The effect of fluoride on the Fe2+/Fe3+-redox equilibrium in glass melts in the system Na2O/NaF/CaO/Al2O3/SiO2

Liquids with the base compositions (16 − x/2)Na₂O · xNaF · 10CaO · 74SiO₂ (x = 0, 1, 3, and 4) and (10 − x/2) · Na₂O · xNaF · 10CaO · yAl₂O₃ · (80 − y)SiO₂ (x = 0, 1, 3, 5 and y = 5 and 15) doped with 0.25 mol% Fe₂O₃ were studied by means of square-wave voltammetry in the temperature range from 1000 to 1500 °C. With increasing temperature, the redox equilibria were shifted to the reduced state. Also while increasing the alumina concentration, the Fe²⁺/Fe³⁺-redox equilibrium is shifted to the reduced state. In the soda-lime–silica melt the addition of fluoride shifts the equilibrium to the oxidized state, while in the aluminosilicate melts with 15 mol% Al₂O₃, the equilibrium is shifted to the reduced state. In the aluminosilicate melts with 5 mol% Al₂O₃, the equilibrium was not affected by the fluoride concentration. This is explained by the structure of the respective glass compositions.     

Square-wave voltammetry and impedance spectroscopy in tin doped melts with the compositions xNa2O · 15Al2O3 · (85 − x)SiO2 (x = 8.5, 11 and 16)

Glasses with the base compositions xNa₂O · 15Al₂O₃ · (85 ? x)SiO₂ (x = 8.5, 11 and 16) doped with 0.5 mol% SnO₂ were investigated by both square-wave voltammetry and impedance spectroscopy in the temperature range from 1300 to 1600 °C. Each recorded square-wave voltammogram exhibits a well pronounced peak attributed to the Sn²⁺/Sn⁴⁺-redox pair. Impedance spectra were measured in a frequency range from 0.1 to 10⁵ s^?1 as a function of the superimposed dc-potential and were simulated using an equivalent circuit taking into account the resistivity of the melt, the electrochemical double layer, a resistor attributed to a kinetically hindered electron transfer and a Warburg parameter which accounts for the diffusion process of Sn⁴⁺ and Sn²⁺ to and from the electrode. Additionally, two impedance elements, a resistor and a capacitance both attributed to adsorption processes were necessary to fit the impedance spectra.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Redox behavior and diffusion of copper in soda-lime-silica melts

Glasses with the base mol% composition xNa₂O · 10CaO · (90 ? x)SiO₂ with x = 10, 16, 20 and 26 were investigated at high temperatures using square-wave voltammetry. The recorded voltammograms exhibit two peaks. That at less negative or (depending on temperature and glass composition) even positive potential is attributed to the reduction of Cu²⁺ to Cu⁺, while that observed at more negative potential is caused by the reduction of Cu⁺ to metallic copper. For both redox steps, the peak potentials decrease linearly with temperature. Those of the composition with 10 mol% Na₂O show the most negative values. The diffusion coefficients can be fitted to Arrhenius equation. If referenced to the same viscosity, the diffusion coefficients decrease with increasing Na₂O-concentration. The effect of composition on the thermodynamics as well as on diffusivities is explained by the incorporation of the copper ions into the melt structure.     

Structural properties of Cr2O3–Fe2O3–P2O5 glasses,Part I

The structural properties of xCr₂O₃–(40 − x)Fe₂O₃–60P₂O₅, 0 ⩽ x ⩽ 10 (mol%) glasses have been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The Raman spectra show that the addition of up to 5.3 mol% Cr₂O₃ does not produce any changes in the glass structure, which consists predominantly of pyrophosphate, Q¹, units. This is in accordance with O/P ≈ 3.5 for these glasses. The increase in glass density and T_g that occurs with increasing Cr₂O₃ suggests the strengthening of glass network. The Mössbauer spectra indicate that the Fe²⁺/Fe_tot ratio increases from 0.13 to 0.28 with increasing Cr₂O₃ content up to 5.3 mol%, which can be related to an increase in the melting temperature from 1423 to 1473 K. After annealing, the 10Cr₂O₃–30Fe₂O₃–60P₂O₅ (mol%) sample was partially crystallized and contained crystalline β-CrPO₄ and Fe₃(P₂O₇)₂. The SEM and AFM micrographs of the partially crystallized sample revealed randomly distributed crystals embedded in a homogeneous glass matrix. EDS analysis indicated that the glass matrix was rich in Fe₂O₃ (39.6 mol%) and P₂O₅ (54.9 mol%), but contained only 5.5 mol% of Cr₂O₃. These results suggest that the maximum solubility of chromium in these iron phosphate melts is 5.5 mol% Cr₂O₃.     

