Two‐dimensional prediction of time dependent,turbulent flow around a square cylinder confined in a channel

This paper presents two‐dimensional and unsteady RANS computations of time dependent, periodic, turbulent flow around a square block. Two turbulence models are used: the Launder–Sharma low‐Reynolds number k–ε model and a non‐linear extension sensitive to the anisotropy of turbulence. The Reynolds number based on the free stream velocity and obstacle side is Re=2.2×10⁴. The present numerical results have been obtained using a finite volume code that solves the governing equations in a vertical plane, located at the lateral mid‐point of the channel. The pressure field is obtained with the SIMPLE algorithm. A bounded version of the third‐order QUICK scheme is used for the convective terms. Comparisons of the numerical results with the experimental data indicate that a preliminary steady solution of the governing equations using the linear k–ε does not lead to correct flow field predictions in the wake region downstream of the square cylinder. Consequently, the time derivatives of dependent variables are included in the transport equations and are discretized using the second‐order Crank–Nicolson scheme. The unsteady computations using the linear and non‐linear k–ε models significantly improve the velocity field predictions. However, the linear k–ε shows a number of predictive deficiencies, even in unsteady flow computations, especially in the prediction of the turbulence field. The introduction of a non‐linear k–ε model brings the two‐dimensional unsteady predictions of the time‐averaged velocity and turbulence fields and also the predicted values of the global parameters such as the Strouhal number and the drag coefficient to close agreement with the data. Copyright © 2009 John Wiley & Sons, Ltd.     

Numerical prediction of a turbulent curved wake and comparison with experimental data

Numerical studies of the curved wake of a NACA 0012 airfoil of chord length 0.150 m are presented. The airfoil is placed in air at 10 m/s in the straight section of a duct of 0.457 m × 0.457 m cross‐section followed by a 90° bend with a mean radius‐to‐height ratio of 1.17. The trailing edge is located at one chord length upstream of the bend entry plane. The authors' own measurements are used to define the boundary conditions and for comparison with the predicted results. The numerical models are based on the time‐averaged, three‐dimensional conservation equations of fluid flow, incorporating the k–ε, RNG k–ε, realizable k–ε and the Reynolds stress turbulence models. The results show that the models are capable of predicting the effects of curvature on the wake development. However, quantitative differences between prediction and experiment exist. The results obtained using the Reynolds stress model show better agreement with the experimental data, compared with the k–ε based models, but not consistently for all parameters. There are also better predictions by the RNG k–ε and realizable k–ε models compared with the standard k–ε model. The predicted results using the RNG k–ε are closer to experimental data than the realizable k–ε. Copyright © 2005 John Wiley & Sons, Ltd.     

Numerical simulation of turbulent free surface flow with two‐equation k–ε eddy‐viscosity models

This paper presents a finite difference technique for solving incompressible turbulent free surface fluid flow problems. The closure of the time‐averaged Navier–Stokes equations is achieved by using the two‐equation eddy‐viscosity model: the high‐Reynolds k–ε (standard) model, with a time scale proposed by Durbin; and a low‐Reynolds number form of the standard k–ε model, similar to that proposed by Yang and Shih. In order to achieve an accurate discretization of the non‐linear terms, a second/third‐order upwinding technique is adopted. The computational method is validated by applying it to the flat plate boundary layer problem and to impinging jet flows. The method is then applied to a turbulent planar jet flow beneath and parallel to a free surface. Computations show that the high‐Reynolds k–ε model yields favourable predictions both of the zero‐pressure‐gradient turbulent boundary layer on a flat plate and jet impingement flows. However, the results using the low‐Reynolds number form of the k–ε model are somewhat unsatisfactory. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental validation of two depth‐averaged turbulence models

A finite volume turbulence model for the resolution of the two‐dimensional shallow water equations with turbulent term is presented. After making a finite volume discretization of the depth‐averaged k–ε equations in conservative form, the q–r equations, that give stability to the process, are obtained. Wall and inlet boundary conditions for the turbulent equations and wall conditions for the hydrodynamic equations are discussed. A comparison between the k–ε and q–r models and some experimental results is made. Copyright © 2008 John Wiley & Sons, Ltd.     

