基于非线性级联系统的弹性关节空间机器人新型滑模控制

研究了双臂弹性关节空间机器人的改进型非线性干扰观测器(nonlinear disturbance observer,NDO)设计、新型自适应动态终端滑模控制和弹性振动抑制问题。首先,考虑空间机器人的关节弹性,基于非线性级联系统的结构建立弹性关节空间机器人模型,分为外环机械臂动力学和内环关节动力学,具有渐近稳定性。针对外环机械臂动力学模型,设计基于改进型NDO的新型自适应动态终端滑模控制算法。针对内环关节动力学模型,设计力矩反馈控制算法来抑制弹性关节振动。本文提出的基于非线性级联系统的自适应动态终端滑模控制算法具有良好的动态特性及较强的鲁棒性,可在关节柔性刚度较小情况下,快速完成弹性关节振动抑制,实现空间机器人轨迹的精确跟踪。系统仿真试验证明了本文控制算法的正确性。     

全弹性平面运动机器人的高精度运动控制和振动抑制算法研究

为实现对基座、关节和臂均存在弹性的空间机器人运动高精度控制及多重振动抑制,建立了基座、关节和臂全弹性空间机器人动力学模型,并采用运动有限维PD重复学习控制及振动同步抑制方案进行研究.首先,利用线性弹簧、扭转弹簧和欧拉-伯努力梁理论,假设模态法和动量守恒定律,采用拉格朗日方程建立了弹性基座、柔性关节和柔性臂空间机器人动力学模型,之后,选取反映柔性臂振动的前两阶模态及基座和关节刚性运动变量为慢变子变量,选取基座和关节弹性振动变量为快变子变量,根据奇异摄动理论将系统降维分解成慢、快变子系统.最后设计了慢变子系统的运动有限维PD重复学习控制及快变子系统的线性最优双重减振控制构成的总控制器.数值仿真结果验证了算法的有效性.     

柔性关节-柔性臂空间机器人的神经网络自适应反演控制及双重柔性振动抑制

空间机器人系统的柔性主要体现在空间机器人的臂杆和连接各臂杆之间的铰关节。由于空间机器人系统结构的复杂性,以往研究人员对同时具有柔性关节和柔性臂的系统关注不够。为此探讨了参数未知柔性关节-柔性臂空间机器人系统的动力学模拟、轨迹跟踪控制算法设计和关节、臂杆双重柔性振动的主动抑制问题。首先,采用多体动力学建模方法并结合漂浮基空间机器人固有的线动量和角动量守恒动力学特性,推导了系统的动力学方程。以此为基础,考虑到空间机器人实际应用中各关节铰具有较强柔性的情况,引入一种关节柔性补偿控制器解决了传统奇异摄动法应用受关节柔性限制问题,导出了适用于控制系统算法设计的数学模型。然后,利用该模型,基于反演思想在慢时标子系统中设计神经网络自适应控制算法来补偿系统参数未知和柔性关节引起的转动误差,实现系统运动轨迹跟踪性能;针对快时标子系统,设计了鲁棒最优控制算法抑制因柔性关节及柔性臂引起的系统双重弹性振动,保证系统的稳定性。最后,通过仿真对比实验验证了所设计控制算法的有效性。     

柔性铰柔性杆机器人动力学建模、仿真和控制

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.      

DYNAMICS MODELING,SIMULATION, AND CONTROL OF ROBOTS WITH FLEXIBLE JOINTS AND FLEXIBLE LINKS$^{\bf 1)}$

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.     

链状柔性多体机器人系统动力学研究

本文基于Ｊｏｕｒｄａｉｎ变分原理建立了具有链状拓扑结构柔性多体机器人系统动力学通用模型，用在一致质量有限单元法及正则模态分析基础上引入的模态坐标描述构件的弹性形，用独立坐标描述相邻板件间的大位移运动，每个铰容许１－６个自由度，组强非线性惯性耦合的封闭形式的系统动力学微分方程组，文末对单弹性臂和双弹性臂机器人操作手进行动力学仿真。     

