The effect of MgO on the thermodynamics of the Fe/Fe-redox equilibrium and the incorporation of iron in soda-magnesia-aluminosilicate melts

Melts with the basic compositions 10Na₂O · 10MgO · xAl₂O₃ · (80−x)SiO₂ (x=0, 5, 10, 15 and 20), 10Na₂O · xMgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10, 15 and 20) and xNa₂O · 10MgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10 and 15) all doped with 0.25 mol% Fe₂O₃ were studied using square-wave voltammetry. The temperatures applied were in the range of 1000–1600 °C. The square-wave voltammograms recorded show peaks caused by the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials measured decreased linearly with decreasing temperatures. Increasing the MgO-concentration led to more negative peak potentials. Introducing alumina in the melt first resulted in less negative peak potentials. If the molar Al₂O₃-concentration is equal to that of Na₂O (=10 mol%) the peak potentials are least negative. Further increase of the Al₂O₃-concentration led to more negative peak potentials. The variation of the Na₂O-concentration led to a maximum in the peak potentials at an Na₂O-concentration of 10 mol%. An empirical formula which allows the calculation of standard potentials from the chemical composition is proposed. Furthermore, a structural explanation for the effect of the chemical composition is given. Especially, the incorporation of Al₂O₃ as AlO₄⁻-tetrahedra at [Al₂O₃] < [Na₂O] and as network modifier at larger concentrations was structurally explained by the similarities of Fe²⁺ and Mg²⁺, with respect to cation radii and metal–oxygen bond lengths.     

Solubility of YBa2Cu3O7−δ and Nd1+xBa2−xCu3O7±δ in the BaO/CuO flux

The knowledge of the phase relations and solubilities in the Y–Ba–Cu–O and Nd–Ba–Cu–O systems are of fundamental importance for crystal growth and liquid-phase epitaxy of YBa₂Cu₃O_7−δ (YBCO) and Nd_1+xBa_2−xCu₃O_7±δ (NdBCO). The determination of the solubility curve of YBCO and NdBCO in a BaO/CuO flux containing 31 mol% BaO was done by observation of the formation and dissolution of crystals on the surface of the high-temperature solution. The heat of the solution of YBCO at 1000°C was found to be 34.7 kcal/mol, and for NdBCO at 1060°C, it was found to be 28.1 kcal/mol. The determination of the solubility curves requires special care, and the problems of the time-dependent shift of the solution composition due to the corrosion of the crucible is discussed. The scatter of the solubility data published by different authors could be due to the use of solutions with different Ba : Cu ratios, different determination methods, i.e. different crystallization mechanisms, different crucibles and starting chemicals.     

Electronic traps in mixed Si1−xGexO2 films

Thermally stimulated luminescence (TSL) and infrared (IR) spectroscopy were measured in plasma grown Si_1−xGe_xO₂ (x=0, 0.08, 0.15, 0.25, 0.5) with different thicknesses (12–40 nm). A comparison with the TSL properties of thermally grown SiO₂ and GeO₂ was also performed. A main IR absorption structure was detected, due to the superposition of the peaks related to the asymmetric O stretching modes of (i) Si–O–Si (at ≈1060 cm⁻¹) and (ii) Si–O–Ge (at 1001 cm⁻¹). Another peak at ≈860 cm⁻¹ was observed only for Ge concentrations, x>0.15, corresponding to the asymmetric O stretching mode in Ge–O–Ge bonds. A TSL peak was observed at 70°C, and a smaller structure at around 200°C. The 70°C peak was more intense in all Ge rich layers than in plasma grown SiO₂. Based on the thickness dependence of the signal intensity we propose that at Ge concentrations 0.25x0.5 TSL active defects are localised at interfacial regions (oxide/semiconductor, Ge poor/Ge rich internal interface, oxide external surface/atmosphere). Based on similarities between TSL glow curves in plasma grown Si_1−xGe_xO₂, thermally grown GeO₂ and SiO₂ we propose that oxygen vacancy related defects are trapping states in Si_1−xGe_xO₂ and GeO₂.     

