The effect of underplatform dampers on the forced response of bladed disks by a coupled static/dynamic harmonic balance method

Friction contacts are often used in turbomachinery design as passive damping systems. In particular, underplatform dampers are mechanical devices used to decrease the vibration amplitudes of bladed disks.Numerical codes are used to optimize during designing the underplatform damper effectiveness in order to limit the resonant stress level of the blades. In such codes, the contact model plays the most relevant role in calculation of the dissipated energy at friction interfaces. One of the most important contact parameters to consider in order to calculate the forced response of blades assembly is the static normal load acting at the contact, since its value strongly affects the area of the hysteresis loop of the tangential force, and therefore the amount of dissipation.A common procedure to estimate the static normal loads acting on underplatform dampers consists in decoupling the static and the dynamic balance of the damper. A preliminary static analysis of the contact is performed in order to get the static contact/gap status to use in the calculation, assuming that it does not change when vibration occurs.In this paper, a novel approach is proposed. The static and the dynamic displacements of the system (bladed disk+underplatform dampers) are coupled together during the forced response calculation. Static loads acting at the contacts follow from static displacements and no preliminary static analysis of the system is necessary.The proposed method is applied to a numerical test case representing a simplified bladed disk with underplatform dampers. Results are compared with those obtained with the classical approach.     

高效耗能摩擦阻尼钢筋混凝土框架结构减震性能分析

研究了高效耗能摩擦阻尼器的减震机理。利用力学原理，分析了地震作用下高效耗能摩擦阻尼器的摩擦阻尼力放大系数变化规律，推导了设置高效耗能摩擦阻尼器结构的等效阻尼比计算公式。在此基础上，对分别设置传统摩擦阻尼器和高效耗能摩擦阻尼器的框架结构进行了地震反应分析，结果表明，高效耗能摩擦阻尼器通过将较小的摩擦阻尼力放大可以显著降低结构地震反应，减震效果良好；利用本文给出的等效阻尼比分析得出结构顶层位移反应幅值，与阻尼等效前相应值误差不超过10%。     

Analysis and design of the force and displacement transmissibility of nonlinear viscous damper based vibration isolation systems

This study is concerned with the analysis and design of the force and displacement transmissibility of nonlinear viscous damper based vibration isolation systems. Analytical algorithms are derived using the Ritz–Galerkin method to evaluate the transmissibility of SDOF displacement vibration isolation and force vibration isolation systems where a nonlinear viscous damper is used as an energy dissipating device. The results reveal that compared to linear dampers, nonlinear viscous dampers can more significantly improve the system vibration isolation performance in a wider frequency range. A procedure is then proposed based on the analysis results to facilitate the design of nonlinear viscous dampers for system vibration isolation purposes. These results have significant implications for the design of vibration isolation systems in many engineering applications.     

Inner mass impact damper for attenuating structure vibration

The behaviors of a vibration system suppressed with an impact damper are investigated, where the impact damper is simplified as a combination of spring and viscous damping. The analytical theory for the optimal impact control algorithms for impact damper is developed, and the accurate expressions are derived for the optimal values of the impact damper damping and initial displacement in a single-degree-of-freedom structure. The relation between coefficient of restitution and impact damping ratio is obtained. The investigation shows that the effective reduction of the vibration response is nearly independent of the number of impacts, but primarily related to the type of collision which the impact mass collides with the main mass face-to-face. This theory is generalized to continuous structures. An example of an impact damper in a rotating cantilever beam demonstrates that the impact dampers are suitable for attenuating the impulse response of structures unconditional stable without the requirement of the accuracy of the modal information.     

几何非线性摩擦阻尼隔振系统动力学行为研究

非线性隔振系统由于具有较线性系统更优的隔振性能,因此在工程中应用广泛.本文通过配置与被隔振对象的运动方向相垂直的库伦摩擦阻尼器,构建了几何非线性摩擦阻尼模型.由于引入了几何非线性,因此其摩擦力与位移正相关,这与传统与位移无关摩擦力模型有显著不同.首先,建立了具有几何非线性摩擦阻尼的数学模型以及隔振系统的受迫振动方程;然后,使用谐波平衡法求解了动力学方程,并使用数值仿真方法验证了谐波平衡法求解的准确性;最后,研究了几何非线性摩擦阻尼隔振器的绝对位移传递率和相对位移传递率.研究结果表明,在库伦摩擦阻尼选择适当,非线性摩擦阻尼系统可以在保持高频振动衰减效果的前提下,显著降低系统共振峰,其性能优于传统的恒定摩擦阻尼隔振模型.同时,几何非线性摩擦阻尼系统能够避免传统摩擦阻尼系统中的“锁定”现象,从传递率角度来说,不利于共振峰控制;但从激励环境改变引发隔振系统失效的角度来看,几何非线性摩擦阻尼系统可以拓宽系统对激励幅值的适应范围,避免隔振系统失效.本文的研究结果对此类隔振系统的设计和摩擦阻尼参数的选择具有通用的指导意义.      

