Thermal expansion of glass–ceramics in the system BaO/Al2O3/B2O3

Glasses in the system BaO/Al₂O₃/B₂O₃ with and without the addition of platinum were melted. In one sample series, the BaO-concentration was varied while the ratio [Al₂O₃]/[B₂O₃] was kept constant. In another sample series, the [BaO]/[Al₂O₃]-ratio (= 0.9) was kept constant and the B₂O₃ concentration was varied. The samples were thermally treated at 720 °C for 24 h and subsequently at 780 °C for 4 h. In most thermally treated samples, the crystalline phase BaO · Al₂O₃ · B₂O₃ occurred. At some compositions, the platinum-doped samples showed larger concentrations of the crystalline phases. The most remarkable property of the obtained glass–ceramics is their zero or negative thermal expansion coefficient. Here, notable differences were observed: samples with fine grained microstructures showed thermal expansion coefficients approximately zero up to temperatures of around 80 °C. By contrast, samples with coarser microstructures and large spheroidal crystals exhibit negative expansion coefficients up to temperatures of around 280–375 °C. The thermal expansions of these samples were close to those of the mean thermal expansion of the unit cell of the BaO · Al₂O₃ · B₂O₃ phase. The thermal expansion of the fine grained samples was approximately equal to that of the crystallographic a-axis of the BaO · Al₂O₃ · B₂O₃ phase.     

Effect of B2O3 addition on the thermal properties and density of barium phosphate glasses

Variations in glass transition temperature, onset of crystallization, thermal expansion coefficient, density and molar volume with B₂O₃ concentration were studied in a series of xB₂O₃–(100 − x)Ba(PO₃)₂ glasses with 0–10 mol% B₂O₃. DTA analysis and isothermal treatments for powdered glass samples reveal that ⩾7.5 mol% B₂O₃ addition suppresses surface crystallization during softening process. Raman spectroscopy suggests that the properties are related to the glass structure consisting of PO₄ Q² units with diborate and PO₄–BO₄ groups.     

Non-isothermal crystallization kinetic studies on MgO–Al2O3–SiO2–TiO2 glass

Thermal stability and crystallization kinetics of the glass 21% MgO, 21.36% Al₂O₃, 53.32% SiO₂ and 4.11% TiO₂ (mol%) has been studied using differential thermal analysis (DTA), dilatometry and X-ray diffraction (XRD). Glass in both bulk and frit forms were produced by melting in platinum crucible at 1600 °C for 1–2 h. From variation of DTA peak maximum temperature with heating rate, the activation energies of crystallization were calculated to be 340 kJ mol⁻¹ and 498 kJ mol⁻¹ for first and second crystallization exotherms, respectively. Crystallization of bulk glass was carried out at various temperatures and for different time durations in the range of 850–1000 °C. The influence of the addition of TiO₂ on the crystallization sequence of the glass was experimentally determined and discussed.     

Thermal and optical properties of CuO–BaO–B2O3–P2O5 glasses

CuO-doped barium borophosphate glasses in a series of xCuO–(45 − x)BaO–10B₂O₃–45P₂O₅ in molar ratio with x = 0–15 mol% were prepared by a melt-quenching technique. All the glasses had excellent thermal stability against crystallization. Glass transition temperature, thermal expansion coefficient and molar volume decrease with increasing CuO concentration. The linear relationship between the absorption coefficient and CuO concentration exists for a peak wavelength in the transitions of ²A_1g → ²B_1g, ²B_2g → ²B_1g, ²E_g → ²B_1g. The relationship between the properties and glass structure evaluated by Raman spectroscopy is discussed.     

Thermal properties and glass formation in the SiO2–B2O3–Bi2O3–ZnO quaternary system

Lead-free glasses in the SiO₂–B₂O₃–Bi₂O₃–ZnO quaternary system were studied. The glass formation region, as determined by XRD patterns of bulk samples, was limited to glasses having more than 40 mol% of the glass-forming oxides SiO₂ and B₂O₃. Crystalline phases of Zn₂SiO₄ (willemite) were detected in compositions of 30SiO₂ · 10B₂O₃ · 20Bi₂O₃ · 40ZnO and 20SiO₂ · 10B₂O₃ · 25Bi₂O₃ · 45ZnO. Glass transition temperatures (T_g), dilatometric softening points (T_d) and linear coefficients of expansion in the temperatures range of 25–300 °C (α_25–300) were measured for subsystems along the B₂O₃ join of 10, 20 and 30 mol%. For these subsystems, T_g ranged from 411 to 522 °C, and T_d ranged from 453 to 563 °C, both decreasing with increasing Bi₂O₃ content. The measured α_25–300 ranged from 53 to 95 × 10⁻⁷ °C⁻¹, with values increasing with increasing Bi₂O₃ content. The ZnO content had the opposite effect to the Bi₂O₃ content. It appears that Bi³⁺ acts as a glass-modifier in this quaternary system.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Characterization of B2O3 and/or WO3 containing tellurite glasses

