their gas-sensing properties

A titanium chloromethoxide solution was prepared by reacting TiCl₄ with methanol, followed by water addition. The starting solutions were characterized by Fourier Transform Infrared (FTIR) spectroscopy, evidencing that the in situ generated water results in early hydrolysis of the chloroalkoxide. The solution was reacted with molten dodecylamine at room temperature, obtaining a white slurry of amorphous titania nanoparticles. Stable, redispersible TiO₂ nanocrystals could be prepared by subsequent solvothermal treatment in oleic acid at 250???C. The use of oleic acid was essential for obtaining crystalline structures, while other surfactants prevented crystallization. The nanocrystals were characterized by X-ray Diffraction and Transmission Electron Microscopy, confirming the formation of anatase TiO₂ nanocrystals with a mean size of 3.3?nm. The TiO₂ nanocrystals were used for fabricating gas-sensing devices, which were tested towards ethanol vapors. The initial small size of the nanocrystals, and the limited size growth during the high-temperature sensor operation, result in remarkable sensing performances if compared with bulk titania sensors.     

Cysteamine-modified ZIF-8 colloidal building blocks: Direct assembly of nanoparticulate MOF films on gold surfaces via thiol chemistry

Chemical modification of metal organic framework (MOF) nanocrystal colloids was used to endow them with chemical affinity for gold substrates. Modified nanocrystals were then used as building blocks for rapid and selective self-assembly of porous films. Cysteamine (Cys, 2-aminoetanethiol) was chosen as both chemical modulator and functionalizing agent of Zeolite Imidazolate Framework-8 (ZIF-8) MOF nanocrystals. Important parameters such as the impact of the modulator on the range of nanocrystals stability, size, polydispersity, morphology, and crystalline structure were assessed via both, small and wide angle x-ray scattering (SAXS and WAXS). Cysteamine modified ZIF-8 nanocrystals were assembled into films over conductive Au substrates and film growth was followed in-situ with Quartz Crystal Microbalance (QCM). Thiol moieties exposed out of the ZIF-8 surface after cysteamine modification, results in the formation of thiol bonds with Au conductive substrates as shown via Cyclic Voltammetry experiments. The strategy here presented allows for the synthesis of pre-designed building blocks for MOF films on metal surfaces.     

Preparation of Titania Nanosheet-Precipitated Coatings on Glass Substrates by Treating SiO2-TiO2 Gel Films with Hot Water Under Vibrations

Titania nanosheet-precipitated coatings have been prepared by treating SiO₂-TiO₂ gel films on glass substrates with hot water at 90°C under vibration. Longitudinal vibrations at about 6 Hz during the treatment enhanced the formation of titania nanosheet. The titania nanosheet consisted of several layers with a spacing of about 0.6 nm and was identified as hydrated titania with a lepidocrocite-type structure. The morphology of the titania nanosheet-precipitated coatings is probably achieved by lowering of the concentration of hydrolyzed titania species at the surface due to rapid water flow driven by the vibrations. The coatings were transparent in the visible range and showed high photocatalytic activity and antifogging property.     

Preparation and Characterization of Nanocrystalline Fe-Doped TiO2 Film on Different Substrates and Its Application in Degrading Dyeing Water

TiO₂ and Fe-doped TiO₂ thin films were prepared on the substrates (glass plates and glass microballs) after dipped in colloid and calcined at 500°C. The films have been characterized by UV-absorption, x-ray diffraction and atomic force microscopy (AFM). The investigated Fe-doped TiO₂ (A nominal 10 wt% Fe₂O₃ was impregnated) thin films were obtained by sol-gel method. The characterization results suggest that the calcined thin films primarily consist of TiO₂ anatase. And the light absorption curve of the TiO₂ films modified with Fe showed that red shift had happened by the dope of Fe. TiO₂/beads as photocatalyst were used to degrade the simulated dyeing water which contains reactive deep-blue dye (K-R). Through the degradation experiment, we found that the dope of Fe promoted the photocatalytic activities. The results showed that the dyeing water can be decomposed more effectively by the photocatalytic oxidation of Fe/TiO₂ film on glass micro-balls than glass plates.     

Anatase TiO2 porous thin films prepared by sol-gel method using CTAB surfactant

Anatase TiO₂ porous thin films were prepared on glass substrates by sol-gel method with Cetyltrimethylammonium Bromide (CTAB) as a pore-forming agent, Tetrabutylorthotitanate as Ti precursor, ethanol as solvent and diethanolamine as chelating agent respectively. IR, TG-DSC, XRD and SEM analyzed the chemical and physical changes during sol-gel process and characteristics of the films. Effects of the amount of CTAB, alkane and water on morphology of the films were discussed and the principle of forming porous structure was proposed. It was shown that the diameter of pores was changed in the range of 30–400 nm.