低温超晶格YSZ/STO/YSZ电解质薄膜的制备及表征

采用脉冲激光沉积法(PLD),在Al2O3 (ALO)衬底上,将Y2O3∶ZrO2(YSZ)和SrTiO3 (STO)按照YSZ/STO/YSZ的顺序依次沉积,形成超晶格YSZ/STO/YSZ电解质薄膜,利用SEM、XRD和交流阻抗对其形貌、相结构和电学性能进行了表征.结果表明,衬底温度为700℃形成的超晶格YSZ/STO/YSZ电解质薄膜颗粒大且均匀,排列紧密且呈规律圆柱状;YSZ、STO均沿(111)方向择优生长;低温时电导率比单层YSZ电解质薄膜高出4个数量级,是较为理想的低温固体燃料电池电解质.     

Ce0.8Sm0.2O1.9-BaCe0.8Sm0.2O2.9复合电解质的成分对其电化学性能的影响

采用一步溶胶凝胶法制备摩尔比分别为9∶1、7∶3、5∶5和3∶7的复合电解质Ce0.8Sm0.2O1.9(SDC)-BaCe0.8Sm0.2O2.9(BCS)粉末,研究复合电解质SDC-BCS的相成分对电导率及其电化学性能的影响.结果表明:随着SDC含量的增加,复合电解质SDC-BCS的晶粒尺寸增大、电导率提高;复合电解质的晶界电导率均高于单相SDC的晶界电导率.不同成分的复合电解质制备的NiO-SDC-BCS|SDC-BCS|LSCF-SDC-BCS单电池的功率密度随着SDC含量的增加而提高.当SDC∶BCS的摩尔比为9∶1时,其单电池700 ℃的最大功率密度为550 mW/cm2,是单电池NiO-SDC|SDC|LSCF-SDC最大功率密度的3倍.     

原料NiO粉末对燃料电池Ni/SDC阳极材料微结构和性能的影响

分别采用商用氧化镍和煅烧碱式碳酸镍所得氧化镍粉末与Ceo.8Smo.2O2-δ(SDC)粉末混合,经压制烧结制得燃料电池NiO/SDC阳极烧结体,经H2还原后得到Ni/SDC金属陶瓷阳极材料,考察了不同NiO原料和加入量对阳极烧结体和阳极材料的微结构及相关性能的影响,还对以Ni/SDC为阳极构建的燃料电池单电池的性能进行了测试.实验结果表明:煅烧碱式碳酸镍所得NiO粉末和商用NiO粉末的平均粒径分别约为1.1 μm和8μm,前者更为均匀细小;由煅烧碱式碳酸镍所得NiO所制备的Ni/SDC阳极材料具有更高的电导率,含40; NiO的阳极材料(S-Ni/40SDC),在H2气氛中的电导率可达117.5 S·cm-1.以煅烧碱式碳酸镍所得的NiO制备的NiO/SDC为阳极,SDC为电解质,(Y0.5Ca0.5) BaCo3ZnO7-50SDC为阴极的单电池在700℃下的最大输出功率达225 mW/cm2,开路电压为0.85 V,电池性能优于以商用NiO为阳极原料所构建的单电池.     

反应磁控溅射制备AZO薄膜相结构的演化及机理研究

在室温下,利用直流反应磁控溅射技术在不同的氧气流量下沉积ZnO∶ Al (AZO)薄膜.采用XRD、SEM和TEM技术分析薄膜相成分、表面截面形貌及微观结构.结果表明:氧气流量为2.5 sccm时,沉积形成的薄膜为不透明具有金属导电性能的AZO/Zn( AZO)双层复合膜结构;氧气流量为3.5 sccm时,沉积形成了透明导电的AZO薄膜;氧气流量为5.0 sccm时,形成了透明不导电且含有纳米Al2O3颗粒的AZO薄膜;此外,AZO薄膜在400℃退火后,薄膜晶粒长大和(002)晶面方向择优生长更加明显以及高氧气流量沉积的AZO薄膜中的纳米Al2O3颗粒消失.     

固体氧化物燃料电池电解质8YSZ薄膜的水系流延

本文采用水系浆料流延成型法制备固体氧化物燃料电池SOFC的电解质材料(8;摩尔分数Y2O3,稳定的ZrO2,下称8YSZ)薄膜,研究了三种不同类型的分散剂对8YSZ浆料稳定性的影响.通过优化pH值和分散剂用量等因素,使浆料的稳定性达到最佳,获得固相含量高达62;质量分数的适合流延的8YSZ水系浆料.以该浆料为原料,采用流延的方法成型8YSZ薄膜,获得了显微结构均匀、相对密度达49.4;、表面光滑、无裂纹、柔韧性好、干燥后厚度为50 μm左右的薄膜素坯.该素坯在1350℃保温4 h烧结得到相对密度大于96;的致密8YSZ烧结薄膜.     

