钛酸钡陶瓷制备及介电性能研究

采用钛酸四丁酯和硝酸钡为主要原料的微波辅助草酸盐沉淀法,在最佳的工艺参数下合成晶粒尺寸约为30～ 50 nm的钛酸钡粉末.再通过对纳米粉体造粒、成型、排胶和烧结等工艺处理制备钛酸钡陶瓷.研究陶瓷的最佳烧结温度与烧结时间,并且讨论其对介电性能的影响规律.利用透射电子显微镜分析粉体的形貌,XRD和扫描电子显微镜分别分析陶瓷的物相和断面形貌.结果表明,利用微波辅助草酸盐沉淀法合成的粉体制备陶瓷的烧结温度为1270℃,烧结时间为3h.并且其介电常数在室温下可达到2397.6.     

微波水热法制备ZnO纳米晶

采用微波水热(microwave hydrothermal,M-H)法在MDS-6型温压双控微波水热反应仪中成功地制备出平均晶粒尺寸为30 nm且呈现棒状形貌的ZnO纳米晶.并在一定的水热温度和反应时间下系统研究了微波水热反应过程中[Zn2+]离子浓度、反应釜填充比、反应物浓度比[Zn2+]/[OH]等工艺因素对ZnO纳米晶的晶粒尺寸及形貌的影响.采用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)和透射电子显微镜(TEM)对所制备的ZnO纳米晶进行表征.结果表明:所制备ZnO的平均晶粒尺寸约为30 nm,ZnO纳米晶呈现棒状形貌.随着[Zn2+]离子浓度的增加,ZnO纳米晶的晶粒尺寸先减小后增大;随着反应釜填充比和反应物浓度比[Zn2+]/[OH]的增大,ZnO纳米晶的晶粒尺寸先减小后增大,并逐渐趋于稳定.制备ZnO纳米晶的最佳反应条件为:[Zn2+]=1.6 mol·L-1;反应釜填充比=70;;[Zn2+]/[OH]=1/2.     

微波辅助草酸盐沉淀法制备四方相钛酸钡纳米粉体

以钛酸四丁酯和硝酸钡为主要原料,采用微波辅助草酸盐沉淀法制备了纯度高、结晶度较好的四方相钛酸钡纳米粉体.分别采用X射线衍射分析(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对钛酸钡纳米粉体的结构、粒径及形貌进行表征.结果表明,在钡/钛摩尔比为1,微波温度80 ℃、微波时间30 min,煅烧温度700 ℃,煅烧时间1 h,通过添加表面活性剂OP-10,制备出粒径在50 nm左右且四方度为1.0069的钛酸钡纳米粉体,其中微波合成温度及合成时间对钛酸钡纳米粉体的四方度的影响较大.     

反应温度和添加剂含量对微波合成碳化硼微观形貌的影响

微波烧结由于具有高效、快速、绿色等特点越来越受到人们的关注.本文以天然煤粉(C)和硼酸(H3BO3)为原料,在无气氛保护条件下,利用2.45 GHz的TE666单频微波烧结炉,快速碳热还原反应法制备出纳米碳化硼(B4C)粉体.结果发现:当煤粉(C)和硼酸(H3BO3)质量比为3∶1,微波烧结温度为1400~1800 ℃,保温时间为5 min,即可制备出结晶良好的碳化硼(B4C)晶体,调整相关工艺参数可以控制B4C晶体的形貌,如直径为50~150 nm的球形颗粒或碳化硼片状结构,通过改变Na2CO3添加剂含量(3wt;~9wt;),可得到不同尺寸的碳化硼纳米片(边长为200~800 nm),获得传统电阻烧结条件下无法得到的碳化硼(B4C)晶体.     

微波烧结制备铁酸铋陶瓷的介电性和铁电性

采用微波烧结法制备铁酸铋多铁陶瓷,研究了微波烧结时间对其显微结构、介电性和铁电性的影响.结果表明:在4 kW下烧结35～40 min制备出基本为纯相的铁酸铋陶瓷;随烧结时间增加,铁酸铋陶瓷结构越来越致密,晶粒尺寸有一定程度增大;在-10～90℃范围内,介质损耗随烧结时间增加而增大;随微波烧结时间增加,剩余极化强度增大,而矫顽场强先增加后减小,且铁电性具有明显的频率依赖性;铁酸铋陶瓷的漏电流随微波烧结时间增加而减小,这是结构致密化的结果.     

