BaBPO5晶体的生长研究

本文采用顶部籽晶高温溶液法,以BPO4-NaF为助熔剂,生长了BaBPO5单晶.生长参数:液面以下温度梯度为1.5℃/cm,液面上温度梯度为10℃/cm,晶体旋转速度30r/min,降温速率0.5-1℃/d,可获得尺寸为30mm×20mm×15mm的BaBPO5单晶.测定了所获单晶及其挥发物的X射线粉末衍射图谱,讨论了助熔剂对BaBPO5晶体生长的影响和该晶体的物化性能.     

高温溶液中ZnO的析晶行为与晶体生长研究

采用MoO3、V2O5和PbF2为助熔剂,在坩埚下降法生长炉中研究了ZnO的析晶行为和晶体生长.结果表明,对于M0O3-ZnO高温溶液体系,下降或降温过程中首先析出ZnO,但随着温度继续下降,析出了ZnMoO4晶体;对于V2O5-ZnO体系,通气速率为1.5 L/min时底部出现5mm厚的绿色ZnO多晶,无法获得单晶;对于PbF2-ZnO体系,自发成核获得了10 mm × 10 mm×0.7 mm的ZnO晶体薄片,在2 L/rain通气速率下诱导成核生长出φ25mm×5 mm的ZnO单晶.     

紫外非线性光学晶体三硼酸铯的生长和性能

采用泡生法和提拉法生长出三硼酸铯(化学式CsB3O5,简称CBO)晶体,研究了晶体生长工艺条件及晶体生长形态.泡生法生长的CBO晶体的尺寸为40mm×25mm×25mm;生长过程中晶体转速为10～20r/min,降温速率为0.1～0.2℃/d.用提拉法生长出20mm×30mm的CBO晶体;生长过程中液面温度梯度为60℃/cm,提拉速度为8mm/d.在生长过程中Cs2O的挥发速度大于B2O3的挥发速度.CBO单晶的晶面由[011]斜方柱和[010]斜方柱单形组成,属于[011]单形是4个较大的面,属于[101]单形是4个较小的三角形晶面.CBO在紫外波段具有较大的有效非线性光学系数.利用CBO进行Nd∶YAG激光和频获得了高转换率的波长355nm及266nm相干光输出.     

LiNbO3晶体的坩埚下降法生长

通过选择合适的原料配比(Li2O 48.6mol;,Nb2O5 51.4mol;),控制固液界面处的温度梯度为20～40℃/cm,晶体生长速度为0.6～1.5mm/h,采用密闭条件下的坩埚下降法工艺成功地生长出了具有良好光学均匀性的完整LiNbO3单晶.用X射线粉末衍射表征获得的LiNbO3晶相,讨论了若干工艺条件对晶体组分与质量的影响.测定了未密闭条件下生长的LiNbO3晶体不同部位样品的紫外可见光谱,发现其吸收边沿生长方向发生红移,并讨论了产生此现象的原因.     

快速生长大尺寸KDP单晶

用传统降温法生长了大尺寸KDP单晶,生长速度一般在1～2 mm/d,周期长,风险大.本文采用"点籽晶"快速生长法多次成功生长出了200 mm级的大尺寸KDP单晶,晶体生长速度达到20 mm/d,晶体生长正常.同时,摇摆曲线表明快速生长的晶体有着很好的结构完整性.     

碘化钾单晶的非真空密闭坩埚下降法生长

本文报道了KI单晶在非真空密闭条件下的坩埚下降法生长.以经充分干燥的高纯KI多晶为原料,将KI多晶料密封于套层铂坩埚中,添加少量活性碳粉末,可避免碘化物熔体的氧化与挥发,从而在非真空条件下实现KI单晶的坩埚下降法生长.在晶体生长过程中,炉体温度调节于750～770 ℃,固液界面温度梯度为30～40 ℃/cm,坩埚下降速率控制为1～2 mm/h,成功生长出尺寸为φ25 mm×50 mm的透明完整KI单晶.采用XRD、DTA-TG、透射光谱、荧光光谱对所获KI单晶进行了测试表征,结果表明该单晶具有良好的光学均匀性,在450～2500 nm波长范围的光学透过率达70;以上,其光学吸收边位于280 nm左右;在266 nm脉冲光激发下,该单晶具有397 nm峰值波长的荧光发射.     