Structural and magnetic investigations of Fe2O3–TeO2 glasses

A series of tellurite glasses containing Fe₂O₃ with the nominal composition x(Fe₂O₃)–(1−x)(TeO₂), where x = 0.05, 0.10, 0.15, and 0.20, have been synthesized and investigated using X-ray photoelectron spectroscopy (XPS) and magnetization techniques. The Te 3d core level spectra for all glass samples show symmetrical peaks at essentially the same binding energies as measured for TeO₂ indicating that the chemical environment of the Te atoms in these glasses does not vary significantly with the addition of Fe₂O₃. Furthermore, the full-width at half-maximum (FWHM) of each peak does not vary with increasing Fe₂O₃ content which suggests that the Te ions exist in a single configuration, namely TeO₄ trigonal bipyramid (tbp). The O 1s spectra are narrow and symmetric for all compositions such that oxygen atoms in the Te–O–Te, Fe–O–Fe and Te–O–Fe configurations must have similar binding energies. The analysis of the Fe 3p spectra indicates the presence of Fe³⁺ ions only, which is consistent with the valence state of the Fe ions determined from magnetic susceptibility measurements.     

Magnetic properties of the Mg2FeV3O11−x site-disordered vanadate

The magnetic properties of the Mg₂FeV₃O_11−x ternary vanadate, characterized by disorder between diamagnetic Mg²⁺ and high-spin Fe³⁺ ions, are studied using dc magnetization and electron paramagnetic resonance (EPR). The dc susceptibility shows antiferromagnetic interactions between Fe³⁺ spins with a Curie–Weiss temperature of Θ = −50(1) K, followed by spin-glass-like freezing at T_f ≈ 2.8 K, suggesting significant spin frustration. Temperature-dependent EPR measurements confirm the antiferromagnetic coupling of Fe³⁺ spins at high temperatures, while a distinct divergence is observed at T ≈ 50 K. This behavior is associated with the formation of spin clusters providing two different energy scales for the magnetic interactions. The magnetic response of Mg₂FeV₃O_11−x is similar to that of the Zn-analogue compound, though the observed differences of the implicated energy scales indicate that magnetic inhomogeneity depends on the extent of cation disorder.     

Mixed transition-ion effect in the glass system: Fe2O3-MnO-TeO2

In earlier studies on phosphate and tellurite glasses containing vanadium and iron oxides, non-linear variation of physical properties as functions of the ratios of the transition ions (V/V + Fe) were observed. The most striking effect was observed with electrical conductivity, where a 3 orders of magnitude reduction in conductivity was observed at a V/V + Fe ratio of ~ 0.4. The effect was termed Mixed Transition-ion Effect or MTE. In phosphate glasses, however, MTE was not observed when one of the transition ions was manganese. It was concluded that Mn does not contribute to conduction in these glasses. In the present study, we demonstrate a mixed transition ion effect in tellurite glasses containing MnO and Fe₂O₃ (xFe₂O₃(0.2 ? x) MnO0.8TeO₂ with x varying from 0 to 0.2). A maximum in the property at an intermediate composition (x = 8.5 mol%), was observed in DC resistivity, activation energy, molar volume etc. Mossbauer and optical absorption (UV–VIS–NIR) measurements were performed on these glasses and the transport mechanism has been identified to be hopping of small polarons between Fe^3 + (Mn^3 +) and Fe^2 + (Mn^2 +) sites.     

Thermal properties and glass formation in the SiO2–B2O3–Bi2O3–ZnO quaternary system

Lead-free glasses in the SiO₂–B₂O₃–Bi₂O₃–ZnO quaternary system were studied. The glass formation region, as determined by XRD patterns of bulk samples, was limited to glasses having more than 40 mol% of the glass-forming oxides SiO₂ and B₂O₃. Crystalline phases of Zn₂SiO₄ (willemite) were detected in compositions of 30SiO₂ · 10B₂O₃ · 20Bi₂O₃ · 40ZnO and 20SiO₂ · 10B₂O₃ · 25Bi₂O₃ · 45ZnO. Glass transition temperatures (T_g), dilatometric softening points (T_d) and linear coefficients of expansion in the temperatures range of 25–300 °C (α_25–300) were measured for subsystems along the B₂O₃ join of 10, 20 and 30 mol%. For these subsystems, T_g ranged from 411 to 522 °C, and T_d ranged from 453 to 563 °C, both decreasing with increasing Bi₂O₃ content. The measured α_25–300 ranged from 53 to 95 × 10⁻⁷ °C⁻¹, with values increasing with increasing Bi₂O₃ content. The ZnO content had the opposite effect to the Bi₂O₃ content. It appears that Bi³⁺ acts as a glass-modifier in this quaternary system.     

