Zn0.99Cu0.01Al2O4-SrTiO3微波陶瓷介电性能的研究

以分析纯Zn O、Cu O、Al2O3、Ti O2以及Sr CO3为原料,采用传统固相法制备了(1-x)Zn0.99Cu0.01Al2O4-x Sr Ti O3(ZCAST,x=0~0.045)微波介质陶瓷,利用X射线衍射仪、扫描电镜和网络分析仪对其结构、形貌和微波介电性能进行表征。研究了不同x值对ZCAST陶瓷相组成、显微结构以及微波介电性能的影响。结果表明,ZCAST陶瓷的体积密度、介电常数εr随着Sr Ti O3含量的增多而增大。当x=0.04具有最佳微波介电性能:介电常数εr=14.12,品质因数Q×f=28700 GHz,频率温度系数τf=-1.8×10-6/℃。     

氧化钽薄膜的结构、成份和介电性能研究

采用直流磁控反应溅射技术制备氧化钽薄膜,重点研究了溅射气体中Ar:O2比例和退火温度对样品的结构.成份和介电性能的影响.XRD、XPS和介电谱分析表明:Ar:O2比例对薄膜的结晶性能和薄膜中O/Ta原子比有较大影响,但对薄膜的介电性能没有明显的影响.900℃退火后,XRD谱中出现明显的β-Ta2O5(001)和(200)衍射峰;介电损耗谱表明介质的损耗是由微弱的电导产生的,漏电电流在损耗中占主导地位.     

(Na1/2Bi1/2)TiO3-(Na1/2Bi1/2)(Zn1/3Nb2/3)O3无铅压电陶瓷的介电特性研究

采用固相合成法制备了(1-x)(Na1/2Bi1/2)TiO3-x(Na1/2Bi1/2)(Zn/23Nb2/3)O3(简写为(1-x)NBT-xNBZN)无铅压电陶瓷.研究了该体系陶瓷晶体结构、弥散相变特征与介电弛豫行为.X射线衍射分析表明,所研究的组成均能够形成纯钙钛矿(ABO3)型固溶体.当x≥0.5%摩尔分数时,该体系陶瓷具有三方、四方共存的晶体结构.材料的介电常数-温度曲线显示陶瓷具有两个介电反常峰Tf和Tm.修正的居里-外斯公式较好的描述了陶瓷弥散相变特征,弥散指数随x的增加而增加.x≤0.5%摩尔分数的陶瓷仅在低温介电反常峰Tf附近表现出明显的频率依赖性,随x的增加,陶瓷材料在室温和低温介电反常峰Tf之间都表现出明显的频率依赖性.根据有序-无序转变和宏畴.微畴转变理论探讨了该体系陶瓷介电弛豫特性的机理.     

Ka波段微波衰减陶瓷的研制

为研制出适用于Ka波段(26.5～40GHz)微波管的高性能微波衰减陶瓷,在Al2O3-TiO2微波衰减陶瓷的基础上,开展了添加钨粉、改变烧结方法对材料电磁参数和热导率影响的研究.结果表明,用热压烧结方式并添加20wt;粒度为4～5 μm的钨粉,可制造出综合性能良好的Ka波段专用微波衰减陶瓷.这一衰减陶瓷的典型性能为,介电常数13.90～21.83,损耗角正切0.20 ～1.02,热导率2.92 W/m·K.     

Al2O3掺杂对微波介质陶瓷Ca0.16Sr0.04Li0.4Nd0.4TiO3烧结特性和微波介电性能的影响

采用固相反应法在1300℃烧结4h得到了致密的具有钙钛矿结构的Ca0.16Sr0.04Li0.4Nd0.4TiO3微波介质陶瓷.通过X射线衍射仪、扫瞄电子显微镜和矢量网络分析仪系统的研究了不同含量Al2O3掺杂对Ca0.16Sr0.04Li0.4Nd0.4TiO3(CSLNT)陶瓷的烧结行为、晶体结构、显微形貌以及微波介电性能的影响.结果表明,对于CSLNT+ xwt;Al2O3陶瓷,随着Al2O3掺杂量的增加,介电常数(εr)有轻微的降低,而温度系数(τf)有所增加;由于第二相的出现导致了品质因子(Q·f)先增后减.当Al2O3掺杂量为2wt;时,其介电性能最佳的致密化烧结温度为1200℃,此时具有最佳的微波介电性能:εr=112.6,Q·f=1698 GHz和τf=31.9 ppm/℃.     