机器人粘弹性手臂的动力学有限元分析

本文用动力学虚功原理建立了一般粘弹性大阻尼结构机器人手臂的动力学有限元模型,该模型是时变的Voterra型微分积分方程。文中还提出了以结构动力学中响应计算的逐步积分法为基础的递推求解方法,从而解决了机器人粘弹性手臂动力学建模和分析的理论难题。     

基于干扰观测器的柔性关节空间机器人退步自适应控制

研究了载体位置、姿态均不受控的情况下,系统参数不确定的柔性关节空间机器人轨迹跟踪的控制问题.结合系统动量、动量矩守恒关系,利用拉格朗日法推导出系统的动力学模型.为减小系统柔性关节对系统控制精度的影响,采用关节柔性补偿器来等效降低系统关节的柔性.再借助奇异摄动法,针对系统参数不确定的情况,设计了柔性关节空间机器人基于干扰观测器的退步自适应滑模控制方案.该方案不需要对系统惯性参数进行线性化处理,控制器结构简单,且实现了空间机器人期望轨迹的精确跟踪控制.通过平面两杆空间机器人的数值仿真证明了该方法的有效性.     

考虑摩擦特性的柔性关节空间机器人自适应CMAC神经网络鲁棒控制

讨论了关节摩擦力矩影响下,具有柔性铰关节的漂浮基空间机器人系统的动力学控制问题.设计了基于高斯基函数的小脑神经网络(CMAC)鲁棒控制器和摩擦力矩补偿器.用奇异摄动理论对系统的动力学模型进行快慢变子系统分解,针对快变子系统,设计力矩微分反馈控制器来抑制机械臂关节柔性引起的振动;对于慢变子系统,设计了基于自适应CMAC神...     

基于虚拟力概念的柔性臂空间机器人模糊退步自适应控制算法设计

讨论了漂浮基柔性臂空间机器人系统的动力学模拟、运动轨迹跟踪控制算法设计及柔性振动主动抑制。采用多体动力学建模方法并结合假设模态法,建立了漂浮基柔性臂空间机器人的系统动力学模型。基于该模型,针对系统惯性参数未知情况,提出了刚性运动基于模糊基函数网络自适应调节的退步控制算法,以完成柔性臂空间机器人载体姿态及机械臂各关节铰的协调运动。然后,为了主动抑制系统柔性振动,运用虚拟力的概念,构造了同时反映柔性模态和刚性运动轨迹的混合期望轨迹,通过改造原有的控制算法,提出了基于虚拟力概念的模糊退步自适应控制算法;这样不但保证了之前刚性运动控制方案对模型不确定的鲁棒性,而且能主动抑制柔性振动,从而提高了轨迹跟踪性能。理论分析及数值仿真算例均表明了控制方法的可行性。     

Effect of the deformation in the inertia forces on the inverse dynamics of planar flexible mechanical systems

The inverse dynamics problem for articulated structural systems such as robotic manipulators is the problem of the determination of the joint actuator forces and motor torques such that the system components follow specified motion trajectories. In many of the previous investigations, the open loop control law was established using an inverse dynamics procedure in which the centrifugal and Coriolis inertia forces are linearized such that these forces in the flexible model are the same as those in the rigid body model. In some other investigations, the effect of the nonlinear centrifugal and Coriolis forces is neglected in the analysis and control system design of articulated structural systems. It is the objective of this investigation to study the effect of the linearization of the centrifugal and Coriolis forces on the nonlinear dynamics of constrained flexible mechanical systems. The virtual work of the inertia forces is used to define the complete nonlinear centrifugal and Coriolis force model. This nonlinear model that depends on the rate of the finite rotation and the elastic deformation of the deformable bodies is used to obtain the solution of the inverse dynamics problem, thus defining the joint torques that produce the desired motion trajectories. The effect of the linearization of the mass matrix as well as the centrifugal and Coriolis forces on the obtained feedforward control law is examined numerically. The results presented in this investigation are obtained using a slider crank mechanism with a flexible connecting rod.     

A nonlinear high gain observer based input–output control of flexible link manipulator

The input–output control strategy needs all of the states feedback. However, in flexible link robot manipulators, measuring the time rate of elastic degrees of freedom is practically impossible. In this paper, a new nonlinear high gain observer has been developed to estimate the elastic degrees of freedom and their time derivatives. The control strategy is based on an output redefinition approach which stabilizes the zero dynamics of the manipulator. Finally, the results are presented by implementing the proposed observer and controller on a single link flexible manipulator. Numerical simulations will support the validity of our research results.     