Bond character,optical properties and ionic conductivity of Li2O/B2O3/SiO2/Al2O3 glass: Effect of structural substitution of Li2O for LiCl

A glass of composition (20 ? x)Li₂O–xLiCl–65B₂O₃–10SiO₂–5Al₂O₃ where 0 ? x ? 12.5 wt% is prepared using the normal melt-quenching technique. The optical constants and electrical conductivity and their correlation are investigated, furnished and discussed with the substitution of Li₂O for LiCl. The mechanism of the optical absorption and the calculated Urbach energy follow the rule of phonon-assisted transitions. The ionic conduction mechanism is determined by activation energy process. Substitution up to 10 wt% LiCl provides high ionic conductivity (1.9 × 10^?2 Ω^?1 m^?1) due to the high average electronegativity of LiCl which increases the polarizability of lithium ions. The small cation–anion distance approach confirmed the enhancement in ionic conductivity of LiCl containing glass compared to that of Li₂O. Due to the large size of Cl^? ions, there is an expansion of the lattice which in turn broadens the available path windows. For 12.5 wt% LiCl, anomalous density behavior is observed and a reduction in conductivity is occurred, σ = 5.4 × 10^?3 Ω^?1 m^?1. Owing to the model of bond fluctuation, the reduction is attributed to the increase in the alkali halide concentration which creates bottlenecks that hinder the motion of Li⁺ ions. The ionic conductivity character is strongly supported by the behavior of the glass ionicity factor, density, molar volume, refractive index, average boron–boron separation, molar refraction, metallization criterion and non-bridging oxygen concentration of the studied glass.     

Thermal expansion of glass–ceramics in the system BaO/Al2O3/B2O3

Glasses in the system BaO/Al₂O₃/B₂O₃ with and without the addition of platinum were melted. In one sample series, the BaO-concentration was varied while the ratio [Al₂O₃]/[B₂O₃] was kept constant. In another sample series, the [BaO]/[Al₂O₃]-ratio (= 0.9) was kept constant and the B₂O₃ concentration was varied. The samples were thermally treated at 720 °C for 24 h and subsequently at 780 °C for 4 h. In most thermally treated samples, the crystalline phase BaO · Al₂O₃ · B₂O₃ occurred. At some compositions, the platinum-doped samples showed larger concentrations of the crystalline phases. The most remarkable property of the obtained glass–ceramics is their zero or negative thermal expansion coefficient. Here, notable differences were observed: samples with fine grained microstructures showed thermal expansion coefficients approximately zero up to temperatures of around 80 °C. By contrast, samples with coarser microstructures and large spheroidal crystals exhibit negative expansion coefficients up to temperatures of around 280–375 °C. The thermal expansions of these samples were close to those of the mean thermal expansion of the unit cell of the BaO · Al₂O₃ · B₂O₃ phase. The thermal expansion of the fine grained samples was approximately equal to that of the crystallographic a-axis of the BaO · Al₂O₃ · B₂O₃ phase.     

Properties and structure of (1 − x)Li2O–xNa2O–Al2O3–4SiO2 glass systems

(1 − x)Li₂O–xNa₂O–Al₂O₃–4SiO₂ glasses were studied for the progressive percentage substitution of Na₂O for Li₂O at the constant mole of Al₂O₃ and SiO₂. The crystallization temperature at the exothermic peak increased from 898 to 939 °C when the Na₂O content increases from 0 to 0.6 mol. The coefficient of thermal expansion and density of these as-quenched glasses increase from 6.54 × 10⁻⁶ °C⁻¹ to 10.1 × 10⁻⁶ °C⁻¹ and 2.378 g cm⁻³ to 2.533 g cm⁻³ when the Na₂O content increases from 0 to 0.4 mol, respectively. The electrical resistivity has a maximum value at Na₂O · (Li₂O + Na₂O)⁻¹ = 0.4. The activation energy of crystallization decreases from 444 to 284 kJ mol⁻¹ when the Na₂O content increased from 0 to 0.4 mol. Moreover, the activation energy increases from 284 kJ mol⁻¹ to 446 kJ mol⁻¹ when the Na₂O content increased from 0.4 to 0.6 mol. The FT-IR spectra show that the symmetric stretching mode of the SiO₄ tetrahedra (1035–1054 cm⁻¹) and AlO₄ octahedra (713–763 cm⁻¹) exhibiting that the network structure is built by SiO₄ tetrahedra and AlO₄.     