阻尼耗能减振框架结构地震作用振动方程求解及地震反应分析Calculation of vibration equation and analysis of seismic response for damping energy dissipation frame structure

研究了设置耗能阻尼器框架的地震作用振动方程求解及该结构的地震反应。框架结构设置耗能阻尼器后,振动方程的阻尼矩阵不再对振型具有正交性,本文对该振动方程给出了状态方程直接积分法,并与传统强制解耦法进行了比较分析,结果表明强制解耦法对结构第一阶振动反应求解偏差较小,而对于高阶振动反应差别较大,并且强制解耦法高估了阻尼器的减震效果。继而采用状态方程直接积分法对设置有粘滞阻尼器的框架结构进行了地震反应分析,探讨了阻尼器位置对框架结构地震反应的影响,结果表明设置有阻尼器的楼层减振效果明显,未设置阻尼器的楼层减振效果差别较大,甚至有可能出现楼层层间侧移增大的现象,由此提出耗能阻尼器应在结构中合理设置。     

设置连接阻尼器的相邻结构随机地震动响应的简明封闭解

针对两相邻结构间设置连接阻尼器对结构的减震影响问题,研究了基于Kanai-Tajimi谱地震动激励下的Kelvin型粘弹性阻尼器与相邻结构形成的组合体系的随机地震动系列响应(绝对位移及层间位移)的简明封闭解。首先,利用Kelvin型粘弹性阻尼器本构关系及Kanai-Tajimi谱的滤波方程,将组合体系基于复杂地震动激励精确转化为基于简明白噪声激励的运动方程;其次,利用复模态法获得了组合结构相对于地面的绝对位移、层间位移等系列响应方差及0阶~2阶谱矩的统一简明封闭解。最后,通过算例及与虚拟激励法进行对比,证明本文方法的正确性和简明性;通过与未设置阻尼装置结构体系的动力响应对比,说明了阻尼装置对相邻结构具有良好的减震效果,但局部楼层的层间位移及层间剪力会有所增加。     

Explicit computational method of dynamic response for non-viscously damped structure systems

Non-viscous damping models in which the damping forces depend on the past history of velocities via convolution integrals over some kernel functions have been raised in many engineering fields. This paper describes an explicit computational method of dynamic response for the non-viscously damped structure systems. The explicit formula is derived using the differential property of convolution and the central difference formula of acceleration. The explicit computational procedure of dynamic response is given in detail. Finally, the dynamic responses of MDOF structure system with double exponential model dampers and SDOF structure system with Gaussian model damper are computed using the proposed explicit method. The accuracy and efficiency are discussed by comparison with other two developed methods.     

On the hysteresis of wire cables in Stockbridge dampers

Stockbridge dampers are used e.g. for reducing wind-excited oscillations due to vortex shedding in conductors of overhead lines. In these dampers, mechanical energy is dissipated in wire cables (“damper cables”). The damping mechanism is due to statical hysteresis resulting from Coulomb (dry) friction between the individual wires of the cable undergoing bending deformation. Systems with statical hysteresis can be modelled by means of Jenkin elements arranged in parallel, consisting of linear springs and Coulomb friction elements. The damper cable is a continuous system and damping takes place throughout the whole length of the cable, so that distributed Jenkin elements are used. The local mechanical properties of the wire cable are identified experimentally in the time domain. In particular, the moment–curvature relation is determined experimentally at every location of the wire cable subjected to dynamic flexural deformations. Using such a model for the damper cables, the equations of motion can be formulated for a Stockbridge damper, and discretization of the damper cable leads to a system of non-linear ordinary differential equations. In order to test this dynamical model of a Stockbridge damper we compute impedance curves and compare them to experimental results.     

架空输电线防振锤阻尼特性实验研究

本文利用梁的振动理论对防振锤的阻尼特性进行研究。通过正弦激励下的共振驻留法,分别对不同型号以及同种型号不同锤头质量的防振锤进行振动实验,应用能量平衡原理得到了防振锤的阻尼特性曲线,分析了不同模态响应在阻尼耗能中的贡献。考虑不同类型阻尼对于减振性能的作用,在Lazan阻尼假设的基础上,利用经验公式推导了阻尼系数计算公式。结果表明,钢绞线变形大小直接影响防振锤的阻尼值大小;阻尼对减小共振频率附近的受迫振动幅值作用明显,验证了防振锤的减振性能;同时锤头质量的变化可以影响阻尼曲线的变化。以上结论可为防振锤的防振设计和应用提供参考。     

Qualitative analysis of forced response of blisks with friction ring dampers

A damping strategy for blisks (integrally bladed disks) of turbomachinery involving a friction ring is investigated. These rings, located in grooves underside the wheel of the blisks, are held in contact by centrifugal loads and the energy is dissipated when relative motions between the ring and the disk occur. A representative lumped parameter model of the system is introduced and the steady-state nonlinear response is derived using a multi-harmonic balance method combined with an AFT procedure where the friction force is calculated in the time domain. Numerical simulations are presented for several damper characteristics and several excitation configurations. From these results, the performance of this damping strategy is discussed and some design guidelines are given.     