Cr,Yb,Ho:YAGG可调谐激光晶体生长及开裂研究

本文采用提拉法生长了Cr,Yb,Ho:YAGG可调谐激光晶体,并从理论上讨论了热应力、提拉速度、晶体转速和降温速率等因素对晶体开裂的影响,最后给出了掺铬、镱和钬钇铝镓石榴石激光晶体生长的最佳工艺条件:温度梯度为0.5℃/mm,提拉速度1～2mm/h,晶体转速20～40r/min,冷却速率不超过20℃/h.     

SrTiO3单晶体生长过程中的溢流问题

本文以氯化锶和氯化钛为原料,采用控制水解法制备SrTiO3原料粉末,使用焰熔法生长了SrTiO3单晶体.晶体生长参数为:原料粉末粒度为-200+250目,炉膛气氛的氢氧比H/O为6.00,生长速度为12mm/h,获得了直径30mm,长60mm的单晶.晶体生长过程中,晶体顶部熔体的溢流是妨碍获得大尺寸完整晶体的一个最主要的问题.本文详细讨论了SrTiO3单晶体生长过程中的溢流的成因和解决办法.     

坩埚下降法生长白宝石晶体的研究

本文报道了坩埚下降法生长大尺寸白宝石单晶.我们使用大尺寸异型钼坩埚,高纯氧化铝原料,在中性气氛下,结晶区温度梯度为25～30℃/cm,生长速度为0.8～1.8mm/h,生长方向选C面[0001]取向,成功生长出直径80mm,高度90mm的完整透明的白宝石单晶,在300～5500nm范围内,其光学透过率均在80;以上.实验中采用高性能保温材料使生长过程所需加热功率由20kW下降到15kW,能耗降低达25;;采用双回路加热系统,提高温场稳定性,缩短晶体生长周期.晶体的主要缺陷为顶部(生长后期)出现有5～10mm淡黄色色带(经在氧化性气氛中退火后已消除)和底部有细丝状条纹.     

以H2SO4为添加剂降温法生长PET晶体

采用H2SO4作为季戊四醇(PET)晶体生长的添加剂,用溶液降温法在5 L生长槽内生长出45 mm×45 mm×40 mm 的PET单晶,生长速度达到1.5 mm/d,比纯态溶液生长晶体的速度提高2倍.采用XRD、FT-IR和TG等测试方法对晶体进行表征,实验表明添加剂H2SO4不影响晶体的结构完整性.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

New zeotype borophosphates with chiral tetrahedral topology: (H)0.5M1.25(H2O)1.5[BP2O8]·H2O (M = Co(II) and Mn(II))

Two new isostructural open‐framework zeotype transition metal borophosphate compounds, (H)_0.5M_1.25(H₂O)_1.5[BP₂O₈]·H₂O (M = Co(II) and Mn(II)) were synthesized by mild hydrothermal method. The structure of compounds were characterized by single‐crystal X‐ray diffraction which have ordered, alternating, vertex‐sharing BO₄, PO₄, and (MO₄)OM(H₂O)₂ groups with hexagonal, P 6₁ 2 2 (No 178) space group and unit cell parameters for Co a = 9.4960(6) Å, c = 15.6230(13) Å, for Mn a = 9.6547(12) Å, c = 15.791(3) Å, Z = 1 for both of them. TGA/DTA analysis, IR spectroscopy were used for characterization. Magnetic susceptibility measurements for both of the compound indicate strong antiferromagnetic interaction between metal centers. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Solubility of Ag2O into the Na2O–B2O3–Al2O3 system

The solubility of Ag₂O was measured for the Na₂O–B₂O₃ and Na₂O–B₂O₃–Al₂O₃ system with the rotating crucible method and static method, respectively, under air atmosphere at temperatures ranging from 1273 to 1423 K. The contamination of melts from crucibles could be avoided by the rotating crucible method, with which it became possible to measure the solubility of Ag₂O for the Na₂O–B₂O₃ system above the melting point of Ag for the first time. It was found that the addition of Na₂O decreases the solubility of Ag₂O while the addition of Al₂O₃ had little effect on the solubility. The effect of Na₂O and Al₂O₃ on the solubility of Ag₂O is expressed by interaction coefficients and is analyzed in terms of the basicity of melts. The solubility of Ag₂O in Na₂O–B₂O₃–Al₂O₃ melts increased with increased temperature. This phenomena was explained by a small enthalpy change in oxidation of silver.     