Experimental and numerical study of developing turbulent flow and heat transfer in convergent/divergent square ducts

 The work reported in this paper is a systematic experimental and numerical study of friction and heat transfer characteristics of divergent/convergent square ducts with an inclination angle of 1^∘ in the two direction at cross section. The ratio of duct length to average hydraulic diameter is 10. For the comparison purpose, measurement and simulation are also conducted for a square duct with constant cross section area, which equals to the average cross section area of the convergent/divergent duct. In the numerical simulation the flow is modeled as being three-dimensional and fully elliptic by using the body-fitted finite volume method and the kɛ turbulence model. The uniform heat flux boundary condition is specified to simulate the electrical heating used in the experiments. The heat transfer performance of the divergent/convergent ducts is compared with the duct with uniform cross section under three constraints (identical mass flow rate, pumping power and pressure drop). The agreement of the experimental and numerical results is quite good except at the duct inlet. Results show that for the three ducts studied there is a weak secondary flow at the cross section, and the circumference distribution of the local heat transfer coefficient is not uniform, with an appreciable reduction in the four corner regions. In addition, the acceleration/deceleration caused by the cross section variation has a profound effect on the turbulent heat transfer: compared with the duct of constant cross section area, the divergent duct generally shows enhanced heat transfer behavior, while the convergent duct has an appreciable reduction in heat transfer performance. Received on 18 September 2000 / Published online: 29 November 2001     

Cubic eddy‐viscosity turbulence models for strongly swirling confined flows with variable density

An investigation on the predictive performance of cubic eddy‐viscosity turbulence models for strongly swirling confined flows with variable density is presented. Comparisons of the prediction with the experiments show some improvements of cubic models over the linear k–ε model. The linear k–ε model does not contain any mechanism to represent the interaction of swirl and density variation and as a consequence it performs poorly. With appropriate modelling, two‐equation cubic turbulence models can capture the subcritical nature of the flow, represent the azimuthal velocity profiles of combined forced‐free vortex motion, and predict the combined effects of swirl and density variation fairly well. However, the calibration of model coefficients is still a topic of investigation. Further amendments are also needed for the equations of k and ε to take into account the effects of swirl and density gradients correctly. Copyright © 2004 John Wiley & Sons, Ltd.     

A non‐linear k–ε model with realizability for prediction of flows around bluff bodies

The incompressible flow around bluff bodies (a square cylinder and a cube) is investigated numerically using turbulence models. A non‐linear k–ε model, which can take into account the anisotropy of turbulence with less CPU time and computer memory then RSM or LES, is adopted as a turbulence model. In tuning of the model coefficients of the non‐linear terms are adjusted through the examination of previous experimental studies in simple shear flows. For the tuning of the coefficient in the eddy viscosity (=C_μ), the realizability constraints are derived in three types of basic 2D flow patterns, namely, a simple shear flow, flow around a saddle and a focal point. C_μ is then determined as a function of the strain and rotation parameters to satisfy the realizability. The turbulence model is first applied to a 2D flow around a square cylinder and the model performance for unsteady flows is examined focussing on the period and the amplitude of the flow oscillation induced by Karman vortex shedding. The applicability of the model to 3D flows is examined through the computation of the flow around a surface‐mounted cubic obstacle. The numerical results show that the present model performs satisfactorily to reproduce complex turbulent flows around bluff bodies. Copyright © 2003 John Wiley & Sons, Ltd.     

Low Reynolds number k–ε model for near‐wall flow

A wall‐distance free k–ε turbulence model is developed that accounts for the near‐wall and low Reynolds number effects emanating from the physical requirements. The model coefficients/functions depend non‐linearly on both the strain rate and vorticity invariants. Included diffusion terms and modified C_ε(1,2) coefficients amplify the level of dissipation in non‐equilibrium flow regions, thus reducing the kinetic energy and length scale magnitudes to improve prediction of adverse pressure gradient flows, involving flow separation and reattachment. The model is validated against a few flow cases, yielding predictions in good agreement with the direct numerical simulation (DNS) and experimental data. Copyright © 2005 John Wiley & Sons, Ltd.     

