Growth and scintillation properties of the Na2W2O7 crystal

The growth and scintillation properties of the Na₂W₂O₇ crystal are reported. The solid reaction between Na₂CO₃ and WO₃ is used to synthesise the Na₂W₂O₇ material. The Na₂W₂O₇ single crystal has been grown by the Bridgman method. And the Na₂W₂O₇ single crystal with sizes 14×7×6 mm³ has been achieved. The transmission spectra, the Ultraviolet fluorescence spectra and the X-ray excited luminescence spectra of the Na₂W₂O₇ crystal are measured. The measurement results show that the Na₂W₂O₇ crystal is a promising intrinsic scintillator.     

Cs2LiGdCl6 (Ce): New scintillation material

We investigated the scintillation properties of Cs₂LiGdCl₆:Ce³⁺ as a function of the Ce concentration. X-ray excited luminescence spectra of the scintillation material showed broad emission bands between 360 and 460 nm, with two overlapping peaks, due to the d→f transitions on Ce³⁺ ions. The samples provide good scintillation results. The energy resolution was found to be 5.0% (FWHM) at 662 keV for 10% Ce sample. Under γ-ray excitation, Cs₂LiGdCl₆:Ce³⁺ showed three exponential decay time components of about 130–200 ns decay time constant. The light output of the investigated samples was 20,000 photons/MeV for a 10% Ce concentration. The light output deviation from the linear response is within 7% between the energy range of 31 and 1333 keV. Overall, the scintillation properties confirm that Cs₂LiGdCl₆:Ce³⁺ single crystal is a promising candidate for medical imaging and radiation detection.     

Growth and properties of Nd:Lu3Ga5O12 laser crystal by floating-zone method

Neodymium (Nd) doped lutetium gallium garnet (Nd:Lu₃Ga₅O₁₂, Nd:LuGG) single crystal was successfully grown by the optical floating-zone method for the first time to our knowledge. Its absorption and luminescence spectra at room temperature were measured. By using the J–O theory, the spectral parameters of Nd:LuGG were calculated, which indicated that Nd:LuGG should possess comparable and even better laser properties than Nd:YAG. The maximum output power of 855 mW at 1062 nm was achieved with slope efficiency of 23.4% under a pump power of 5.2 W, and optical conversion efficiency of 16.4%. All the results show that Nd:LuGG is a potential laser material.     

Crystal growth and spectroscopic properties of erbium doped Lu2SiO5

A high optical quality erbium doped Lu₂SiO₅ single crystal has been grown by the Czochralski method. The distribution coefficient of Er³⁺ was measured to be ∼0.926. The absorption and emission spectra as well as the fluorescence decay curve of the excited state ⁴I_13/2 were measured at room temperature. The spectroscopic parameters were calculated using the Judd–Ofelt theory, and the J–O parameters Ω₂, Ω₄ and Ω₆ were found to be 4.451×10^-20, 1.614×10^-20 and 1.158×10^-20 cm², respectively. The room-temperature fluorescence lifetime of the Er³⁺⁴I_13/2→⁴I_15/2 transition was measured to be 7.74 ms. The absorption and emission cross-section as well as the gain cross-section in the eye-safe regime of 1400–1700 nm were also determined and discussed.     

Crystal growth of Ce: PrF3 by micro-pulling-down method

Micro-pulling-down (μ-PD) growth apparatus was modified for fluoride crystals. PrF₃ was grown with various concentrations of Ce³⁺ from 0–100%. The crystals were transparent and colorless (CeF₃) or greenish and 3 mm in diameter and 15–50 mm in length. Neither visible inclusions nor cracks were observed. Radioluminescence spectra and decay kinetics were measured for the sample set at room temperature. In comparison to the Czochralski or Bridgman method, the μ-PD method allows to produce single crystalline material in a faster thus more economic way. Once it is established for the fluoride crystals, it is an efficient tool for exploring the field of new functional fluorides.     

Solar-blind 4.55 eV band gap Mg0.55Zn0.45O components fabricated using quasi-homo buffers

A route for synthesizing high Mg content single-phase wurtzite MgZnO films having band gaps in the solar-blind region is demonstrated by employing molecular beam epitaxy on Al₂O₃ substrates. Importantly, a low Mg content “quasi-homo” buffer, Mg_0.17Zn_0.83O, was applied to accommodate a host of structural discrepancies and therefore, avoiding phase separation in a high Mg content film, Mg_0.55Zn_0.45O, as proved by X-ray diffraction. The Mg fraction in the overgrown single-phase epilayer, Mg_0.55Zn_0.45O, was confirmed by Rutherford backscattering spectrometry.     

The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.     

