架空输电线防振锤阻尼特性实验研究

本文利用梁的振动理论对防振锤的阻尼特性进行研究。通过正弦激励下的共振驻留法,分别对不同型号以及同种型号不同锤头质量的防振锤进行振动实验,应用能量平衡原理得到了防振锤的阻尼特性曲线,分析了不同模态响应在阻尼耗能中的贡献。考虑不同类型阻尼对于减振性能的作用,在Lazan阻尼假设的基础上,利用经验公式推导了阻尼系数计算公式。结果表明,钢绞线变形大小直接影响防振锤的阻尼值大小;阻尼对减小共振频率附近的受迫振动幅值作用明显,验证了防振锤的减振性能;同时锤头质量的变化可以影响阻尼曲线的变化。以上结论可为防振锤的防振设计和应用提供参考。     

Analytical investigation of an SDOF building structure equipped with a friction damper

The purpose of this study is to investigate analytically a single-degree-of-freedom (SDOF) building structure equipped with a friction damper for assessing its vibration control effect. Friction dampers are installed between stories to reduce inter-story displacements of building structures subjected to external loading. They are in general regarded to generate damping forces characterized by Coulomb damping, of which the directions are opposite to the inter-story velocities of building structures. Hence, the building structure model with friction dampers can be represented by a mass-spring-viscous-Coulomb damping system. The building response reduction as a result of damper installation can be provided by observing the damping ratio rather than the friction force contributed by the dampers. Since a large friction damper force is required to attenuate the response of the building due to strong excitation, friction force ratio is directly related to building response reduction, which is the friction force of the damper versus external force. Therefore, damping and friction force ratios are key parameters, playing a main role in selecting an optimal friction damper, which satisfies target response reduction. This study first identifies an SDOF building structure installed with a friction damper for free vibration with initial conditions. A?closed-form expression of normalized displacement is derived in terms of friction force ratio in the time domain. Peak and valley of displacements are also found and then the time when the structure stops is derived with recursive interval number. This study is extended to identify steady-state vibration of the structure by deriving closed-form solution in case of resonance in terms of friction force ratio. Then, the dissipated energy balance is identified for both free and steady-state vibrations. Finally, equivalent viscous damping ratios are derived by using friction force ratio based on dissipated energy balance equation. The derived equations in terms of viscous damping ratio and friction force ratio can provide insight to design a friction damper for reducing structural displacement under external loadings.     

Free vibration analysis of nonlinear resilient impact dampers

In the present study, free vibration of a vibratory system equipped with an impact damper, which incorporates the Hertzian contact theory, is investigated. A nonlinear model of an impact damper is constructed using spring, mass, and viscous damper. To increase accuracy of the solution, deformation of the impact damper during the collision with and the main mass is considered. The governing coupled nonlinear differential equations of a cantilever beam equipped with the impact damper are solved using the parameter expanding perturbation method. Contact durations, which are obtained using the presented method, are compared with previous results. Gap sizes of the impact dampers are classified to two main parts. The effects of selecting the gap sizes regarding to the discussed classification are investigated on the application of the impact dampers. Based on types of collision between colliding masses, the so-called “effectiveness” is defined. Finally, it is shown variation of the damping inclination with the gap size is similar to variation of the effectiveness.     

时滞耦合质量摆动力吸振器减振系统的等峰优化理论与实验

摆式调谐质量阻尼器因其便于安装、维修、更换,且经济实用,广泛应用于结构减振.它通过将摆的自振频率调谐到接近主系统的控制频率,使摆产生与主系统相反的振动,从而抑制或消除主系统的振动.本文通过对主系统无阻尼的被动减振系统和主系统有阻尼的时滞反馈主动减振系统进行多目标优化设计,实现了对主系统幅频响应曲线的等峰控制和共振峰与反共振峰差值的有效控制.首先,建立了时滞耦合质量摆动力吸振器减振系统的力学模型和振动微分方程,通过对主系统无阻尼的被动减振系统进行等峰优化,获得了减振系统的最优频率比和质量摆的最优阻尼比.对于主系统存在阻尼的被动减振系统,在该优化参数下主系统的幅频响应曲线等峰优化失效.其次,对于主系统存在阻尼的时滞反馈优化控制系统,采用CTCR方法得到了反馈增益系数和时滞的稳定区域.在保证系统稳定的前提下,通过调节反馈增益系数和时滞量两个控制参数能够实现对主系统幅频响应曲线的等峰控制.再次,对共振点处主系统振幅放大因子时滞敏感度和反馈增益系数敏感度进行分析,表明共振点幅值对反馈增益系数比对时滞更为敏感.最后,通过实验分别在频域和时域内对理论结果进行了验证.研究表明,通过采用时滞反馈对摆式调...     