B NMR investigations in xV2O5–B2O3 and xV2O5–B2O3–PbO glasses

11B (I=3/2) MAS NMR in the binary glass system xV₂O₅–B₂O₃ (x=0.053, 0.43) and the ternary glass system xV₂O₅–B₂O₃–PbO (0.1x1.5) has been investigated at room temperature. In the xV₂O₅–B₂O₃ glasses, one NMR line due to BO₃ unit was observed. Meanwhile in the xV₂O₅–B₂O₃–PbO, two NMR lines which arise from BO₃ and BO₄ units were detected, where the appearance of BO₄ units is produced by the presence of PbO. From the computer-simulation of the ¹¹B NMR central transition line (m=−1/2↔1/2), the quadrupole parameters (e²qQ/h and η) for BO₃ units in xV₂O₅–B₂O₃, and those for BO₃ and BO₄ units in xV₂O₅–B₂O₃–PbO were obtained as a function of x. As the V₂O₅ content increases in xV₂O₅–B₂O₃–PbO, the e²qQ/h and η values of the BO₃⁻ associated resonance are found to slightly decrease and increase, respectively. Meanwhile, the e²qQ/h and η values of BO₄⁻ associated resonance in xV₂O₅–B₂O₃–PbO are found to slightly increase and decrease, respectively. By comparing the intensities of the total transitions (m=−3/2↔−1/2,m=−1/2↔1/2, and 1/2↔3/2) for the ¹¹B NMR line of BO₃ and BO₄ units contained in xV₂O₅–B₂O₃–PbO with those of respective standard samples of 0.053V₂O₅–B₂O₃ and NaBH₄, the quantitative fractions of BO₃ and BO₄ in xV₂O₅–B₂O₃–PbO were obtained as a function of x.     

Properties and structure of RO---Na2O---Al2O3---P2O5 (R = Mg, Ca, Sr, Ba) glasses

The properties and structure of (45 - x)RO · xNa₂O · 2.5Al₂O₃ · 52.5P₂O₅ (R = Mg, Ca, Sr, Ba, 0 x 31 mol%) glasses were investigated. The variation in the molar volumes of glasses in the MgO series is closely related to the formation of the end groups in the glasses with the substitution of Na⁺ ions for Mg²⁺ ions, resulting in a variation of the density and refractive index of the glasses. The properties of glasses containing CaO in terms of Na₂O substitution depend mainly on the low field strength of Na⁺ ions substituting for CaO even though the end groups occurring in the glasses increased. The variation in properties of the glasses containing SrO and BaO, some of which were substituted by Na₂O, could be explained by differences in masses, field strength and polarizability between the Na⁺ ions and the alkaline-earth ions due to a small variation in the structure of the glasses despite Na₂O substitution.     

Vapor phase epitaxy of pure VO2 and V1−xCrxO2

The vapor phase epitaxy of thin epilayers of VO₂ and V_1−xCrxO₂ on TiO₂ transparent substrates is described. Chemical vapor deposition occurs by reacting a (VOCL₃/CrO₂Cl₂/H₂O/H₂) mixture at about 800°C using argon as a carrier gas. The preparation of pure VO₂ requires special care to make it homogeneously stoichiometric and to obtain steep concentration profiles at the TiO₂/VO₂ interface. Layers were obtained which had electrical and optical properties comparable to the best bulk crystals grown by other techniques. Homogeneous solid solutions of V_1−xCr_xO₂ epilayers were also grown for the first time in the range o < x < 0.17. Chromium concentration and homogeneity were determined by electron microprobe analysis. The separation coefficient k was also found to vary with x. It is close to unity below x = 0.001 and above this value Cr is incorporated more easily. High quality heteroepitaxial layers (1 cm² area, 1 to 30 μm thickness) of V_1−xCr_xO₂ have for the first time allowed the measurement of the optical absorption coefficient.     