Structural impact of iron ions on BaBiBO4 glasses: Spectroscopic and dielectric investigations

Transparent glasses of composition 10BaO.20Bi₂O₃.(70 ? x)B₂O₃.xFe₂O₃ (wt.%) where 0 ≤ x ≤ 2.0, were characterized by XRD and SEM. Physical, spectroscopic and dielectric properties were investigated. At higher dopant of Fe₂O₃, EPR results revealed that, the number of Fe³⁺ ions participate in the resonance is decreased by forming a new signal at g ≈ 3.015 due to increase of antiferromagnetic interaction of Fe³⁺ ions and/or formation of low spin Fe³⁺ ions in the glass matrix. With initial 0.5 wt.% doping of Fe₂O₃, less dense glass is formed with colloids of metallic Bi⁰ atoms. The absorption bands at 604 and 712 nm in F5 glass are ascribed to Bi⁰ and Bi⁺ radicals respectively. No characteristic Fe³⁺ absorption bands (spin-forbidden) are found. Fe²⁺ ions are increased at higher concentration of Fe₂O₃. Higher concentration of Fe₂O₃ is favorable for BO₂O^?, BO₃, BiO₆ and FeO₆ symmetry unit leads to low band gap and high Urbach energy. By doping of Fe₂O₃ the dielectric parameters like dielectric constant (ε′), loss (tanδ and ac electrical conductivity (σ_ac) are found to increase.     

Glass composition dependence of luminescence due to Ge2+ center in germanate glasses

Germanate glasses were prepared by the melt-quenching method using an assembled hot-thermocoupler equipped in a sample chamber of a fluorescence spectrometer, and subsequently their luminescence and excitation spectra were measured. In the GeO₂ glass, luminescence bands due to the Ge²⁺ center appeared at the central wavelengths of 300 and 395 nm, their excitation bands being at 250 and 330 nm, respectively. In the (100 − x)GeO₂ − xM_mO_n glasses, for M_mO_n = B₂O₃ (x ≦ 50), SiO₂ (x ≦ 40), and Al₂O₃ (x ≦ 2), the luminescence intensity and therefore the amount of the Ge²⁺ center increased with increasing the content of M_mO_n, where M^(2n/m)+ ions (B³⁺, Si⁴⁺, and Al³⁺) have lower basicities than a Ge⁴⁺ ion. Contrarily, for M_mO_n = Li₂O (x ≦ 30), Na₂O (x ≦ 20), K₂O (x ≦ 20), CaO (x ≦ 20), SrO (x ≦ 3), BaO (x ≦ 15), ZnO (x ≦ 20), Ga₂O₃ (x ≦ 10), Sb₂O₃ (x ≦ 20), Bi₂O₃ (15 ≦ x ≦ 25), TiO₂ (x ≦ 3), and Nb₂O₅ (x ≦ 10), the luminescence intensity and the amount of the Ge²⁺ center rapidly decreased with increasing the amount of additives and disappeared, where M^(2n/m)+ ions (Li⁺, Na⁺, K⁺, Ca²⁺, Sr²⁺, Ba²⁺, Zn²⁺, Ga³⁺, Sb³⁺, Bi³⁺, Ti⁴⁺, and Nb⁵⁺) have higher basicities than a Ge⁴⁺ ion.     

EPR and optical studies of Mn2+ ions in Li2O–Na2O–B2O3 glasses – An evidence of mixed alkali effect

EPR and optical absorption spectra of 0.5 mol% MnO₂ doped xLi₂O–(30 − x)Na₂O–69.5B₂O₃ (5 ⩽ x ⩽ 25) glasses have been studied. The EPR spectra exhibit resonance signals characteristic of Mn²⁺ ions. The resonance signal at g ≅ 2.0 is due to Mn²⁺ ions in an environment close to octahedral symmetry, whereas the resonances at g ≅ 4.3 and g ≅ 3.3 are attributed to the rhombic surroundings of the Mn²⁺ ions. The ionic character (A), the number of spins participating in resonance (N), optical band gap energies (E_opt) and Urbach energies (ΔE) show the mixed alkali effect (MAE) with composition. The present study gives an indication that the size of alkalis we choose, is also an important contributing factor in showing the MAE. The variation of N with temperature obeys the Boltzmann law. The optical absorption spectra show a single broad band at ∼21 000 cm⁻¹ corresponding to the transition ⁶A_1g(S) → ⁴T_1g(G) which exhibits a blue shift with x. The theoretical values of optical basicity (Λ_th) have also been evaluated.     