SPH computation of plunging waves using a 2‐D sub‐particle scale (SPS) turbulence model

The paper presents a 2‐D large eddy simulation (LES) modelling approach to investigate the properties of the plunging waves. The numerical model is based on the smoothed particle hydrodynamics (SPH) method. SPH is a mesh‐free Lagrangian particle approach which is capable of tracking the free surfaces of large deformation in an easy and accurate way. The Smagorinsky model is used as the turbulence model due to its simplicity and effectiveness. The proposed 2‐D SPH–LES model is applied to a cnoidal wave breaking and plunging over a mild slope. The computations are in good agreement with the documented data. Especially the computed turbulence quantities under the breaking waves agree better with the experiments as compared with the numerical results obtained by using the k–ε model. The sensitivity analyses of the SPH–LES computations indicate that both the turbulence model and the spatial resolution play an important role in the model predictions and the contributions from the sub‐particle scale (SPS) turbulence decrease with the particle size refinement. Copyright © 2006 John Wiley & Sons, Ltd.     

An eddy viscosity model with near‐wall modifications

An extended version of the isotropic k–ε model is proposed that accounts for the distinct effects of low‐Reynolds number (LRN) and wall proximity. It incorporates a near‐wall correction term to amplify the level of dissipation in nonequilibrium flow regions, thus reducing the kinetic energy and length scale magnitudes to improve prediction of adverse pressure gradient flows, involving flow separation and reattachment. The eddy viscosity formulation maintains the positivity of normal Reynolds stresses and the Schwarz' inequality for turbulent shear stresses. The model coefficients/functions preserve the anisotropic characteristics of turbulence. The model is validated against a few flow cases, yielding predictions in good agreement with the direct numerical simulation (DNS) and experimental data. Comparisons indicate that the present model is a significant improvement over the standard eddy viscosity formulation. Copyright © 2005 John Wiley & Sons, Ltd.     

Verification testing in computational fluid dynamics: an example using Reynolds‐averaged Navier–Stokes methods for two‐dimensional flow in the near wake of a circular cylinder

Verification testing was performed for various Reynolds‐averaged Navier–Stokes methods for uniform flow past a circular cylinder at Re= 5232. The standard and renormalized group (RNG) versions of the k–ε method were examined, along with the Boussinesq, Speziale and Launder constitutive relationships. Wind tunnel experiments for flow past a circular cylinder were also performed to obtain a comparative data set. Preliminary studies demonstrate poor convergence for the Speziale relationship. Verification testing with the standard and RNG k–ε models suggests that the simulations exhibit global monotonic convergence for the Boussinesq models. However, the global order of accuracy of the methods was much lower than the expected order of accuracy of 2. For this reason, pointwise convergence ratios and orders of accuracy were computed to show that not all sampling locations had converged (standard k–ε model: 19% failed to converge; RNG k–ε model: 14% failed to converge). When the non‐convergent points were removed from consideration, the average orders of accuracy are closer to the expected value (standard k–ε model: 1.41; RNG k–ε model: 1.27). Poor iterative and global grid convergence was found for the RNG k–ε/Launder model. The standard and RNG k–ε models with the Boussinesq relationship were compared with experimental data and yielded results significantly different from the experiments. Copyright © 2003 John Wiley & Sons, Ltd.     

Evaluation of erosion in a two‐way coupled fluid–particle system

In this study, the effects of flow turbulence intensity, temperature, particle sizes and impinging velocity on erosion by particle impact are demonstrated numerically. Underlying turbulent flow on an Eulerian frame is described by the compressible Reynolds averaged Navier–Stokes equations with a RNG k–ε turbulence model. The particle trajectories and particle–wall interactions are evaluated by a Eulerian–Lagrangian approach in a two‐way coupling system. An erosion model considering material weight removal from surfaces is used to predict erosive wear. Computational validation against measured data is demonstrated satisfactorily. The analysis of erosion shows that the prevention of erosion is enhanced by increasing the effects of flow temperature and turbulence intensity and reducing particle inertial momentum. Copyright © 2001 John Wiley & Sons, Ltd.     

Reynolds‐stress modelling of M = 2.25 shock‐wave/turbulent boundary‐layer interaction

M = 2.25 shock‐wave/turbulent‐boundary‐layer interactions over a compression ramp for several angles (8, 13 and 18°) at Reynolds‐number Re=7 × 10³ were simulated with three low‐Reynolds second‐moment closures and a linear low‐Reynolds standard k–ε model. A detailed assessment of the turbulence closures by comparison with both mean‐flow and turbulent experimental quantities is presented. The Reynolds‐stress model which is wall‐topology free and which uses an optimized redistribution closure, is in good agreement with experimental data both for wall‐pressure and mean‐velocity profiles. Detailed analysis of three components of the Reynolds‐stress tensor (comparison with measurements and transport‐equation budgets) provides a critical evaluation of full Reynolds‐stress models for the separated supersonic compression ramp. The discrepancy observed in the shock‐wave foot region, between computations and measurements for the Reynolds‐stresses profiles, could be explained by considering the experimental shock‐wave oscillation and directions for future modelling work are indicated. Copyright © 2007 John Wiley & Sons, Ltd.     