Adaptive tuning of elasto-plastic damper

Hysteretic dampers are frequency independent, and thereby potentially effective for several structural vibration modes, provided that the inherent amplitude dependence can be controlled. An adaptive tuning procedure is proposed, aiming at elimination of the amplitude dependence by adjusting the damper parameter(s) with respect to the magnitude of the damper motion. The procedure is demonstrated in terms of the bilinear elasto-plastic damper model, and optimality corresponds to maximum modal damping. A parametric solution for the damping ratio is obtained by a two-component system reduction technique, and maximization leads to an amplitude dependent expression for the optimal yield level. The amplitude is predicted from the most recent extremum of the damper response, and simultaneously used to adjust the yield level. Numerical examples demonstrate that the adaptive tuning procedure succeeds in controlling the amplitude dependence, resulting in equal damping for the first vibration modes.     

滞回摩擦型调谐惯质阻尼器结构隔震研究

本文研究一种新型非线性阻尼器——滞回摩擦型调谐惯质阻尼器(HFTID)在工程结构抗震控制中的应用。HFTID由调谐惯质阻尼器(TID)和滞回弹簧摩擦元件并联组成。首先通过谐波平衡方法推导了HFTID单自由度系统力与位移的传递率。然后对HFTID进行了最佳调谐参数优化，得到HFTID最优参数的近似表达式，比较了HFTID和TID振动控制系统的减振效果。结果表明，HFTID相比TID可以进一步降低振动控制系统的传递率。最后，以一栋多层隔震结构为例，将HFTID与TID的隔震效果进行了对比，结果表明，HFTID相比TID在降低地震响应峰值和均方根值方面具有更大优势，验证了HFTID在降低地震响应方面的有效性和实用性。HFTID在建筑和桥梁结构抗震、车辆悬挂系统和其他机械隔震问题上具有潜在的应用前景。     

高速铁路连续箱型梁桥的动力响应与减振分析

根据列车具体的轴距和轴重,建立了和谐号动车组CRH380AL型列车简化模型;对高速铁路两跨连续梁桥采用多自由度欧拉伯努利梁单元进行主梁的模拟,并将液体黏滞阻尼器模拟为有限元阻尼单元;采用Newmark直接积分方法求解了高速列车作用下的连续梁桥运动方程,数值分析了列车车速以及液体黏滞阻尼器的阻尼系数对于高速铁路连续梁桥振动响应的影响。结果表明:黏滞阻尼器对于桥梁具有明显的减振效果,阻尼力不仅与阻尼系数有关还与列车时速有关;同一黏滞阻尼器条件下,桥梁的最大加速度并不随列车速度的增加而单调增加,而是在某些特定列车车速下桥梁的最大加速度出现了峰值,且随着黏滞阻尼器的阻尼系数增大,桥梁振动响应峰值处的最大加速度减幅不同;同一列车时速的条件下,桥梁的减振效果并不是随着阻尼系数的递增呈正比递增,而是随着阻尼系数的增大,阻尼器的减振效果增幅在减小。     

Localization in Nonlinear Mistuned Systems with Cyclic Symmetry

In forced systems with cyclic symmetry localization can occur due toparameter uncertainties. Often, Monte-Carlo simulations are used to findregions, where the system response is sensitive to parameteruncertainties. These simulations require a large computation time.Therefore, an approximate method to calculate the envelopes of thefrequency response functions is developed in this paper. An example of anonlinear system with cyclic symmetry is a bladed disk assembly withfriction dampers. Friction dampers can be installed underneath the bladeplatforms of turbine blades. Due to dry friction and the relative motionbetween blades and dampers, energy is dissipated, which results in areduction of blade vibration amplitudes. By optimizing the mass of thefriction dampers, the best damping effects are obtained, which lead toan increase in the reliability of the turbine. In this paper, thecalculated response of a mistuned bladed disk assembly with frictiondampers is discussed. An approximate method is developed to calculatethe envelopes of the corresponding frequency response function forstatistically varying eigenfrequencies of the blades. Regions wherelocalization can occur with a high probability, are calculated by thismethod.     