Co掺杂对ZnO晶体中光生电子瞬态过程的影响

采用气相反应制备了ZnO和ZnO∶Co微晶,并通过热释光研究了材料中的电子陷阱能级(施主能级),采用微波介电谱研究了材料的光生电子瞬态过程.发现纯ZnO热释光谱有两个峰,分别为-183 ℃和-127 ℃,说明存在两个电子陷阱能级;而ZnO∶Co中热释光信号很弱,只有纯ZnO的十分之一.微波介电谱研究表明,由于电子陷阱对导带电子的驰豫作用,纯ZnO材料导带光电子的衰减为一级指数过程,寿命为802 ns.ZnO∶Co微晶体的最大微波介电谱强度低于纯ZnO晶体的五分之一,电子陷阱密度较小,其光生电子快速衰减,过程仅为10～20 ns.结果说明Co掺杂具有明显的抑制电子陷阱能级生成的作用.     

常压烧结Mg2SiO4-SiC复相材料的微波衰减性能

以Mg2SiO4和SiC为原料,Al2O3-BaO-SiO2作为复合烧结助剂,H2气氛下在1450℃下保温1h常压烧结制备出了Mg2SiO4-SiC复相微波衰减材料;采用X射线衍射、扫描电子显微镜对复相材料的相组成、显微结构进行表征.研究了SiC添加量对复相材料X波段(8～ 12 GHz)微波衰减性能的影响.结果表明:通过加入一定量的Al2O3BaO-SiO2复合烧结助剂能有效促进烧结致密化,复相材料的显气孔率均在0.5;以下;SiC含量从0增加到10;,复相材料谐振频率由11.8 GHz递减到10.0 GHz,衰减峰值的绝对值由3.62 dB递减到1.18 dB,有效衰减带宽由0.48 GHz递增到1.03 GHz,随着SiC含量的增加,谐振频率向低频移动,衰减峰绝对值降低,有效衰减带宽增大.     

溶胶-凝胶法制备MgxZn1-xO及其特性

采用溶胶-凝胶法制备了不同组分(x=0.1～0.3)的MgxZn1-xO前驱体,并对它进行不同温度的热处理(550℃～1000℃).X射线衍射(XRD)结果表明,Mg0.1Zn0.9O具有和ZnO一样的衍射谱,为六方纤锌矿结构,而且随着热处理温度的升高,ZnO衍射峰的强度逐渐增强,半高宽不断减小;Mg元素掺杂浓度增大后,出现了MgO的峰位.扫描电子显微镜(SEM)显示Mg0.1Zn0.9O晶粒粒径分布较均匀;热处理温度升高,晶粒的尺寸不断变大.用室温荧光光谱(PL)分析了经过550～1000℃热处理获得的Mg0.1Zn0.9O粉末,结果发现除了550℃下处理的样品,其它都有紫外发射峰(350nm左右),而且随着热处理温度的升高紫外峰有明显的蓝移现象.     

蓝宝石衬底上GaN薄膜的结构和光学特性表征

采用低压金属有机化学气相沉积(LPMOCVD)法,成功地在(0001)晶向的蓝宝石(Al2O3)衬底上制备了高质量的GaN薄膜.并利用X射线衍射(XRD)谱和椭圆偏振光谱(SE)对其结构和光学特性作了表征.XRD谱中,在34.5°和72.9°附近出现了两个尖锐的衍射峰,分析表明这两个衍射峰分别对应纤锌矿(Wurtzite) 结构GaN薄膜的(0002)和(0004)晶向.其中GaN (0002)晶向衍射峰的半高宽(FWHM)很窄,只有0.1°左右,并且GaN(0004)晶向衍射峰强度很强,二者均证实了采用LPMOCVD法制备的GaN薄膜具有高的质量.在介电函数和反射谱中,GaN高的透明性(＜3.44eV)诱导了强的干涉振荡.室温下拟合出的表征带间跃迁的光学带隙约为3.44eV.     

水热法辅助溶胶-凝胶法制备Al∶ZnO纳米棒阵列及发光性能研究

采用水热法结合溶胶-凝胶法在SiO2基片上制备了不同Al含量掺杂的ZnO纳米棒阵列.通过X射线衍射仪(XRD),电子扫描显微镜(SEM),透射光谱和光致发光光谱仪(PL)等测量手段,分析了Zn1-xAlxO薄膜样品的微结构、表面形貌、透射及光致发光特性.结果表明,制备出的Zn1-xAlxO薄膜具有良好的结晶质量和明显的沿(002)方向择优取向生长.透射谱分析显示,样品的吸收边随Al含量的增加出现明显的红移现象.PL谱分析表明,掺杂Al以后,薄膜出现强的橙红光发射光谱带,通过谱线拟合,发现在可见光波段的缺陷发光主要是位于能量为1.92eV和2.15 eV的红光及黄光发射,主要发光机理为Zn,缺陷发射.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.     