Elastic properties of GexAsySe100−x−y glasses

The elastic properties of Ge_xAs_ySe_100−x−y (0x30; 10y40) glasses have been studied. The results were analyzed in terms of the dependence on the theoretical mean coordination number (mean number of covalent bonds per atom) m (m=2+(2x+y)×0.01). Three ranges of m (2.1m2.51, 2.51<m2.78, 2.78<m3) were revealed, where different dependencies of elastic moduli (Young’s modulus, shear modulus) and Poisson’s ratio of glasses on m were observed.     

Compositional dependence of the optical gap in Ge1−xSx, Ge40−xSbxS60 and (As2S3)x(Sb2S3)1−x non-crystalline systems

An attempt is made to calculate the compositional dependence of the optical gap (E_g) in Ge_1−xS_x, Ge_40−xSb_xS₆₀ and (As₂S₃)_x(Sb₂S₃)_1−x non-crystalline systems in an alloy-like approach. From the comparison of both the experimental dependence of E_g and the calculated ones using the Shimakawa relation [E_{g AB} = YE_{g A} + (1−Y)E_{g B}] it is assumed that this equation is useful for such systems or parts of the systems which behave like almost ideal solutions.     

Li conductivity in lithium niobate: silica glasses

Glasses of composition 65 mol% LiNbO₃:: 35 mol% SiO₂ have been shown to be Li⁺ ion conductors with a conductivity at 200°C > 1 × 10⁻⁵ (η cm)⁻¹ and an activation energy of 0.54 eV. The addition of approximately 0.1 mol% Fe₂O₃ leads to an enhancement of conductivity to ≈10⁻³ (η cm)⁻¹ at 200°C and an activation energy of 0.67 eV. The effect of Fe is shown to be in the control of microstructure in the glass, with Fe₂O₃ concentrations < 1 mol% acting as a grain growth inhibitors and larger concentrations acting as a nucleating agents. A model for this process based on the expected stoichiometry of the melt and the effect of Fe²⁺ and Fe³⁺ in charge compensation is in excellent agreement with experimental data from electron spin resonance.     

Mössbauer studies on some glasses and crystals in the Na2O---Fe2O3---SiO2 system

Mössbauer absorption measurements have been made at room temperature on ⁵⁷Fe in iron sodium silicate glasses containing 3–15 mol% Fe₂O₃ and various iron alkali silicate crystals in order to study the state of iron in these glasses. The spectra of all the glasses gave one doublet with a quadrupole splitting varying from 0.73–0.78 mm s⁻¹, while those of Na₂O · Fe₂O₃ · 4 SiO₂ and 5 Na₂O · Fe₂O₃ · 8 SiO₂ crystals showed much smaller quadrupole splitting, 0.28 mm s⁻¹ and 0.10 mm s⁻¹, respectively, and an asymmetrical doublet of much narrower linewidth. When sodium was replaced by other alkali metals of larger size, such as K and Cs, in MFeSi₂O₆ and MFeSi₃O₈ crystals, the quadrupole splitting became wider and approached to 0.73 mm s⁻¹. Such a variation was not observed for glasses. These results suggest that a larger number of non-identical sites exist in iron sodium silicate glasses than in the corresponding crystals.     

Non-linear As(P) incorporation in GaAs1−yPy on GaAs and InAs1−yPy on InP

We find anion incorporation into both GaAs_1−yP_y on GaAs and InAs_1−yP_y on InP during gas source molecular beam epitaxy (GSMBE) is not linearly related to the hydride gas fluxes within our reactor. The deviation from an ideal model, i.e., y = ƒ_P/(ƒ_P+ƒ_As), where As(P) is the flux of AsH₃ (PH₃), can be as large as a factor of two. GaAsP exhibits the largest degree of nonlinearity and incorporation is found to depend quadratically on the fluxes over a wide range of flux ratio. Significant deviations are also found for InAsP; however, anion incorporation can be modeled with y = ƒ_P/(ƒ_P+βƒ_As).     