Characterization of B₂O₃ and/or WO₃ containing tellurite glasses was realized in the 0.80TeO₂–(0.20 ? x)WO₃ ? xB₂O₃ system (0 ≤ x ≤ 0.20 in molar ratio) by using differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectrometry techniques. Glasses were prepared with a conventional melt-quenching technique at 750 °C. To recognize the thermal behavior of the glasses, glass transition and crystallization temperatures, glass stability value, glass transition activation energy, fragility parameter were calculated from the thermal analyses. Density, molar volume, oxygen molar volume and oxygen packing density values were determined to investigate the physical properties of glasses. Fourier transform infrared spectra were interpreted in terms of the structural transformations on the glass network, according to the changing B₂O₃ and/or WO₃ content. Crystallization behavior of the glasses was investigated by in situ X-ray diffraction measurements and microstructural characterization was realized by scanning electron microscopy and energy dispersive X-ray spectrometry analyses.     

In2O3 and tin-doped In2O3 nanocrystals prepared by glass crystallization

Glasses in the system Na₂O/B₂O₃/Al₂O₃/In₂O₃/(SnO₂) were melted and subsequently tempered in the range from 540 to 700 °C. This led to the crystallization of In₂O₃, besides also NaBO₂ and Na₂Al₂B₂O₇ were formed. The crystallite sizes were in the range from 12 to 34 nm, depending on the temperature of thermal treatment, as calculated from XRD-line broadening. Crystal sizes determined by TEM were in the same range. Particle size histograms show a narrow crystal size distribution. After crystallization, the glass matrices and the non indium-containing crystalline phases were dissolved in diluted acetic acid. Spectra of the obtained suspensions containing tin-doped In₂O₃ nanocrystals exhibited a sharp UV-cut off, high transmission in the visible range and strongly decreasing transmission at wavelengths >1000 nm.     

Preparation and characterization of CuO doped Bi2O3–B2O3–BaO–ZnO glass system for transparent dielectric layer

The electrical, thermal, optical, and morphological properties of CUO doped Bi₂O₃–B₂O₃–BaO–ZnO glasses were studied as a PbO-free, low firing transparent dielectric layer for plasma display panels (PDP). CuO improved the transmittance of Bi₂O₃–B₂O₃–BaO–ZnO by up to 84% in the visible region, eliminating a yellowish color typical of Bi₂O₃–B₂O₃–BaO–ZnO. A slight absorption within the near infrared (NIR) region was also observed. The glass transition temperature (T_g), thermal coefficient of expansion (TCE), and root-mean square (rms) roughness of 0.005 wt% CuO doped Bi₂O₃–B₂O₃–BaO–ZnO were found to be 455 °C, 81.4 × 10⁻⁷/K, respectively, and 162 ± 14 Å, which satisfied the requirements for a transparent dielectric layer for PDP application.     

Incorporation of B2O3 in CaO-SiO2-P2O5 bioactive glass system for improving strength of low-temperature co-fired porous glass ceramics

Bioactive glass ceramics (BGCs) have different rates of biodegradation and mechanical properties depending on their chemical compositions and sintering temperatures. The present study was aimed to develop the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ bioactive glasses (BG-B_x, X = 0, 10, 20) potentially for improving the mechanical properties of BGCs via low-temperature co-fired process. The B₂O₃-free BG-B₀ shrunk well at ~ 726 °C and melted at over 1050 °C, while the onset shrinking and melting temperatures of the 20 mol% B₂O₃-doped BG-B₂₀ was lowered to ~ 648 °C and ~ 952 °C, respectively. The BG-B₂₀ thermally treated at 850–950 °C was transformed into wollastonite and calcium borate, and crystallization decreased the kinetics but did not inhibit the development of hydroxyapatite on their powder and disc surface when immersed in simulated body fluid. The in vitro degradation in Tris buffer confirmed that the degradation rate markedly increased with increasing boron content in BG-B_x. The compressive strength and flexural strength of the 10% BG-B₂₀-reinforced 45S5 porous BGC sintered at 850 °C was nearly four times than that of 45S5 porous constructs. These studies suggest that the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ system is a promising biomaterial and potential low temperature co-fired aid for improving the mechanical and biological properties of porous BGCs.     