On steady state computation of turbulent flows using k–ε models approximated by the time splitting method

The time splitting method is frequently used in numerical integration of flow equations with source terms since it allows almost independent programming for the source part. In this paper we will consider the question of convergence to steady state of the time splitting method applied to k–ε turbulence models. This analysis is derived from a properly defined scalar study and is carried out with success for the coupled k–ε equations. It is found that the time splitting method does not allow convergence to steady state for any choice of finite values of the time step. Numerical experiments for some typical turbulent compressible flow problems support the fact that the time splitting method is always nonconvergent, while its nonsplitting counterpart is convergent. Copyright © 2005 John Wiley & Sons, Ltd.     

Suitability of the k–ω turbulence model for scramjet flowfield simulations

The suitability of Wilcox's 2006 k– ω turbulence model for scramjet flowfield simulations is demonstrated by validation against five test cases that have flowfields representative of those to be expected in scramjets. The five test cases include a 2D flat plate, an axisymmetric cylinder, a backward‐facing step, the mixing of a pair of coaxial jets and the interaction between a shock wave and turbulent boundary layer. A generally good agreement between the numerical and experimental results is obtained for all test cases. These tests reveal that despite the turbulence model's sensitivity to freestream turbulence properties, the numerically predicted skin friction agrees with experimental data and theoretical correlations to their degree of uncertainty. The tests also confirm the importance of using a y⁺ value of less than 1 in getting accurate surface heat transfer distributions. In the coaxial jets case, the importance of matching the turbulence intensities at the inflow plane in improving the predictions of the turbulent mixing phenomena is also shown. A review of guidelines with regard to the setting up of grids and specification of freestream turbulence properties for turbulent Reynolds‐averaged Navier–Stokes CFD simulations is also included in this paper. Copyright © 2011 John Wiley & Sons, Ltd.     

On the performance of sudden‐expansion pipe without/with cross‐flow injection: experimental and numerical studies

The paper explores the possibilities that different turbulence closures offer, for in‐depth analysis of a complex flow. The case under investigation is steady, turbulent flow in a pipe with sudden expansion without/with normal‐to‐wall injection through jets. This is a typical geometry where generation of turbulence energy takes place, due to sudden change in boundary conditions. This study is aimed at investigating the capability of a developed computational program by the present authors with three different turbulence models to calculate the mean flow variables. Three two‐equation models are implemented, namely the standard linear k ? ε model, the low Reynolds number k ? ε model and the cubic nonlinear eddy viscosity (NLEV) k ? ε model. The performance of the chosen turbulence models is investigated with regard to the available data in the literature including velocity profiles, turbulent kinetic energy and reattachment position in a pipe expansion. In order to further assess the reliability of the turbulence models, an experimental program was conducted by the present authors also at the fluid mechanics laboratory of Menoufiya University. Preliminary measurements, including the surface pressure along the two walls of the expansion pipe and the pressure drop without and with the presence of different arrangements of wall jets produced by symmetrical or asymmetrical fluid cross‐flow injection, are introduced. The results of the present studies demonstrate the superiority of the cubic NLEV k ? ε model in predicting the flow characteristics over the entire domain. The simple low Reynolds number k ? ε model also gives good prediction, especially when the reattachment point is concerned. The evaluation of the reattachment point and the pressure‐loss coefficient is numerically addressed in the paper using the cubic NLEV k ? ε model. The results show that the injection location can control the performance of the pipe‐expansion system. It is concluded that the introduction of flow injection can increase the energy loss in the pipe expansion. The near‐field turbulence structure is also considered in the present study and it is noticed that the turbulence level is strongly affected by the cross‐flow injection and the jet location. Copyright © 2011 John Wiley & Sons, Ltd.     