XAS study of lanthanum coordination environments in glasses of the system K2O---SiO2---La2O3

The La L₁ and L₃ XANES and L₃ EXAFS have been investigated for the series of glasses 10K₂O---50SiO₂---x La₂O₃ (x = 1, 5, 10) and (10 − x)K₂O---40SiO₂−(x/3)La₂O₃ (x = 7.5, 5, 2.5) and model compounds La₂O₃, LaAlO₃, LaPO₄, La₂NiO₄, La₂CuO₄ and La(OH)₃. An edge resonance at 25 eV above the L₁ edge in the glass spectra is concentration-dependent, decreasing in intensity with increasing lanthanum concentration. The 2s → nd forbidden transition increases with La₂O₃ concentration, indicating a reduction in the ‘average’ site symmetry of the first coordination shell of La. Mapping _X(k) space, which is a new and promising technique, was employed to extract bond distance, coordination number and thermal parameters from the EXAFS. By this method, one calculates the complete _X(k) space a function of all physically reasonable values of the adjusted parameters in all possible combinations. The advantage in this method is the assurance of a global minimum. Bond lengths were comparable to those obtained by Fourier transforming the phase corrected EXAFS. The values are 2.42 Å (± 0.03 Å) for La---O. The coordination numbers (N ≤ 7 ± 1.5) were derived by mapping and comparison to the published structures for other La compounds. _X(k) mapping is compared with least-squares fitting the data, and the correlation between the Debye-Waller factor and coordination number is also discussed.     

An infrared study of crystallization in sodium-disilicate glasses containing iron oxides

The infrared absorption spectra of sodium-disilicate glasses containing various amounts of Fe₂O₃ ([Na₂O · 2 SiO₂]_1−x [Fe₂O₃]_x, where X = 0.05, 0.1 and 0.2) were investigated in the wavenumber range from 200–2000 cm⁻¹. The addition of Fe₂O₃ to the sodium-disilicate glass does not seem to introduce any new absorption band as compared with the spectrum of a pure sodium-disilicate glass; nevertheless, a general shift of the existing absorption bands toward lower wavenumbers is observed. The amount of shift is, in fact, proportional to the content of Fe₂O₃ in the glass. This observation is consistent with the recently proposed structural model for the bonding of Fe³⁺ ions in the iron-sodium-silicate glass system.

Annealing of 20 mol% iron oxide glasses at 550 and 580°C produced an extra sharp infrared absorption peak at about 610 cm⁻¹ wavenumber. This new peak is believed to be related to the crystallized particles of the glass as concluded from both a scanning electron micrograph and an electron diffraction pattern.     

Low-temperature growth of epitaxial layers of ZnSe1−xTex solid solutions

The layers of ZnSe_1−xTe_x (0 < x < 1.0) solid solutions have been grown by liquid-phase epitaxy in a closed tube at 620–680 °C. Zinc chloride served as a solvent. ZnTe and ZnSe crystals were used as sources and substrates with orienting surfaces (110) and (111) for ZnSe and (110) for ZnTe. The composition of the grown layer was specified by the relative content of the ZnSe and the ZnTe in the solution and was controlled by X-ray analysis. The position of the exciton bands in the photoluminescence spectra of ZnSe_1−xTe_x over the interval 0.3 < x < 1.0 is in agreement with the free exciton energies calculated for these compositions. Relatively low-ohmic (of about 10² Ω cm) epitaxial layers of ZnSe_1−xTe_x solid solutions were grown.     

Elastic constant anomaly in Fe80−xMoxB20 metallic glasses

The extensional sound velocities V_E of Fe_80−xMo_xB₂₀(x = 6, 7, 8) metallic glasses have been measured between 100 and 600 K in a saturating magnetic field. Young's modulus (E = _E², = density) shows anomalous temperature dependence at and below the magnetic transition temperature of each glass studied. These anomalies are interpreted as arising from the change of long-range spin coupling energy at the Curie temperature in a molecular field approximation. Comparison is made with similar effects in other crystalline and non-crystalline magnetic materials.     