烧结升温速率对钛酸钡陶瓷压电性能的影响

采用固相反应方法在不同烧结升温速率下制备了BaTiO3陶瓷,并对陶瓷样品的晶体结构、表面形貌、介电、压电和铁电性能进行了测试和分析.结果表明:当烧结升温速率为3 ℃/min和5 ℃/min时陶瓷均为四方钙钛矿晶格结构,随升温速率的增大,四方相程度增强,材料平均晶粒尺寸减小,压电系数和铁电性能随之降低,但介电常数随之增大,当烧结升温速率为5 ℃/min介电常数最大,其值为3144.当烧结升温速率为1 ℃/min时陶瓷为正交钙钛矿晶格结构d33和Pr最大,其值为Pr=10 μC/cm2和d33=193 pC/N.     

锆钛酸钡陶瓷的超低温烧结及其介电特性

利用钛酸四丁酯、硝酸锆、氢氧化钡为原料在室温下,直接合成了颗粒尺寸均匀,组分连续可调的高性能锆钛酸钡纳米粉体.在此基础上,通过添加不同比例的Bi2O3和Li2CO3为助烧剂,实现了900℃下的陶瓷的超低温烧结.确立了烧结时间与陶瓷微观结构之间的相关性.研究表明,助烧剂的加入,可以使介电峰强烈地向低温方向移动,室温介电常数可大于5000以上.某些情况下使介电峰分裂,由单一峰变为明显的双峰,这样使得介电常数的温度稳定性得到提高.     

Sr2+置换改性Ca0.25(Li1/2Sm1/2)0.75TiO3陶瓷的微波介电性能研究

采用固相法制备了(Ca1-xSrx)0.25(Li1/2Sm1/2)0.75TiO3(CSLST-x)( x= 0～1/10)系列微波介质陶瓷材料,研究不同含量的Sr2+含量对该体系的相组成、烧结性能和微波介电性能影响.在x=1/22～1/10范围内,Sr2+的掺杂不会改变晶体的结构;在1175～1200 ℃烧结时,相同烧结温度下随着Sr2+含量的增加,介电常数εr增大,无载品质因数与谐振频率乘积Qf值降低;置换离子Sr2+的添加使该体系的烧结温度降低了近200 ℃,并保持良好的微波介电性能.其中,x=1/16的CSLST陶瓷在1200 ℃烧结,保温5 h时具有较好的微波介电性能:εr=97.2,Qf=2490 GHz,τf =14.74 ppm/℃.     

微波辅助水热合成条件对直接合成纳米HZSM-5晶体性质的影响

利用微波辅助水热合成法直接制备了纳米HZSM-5晶体.采用XRD、FT-IR、SEM、BET和NH3-TPD等手段对合成样品进行了分析表征,研究了晶化温度和时间对合成产物晶体性质的影响.结果表明,晶化温度和时间对微波辅助水热直接合成产物微观形貌、晶粒尺寸和分散度影响明显.较低的晶化温度和较短的晶化时间均难以形成形貌规则的HZSM-5晶体.随着晶化温度的升高,合成样品逐渐变为球形晶粒、晶粒尺寸逐渐增大、分散度逐渐提高,继续提高晶化温度达180 ℃时,晶粒长大使比表面积稍有降低;随着晶化时间的延长,样品的微孔和介孔增多,比表面积和孔容逐渐增大,继续延长晶化时间,晶体内微孔可能的收缩和晶粒的长大使得样品孔容和比表面积减小.160 ℃和1.5 h条件下制备的HZSM-5分子筛晶体形貌呈球形,晶粒尺寸约为60 nm,分散程度较好;其比表面积、孔容和平均孔径分别为398.45 m2·g-1、0.63 cm3·g-1和6.27 nm;晶体表面具有弱酸特征.     

锆钛酸钡钙压电陶瓷的晶粒尺寸效应研究进展

锆钛酸钡钙无铅压电陶瓷具有可与锆钛酸铅媲美的压电性能,受到国内外广泛关注.晶粒尺寸是影响锆钛酸钡钙陶瓷电性能的重要因素,其晶粒尺寸效应已成为研究的热点.为此,综述了粉体制备方法、烧结方法、烧结温度和保温时间对锆钛酸钡钙陶瓷的晶粒尺寸及其电性能的影响,并提出了研究中亟待解决的问题.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.     