A simplified v2–f model for near‐wall turbulence

A simplified version of the v²–f model is proposed that accounts for the distinct effects of low‐Reynolds number and near‐wall turbulence. It incorporates modified C_ε(1,2) coefficients to amplify the level of dissipation in non‐equilibrium flow regions, thus reducing the kinetic energy and length scale magnitudes to improve prediction of adverse pressure gradient flows, involving flow separation and reattachment. Unlike the conventional v²–f, it requires one additional equation (i.e. the elliptic equation for the elliptic relaxation parameter f_µ) to be solved in conjunction with the k–ε model. The scaling is evaluated from k in collaboration with an anisotropic coefficient C_v and f_µ. Consequently, the model needs no boundary condition on and avoids free stream sensitivity. The model is validated against a few flow cases, yielding predictions in good agreement with the direct numerical simulation (DNS) and experimental data. Copyright © 2007 John Wiley & Sons, Ltd.     

Numerical simulation of flow in a circular duct fitted with air‐jet vortex generators

Most of the fundamental studies of the use of air‐jet vortex generators (AJVGs) have concentrated on their potential ability to inhibit boundary layer separation on aerofoils. However, AJVGs may be of use in controlling or enhancing certain features of internal duct flows. For example, they may be of use in controlling the boundary layer at the entrance to engine air intakes, or as a means of increasing mixing and heat transfer. The objective of this paper is to analyse the flow field in the proximity of an air‐jet vortex generator array in a duct by using two local numerical models, i.e. a simple flat plate model and a more geometrically faithful sector model. The sector model mirrors the circular nature of the duct's cross‐section and the centre line conditions on the upper boundary. The flow was assumed fully turbulent and was solved using the finite volume, Navier–Stokes Code CFX 4 (CFDS, AEA Technology, Harwell) on a non‐orthogonal, body‐fitted, grid using the k–ε turbulence model and standard wall functions. Streamwise, vertical and cross‐stream velocity profiles, circulation and peak vorticity decay, peak vorticity paths in cross‐stream and streamwise direction, cross‐stream vorticity profiles and cross‐stream wall shear stress distributions were predicted. Negligible difference in results was observed between the flat plate and the sector model, since the produced vortices were small relative to the duct diameter and close to the surface. The flow field was most enhanced, i.e. maximum thinning of the boundary layer, with a configuration of 30° pitch and 75° skew angle. No significant difference in results could be observed between co‐ and counter‐rotating vortex arrays. Copyright © 2002 John Wiley & Sons, Ltd.     

Numerical simulations of non‐equilibrium turbulent boundary layer flowing over a bump

Large‐eddy simulation (LES) and Reynolds‐averaged Navier–Stokes simulation (RANS) with different turbulence models (including the standard k?ε, the standard k?ω, the shear stress transport k?ω (SST k?ω), and Spalart–Allmaras (S–A) turbulence models) have been employed to compute the turbulent flow of a two‐dimensional turbulent boundary layer over an unswept bump. The predictions of the simulations were compared with available experimental measurements in the literature. The comparisons of the LES and the SST k?ω model including the mean flow and turbulence stresses are in satisfied agreements with the available measurements. Although the flow experiences a strong adverse pressure gradient along the rear surface, the boundary layer is unique in that intermittent detachment occurring near the wall. The numerical results indicate that the boundary layer is not followed by mean‐flow separation or incipient separation as shown from the numerical results. The resolved turbulent shear stress is in a reasonable agreement with the experimental data, though the computational result of LES shows that its peak is overpredicted near the trailing edge of the bump, while the other used turbulence models, except the standard k?ε, underpredicts it. Analysis of the numerical results from LES confirms the experimental data, in which the existence of internal layers over the bump surface upstream of the summit and along the downstream flat plate. It also demonstrates that the quasi‐step increase in skin friction is due to perturbations in pressure gradient. The surface curvature enhances the near‐wall shear production of turbulent stresses, and is responsible for the formation of the internal layers. The aim of the present work is to examine the response and prediction capability of LES with the dynamic eddy viscosity model as a sub‐grid scale to the complex turbulence structure with the presence of streamline curvature generated by a bumpy surface. Aiming to reduce the computational costs with focus on the mean behavior of the non‐equilibrium turbulent boundary layer of flow over the bump surface, the present investigation also explains the best capability of one of the used RANS turbulence models to capture the driving mechanism for the surprisingly rapid return to equilibrium over the trailing flat plate found in the measurements. Copyright © 2010 John Wiley & Sons, Ltd.