Adaptive tuning of elasto-plastic damper

Hysteretic dampers are frequency independent, and thereby potentially effective for several structural vibration modes, provided that the inherent amplitude dependence can be controlled. An adaptive tuning procedure is proposed, aiming at elimination of the amplitude dependence by adjusting the damper parameter(s) with respect to the magnitude of the damper motion. The procedure is demonstrated in terms of the bilinear elasto-plastic damper model, and optimality corresponds to maximum modal damping. A parametric solution for the damping ratio is obtained by a two-component system reduction technique, and maximization leads to an amplitude dependent expression for the optimal yield level. The amplitude is predicted from the most recent extremum of the damper response, and simultaneously used to adjust the yield level. Numerical examples demonstrate that the adaptive tuning procedure succeeds in controlling the amplitude dependence, resulting in equal damping for the first vibration modes.     

阻尼耗能减振框架结构地震作用振动方程求解及地震反应分析Calculation of vibration equation and analysis of seismic response for damping energy dissipation frame structure

研究了设置耗能阻尼器框架的地震作用振动方程求解及该结构的地震反应。框架结构设置耗能阻尼器后,振动方程的阻尼矩阵不再对振型具有正交性,本文对该振动方程给出了状态方程直接积分法,并与传统强制解耦法进行了比较分析,结果表明强制解耦法对结构第一阶振动反应求解偏差较小,而对于高阶振动反应差别较大,并且强制解耦法高估了阻尼器的减震效果。继而采用状态方程直接积分法对设置有粘滞阻尼器的框架结构进行了地震反应分析,探讨了阻尼器位置对框架结构地震反应的影响,结果表明设置有阻尼器的楼层减振效果明显,未设置阻尼器的楼层减振效果差别较大,甚至有可能出现楼层层间侧移增大的现象,由此提出耗能阻尼器应在结构中合理设置。     

Performance evaluation of shape-memory-alloy superelastic behavior to control a stay cable in cable-stayed bridges

This paper focuses on introducing and investigating the performance of a new passive control device for stay cable in cable-stayed bridges made with shape-memory alloys (SMA). The superelasticity and damping capability of SMA is sought in this study to develop a supplementary energy dissipation device for stay cable. A linear model of a sag cable and a one-dimensional constitutive model for the SMA are used. The problem of the optimal design of the device is studied. In the optimization problem, an energy criterion associated with the concept of optimal performance of the hysteretic connection is used. The maximum dissipation energy depends on the cross-sectional area, the length, and the location of the SMA on the cable. The effectiveness of the SMA damper in controlling the cable displacement is assessed. Furthermore, a study is conducted to determine the sensitivity of the cable response to the properties of the SMA device. The comparison between the SMA damper and a more classical passive control energy dissipation device, i.e., the tuned mass damper (TMD), is carried out. The numerical results show the effectiveness of the SMA damper to damp the high free vibration and the harmonic vibration better than an optimal TMD.     

滞回摩擦型调谐惯质阻尼器结构隔震研究

本文研究一种新型非线性阻尼器——滞回摩擦型调谐惯质阻尼器(HFTID)在工程结构抗震控制中的应用。HFTID由调谐惯质阻尼器(TID)和滞回弹簧摩擦元件并联组成。首先通过谐波平衡方法推导了HFTID单自由度系统力与位移的传递率。然后对HFTID进行了最佳调谐参数优化，得到HFTID最优参数的近似表达式，比较了HFTID和TID振动控制系统的减振效果。结果表明，HFTID相比TID可以进一步降低振动控制系统的传递率。最后，以一栋多层隔震结构为例，将HFTID与TID的隔震效果进行了对比，结果表明，HFTID相比TID在降低地震响应峰值和均方根值方面具有更大优势，验证了HFTID在降低地震响应方面的有效性和实用性。HFTID在建筑和桥梁结构抗震、车辆悬挂系统和其他机械隔震问题上具有潜在的应用前景。     

