Effect of stress ratio and specimen thickness on fatigue crack growth of CK45 steel

Presented are the effect of stress ratio and thickness on the fatigue crack growth rate of CK45 steel according to DIN 17200. Test results are obtained for constant amplitude load in tension with three stress ratios of R=0, 0.2 and 0.4 and three specimen thicknesses of B=6, 12 and 24 mm. Microgauge crack opening values were used to calculate ΔK_eff values from which the da/dN − ΔK_eff curves are obtained. Crack closure can be applied to explain the influence of mean stress and specimen thickness on the fatigue crack growth rate in the second regime of the two-parameter crack growth rate relation. An empirical model is chosen for calculating the normalized load ratio parameter U as a function of R, B and ΔK and, for correlating the test data.     

Influence of mean stress on the fatigue crack growth characreristics of CrlMo steel tube at elevated temperature

The fatigue crack growth characteristics of CrlMo steel have been investigated at 861 K over the R-ratio range 0.1–0.7 utilising a dwell time of 10 min. at maximum load. All tests were conducted under load control in a laboratory air environment. It was established that the R-ratio significantly affected the fatigue crack extension behaviour inasmuch that with increasing R-ratio, the critical ΔK level for the onset of creep fatigue interactive growth, ΔK^IG, decreased from 20 to 7 MPa√m and the threshold stress intensity, ΔK_th, decreased from 9 to about 3 MPa√m. At intermediate ΔK levels, i.e. between ΔK_th and ΔK^IG, the fatigue crack extension rates, for all R-ratio values, resided on or slightly below the CTOD line, which represents the upper bound for contrnuum controlled fatigue crack growth. Creep fatigue interactive growth was typified by crack extension rates that reside above the CTOD line with a ΔK^IG dependence; the attainment of some critical creep condition or crack linkage condition which causes the abrupt change in crack extension behaviour at ΔK^IG; and crack extension occurs almost exclusively in an intergranular manner. The R-ratio and ΔK^IG followed a linear relation. A literature review concerning the effect of temperature on the threshold fatigue crack growth characteristics of low alloy ferritic steels demonstrated powerful effects of temperature; the magnitude of these effects, however, were dependent upon the testing temperature regime and R-ratio level. The effect of R-ratio on ΔK_th was greatest at temperatures >400°C, significant at ambient temperatures and least in the temperature range 90°C to <300°C. The relationship between temperature and ΔK_th, at a given R-ratio, exhibited a through and a minimum ΔK_th value was observed in the temperature range 200–250°C. The magnitude of the temperature effects on ΔK_th decreased with increasing R-ratio. Such effects of temperature and R-ratio on ΔK_th was reasonably explained in terms of crack closure effects. Finally, the present elevated temperature fatigue crack growth data exhibited massive crack extension enhancement values when compared to ambient near-threshold fatigue crack growth data for CrlMo steel. Such large enhancement values were the combined effects of temperature (environment) and frequency.     

The effect of contact stress intensity factors on fatigue crack propagation

Using the technique of Dimensional Analysis the phenomenon of crack closure is modelled using the concept of a contact stress intensity factor Kc. For constant amplitude loading, a simple expression, Kc_max = g(R) ΔK, is obtained without making idealized assumptions concerning crack tip behaviour. Further, by assuming that crack closure arises from the interaction of residual plasticity in the wake of the crack and crack tip compressive stresses, the function g(R) is shown to be constant for non-workhardening materials. This implies that any dependency of Kc_max on R must be attributed to the workhardening characteristic of the material. With Kc known, an “effective” stress intensity factor Ke may be calculated and incorporated into a crack growth law of the form da/dn = f(ΔKe). From analysis, it can be deduced that for a workhardening material, Kc_max will decrease as R increases and the effective stress intensity factor will increase. This means that the fatigue crack propagation rate will increase with R, in accordance with experimental observations.     

Effect of humidity and R-ratio on the near threshold fatigue crack growth of two granular bainitic microstructures

The present report has shown that in ferrite-martensite microstructures, the relative humidity of an air environment can affect both the near threshold fatigue crack growth behaviour and the intermediate Stage II fatigue characteristics. The magnitude of the threshold stress intensity, ΔK_th, was not affected by relative humidity and the significant effect of R-ratio on ΔK_th was suitably demonstrated.The relative humidity affected the nature of both the subcritical static failure mode and the final stage III static failure mode. A direct relationship between the degree of fatigue crack growth enhancement and the extent of transgranular cleavage was evidenced.     