柠檬酸法制备固体氧化物燃料电池阳极材料Ni/SDC

采用硝酸盐-柠檬酸法合成出不同NiO含量的NiO/Ce_(0.8)Sm_(0.2)O_(1.9)(NiO/SDC)复合粉体,借助差热热重、XRD等对粉体的形成条件和相组成等进行了分析,并对粉体的比表面、粒度等进行了测定.由NiO/SDC粉体制备出固体氧化物燃料电池Ni/SDC金属陶瓷阳极材料,并对其微结构及相关性能进行了测试分析.结果表明:硝酸盐-柠檬酸法可以在较低的温度下合成出高比表面积的NiO/SDC粉体.制备的Ni/SDC阳极材料具有均匀细小的晶粒度和孔隙,以及高的电导率.1350 ℃烧结含55;NiO的NiO/SDC烧结体还原后所得Ni/SDC试样的孔隙率和电导率(700 ℃,H_2中)分别为38;和1825 S·m~(-1).     

衬底温度对Cu2O薄膜结构和性能的影响

采用射频磁控溅射技术在石英衬底上制备了Cu2O薄膜。系统研究了衬底温度对薄膜结构、光学和电学性能的影响。XRD的结果显示,在所有衬底温度条件下均可得到单相的Cu2O结构,而且随着衬底温度由500 K升至800 K,薄膜表现出(111)择优取向的生长特点。电学和光学测试结果表明,室温电导率和光学带隙随着衬底温度的升高而增加,800 K制备的薄膜的带隙值最高约为2.58 eV。     

不同应力下的双层钙钛矿锰氧化物La1.3Sr1.7Mn2O7薄膜输运特性研究

采用脉冲激光沉积(PLD)法分别在SrTiO3(100)、LaAlO3 (100)和MgO(100)单晶基片上制备了双层钙钛矿锰氧化物La13Sr17Mn2O7(LSMO)薄膜.X射线衍射谱表明三个样品均沿衬底的晶向择优生长;原子力显微镜显示薄膜表面均光滑致密.采用标准四探针法对薄膜的阻温特性进行了研究,发现SrTiO3 (100)和LaAlO3(100)基片上生长的薄膜呈现出明显的金属-绝缘体转变,转变温度分别为340 K和330 K.而在MgO基片上显示绝缘体态,无金属-绝缘体转变.结合阻温曲线的拟合及薄膜与衬底的晶格失配计算,从薄膜应力和激活能变化的角度分析了样品出现不同阻温特性的内在机制.     

多晶氮化铜薄膜制备及性能研究

采用反应射频磁控溅射的方法在不同的氮气分压的条件下,在玻璃基底上成功制备了氮化铜(Cu3N)薄膜.XRD显示氮气的气氛影响薄膜的择优生长取向,在低氮气气氛时薄膜择优[111]晶向生长,在高的氮气气氛条件下薄膜的择优生长取向为[100].用Scherrer公式估算出薄膜晶粒的大小在17～26nm之间,实验并研究了薄膜的热稳定性和电学性质.结果表明,薄膜的热稳定性较差,在200℃退火1h后已经完全呈Cu的相,薄膜的电阻率随着填隙原子的数目减少从导体到绝缘体发生不连续的改变.     

溅射功率对脉冲磁控溅射沉积Cu2O薄膜结构和光学性能的影响

利用脉冲磁控溅射制备技术,采用单质金属铜靶作为溅射靶,在氧气(O2)和氩气(Ar)的混合气氛下,在石英玻璃衬底上制备了Cu2O薄膜.研究了溅射功率对脉冲反应磁控溅射沉积法在室温下对生长Cu2O薄膜结构、表面形貌及光学性能的影响.结果表明,在O2、Ar流量比(O2/Ar)为30∶80的气氛条件下,在60～90 W的溅射功率范围内可获得＜ 111＞取向的Cu2O薄膜;薄膜的表面粗糙度的均方根值随溅射功率的增加而增大;薄膜的光谱吸收范围为300 ～670 nm,不同溅射功率下制备的薄膜均在430 nm附近出现明显的带边吸收,其光学带隙(Eg)在2.15～2.53 eV之间变化.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

New zeotype borophosphates with chiral tetrahedral topology: (H)0.5M1.25(H2O)1.5[BP2O8]·H2O (M = Co(II) and Mn(II))