Structural properties of Cr2O3–Fe2O3–P2O5 glasses,Part I

The structural properties of xCr₂O₃–(40 − x)Fe₂O₃–60P₂O₅, 0 ⩽ x ⩽ 10 (mol%) glasses have been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The Raman spectra show that the addition of up to 5.3 mol% Cr₂O₃ does not produce any changes in the glass structure, which consists predominantly of pyrophosphate, Q¹, units. This is in accordance with O/P ≈ 3.5 for these glasses. The increase in glass density and T_g that occurs with increasing Cr₂O₃ suggests the strengthening of glass network. The Mössbauer spectra indicate that the Fe²⁺/Fe_tot ratio increases from 0.13 to 0.28 with increasing Cr₂O₃ content up to 5.3 mol%, which can be related to an increase in the melting temperature from 1423 to 1473 K. After annealing, the 10Cr₂O₃–30Fe₂O₃–60P₂O₅ (mol%) sample was partially crystallized and contained crystalline β-CrPO₄ and Fe₃(P₂O₇)₂. The SEM and AFM micrographs of the partially crystallized sample revealed randomly distributed crystals embedded in a homogeneous glass matrix. EDS analysis indicated that the glass matrix was rich in Fe₂O₃ (39.6 mol%) and P₂O₅ (54.9 mol%), but contained only 5.5 mol% of Cr₂O₃. These results suggest that the maximum solubility of chromium in these iron phosphate melts is 5.5 mol% Cr₂O₃.     

Evolution of nanocrystalline BaBi2Nb2O9 in Li2B4O7–BaO–Bi2O3–Nb2O5 glass system

Transparent glasses and glass nano crystal composites (GNCs) of various compositions in the system (100 − x)Li₂B₄O₇–x(BaO–Bi₂O₃–Nb₂O₅) (where x = 10, 20, and 30 in molar ratio) were fabricated via splat-quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses. X-ray powder diffraction and transmission electron microscopic (TEM) studies confirmed the formation of layered perovskite BBN via a fluorite like phase. TEM studies revealed the presence of 10 nm sized spherical crystallites of fluorite like BaBi₂Nb₂O₉ phase in the glassy matrix of Li₂B₄O₇ (LBO). The influence of composition on the dielectric and the optical properties (transmission, optical band gap) of these samples has been investigated.     

The effect of fluoride on the Fe2+/Fe3+-redox equilibrium in glass melts in the system Na2O/NaF/CaO/Al2O3/SiO2

Liquids with the base compositions (16 − x/2)Na₂O · xNaF · 10CaO · 74SiO₂ (x = 0, 1, 3, and 4) and (10 − x/2) · Na₂O · xNaF · 10CaO · yAl₂O₃ · (80 − y)SiO₂ (x = 0, 1, 3, 5 and y = 5 and 15) doped with 0.25 mol% Fe₂O₃ were studied by means of square-wave voltammetry in the temperature range from 1000 to 1500 °C. With increasing temperature, the redox equilibria were shifted to the reduced state. Also while increasing the alumina concentration, the Fe²⁺/Fe³⁺-redox equilibrium is shifted to the reduced state. In the soda-lime–silica melt the addition of fluoride shifts the equilibrium to the oxidized state, while in the aluminosilicate melts with 15 mol% Al₂O₃, the equilibrium is shifted to the reduced state. In the aluminosilicate melts with 5 mol% Al₂O₃, the equilibrium was not affected by the fluoride concentration. This is explained by the structure of the respective glass compositions.     

The effect of RO (R = Mg,Ca, Ba and Zn) on physical properties of Na2O/Al2O3/B2O3/SiO2 glasses for the preparation of gradient index micro lenses

Glasses in the system Na₂O–Al₂O₃–B₂O₃–SiO₂ doped with MgO, CaO, BaO or ZnO (concentrations: 2.5%–5 mol%) were melted from the raw materials and studied with respect to their densities, hydrolytic durabilities, crystal growth velocities, specific ionic conductivities, refractive indices, Abbe numbers and optical transmissions. The samples were ion exchanged in a NaNO₃/AgNO₃ salt melt in order to determine the Na⁺/Ag⁺ interdiffusion coefficients and the refractive indices, Abbe numbers and optical transmissions of the ion exchanged silver containing glasses. Glasses doped with ZnO are advantageous for the production of gradient index lenses due to their improved chemical durability and smaller crystal growth velocities at viscosities in the range of 10⁵–10⁶ dPa s. The optical properties of these glasses are similar to those of glasses without RO.     

Soda lime zirconia silicate glasses as prospective hosts for zirconia-containing radioactive wastes

Na₂O–CaO–ZrO₂–SiO₂ glass compositions with ZrO₂ contents of up to 20 mol% were melted. Up to 12.3 mol% ZrO₂ could be dissolved into the glasses. Melting temperatures ⩾1450 °C were required to remove seed and produce a melt that could be cast. Addition of ZrO₂ caused an increase in the glass transition and crystallization temperatures. Glasses crystallized at temperatures ⩾1050 °C with Keldyshite and Parakeldyshite (Na₂O · ZrO₂ · 2SiO₂) as the crystalline phases. Addition of up to 4.6 mol% ZrO₂ caused an increase in the hydrolytic resistance of the glass, with further additions having little effect. The suitability of these glasses as hosts for ZrO₂-containing radioactive wastes is discussed.     