Mixed mode fatigue crack growth and the strain energy density factor

The strain energy density factor S was first proposed by Sih for the prediction of the critical of the load and failure direction under monotonic, mixed mode loading condition. It seems a natural extension to apply the same concept to fatigue crack propagation. However, a close examination of the existing theory indicates that the Strain Energy Density Factor cannot logically account for the phenomena of the R-ratio effect and crack arrest. Thus, modification is necessary before the concept can be applied successfully for the prediction of mixed mode fatigue crack propagation.Based on the concept of hysteresis energy dissipation, an effective strain energy density factor range, ΔS_p,eff, is proposed for the correlation of fatigue crack growth data. ΔS_p,eff is consistent with the concept of crack closure. Experimental investigation indicates that it could predict the crack growth rates and trajectories.     

Near threshold fatigue behaviour of flake graphite cast irons microstructures

This paper describes the influence of material toughness degradation, through reversed temper embrittlement (RTE) and mean stress on the near threshold fatigue crack growth characteristics of a CrMoV turbine bolting steel at ambient and elevated temperatures. It was established at ambient temperatures that strong effects of R-ratio and material condition (toughness) were observed on near threshold fatigue crack growth characteristics. At elevated temperatures it was shown that for the non-embrittled material that only under low R-ratio conditions did increased temperature increase the level of threshold stress intensity ΔK_th, by some 20%. In the case of embrittled material, increasing the temperature increased ΔK_th levels by around 30% and decreased near threshold growth rates by an order of magnitude at low to intermediate R-ratio levels.The effects of R-ratio on ΔK_th for all material and mechanical testing conditions could be simply expressed by the difference between ΔK_th at R = O and a constant B multiplied by R.Quantitative fractographic observations indicated that, generally, the incidence of intergranular failure prevalent in embrittled and non-embrittled steels exhibited a maximum at some specific ΔK level. Also in embrittled steels large effects of environmental assisted crack (EAC) growth were observed at near threshold fatigue crack growth rates. It was suggested that this was the result of the much reduced material cohesive strength which was caused by the presence of both impurity and hydrogen atoms.     

Fatigue crack growth studies in rail steels and associated weld metal

Fatigue crack growth studies in rail steels and associated weld metal have shown that (a) deformed rail steel exhibited fatigue crack growth rates that are slightly faster than undeformed rail steel and (b) weld metal growth data are appreciably faster than rail steel growth results and exhibit growth rate plateaux that reside above the upper bound reported for rail steel fatigue crack growth.In rail steel microstructures at low ΔK levels fatigue crack extension occurred by a ductile striated growth mechanism. However at K_max values approaching 40 MPa √m transgranular cleavage facets initially formed and their incidence increased with K_max until final fast fracture. The average cleavage facet size agreed well with pearlite nodule dimensions of 60–100 μm.The weld metal microstructure was much coarser than the rail steel and contained highly directional columnar grain growth. At all ΔK levels the dominant fracture mode was transgranular cleavage containing small isolated regions of ductile striated fatigue crack growth. The cleavage facet size varied from 150 to 600 μm; such a large variation was explained by the fact that in general crack extension tended to occur in association with the proeutectoid ferrite phase.     

Fatigue crack extension behaviour in porous plasma spray 80%Ni---20%Cr material: The influence of R-ratio

This paper attempts to describe the fatigue crack growth response of a plasma spray 80%---20%Cr material, utilised in the corrosion protection of engineering components, whose microstructure consisted of (i) an austenitic matrix, (ii) a secondary dispersion of a chromite non-metallic inclusion phase and (iii) regions of closed and connected porosity.It was demonstrated that little or no effect of R-ratio was observed on the threshold stress intensity range ΔK_th, which was attributed to both the materials fine to intermediate grain size and probable plain stress testing conditions which significantly decrease crack closure effects. At intermediate fatigue crack growth rates high ratio results were an order of magnitude faster than the low R-ratio data. This was the result of the high R-ratio case seeking out more regions of porosity which then increased the local ΔK on the remaining ligaments leading to accelerated crack growth rates.Porosity was shown to significantly decrease the value of ΔK_th and the extent of porosity observed on fatigue fracture surfaces increased with ΔK level and was well in excess of that of 5% recorded by metallography. Hence the growing fatigue crack preferentially sought out regions of porosity as they represented locations of low fracture energy.     