Two new isostructural open‐framework zeotype transition metal borophosphate compounds, (H)_0.5M_1.25(H₂O)_1.5[BP₂O₈]·H₂O (M = Co(II) and Mn(II)) were synthesized by mild hydrothermal method. The structure of compounds were characterized by single‐crystal X‐ray diffraction which have ordered, alternating, vertex‐sharing BO₄, PO₄, and (MO₄)OM(H₂O)₂ groups with hexagonal, P 6₁ 2 2 (No 178) space group and unit cell parameters for Co a = 9.4960(6) Å, c = 15.6230(13) Å, for Mn a = 9.6547(12) Å, c = 15.791(3) Å, Z = 1 for both of them. TGA/DTA analysis, IR spectroscopy were used for characterization. Magnetic susceptibility measurements for both of the compound indicate strong antiferromagnetic interaction between metal centers. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Solubility of Ag2O into the Na2O–B2O3–Al2O3 system

The solubility of Ag₂O was measured for the Na₂O–B₂O₃ and Na₂O–B₂O₃–Al₂O₃ system with the rotating crucible method and static method, respectively, under air atmosphere at temperatures ranging from 1273 to 1423 K. The contamination of melts from crucibles could be avoided by the rotating crucible method, with which it became possible to measure the solubility of Ag₂O for the Na₂O–B₂O₃ system above the melting point of Ag for the first time. It was found that the addition of Na₂O decreases the solubility of Ag₂O while the addition of Al₂O₃ had little effect on the solubility. The effect of Na₂O and Al₂O₃ on the solubility of Ag₂O is expressed by interaction coefficients and is analyzed in terms of the basicity of melts. The solubility of Ag₂O in Na₂O–B₂O₃–Al₂O₃ melts increased with increased temperature. This phenomena was explained by a small enthalpy change in oxidation of silver.     

Considerations on the structure and physical properties of B2O3-SiO2 and GeO2-SiO2 glasses

Data of density, refractive index and thermal expansion coefficient for B₂O₃-SiO₂ and GeO_2-SiO₂ glasses have been analyzed. The volumes of the structural units are the same found for the vitreous B₂O₃, GeO₂ and SiO₂. The volume of any structural unit is constant over the entire composition region of the glass system. The same has been found for the differential refraction and unit refraction of the structural units in these glasses. Different features are observed for the differential expansion of the structural units. There is a considerable change with composition in the differential expansion of BO₃, GeO₄ and SiO₄ units. The effect is attributed to a change in the asymmetry of vibrations with the number of Si-O-B or Si-O-Ge linkages in the matrix. The thermal expansion coefficient is mainly determined by the contribution of B₂O₃ or GeO₂ in the concerned glasses.     

Molecular structure and crystal packing of uncomplexed 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C22H18N4O2

The X-ray crystal structure of 1,6-bis(N-cyano-p-methoxy-anilino)-2,4-hexadiyne, C₂₂H₁₈N₄O₂, is determined. The crystal packing is dominated by phenyl stacking interactions. Weak C–H···N hydrogen bonds help align the molecules. C–H··· hydrogen bonding is not apparent.     

Structural and electrical properties of vapour phase grown Cd1 − xFexTe single crystals

Cd_1 − xFe_xTe single crystals were prepared by vapour phase growth method in the composition range of 0 ≤ x ≤ 0.03. Chemical analysis, surface morphology, structural investigations and electrical properties were carried out by EDAX, SEM, XRD, TEM and transport technique, respectively. Microscopic variations between the target and actual compositions were noticed. Morphology studies revealed that dislocation aided growth is active in the present crystals. TEM and XRD studies confirmed that the samples of all compositions crystallized in zinc blende structure, and the lattice parameters varied almost linearly decreases with Fe content. At room temperature, the resistivity of the Cd_1 − xFe_xTe crystals of all compositions (x = 0.01, 0.015, 0.02, 0.025 and 0.03) lies in the range of 3.5-6.5 M Ω, the activation energies lie in the range of 63-133 meV, and the samples were show the ‘p’ type conductivity.     

空位浓度对纤锌矿CdS电子结构和光学性质影响的第一性原理研究

本文基于密度泛函理论的平面波超软赝势方法,采用第一性原理研究了含Cd空位缺陷CdS和含S空位缺陷纤锌矿CdS的几何结构、能带结构、电子态密度及光学性质。通过计算分析可知,含Cd空位缺陷的CdS体系均为p型半导体,含S空位缺陷的CdS体系跃迁方式均由直接跃迁变为间接跃迁。Cd、S空位缺陷的CdS体系的态密度总能量降低。空位CdS体系相较于本征CdS体系的静介电常数均有提高,并随着空位浓度的增大而增大,Cd空位缺陷体系更为明显,极化能力得到显著提升。空位Cd的CdS体系相较于本征CdS体系在红外波段存在明显的吸收,空位S的CdS体系相较于本征CdS体系在可见光波段存在明显的吸收。