几何非线性摩擦阻尼隔振系统动力学行为研究

非线性隔振系统由于具有较线性系统更优的隔振性能,因此在工程中应用广泛.本文通过配置与被隔振对象的运动方向相垂直的库伦摩擦阻尼器,构建了几何非线性摩擦阻尼模型.由于引入了几何非线性,因此其摩擦力与位移正相关,这与传统与位移无关摩擦力模型有显著不同.首先,建立了具有几何非线性摩擦阻尼的数学模型以及隔振系统的受迫振动方程;然后,使用谐波平衡法求解了动力学方程,并使用数值仿真方法验证了谐波平衡法求解的准确性;最后,研究了几何非线性摩擦阻尼隔振器的绝对位移传递率和相对位移传递率.研究结果表明,在库伦摩擦阻尼选择适当,非线性摩擦阻尼系统可以在保持高频振动衰减效果的前提下,显著降低系统共振峰,其性能优于传统的恒定摩擦阻尼隔振模型.同时,几何非线性摩擦阻尼系统能够避免传统摩擦阻尼系统中的“锁定”现象,从传递率角度来说,不利于共振峰控制;但从激励环境改变引发隔振系统失效的角度来看,几何非线性摩擦阻尼系统可以拓宽系统对激励幅值的适应范围,避免隔振系统失效.本文的研究结果对此类隔振系统的设计和摩擦阻尼参数的选择具有通用的指导意义.      

高速铁路连续梁桥的共振响应与振动控制研究

以液体粘滞阻尼器为振动控制外部装置，主桥采用欧拉伯努利梁，通过中国和谐号动车组CRH380AL、日本新干线Shinkansen700和欧洲高速列车HSLMA8三种不同类型的高速列车对比，模拟分析了高速列车作用下桥梁结构共振响应的影响因素，以及粘滞阻尼器的阻尼系数与安装位置对桥梁结构振动响应的减振效果。研究结果表明，（1）合理有效地布置列车荷载轴距，可使桥梁结构发生基频共振的列车时速在运营时速之外，避免了桥梁结构发生较大振动峰值响应，即桥梁结构的基频共振；（2）随着粘滞阻尼器阻尼系数的增大，桥梁的加速度峰值在列车不同时速下均在减少，对桥梁振动有着不同程度的减振效果；（3）通过合理安置液体粘滞阻尼器，可有效降低高速列车作用下桥梁结构的共振响应；（4）随着粘滞阻尼器与主梁的连接点位置逐渐远离支座，粘滞阻尼器的减振效果逐渐明显；（5）随着粘滞阻尼器与桥台的连接点位置逐渐靠近支座，粘滞阻尼器的减振效果略有提升，但不明显。     

基于分数阶磁流变液阻尼器模型的车辆悬架组合控制

磁流变液阻尼器的分数阶Bingham模型结构形式简单, 而且可以更好地描述系统的滞回特性. 建立了含有分数阶Bingham模型的单自由度1/4车辆悬架系统模型, 利用磁流变液阻尼器对在路面简谐激励下的非线性车辆悬架系统进行振动控制. 研究了含有分数阶Bingham模型的悬架系统在天棚阻尼半主动控制下的主共振响应, 利用平均法得到了系统的近似解析解. 求解了系统定常解的幅频响应方程, 并根据李雅普诺夫稳定性理论得到了悬架系统的稳定性条件. 通过绘制数值解和解析解的幅频响应曲线对比图, 验证了近似解析解的正确性. 利用簧载质量垂直方向的加速度均方根值分析了半主动控制对车辆乘坐舒适性的影响, 发现天棚阻尼半主动控制策略在低频激励区域反而会降低车辆的乘坐舒适性. 因此提出了一种被动控制与半主动控制相结合的组合控制策略, 并分析了半主动控制参数对振动控制效果的影响. 分析结果表明, 该组合控制策略不但能够提高车辆的乘坐舒适性, 而且能有效抑制悬架系统的主共振振动幅值.      