Control and Parameter Optimization of Flexible Robots*

A hierarchical control concept for flexible robot manipulators is presented. The equations of motion are derived using the multibody system method, incorporating flexible links equipped with surface bonded actuating and sensing devices. Exploiting the structure of the dynamic model, the control concept allows combination of any joint level control for the gross motion of the manipulator with decentralized linear control of the elastic deformation of each flexible link. Therefore, the approach is capable of solving both the problem of fast and precise point-to-point motion, with acceptable vibration characteristics, and the problem of accurate trajectory tracking of the end-effector. Control parameters are found through parameter optimization. In order to verify the proposed control strategy, a SCARA robot with one flexible link is considered.     

Order-N Formulation and Dynamics of Multi-Unit Flexible Space Manipulators

As robotic manipulators gain more importance in space operations, it is becoming imperative to understand their distinctive dynamics and control characteristics. With the increasing complexity of space robots, efficient algorithms are now required for their simulation. The present study uses an order-N algorithm, based on the Lagrangian approach and velocity transformations, to simulate the planar dynamics of a novel orbiting manipulator with arbitrary number of slewing and deployable flexible links. The relatively general formulation accounts for interactions between orbital, librational, slewing, deployment, and vibrational degrees of freedom, and thus is applicable to a large class of manipulator systems of contemporary interest. A parametric analysis of the system dynamics is carried out to investigate the effects of initial disturbances, variation of system parameters and maneuver profiles. The study suggests significant coupling between the rigid body motion and structural vibrations. As a result, the system's flexibility can significantly affect the manipulator's performance.     

Dynamics of flexible multibody systems with tree topologies

The dynamic equations of flexible multibody systems with tree topological configuration are derived by using the Jourdain's principle. The independent joint coordinates are introduced to describe the large displacements of the bodies, and the modal coordinates are used to describe small deformations of flexible bodies based on the consistent mass finite element method and normal vibration mode analysis. The minimum differential equations are developed, which are compatible with the equations of multi-rigid body systems or structural dynamics. The stiff problem in the numerical integration is thus alleviated effectively. The method used in this paper can be extended to deal with systems with other topological configurations. Finally, the validity and feasibility of the presented mathematical model are demonstrated by a numerical example of a manipulator with two elastic links. The project supported by National Natural Science Foundation of China     

Complex Motion of Elastic Systems

This paper addresses issues of the theoretical dynamic analysis of elastic links making large relative translational and rotational motions. Mathematical models and analysis techniques for elastic vibrations of such systems are described. Examples of applied problems are adduced     

Influence of elastic compliance of links on the dynamics and accuracy of a manipulating robot with rotational and translational joints

We pose problems of dynamic and kinematic control of spatial motions for multilink manipulating robot with elastic links and with rotational and translational joints. These problems are reduced to solving a system of ordinary and partial differential equations of hybrid type in the independent variables. We use a numerical integration algorithm for such systems which was developed earlier for manipulating robots with elastic links of anthropomorphic type. We discuss the difficulties arising in mathematical simulation of manipulating robots with simultaneously rotational and translational joints and with elastic links. To perform a comparative analysis and estimate the positional accuracy for the center of mass of the weight transported by the manipulator, we pose problems of dynamic and kinematic control of spatial motions of a manipulating robots with rigid links and with rotational and translational joints. The resolving equations obtained in this case are based on the Lagrange formalism of the second kind. By way of example, we present the solution of dynamic control problems for elastic and rigid two-link manipulators with one translational and two rotational joints.     

The Effect of the Elastic Compliance of Actuator Components on the Dynamics of a Robot

Kinematic and dynamic control problems for a pedestal-mounted robot with a multilink arm are formulated. The robot is considered a system of perfectly rigid bodies controlled by a combined actuating system. The mathematical model of robot dynamics accounts for the elastic properties of actuator components based on the formalism of Lagrange equations of the second kind. The effect of the elastic compliance of the actuator components on the dynamics of manipulator links and actuator motors is discussed. A robot with a two-link arm is considered as an example