Synthesis and characteristics of Na-doped Bi4Ti3O12 thin films on Si substrate

Bi_3.25Na_2.25Ti₃O₁₂ thin films were prepared on p-Si(1 1 1) substrate by a metalorganic solution decomposition (MOSD) method. The structural characteristic and crystallization of the films were examined by X-ray diffraction. The current–voltage characteristic shows ohmic conductivity in the lower voltage range and space-charge-limited conductivity in the higher voltage range. The dielectric constant is 53 at a frequency of 100 kHz at room temperature and the dissipation factor exists at a minimal value of 0.02 at a frequency of 200 kHz. The retention time estimated by measuring capacitance is about 10⁶ s. Nonhysteretic C–V curves at various frequencies were also collected.     

Influence of cooling rate on the liquid-phase epitaxial growth of Zn3P2

We report the liquid-phase epitaxial growth of Zn₃P₂ on InP (1 0 0) substrates by conventional horizontal sliding boat system using 100% In solvent. Different cooling rates of 0.2–1.0 °C/min have been adopted and the influence of supercooling on the properties of the grown epilayers is analyzed. The crystal structure and quality of the grown epilayers have been studied by X-ray diffraction and high-resolution X-ray rocking measurements, which revealed a good lattice matching between the epilayers and the substrate. The supercooling-induced morphologies and composition of the epilayers were studied by scanning electron microscopy and energy dispersive X-ray analysis. The growth rate has been calculated and found that there exists a linear dependence between the growth rate and the cooling rate. Hall measurements showed that the grown layers are unintentionally doped p-type with a carrier mobility as high as 450 cm²/V s and a carrier concentration of 2.81×10¹⁸ cm⁻³ for the layers grown from 6 °C supercooled melt from the cooling rate of 0.4 °C/min.     

Epitaxial growth of the CoFe2O4 film on SrTiO3 and its characterization

Cobalt ferrite (CoFe₂O₄) thin film is epitaxially grown on (0 0 1) SrTiO₃ (STO) by laser molecular beam epitaxy (LMBE). The growth modes of CoFe₂O₄ (CFO) film are found to be sensitive to laser repetition, the transitions from layer-by-layer mode to Stranski–Krastanov (SK) mode and then to island mode occur at the laser repetition of 3 and 5 Hz at 700 °C, respectively. The X-ray diffraction (XRD) results show that the CFO film on (0 0 1) SrTiO₃ is compressively strained by the underlying substrate and exhibits high crystallinity with a full-width at half-maximum of 0.86°. Microstructural studies indicate that the as-deposited CFO film is c-oriented island structure with rough surface morphology and the magnetic measurements reveal that the compressive strained CoFe₂O₄ film exhibits an enhanced out-of-plane magnetization (190 emu/cm³) with a large coercivity (3.8 kOe).     

Growth and shape control of orthorhombic Fe5(PO4)4(OH)3·2H2O single crystalline dendrites

Orthorhombic Fe₅(PO₄)₄(OH)₃·2H₂O single crystalline dendritic nanostructures have been synthesized by a facile and reproducible hydrothermal method without the aid of any surfactants. The influences of synthetic parameters, such as reaction time, temperature, the amount of H₂O₂ solution, pH values, and types of iron precursors, on the crystal structures and morphologies of the resulting products have been investigated. The formation process of Fe₅(PO₄)₄(OH)₃·2H₂O dendritic nanostructures is time dependent: amorphous FePO₄·nH₂O nanoparticles are formed firstly, and then Fe₅(PO₄)₄(OH)₃·2H₂O dendrites are assembled via a crystallization-orientation attachment process, accompanying a color change from yellow to green. The shapes and sizes of Fe₅(PO₄)₄(OH)₃·2H₂O products can be controlled by adjusting the amount of H₂O₂ solution, pH values, and types of iron precursors in the reaction system.     

Hydride-assisted growth of GaN nanowires on Au/Si(0 0 1) via the reaction of Ga with NH3 and H2

High quality, straight GaN nanowires (NWs) with diameters of 50 nm and lengths up to 3 μm have been grown on Si(0 0 1) using Au as a catalyst and the direct reaction of Ga with NH₃ and N₂:H₂ at 900 °C. These exhibited intense, near band edge photoluminescence at 3.42 eV in comparison to GaN NWs with non-uniform diameters obtained under a flow of Ar:NH₃, which showed much weaker band edge emission due to strong non-radiative recombination. A significantly higher yield of β-Ga₂O₃ NWs with diameters of ≤50 nm and lengths up to 10 μm were obtained, however, via the reaction of Ga with residual O₂ under a flow of Ar alone. The growth of GaN NWs depends critically on the temperature, pressure and flows in decreasing order of importance but also the availability of reactive species of Ga and N. A growth mechanism is proposed whereby H₂ dissociates on the Au nanoparticles and reacts with Ga giving Ga_xH_y thereby promoting one-dimensional (1D) growth via its reaction with dissociated NH₃ near or at the top of the GaN NWs while suppressing at the same time the formation of an underlying amorphous layer. The higher yield and longer β-Ga₂O₃ NWs grow by the vapor liquid solid mechanism that occurs much more efficiently than nitridation.     