Selinidin: Crystal structure generated by C–H···O, C–H···π and π-π interactions

The title compound, 9,10-dihydro-8,8-dimethyl-2-oxo-2H,8H-benzo[1,2-b:3,4-b']dipyran-9-yl-2-methyl-2-butenoate, C₁₉H₂₀O₅, was isolated from the roots of Selinum vaginatum. The compound crystallizes into monoclinic space group P2 ₁ with unit cell parameters: a = 12.830(2) Å, b = 9.041(1) Å, c = 14.983(1) Å, β = 95.09(1)°, Z = 4. The crystal structure has been determined using direct methods and refined by full-matrix least-squares to a final R value of 0.0529 for 3142 observed reflections. There are two independent molecules, A and B, per asymmetric unit. In both the molecules, the coumarin nucleus is planar. However pronounced differences are observed in the conformation of dihydropyran ring which has a half-chair conformation with an 8β-9α orientation in molecule A and is intermediate between half-chair and sofa in molecule B. Differences also occur in the conformation of the 2-methylbutenoyloxy side chain at C9 due to the different geometry of C–H···π interactions in molecules A and B. Molecules A and B are connected by π–π interactions between their coumarin fragments forming dimers. The dimers interact through C–H···O and C–H···πhydrogen bonds.     

Chromene and Imidazole Based D-π-A Chemosensor Preparation and Its Anion Responsive Effects

We have designed and synthesized the colorimetric chemosensor through the reactions of 2-(4H-chromen-4-yildene)malonitrile and 4-imidazolecarboxaldehyde. Due to its well conjugated D-π-A system and the existence of NH- fragment in structure, we expected that the chemosensor can detect anion using NH- fragment in the imidazole moiety of the structure. In this regard, UV-Vis absorption spectra were measured to investigate sensing properties of the probe toward different anions in DMSO. This chemosensor can detect both fluoride and cyanide ion with absorption change in intensity. In addition, pH sensing property was also investigated upon the addition of hydroxide ion. These properties are related to the deprotonation effect. The ICT system in this molecule was also observed by the computational approach using Material Studio 4.3 package.     

电子显微分析在表征纳米晶体化学组分中的应用

纳米材料的化学组分及含量影响其光、电、声、热、磁等物理性能,电子显微分析是表征纳米晶体化学组分的重要方法之一.本文综述了X-射线能谱(EDS)、X-射线波谱(WDS)、电子能量损失谱(EELS)和选区电子衍射(SAED)等现代电子显微分析技术在表征纳米晶体化学组分、形貌、尺寸和结构等方面的应用及其研究进展,并比较了这些分析方法存在的差异,提出了其应用中存在的不足及今后的研发方向.     

Considerations on the structure and physical properties of B2O3-SiO2 and GeO2-SiO2 glasses

Data of density, refractive index and thermal expansion coefficient for B₂O₃-SiO₂ and GeO_2-SiO₂ glasses have been analyzed. The volumes of the structural units are the same found for the vitreous B₂O₃, GeO₂ and SiO₂. The volume of any structural unit is constant over the entire composition region of the glass system. The same has been found for the differential refraction and unit refraction of the structural units in these glasses. Different features are observed for the differential expansion of the structural units. There is a considerable change with composition in the differential expansion of BO₃, GeO₄ and SiO₄ units. The effect is attributed to a change in the asymmetry of vibrations with the number of Si-O-B or Si-O-Ge linkages in the matrix. The thermal expansion coefficient is mainly determined by the contribution of B₂O₃ or GeO₂ in the concerned glasses.