New zeotype borophosphates with chiral tetrahedral topology: (H)0.5M1.25(H2O)1.5[BP2O8]·H2O (M = Co(II) and Mn(II))

Two new isostructural open‐framework zeotype transition metal borophosphate compounds, (H)_0.5M_1.25(H₂O)_1.5[BP₂O₈]·H₂O (M = Co(II) and Mn(II)) were synthesized by mild hydrothermal method. The structure of compounds were characterized by single‐crystal X‐ray diffraction which have ordered, alternating, vertex‐sharing BO₄, PO₄, and (MO₄)OM(H₂O)₂ groups with hexagonal, P 6₁ 2 2 (No 178) space group and unit cell parameters for Co a = 9.4960(6) Å, c = 15.6230(13) Å, for Mn a = 9.6547(12) Å, c = 15.791(3) Å, Z = 1 for both of them. TGA/DTA analysis, IR spectroscopy were used for characterization. Magnetic susceptibility measurements for both of the compound indicate strong antiferromagnetic interaction between metal centers. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

Solubility of Ag2O into the Na2O–B2O3–Al2O3 system

The solubility of Ag₂O was measured for the Na₂O–B₂O₃ and Na₂O–B₂O₃–Al₂O₃ system with the rotating crucible method and static method, respectively, under air atmosphere at temperatures ranging from 1273 to 1423 K. The contamination of melts from crucibles could be avoided by the rotating crucible method, with which it became possible to measure the solubility of Ag₂O for the Na₂O–B₂O₃ system above the melting point of Ag for the first time. It was found that the addition of Na₂O decreases the solubility of Ag₂O while the addition of Al₂O₃ had little effect on the solubility. The effect of Na₂O and Al₂O₃ on the solubility of Ag₂O is expressed by interaction coefficients and is analyzed in terms of the basicity of melts. The solubility of Ag₂O in Na₂O–B₂O₃–Al₂O₃ melts increased with increased temperature. This phenomena was explained by a small enthalpy change in oxidation of silver.     

Considerations on the structure and physical properties of B2O3-SiO2 and GeO2-SiO2 glasses

Data of density, refractive index and thermal expansion coefficient for B₂O₃-SiO₂ and GeO_2-SiO₂ glasses have been analyzed. The volumes of the structural units are the same found for the vitreous B₂O₃, GeO₂ and SiO₂. The volume of any structural unit is constant over the entire composition region of the glass system. The same has been found for the differential refraction and unit refraction of the structural units in these glasses. Different features are observed for the differential expansion of the structural units. There is a considerable change with composition in the differential expansion of BO₃, GeO₄ and SiO₄ units. The effect is attributed to a change in the asymmetry of vibrations with the number of Si-O-B or Si-O-Ge linkages in the matrix. The thermal expansion coefficient is mainly determined by the contribution of B₂O₃ or GeO₂ in the concerned glasses.     

Molecular structure and crystal packing of uncomplexed 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C22H18N4O2

The X-ray crystal structure of 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C₂₂H₁₈N₄O₂, is determined. The crystal packing is dominated by phenyl stacking interactions. Weak C–H···N hydrogen bonds help align the molecules. C–H··· hydrogen bonding is not apparent.     

Structural and electrical properties of vapour phase grown Cd1 − xFexTe single crystals

Cd_1 − xFe_xTe single crystals were prepared by vapour phase growth method in the composition range of 0 ≤ x ≤ 0.03. Chemical analysis, surface morphology, structural investigations and electrical properties were carried out by EDAX, SEM, XRD, TEM and transport technique, respectively. Microscopic variations between the target and actual compositions were noticed. Morphology studies revealed that dislocation aided growth is active in the present crystals. TEM and XRD studies confirmed that the samples of all compositions crystallized in zinc blende structure, and the lattice parameters varied almost linearly decreases with Fe content. At room temperature, the resistivity of the Cd_1 − xFe_xTe crystals of all compositions (x = 0.01, 0.015, 0.02, 0.025 and 0.03) lies in the range of 3.5-6.5 M Ω, the activation energies lie in the range of 63-133 meV, and the samples were show the ‘p’ type conductivity.     

空位浓度对纤锌矿CdS电子结构和光学性质影响的第一性原理研究

本文基于密度泛函理论的平面波超软赝势方法,采用第一性原理研究了含Cd空位缺陷CdS和含S空位缺陷纤锌矿CdS的几何结构、能带结构、电子态密度及光学性质。通过计算分析可知,含Cd空位缺陷的CdS体系均为p型半导体,含S空位缺陷的CdS体系跃迁方式均由直接跃迁变为间接跃迁。Cd、S空位缺陷的CdS体系的态密度总能量降低。空位CdS体系相较于本征CdS体系的静介电常数均有提高,并随着空位浓度的增大而增大,Cd空位缺陷体系更为明显,极化能力得到显著提升。空位Cd的CdS体系相较于本征CdS体系在红外波段存在明显的吸收,空位S的CdS体系相较于本征CdS体系在可见光波段存在明显的吸收。