Passive control of vibration of thin-walled gears: advanced modelling of ring dampers

Vibrations on gears are mainly induced by the gear mesh contact. Resonance conditions of the gear may occur during service if the mesh frequency is close to the natural frequencies of the system at the designed speed of the shaft. Since detuning is not always possible in gears, the response level must be reduced by increasing the damping of the system. In this paper, a passive approach based on the application of a ring damper to reduce the vibration level is presented. The ring damper is placed in a groove underneath the outer rim of the gear. The contact is guaranteed by the preload due to the elasticity of the ring damper itself and above all by the centrifugal force that presses the damper against the groove during rotation. The relative motion of the two components at the contact interface dissipates energy by friction, and hence damping is generated. The vibration amplitude is reduced by optimizing the material and geometrical properties of the ring damper. One of the most important parameters in the determination of the amount of damping due to friction phenomena is the static normal load at the contact, which depends on the mass, the shape, and the material of the ring damper. A numerical method is presented, which couples the static and dynamic equilibrium equations of the assembly. The core of the proposed method is the contact element that takes into account local stick–slip–lift off of the contact and determines the contact forces in terms of static and dynamic loads, which are then used to solve the coupled static and dynamic equilibrium. Since the ring damper has a cut that breaks its continuous circular shape in order to be fitted on the groove, the hypothesis of cyclic symmetry for the gear/ring–damper assembly fails. As a consequence, an appropriate reduced-order modeling is presented to allow the forced response calculations. The algorithm is applied to a dummy bevel gear and to a ring damper having a flat punch contact area. The forced response calculations are performed to highlight the nonlinear interaction between the gear and damper by varying the parameters that mainly affect the amount and distribution of the contact forces and therefore the response level.     

Suppression of multiple modal resonances of a cantilever beam by an impact damper

Impact dampers are usually used to suppress single mode resonance. The goal of this paper is to clarify the difference when the impact damper suppresses the resonances of different modes. A cantilever beam equipped with the impact damper is modeled. The elastic contact of the ball and the cantilever beam is described by using the Hertz contact model. The viscous damper between the ball and the cantilever beam is modeled to consume the vibrational energy of the cantilever beam. A piecewise ordinary differential-partial differential equation of the cantilever beam is established, including equations with and without the impact damper. The vibration responses of the cantilever beam with and without the impact damper are numerically calculated. The effects of the impact absorber parameters on the vibration reduction are examined. The results show that multiple resonance peaks of the cantilever beam can be effectively suppressed by the impact damper. Specifically, all resonance amplitudes can be reduced by a larger weight ball. Moreover, the impacting gap is very effective in suppressing the vibration of the cantilever beam. More importantly, there is an optimal impacting gap for each resonance mode of the cantilever beam, but the optimal gap for each mode is different.     

垂直冲击消振系统简谐激励响应及稳定性分析

运用迭代映射及其稳定性分析原理,研究了垂直冲击消振系统的简谐激励响应及其周期响应的稳定性．首先建立了稳定周期响应的参数区域边界方程,分析了稳定周期运动向混沌转变的一般规律．然后以典型的二阶主振系为例,得到了几个对消振效果影响较大的稳态周期响应区域的详细数值结果,讨论了稳态周期响应区域及附近的消振效果．     

Testing and modeling of a CLEMR damper and its application in structural vibration reduction

In this paper, a new kind of combined lead extrusion magnetorheological (CLEMR) damper is proposed. First, tests on CLEMR damper at different currents, excitation amplitudes, and frequencies are carried out. Experimental results show that even when power fails, CLEMR damper can still absorb and dissipate vibration energy of the structure effectively, and its damping force can also be well adjusted in a large range of damping force. Then a mathematical model employing the current, excitation amplitude, and frequency as inputs is proposed and verified by comparing experimental and numerical results. Comparison results show that the proposed model can describe the effects of current, amplitude, and frequency on properties of CLEMR damper. Finally, elastic-plastic dynamic time-history analyses on frame structure with and without CLEMR damper are carried out to evaluate the effectiveness of CLEMR damper in reducing seismic responses of the structures; dynamic responses of the uncontrolled and the controlled structures are then compared. Comparison results show that the displacement responses of each floor of the controlled structure, as well as the number of the cracking point and yielding point of the member, reduce significantly, which implies that the proposed CLEMR damper holds promise in reducing and suppressing the vibration responses of the civil structures.     