Thermal and optical properties of CuO–BaO–B2O3–P2O5 glasses

CuO-doped barium borophosphate glasses in a series of xCuO–(45 − x)BaO–10B₂O₃–45P₂O₅ in molar ratio with x = 0–15 mol% were prepared by a melt-quenching technique. All the glasses had excellent thermal stability against crystallization. Glass transition temperature, thermal expansion coefficient and molar volume decrease with increasing CuO concentration. The linear relationship between the absorption coefficient and CuO concentration exists for a peak wavelength in the transitions of ²A_1g → ²B_1g, ²B_2g → ²B_1g, ²E_g → ²B_1g. The relationship between the properties and glass structure evaluated by Raman spectroscopy is discussed.     

Ultrafine Co1−xZnxFe2O4 particles synthesized by hydrolysis: Effect of thermal treatment and its relationship with magnetic properties

Co_1−xZn_xFe₂O₄ (x = 0, 0.2 and 0.4) fine powders with particles size of 3 nm were prepared by hydrolysis method. The powders were annealed at 500 °C for 3 h. With heat treatment, the average particles size increased to 12 nm with corresponding increase in blocking temperature, saturation magnetization and reduced remanence. A significant increase in coercive field was found only for the pure CoFe₂O₄.     

Spectral studies of Sm3+ and Dy3+ doped lithium cesium mixed alkali borate glasses

The effect of host glass composition on the optical absorption and fluorescence spectra of Sm³⁺ and Dy³⁺ has been studied in mixed alkali borate glasses of the type 67B₂O₃ · xLi₂O · (32 − x)Cs₂O (x = 8, 12, 16, 20 and 24). The Judd–Ofelt intensity parameters (Ω₂, Ω₄ and Ω₆) are calculated. The radiative transition probabilities (A), radiative lifetimes (τ_R), branching ratios (β) and integrated absorption cross-sections (Σ) are computed for certain excited states of Sm³⁺ and Dy³⁺ ions for different x values in the glass matrix. Stimulated emission cross-sections (σ_p) are obtained for certain emission transitions of two ions in these mixed alkali borate glasses. These parameters are compared for different x values in the glass matrix. Variation of these parameters with x in the glass matrix has been studied.     

Electrooptical Kerr phenomenon and Raman spectroscopy of one lithium–niobium–silicate glass-forming system

Raman spectra and electrooptical Kerr coefficients of glasses belonging to one lithium–niobate–silicate glass-forming system xNb₂O₅ · (66 ? x)SiO₂ · 19Li₂O · 11K₂O · 2B₂O₃ · 2CdO are studied. It has been found that these glasses demonstrate a record value of electrooptical Kerr coefficient; the glass with x = 35 showed electrooptical Kerr coefficient equal to 266 × 10^?16 m/V². Using Raman spectroscopy combined with the concept of Constant Stoichiometric Groupings, a correlation of electrooptical Kerr coefficients of these glasses with the content of Li₂O · Nb₂O₅ (or 2LiNbO₃) groupings has been demonstrated. The hypothesis that electrooptical Kerr sensitivity of glasses is related to the ordered regions with composition and symmetry corresponding to some of known electrooptical crystals has been verified. These regions, which the authors called ‘Crystal Motifs’, are identified with the groupings found in studying Raman spectra of the glasses.     

Structure and properties of Sb2O3-containing zinc borophosphate glasses

ZnO–B₂O₃–P₂O₅ glasses formulated with Sb₂O₃ were investigated in the series 50ZnO–10B₂O₃–40P₂O₅ + xSb₂O₃ (x = 0–70 mol%). With increasing Sb₂O₃ content, the values of glass transition temperature decrease from 492 °C down to 394 °C. The dissolution rate of the glasses reveals a maximum for the glass with x = 15 mol% Sb₂O₃. Raman spectra with increasing Sb₂O₃ content reflect the depolymerisation of phosphate chains. Antimony at low Sb₂O₃ content forms individual SbO₃ pyramids manifested in the Raman spectra by a broad vibrational band at ∼520–690 cm⁻¹. In the glasses with a higher Sb₂O₃ content SbO₃ units link into chains and clusters with Sb–O–Sb bridges manifested in the Raman spectra by a strong broad band at 380–520 cm⁻¹. The ³¹P MAS NMR spectra with increasing Sb₂O₃ content reflect the depolymerisation of phosphate chains at low Sb₂O₃ content and only small changes in the PO₄ coordination at a high Sb₂O₃ content. ¹¹B MAS NMR spectra reveal a steady transformation of B(OP)₄ units into B(OP)_4−x(OSb)_x units, accompanied by the transformation of BO₄ into BO₃ units with increasing Sb₂O₃ content.