Effect of grain size on slow fatigue crack propagation and plastic deformation near crack tip

Fatigue crack growth and its threshold are investigated at a stress ratio of 0.5 for the three-point bend specimen made of Austenitic stainless steel. The effect of grain size on the crack tip plastic deformation is investigated. The results show that the threshold value Δk_th increases linearly with the square root of grain size d and the growth rate is slower for materials with larger grain size. The plastic zone size and ratio for different grain sizes are different at the threshold. The maximum stress intensity factor is k_max and σ_ys is the yield strength. At the same time, the characteristics of the plastic deformation development is discontinuous and anti-symmetric as the growth rate is increased from 2·10^—8 to 10⁻⁷ mm/cycle.A dimensionless relation of the form for collating fatigue crack starting growth data is proposed in which Δk_th represents the stress intensity factor range at the threshold. Based on experimental results, this relation attains the value of 0.6 for a fatigue crack to start growth in the Austenitic stainless steel investigated in this work. Metallurgical examinations were also carried out to show a transgranular shear mode of cyclic cleavage and plastic shear.     

Mixed mode fatigue crack growth with a sudden change in loading direction

With a sudden change in the maximum load level, there will be a corresponding change in the crack driving force regardless of whether the load is applied monotonically or cyclically. The effective strain energy density factor range ΔS_p,eff has been used to correlate mixed mode fatigue crack propagation where the crack growth direction is not known as an a priori. Examined in this work is a sudden change of load direction on fatigue crack growth while the load level remains unchanged. Yielding is assumed to be localized near the crack tip such that the crack growth behavior can be described adequately by the elastic stress field. Under the conditions investigated, minimal change on crack growth rates is observed. No firm conclusion could be drawn on deviation of crack path for the case considered.     

Ultrasonic evaluation of fatigue crack growth of high strength steel at ambient temperature and below

By means of an ultrasonic testing device, the crack length in compact tension specimens is monitored. Four ultrasonic probes are used to cover the region of crack extension by transmission waves. The echo of the crack is amplified during fatigue crack propagation. By a knowledge of the initial crack length after precracking and the critical crack length, the alteration of the ultrasonic echo provides the information for determining the intermediate crack length which can be used to calculate the stress intensity range ΔK with respect to the elapsed cycles and the crack growth rate, da/dN.     

Reverse temper embrittlement — environmentally assisted cracking interactions in ferritic low alloy steels

Assessed in this study are the relationships that were recorded between the magnitude of the environmental assisted crack (EAC), growth contribution and the fatigue fractographic details observed in steels under ambient conditions. Four discrete static failure modes were observed on the fatigue surfaces; they are primarily transgranular cleavage and intergranular decohesion with a few instances of fan-shaped growth and macrofacet formation. All static failure modes could be explained by Beacham's model for hydrogen assisted cracking. It was established that the extent of EAC growth was uniquely related to the amount of static failure mode and that the relationship agreed well with the predictions of Congleton's model for EAC growth expressed in terms of the ratio of crack growth rate (da/dN)^* in environments of humid air and saline solution to da/dN in dry air for a given stress intensity factor range ΔK.     

Stress intensity factor range and propagation mode of surface cracks under rolling–sliding contact

Finite element analyses were conducted in order to evaluate the mode I and mode II stress intensity factors for inclined edge cracks under cyclic contact load under rolling and rolling–sliding condition. The SIF range depends on crack orientation, crack length to Hertzian contact zone half-width ratio, friction between the crack faces and friction on the contact surface. The results were combined in two compact functions that determine the ΔK_I and ΔK_II values. The crack propagation mode and direction were investigated using both the maximum stress criterion and the minimum strain energy density criterion. The results are displayed in graph form, which allows a fast evaluation of the crack growth condition.     

Grain boundary oxidation and fatigue crack growth at elevated temperatures

Fatigue crack growth rate at elevated temperatures can be accelerated by grain boundary oxidation. Grain boundary oxidation kinetics and statistical distribution of grain boundary oxide penetration depth were studied.At a constant ΔK-level and at a constant test temperature, fatigue crack growth rate, da/dN, is a function of cyclic frequency, ν. A fatigue crack growth model of intermittent micro-ruptures of grain boundary oxide is constructed. The model is consustent with the experimental observations that, in the low frequency region, da/dN is inversely proportional to ν, and fatigue crack growth is intergranular.     

Fractographic analysis of fatigue cracking in spheroidal graphite cast irons

This paper is concerned with the influence of R-ratio on the fatigue threshold ΔK_th, in two spheroidal graphite cast irons. The microstructures, viz, ferritic and pearlitic, exhibited significant and consistent R-ratio effects on ΔK_th. Intergranular failure facets were observed and they tended to reach a maximum amount when the reversed plastic zone size approached grain size dimensions. Reasonable correlation of experimental data required the increment of crack closure effects in the analytical model. At R-ratio values approaching zero, both microstructures showed ΔK_th, values that were markedly greater than those recorded for steels even when the data was corrected or normalised to a constant yield stress and grain size for a specific microstructure. The presence of graphite nodules may cause an increase in crack closure which in turn promoted high ΔK_th values.     