Diluted and non-diluted ferric ions in borate glasses studied by electron paramagnetic resonance

Electron paramagnetic resonance (EPR) spectra of lithium borate glass (1 - x)(0.63B₂O₃ · 0.37Li₂O) · xFe₂O₃, with x varying from 0.001 to 0.1, were measured at different microwave frequencies and temperatures. For low Fe³⁺ concentrations (Fe₂O₃ molar contents from 0.001 to 0.01), X-band EPR spectra, consisting of a g_{ef = 4.3} peak accompanied by a shoulder continuing down to g_{ef = 9.7}, are computer simulated on the basis of a ‘rhombic’ spin-Hamiltonian with Zeeman and fine-structure terms. A good fit to the experimental spectra for various Fe₂O₃ contents is observed with the same values of the spin-Hamiltonian parameters and assuming a Lorentzian lineshape and a linewidth increasing linealry with the concentration of Fe³⁺ ions. It is concluded that the spectrum is due to diluted Fe³⁺ ions in a relatively strong crystal field of orthorhombic symmetry, with largely distributed fine-structure parameters. From the concentration dependence of the line width, by extending to glasses a theoretical EPR linewidth expression derived for polycrystalline systems, the minimum distance between diluted Fe³⁺ ions is estimated as 4.9 Å. A diluted state of Fe³⁺ ions in the glass network in this range is also confirmed by the temperature dependence of the g_ef = 4.3 resonance which follows a Curie law. For intermediate concentrations of Fe³⁺ ions (Fe₂O₃ molar contents from 0.01 to 0.1), the width of the g_ef = 4.3 line is proportional to the square root of concentration, still indicating dipolar interactions. On the other hand, the microwave frequency dependence of a broad g_ef ≈ 2 line, which coexists at these concentrations with the g_ef = 4.3 line, shows that the former line is due to pairs or small clusters of exchange-coupled Fe³⁺ ions. The temperature dependence of the g_ef ≈ 2 line intensity in 0.1 mol Fe₂O₃ glass is consistent with a more antiferromagnetic character by comparison with the 0.05 mol Fe₂O₃ glass, which is attributed to an appearance, at higher Fe₂O₃ contents, of iron-containing microclusters not incorporated in the random glass network, with smaller distances between the paramagnetic ions. These microcluster are probably the origin of a new narrow line superposed with the broad g_ef ≈ 2 line in the low-temperature EPR spectra.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.     

NdxLa2−xCaB10O19: Synthesis and characterization

Solid solutions of Nd_xLa_2−xcaB₁₀O₁₉ with different Na³⁺ concentration have been synthesized by substituting Nd ³⁺ for La³⁺ in La₂CaB₁₀O₁₉ Powder X-ray diffraction analysis shows that Nd³⁺ is easy to incorporate into the crystal. Single crystal nd_xLa_2−xCaB₁₀O₁₉ (NLCB) in centimeter size has been grown by Kyropoulos method. The crystal has strong absorption around 580nm and 805nm. The fluorescence spectra indicate that there is an energy transition at 1.06μm. And the SHG of NLCB is about the twice as that of KDP. These favorable features make NLCB a candidate for laser NLO multifunctional materials.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Crystal growth and characterization of the CMR compound La1.2(Sr,Ca)1.8Mn2O7

High-quality centimeter-sized single crystals of La_1.2Sr_1.8−yCa_yMn₂O₇ (0.0y0.2) were successfully grown using a floating zone method associated with an image furnace. We present the growth conditions together with a characterization of the single crystals by means of optical and electron microscopy, EDX and ICPAES analysis, DTA-TGA measurements and redox titration, X-ray powder diffraction, Laue X-ray back-reflection and neutron diffraction. We also stress the main aspects of the complex thermodynamical and kinetic behaviors of these compounds.