Electrical properties of SrBi2(Nb0.7V0.3)2O9−δ in the SrO–Bi2O3–0.7Nb2O5–0.3V2O5–Li2B4O7 glass system

Glasses in the system (100 − x)Li₂B₄O₇–x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (where x = 10, 30 and 50, in molar ratio) were fabricated via melt quenching technique. The compositional dependence of the glass transition (T_g) and crystallization (T_cr) temperatures was determined by differential thermal analysis. The as-quenched glasses on heat-treatment at 783 K for 6 h yielded monophasic crystalline strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) in lithium borate (Li₂B₄O₇ (LBO)) glass matrix. The formation of nanocrystalline layered perovskite SBVN phase was preceded by the fluorite phase as established by both the X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The dielectric constants for both the as-quenched glass and glass–nanocrystal composite increased with increasing temperature in the 300–873 K range, exhibiting a maximum in the vicinity of the crystallization temperature of the host glass matrix. The electrical behavior of the glasses and glass–nanocrystal composites was characterized using impedance spectroscopy.     

The influence of Fe2O3 and B2O3 additions on the thermal properties,crystallization kinetics and durability of a sodium aluminum phosphate glass

A sodium aluminum phosphate glass, identified as a potential encapsulating phase for radioactive wastes, has been noted to be thermally unstable, crystallizing upon heat treatment to yield a variety of phases which may be detrimental to the longer term properties of the final wasteform. In an attempt to improve the thermal stability and overall resistance of this glass to crystallization, the influence of various oxide additions including Fe₂O₃ and B₂O₃ has been investigated. It has been shown that quite small additions of B₂O₃ are extremely effective in improving the stability, with ⩾2 mol% B₂O₃ almost completely suppressing crystallization whilst only marginally affecting the excellent chemical durability of the ternary glass, at least at the lower B₂O₃ concentrations. In contrast, addition of Fe₂O₃ or B₂O₃/Fe₂O₃ mixtures does not lead to significant improvements in the thermal stability, although durability relative to that of the ternary composition is improved significantly with increasing Fe₂O₃ content.     

ESR dosimeter based on P2O5–CaO–Na2O glass system

This paper presents the results of a study of thermal properties, solubility and response to ⁶⁰Co γ-rays by electron spin resonance of the P₂O₅–CaO–Na₂O glass system. The sample compositions were selected by fixing the P₂O₅ mol% content at 50 mol%, and varying the CaO mol% at 30 and 40 mol%. The spectrum is characterized by hyperfine doublet from ³¹P isotope (nuclear spin = 1/2), and its stability and response to the γ-ray dose were studied to establish the suitability of this glass as a γ-ray dosimeter.     

Laser induced modification on 40BaO–45B2O3–15TiO2 glass composition

This paper describes a study concerning the permanent modification of 40BaO–45B₂O₃–15TiO₂ (mol%) glass composition when irradiated by a continuous CO₂ laser beam. Three parameters of the permanent modification and crystallization processes induced by irradiation were studied: laser power, irradiation time and the presence of micrograins of β-BaB₂O₄ (β-BBO) crystalline phase on the glass sample surface prior to irradiation. The geometry of permanent deformation induced by irradiation depended mainly on the laser power and sample surface condition. Crystallization of the irradiated region was observed when laser power at around 0.72 W and an irradiation time of around 300 s were used. The structural characterization performed by micro-Raman and X-ray diffraction techniques showed the formation of only the BaTi(BO₃)₂ crystalline phase on the as-polished sample. On the other hand, when β-BBO microcrystals were homogeneously dispersed onto the glass surface, the formation of the β-BBO phase was induced. In this condition, the β-BBO becomes the main crystalline phase and presents a certain degree of texture.     

Square-wave voltammetry and impedance spectroscopy in iron-doped melts of the system Li2O/Al2O3/SiO2

Glass melts with the basic compositions xLi₂O · 15Al₂O₃ · (85 − x)SiO₂ (x = 8.5, 11, 13.5, 16 and 18.5) doped with 0.25 mol% Fe₂O₃ were studied by square-wave voltammetry and impedance spectroscopy at temperatures in the range from 1100 to 1600 °C. The square-wave voltammograms show a pronounced peak attributed to the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials which are equal to the standard potentials of the redox pair decrease linearly with the temperature. Impedance spectra measured could be simulated using an equivalent circuit attributed to a simple electron transfer reaction controlled by diffusion.