High-resolution electron microscopy of microstructure of SrTiO3/BaZrO3 bilayer thin films on MgO substrates

SrTiO₃/BaZrO₃ heterofilms as buffer layers are deposited on (0 0 1) MgO substrates by an RF-sputtering technique. The atomic structure and the defect configuration at the interfaces are investigated by means of aberration-corrected high-resolution transmission electron microscopy. At the BaZrO₃/MgO interface, two types of interfacial structures, MgO/ZrO₂-type and MgO/BaO-type, are observed. Antiphase boundaries and dislocations are found at the BaZrO₃/MgO interface. The formation of these lattice defects is discussed in terms of film growth and structural imperfections of the substrate surface. At the SrTiO₃/BaZrO₃ interface, a high density of misfit dislocations is observed with different configurations. The formation of these dislocations contributes both to the relaxation of the large misfit strain and to stopping of the further propagation of lattice defects which are formed in the BaZrO₃ layer into the SrTiO₃ layer.     

Microstructural changes in epitaxial YBa2Cu3O7−δ thin films due to creation of O vacancies

Structural and transport properties of YBa₂Cu₃O_7−δ thin films subjected to different heat treatments and, consequently, having different O vacancy contents are investigated. It is observed that lattice parameters of the films follow the trend of the bulk material, indicating that either the additional stresses created in c-axis oriented films by O vacancies are negligibly small or they are relaxed at elevated temperatures. In addition, heat treatment under relatively low O₂ partial pressures, used to create O vacancies, leads to considerable reduction in local variations of lattice spacings in YBa₂Cu₃O_7−δ thin films.     

Mechanochemical metathesis synthesis and characterization of nano-structured MnV2O6·xH2O (x=2, 4)

A solid-state metathesis approach for the synthesis of hydrated MnV₂O₆·xH₂O (x=2, 4) materials driven by mechanochemical activation energy has been demonstrated. The metathesis pathway of forming the desired product is confirmed by the presence of high lattice energy by-product such as NaCl. The structural, optical, and chemical properties of the synthesized materials are examined by powder X-ray diffraction, X-ray photoelectron spectroscopy, thermo gravimetric analysis, scanning electron microscopy, transmission electron microscopy, and diffused reflectance measurements in the UV–vis range. The valence state of Mn and V was determined to be +2 and +5, respectively, for the title compounds and the bandgap values determined showed these materials are likely to be semiconductors.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Structure and optical properties of self-assembled InAs/GaAs quantum dots with In0.15Ga0.85As underlying layer

A high density of 1.02×10¹¹ cm⁻² of InAs islands with In_0.15Ga_0.85As underlying layer has been achieved on GaAs (1 0 0) substrate by solid source molecular beam epitaxy. Atomic force microscopy and PL spectra show the size evolution of InAs islands. A 1.3 μm photoluminescence (PL) from InAs islands with In_0.15Ga_0.85As underlying layer and InGaAs strain-reduced layer has been obtained. Our results provide important information for optimizing the epitaxial structures of 1.3 μm wavelength quantum dots devices.     

Preparation and characterization of fiber-textured SrAl2O4:Eu films grown using a homo-buffer layer

This paper describes the preparation and characterization of fiber-textured SrAl₂O₄:Eu films on a quartz glass substrate using a homo-buffer layer. The effect of the buffer layer on the crystallinity and adhesion was investigated by cross-section transmission electron microscopy and X-ray diffraction (XRD). The results show that the prepared film was not only well crystallized but also highly textured. The preferred orientation of this textured film was confirmed to be (0 3 1) by pole figure measurement. In addition, this film exhibits excellent optical transparency, with an average transmittance of more than 80% in the visible range.     

Dynamic process of crystallization of Sb2Se3 from Sb50Se50 amorphous film

Dynamics of crystallization of amorphous antimony-selenium film deposited on carbon substrate have been studied by the high-resolution transmission electron microscopy. The amorphous film was suddenly crystallized at 200°C by heating in vacuum. By the electron beam irradiation crystallization occurred at the focused electron beam region in the amorphous film. The growth process of crystallization by electron beam irradiation was recorded on a video image at the atomic resolution mode. The growth front of crystallization showed nano-concave and -convex shapes. The recrystallization with the different orientation at the first grown crystal have been found, and discussed as the influence of remaining antimony crystallites at the first crystallized film region.