Analytical and experimental evaluations of the influence of fracture surface roughness,its sliding actions and the associated plasticity on fatigue crack propagation

An investigation of fatigue crack propagation in rectangular AM60B magnesium alloy plates containing an inclined through crack is presented in this paper. The behavior of fatigue crack growth in the alloy is influenced by the fracture surface roughness. Therefore, in the present investigation, a new model is developed for estimating the magnitude of the frictional stress intensity factor, k_f, arising from the mismatch of fracture surface roughness during in-plane shear. Based on the concept of k_f, the rate of fatigue crack propagation, db/dN, is postulated to be a function of the effective stress intensity factor range, Δk_eff. Subsequently, the proposed model is applied to predict crack growth due to fatigue loads. Experiments for verifying the theoretical predictions were also conducted. The results obtained are compared with those predicted using other employed mixed mode fracture criteria and the experimental data.     

A comparative study of crack propagation models for PMMA and PVC

An analysis of examining the validity of a unified approach proposed earlier by the authors for the fatigue crack propagation (FCP) of engineering materials to include PMMA and PVC is described. The proposed formulation has been shown capable of characterizing a diversified range of materials with a master FCP diagram and expressed as da/dN = A(ΔG)^m/(G_c − G_max).An experimental program is undertaken to measure fatigue growth rate with the standard compact tension specimen. The FCP results are for the first instance analysed for each material using the unified formulation. The validity of the formulation for producing a master FCP diagram is verified when the fatigue crack growth rates of the materials are successfully characterized in one master diagram, yielding an excellent coefficient of correlation of 0.993. No such success is attained using a number of conventional FCP laws considered most acceptable to characterize polymeric materials.     

Influence of indenter geometry on half-plane with edge crack subjected to fretting condition

An edge crack is analyzed to study fretting failure. A flat punch with rounded corners and a half-plane are regarded as an indenter and a substrate, respectively. Plane strain condition is considered. Contact shear traction in the case of partial slip is evaluated numerically. It is assumed that an initial crack is extended to the point of minimum strain energy density in the half-plane from the trailing edge of contact. Dislocation density function method is used to evaluate K_I and K_II. The variations of K_I and K_II during crack growth are examined in the case of indentation by a punch with different ratio of the flat region (l) to the punch width (L). Sih's minimum strain energy density theory [1] is also applied to predict the propagation direction of the initial crack. The direction evaluated is similar to that found in the experiment. Stress intensity factor ranges (ΔK_I and ΔK_II) are examined during cyclic shear on the contact. For the design of contacting bodies, a suggestible geometry of punch for alleviating cracking failure is studied.     

Fatigue and fretting fatigue of ion-nitrided 34CrNiMo6 steel

This work is concerned with the surface treatment (ion nitriding) of fretting fatigue and fatigue resistance of 34CrNiMo6. Tests are made on a servo-hydraulic machine under tension for both treated and non-treated specimens. The test parameters involve the applied displacements δ±80–±170 μm; fretting pressure σ_n=1000–1400 MPa; fatigue stress amplitude σ_a=380–680 MPa and stress ratio R=−1. The ion nitriding process improves both fatigue and fretting fatigue lives. Subsurface crack initiation from internal discontinuities was found for ion-nitrided specimens.     

Fatigue crack opening stress based on the strip-yield model

The modified strip-yield model based on the Dugdale model and two-dimensional approximate weight function method were utilized to evaluate the effect of in-plane constraint, transverse stress, on the fatigue crack closure. The plastic zone sizes and the crack opening stresses considering transverse stress were calculated for four specimens: single edge-notched tension (SENT) specimen, single edge-notched bend (SENB) specimen, center-cracked tension (CCT) specimen, double edge-notched tension (DENT) specimen under uniaxial loading. And the crack opening behavior of the center-cracked specimen under biaxial loading was also evaluated. Normalized crack opening stresses σ_op/σ_max for four specimens were successfully described by the normalized plastic zone parameter Δω^′_rev/ω^′ considering transverse stress, where Δω^′_rev and ω^′ are the size of the reversed plastic zone at the moment of first crack tip closure and the size of the forward plastic zone for maximum stress, respectively. The normalized plastic zone parameter with transverse stress also was satisfactorily correlated with the behavior of crack closure for CCT specimen under biaxial loading.