质量阻尼器的发展

广泛评述了调谐质量阻尼器(TMD)、多重调谐质量阻尼器(MTMD)、主动质量阻尼器(AMD)、半主动 TMD(SATMD)、主动调谐/主被动调谐/混合质量阻尼器(ATMD/APTMD/HMD)的研究现状.TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD能够有效地减小结构的风振与地震反应.指出强震下结构设置TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD的主要目的是限制结构屈服的进一步发展.因此,基于非线性结构模型的TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD研究具有重要意义.指出了TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD 有待于进一步研究的若干问题.提出了结构主动多重调谐质量阻尼器(AMTMD)和多重主被动调谐质量阻尼器(MAPTMD)的新控制策略.介绍了AMTMD和MAPTMD的研究进展并指出了进一步研究的发展方向.      

单自由度超弹性SMA减振结构随机振动控制理论研究

利用形状记忆合金（Shape Memory Alloy,简称SMA）丝的超弹性,提出了一种具有复位功能的阻尼器。在SMA丝的Graesser本构模型基础上,建立了阻尼器恢复力的滑移双线性模型;假定滞回面积相等,提出了恢复力的滑移刚塑性模型以近似简化滑移双线性模型。采用等价线性化法建立了单自由度超弹性SMA减振结构在高斯白噪声激励下的平稳随机振动分析公式。通过一算例,考虑不同激励谱密度和结构阻尼比：比较了等价线性法和蒙特卡罗（Monte Carlo）模拟法计算的结构振动响应（位移标准差和速度标准差）,证明了SMA减振结构随机振动控制理论的有效性;比较了等价线性减振结构和无控结构的动力特性（刚度和阻尼比）和振动响应,说明了SMA阻尼器能提高结构的刚度和阻尼比,因而可有效抑制结构的振动。     

Steady-state motion of a plate with a discontinuous mass

An “exact” solution employing the normal mode approach is presented for the steady-state motion of a plate of arbitrary shape and with arbitrary boundary conditions that is provided with a discontinuous mass. The plate is viscously damped and the excitation is furnished in the form of distributed and/or concentrated loads that vary sinusoidally. The rigid mass, which may act as a vibration damper, can be applied to any point in the structure. Experimental studies with a mechanical model corroborate the theoretical results. Results of the analysis are applied to cantilever and simply-supported square plates subjected to base excitation and discrete loads. The effects of all system parameters, including damper location and mass ratio, mode shapes, viscous damping, and excitation frequency are determined. It is found that the system under consideration is an efficient device for reducing the vibration of plates, particularly cantilevered ones.     

考虑扭转耦联效应的附属结构最优位置分析

实际建筑物大多为偏心结构,扭转耦联效应使同层楼板上不同位置处附属结构的动力响应也不相同,通常存在一个平面最优位置.本文建立了主附结构体系的扭转耦联模型,利用复模态理论和模式搜索方法研究了影响附属结构最优位置的几个重要因素,包括地震输入方向、场地类别、主体结构偏心、附属结构质量、频率及阻尼比等,通过数值分析得出了一些有益的结论.     

减振阻尼材料设计方法研究

减振阻尼材料可以改变结构的阻尼特性从而降低振动响应和声辐射水平,因而被广泛应用于飞机结构的减振降噪。本文针对减振阻尼材料的设计和应用开展了一系列试验研究,首先通过材料改性得到了不同主基料下材料的配方对阻尼性能的影响;其次配制了三种不同的约束阻尼结构,通过DMA测试对比了三种约束阻尼结构的最佳使用温度和频率范围;最后对约束阻尼结构的减振效果和粘贴布局应用进行了试验,试验结果表明,约束阻尼结构具有良好的减振效果。通过研究掌握了减振阻尼材料在材料改性、约束阻尼结构设计、粘贴布局应用等方面的一些设计方法,可为后续的进一步研究提供技术支持和参考。