New zeotype borophosphates with chiral tetrahedral topology: (H)0.5M1.25(H2O)1.5[BP2O8]·H2O (M = Co(II) and Mn(II))

Two new isostructural open‐framework zeotype transition metal borophosphate compounds, (H)_0.5M_1.25(H₂O)_1.5[BP₂O₈]·H₂O (M = Co(II) and Mn(II)) were synthesized by mild hydrothermal method. The structure of compounds were characterized by single‐crystal X‐ray diffraction which have ordered, alternating, vertex‐sharing BO₄, PO₄, and (MO₄)OM(H₂O)₂ groups with hexagonal, P 6₁ 2 2 (No 178) space group and unit cell parameters for Co a = 9.4960(6) Å, c = 15.6230(13) Å, for Mn a = 9.6547(12) Å, c = 15.791(3) Å, Z = 1 for both of them. TGA/DTA analysis, IR spectroscopy were used for characterization. Magnetic susceptibility measurements for both of the compound indicate strong antiferromagnetic interaction between metal centers. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

Solubility of Ag2O into the Na2O–B2O3–Al2O3 system

The solubility of Ag₂O was measured for the Na₂O–B₂O₃ and Na₂O–B₂O₃–Al₂O₃ system with the rotating crucible method and static method, respectively, under air atmosphere at temperatures ranging from 1273 to 1423 K. The contamination of melts from crucibles could be avoided by the rotating crucible method, with which it became possible to measure the solubility of Ag₂O for the Na₂O–B₂O₃ system above the melting point of Ag for the first time. It was found that the addition of Na₂O decreases the solubility of Ag₂O while the addition of Al₂O₃ had little effect on the solubility. The effect of Na₂O and Al₂O₃ on the solubility of Ag₂O is expressed by interaction coefficients and is analyzed in terms of the basicity of melts. The solubility of Ag₂O in Na₂O–B₂O₃–Al₂O₃ melts increased with increased temperature. This phenomena was explained by a small enthalpy change in oxidation of silver.     

Considerations on the structure and physical properties of B2O3-SiO2 and GeO2-SiO2 glasses

Data of density, refractive index and thermal expansion coefficient for B₂O₃-SiO₂ and GeO_2-SiO₂ glasses have been analyzed. The volumes of the structural units are the same found for the vitreous B₂O₃, GeO₂ and SiO₂. The volume of any structural unit is constant over the entire composition region of the glass system. The same has been found for the differential refraction and unit refraction of the structural units in these glasses. Different features are observed for the differential expansion of the structural units. There is a considerable change with composition in the differential expansion of BO₃, GeO₄ and SiO₄ units. The effect is attributed to a change in the asymmetry of vibrations with the number of Si-O-B or Si-O-Ge linkages in the matrix. The thermal expansion coefficient is mainly determined by the contribution of B₂O₃ or GeO₂ in the concerned glasses.     

Molecular structure and crystal packing of uncomplexed 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C22H18N4O2

The X-ray crystal structure of 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C₂₂H₁₈N₄O₂, is determined. The crystal packing is dominated by phenyl stacking interactions. Weak C–H···N hydrogen bonds help align the molecules. C–H··· hydrogen bonding is not apparent.     

Structural and electrical properties of vapour phase grown Cd1 − xFexTe single crystals

Cd_1 − xFe_xTe single crystals were prepared by vapour phase growth method in the composition range of 0 ≤ x ≤ 0.03. Chemical analysis, surface morphology, structural investigations and electrical properties were carried out by EDAX, SEM, XRD, TEM and transport technique, respectively. Microscopic variations between the target and actual compositions were noticed. Morphology studies revealed that dislocation aided growth is active in the present crystals. TEM and XRD studies confirmed that the samples of all compositions crystallized in zinc blende structure, and the lattice parameters varied almost linearly decreases with Fe content. At room temperature, the resistivity of the Cd_1 − xFe_xTe crystals of all compositions (x = 0.01, 0.015, 0.02, 0.025 and 0.03) lies in the range of 3.5-6.5 M Ω, the activation energies lie in the range of 63-133 meV, and the samples were show the ‘p’ type conductivity.     

空位浓度对纤锌矿CdS电子结构和光学性质影响的第一性原理研究

本文基于密度泛函理论的平面波超软赝势方法,采用第一性原理研究了含Cd空位缺陷CdS和含S空位缺陷纤锌矿CdS的几何结构、能带结构、电子态密度及光学性质。通过计算分析可知,含Cd空位缺陷的CdS体系均为p型半导体,含S空位缺陷的CdS体系跃迁方式均由直接跃迁变为间接跃迁。Cd、S空位缺陷的CdS体系的态密度总能量降低。空位CdS体系相较于本征CdS体系的静介电常数均有提高,并随着空位浓度的增大而增大,Cd空位缺陷体系更为明显,极化能力得到显著提升。空位Cd的CdS体系相较于本征CdS体系在红外波段存在明显的吸收,空位S的CdS体系相较于本征CdS体系在可见光波段存在明显的吸收。