电流变液与压电陶瓷复合的自耦合阻尼器

基于智能结构的思想,率先提出设计制作电流变液和压电陶瓷复合的自耦合阻尼器．相比于通常的电流变液阻尼器,该自耦合阻尼器采用压电陶瓷响应外界振动而输出高电压,激励电流变液体工作,从而省去了外加高压电源．随外作用力变化,激励电流变液的压电陶瓷电压自动改变,阻尼器具有自适应的特征,省去了通常的计算机等控制系统．研制的第1代电流变液／压电陶瓷阻尼器实现了自适应的控制过程,显示了良好的减振性能．在第2代产品中采用了新的设计,提高了阻尼器的结构稳定性和可靠性,使阻尼器整体性能得到提高．     

单自由度超弹性SMA减振结构随机振动控制理论研究

利用形状记忆合金（Shape Memory Alloy,简称SMA）丝的超弹性,提出了一种具有复位功能的阻尼器。在SMA丝的Graesser本构模型基础上,建立了阻尼器恢复力的滑移双线性模型;假定滞回面积相等,提出了恢复力的滑移刚塑性模型以近似简化滑移双线性模型。采用等价线性化法建立了单自由度超弹性SMA减振结构在高斯白噪声激励下的平稳随机振动分析公式。通过一算例,考虑不同激励谱密度和结构阻尼比：比较了等价线性法和蒙特卡罗（Monte Carlo）模拟法计算的结构振动响应（位移标准差和速度标准差）,证明了SMA减振结构随机振动控制理论的有效性;比较了等价线性减振结构和无控结构的动力特性（刚度和阻尼比）和振动响应,说明了SMA阻尼器能提高结构的刚度和阻尼比,因而可有效抑制结构的振动。     

高速铁路连续梁桥的共振响应与振动控制研究

以液体粘滞阻尼器为振动控制外部装置，主桥采用欧拉伯努利梁，通过中国和谐号动车组CRH380AL、日本新干线Shinkansen700和欧洲高速列车HSLMA8三种不同类型的高速列车对比，模拟分析了高速列车作用下桥梁结构共振响应的影响因素，以及粘滞阻尼器的阻尼系数与安装位置对桥梁结构振动响应的减振效果。研究结果表明，（1）合理有效地布置列车荷载轴距，可使桥梁结构发生基频共振的列车时速在运营时速之外，避免了桥梁结构发生较大振动峰值响应，即桥梁结构的基频共振；（2）随着粘滞阻尼器阻尼系数的增大，桥梁的加速度峰值在列车不同时速下均在减少，对桥梁振动有着不同程度的减振效果；（3）通过合理安置液体粘滞阻尼器，可有效降低高速列车作用下桥梁结构的共振响应；（4）随着粘滞阻尼器与主梁的连接点位置逐渐远离支座，粘滞阻尼器的减振效果逐渐明显；（5）随着粘滞阻尼器与桥台的连接点位置逐渐靠近支座，粘滞阻尼器的减振效果略有提升，但不明显。     

复合干摩擦的准零刚度隔振系统的亚谐共振

利用增量平均法研究了复合干摩擦阻尼器的准零刚度非线性隔振系统在外部简谐激励作用下的1/3次亚谐共振. 首先利用平均法得到了复合干摩擦的准零刚度隔振系统的主共振近似解析解, 然后在系统主共振近似解析解的基础上将系统的亚谐共振响应看作增量, 并利用平均法得到了准零刚度隔振系统的亚谐共振近似解析解. 利用李雅普诺夫方法得到了准零刚度隔振系统主共振和亚谐共振稳态解的稳定性条件, 并推导了系统1/3次亚谐共振的存在条件. 根据近似解析解分别得到了复合干摩擦的准零刚度隔振系统的主共振和亚谐共振力传递率. 利用数值解验证了准零刚度隔振系统主共振和亚谐共振近似解析解的准确性. 利用系统的近似解析解详细分析了准零刚度参数和干摩擦力对系统主共振和亚谐共振的幅频响应以及力传递特性的影响. 分析结果表明, 通过选取合适的干摩擦力参数, 可以消除准零刚度隔振系统在主共振区域的亚谐共振. 通过复合干摩擦阻尼器不但可以提高准零刚度隔振系统在低频区域的振幅抑制效果, 而且可以降低准零刚度隔振系统的起始隔振频率, 但是会增大系统在有效隔振频带内的力传递率.      

粘滞和粘弹性阻尼器减震结构的等效阻尼

利用积分型本构关系,建立了带支撑的一般粘滞和粘弹性阻尼器单自由度耗能结构的微分-积分混合地震响应方程;基于与随机平均分析完全相同的等效准则,推导了可直接应用反应谱的阻尼器的等效刚度和等效阻尼的解析公式;得到了带支撑广义Maxwell阻尼器和广义微分模型阻尼器的等效刚度和等效阻尼的一般结果。通过与一些典型问题的数值计算结果比较,表明了所提方法的有效性。