软化桁架模型理论在钢筋煤矸石砼低剪力墙中的应用

本文通过对六榀试验钢筋煤矸石砼低剪力墙的分析研究，提出了煤矸石砼软化应力－应变曲线，并结合桁架模型理论，对其受力全过程进行了分析，结果表明，考虑其横向应变后的计算结果与试验结果吻合较好，最后，建议了一个钢筋煤矸石砼低剪力墙抗剪强度实用计算公式。     

软化桁架模型理论在钢筋煤矸石砼低剪力墙中的应用

本文通过对六榀试验钢筋煤矸石砼低剪力墙的分析研究，提出了煤矸石砼软化应力－应变曲线，并结合桁架模型理论，对其受力全过程进行了分析，结果表明，考虑其横向应变后的计算结果与试验结果吻合较好，最后，建议了一个钢筋煤矸石砼低剪力墙抗剪强度实用计算公式。     

砼受压全过程发射b值与分形维数的研究

声发射ｂ值反映了材料内部微裂缝发展，本文在ＭＴＳ试验系统进行了砼受压全过程实验同时，检测了砼声发射的幅值和事件数变化，并根据实验结果对ｂ值进行了研究。研究表明：在应力－应变全曲线峰值处ｂ值最小。此外，还根据分形理论对砼受压全过程分形维数进行了研究。     

金属材料的强度与应力–应变关系的球压入测试方法

压入法获取材料单轴应力–应变关系和抗拉强度对服役结构完整性评价有重要的基础意义.假定材料均匀连续、各向同性、应力应变关系符合Hollomon律,基于能量等效假定,即代表性体积单元(representative volume element, RVE)的von Mises等效和有效变形域内能量中值等效假定,本文提出了关联材料载荷、深度、球压头直径和Hollomon律的四参数半解析球压入(semi-analytical spherical indentation, SSI)模型.通过球压入载荷–深度试验关系获得材料的应力–应变关系和抗拉强度.考虑压入过程中的损伤效应,针对金属材料提出了用于球压入测试的材料弹性模量修正模型.对11种延性金属材料完成了球压入试验,采用本文提出的球压入试验方法测到的弹性模量、应力–应变关系和抗拉强度与单轴拉伸试验结果吻合良好.     

金属材料的强度与应力-应变关系的球压入测试方法

压入法获取材料单轴应力-应变关系和抗拉强度对服役结构完整性评价有重要的基础意义.假定材料均匀连续、各向同性、应力应变关系符合Hollomon律,基于能量等效假定,即代表性体积单元(representativevolume element, RVE)的vonMises等效和有效变形域内能量中值等效假定,本文提出了关联材料载荷、深度、球压头直径和Hollomon律的四参数半解析球压入(semi-analyticalspherical indentation,SSI)模型.通过球压入载荷-深度试验关系获得材料的应力-应变关系和抗拉强度.考虑压入过程中的损伤效应,针对金属材料提出了用于球压入测试的材料弹性模量修正模型.对11种延性金属材料完成了球压入试验,采用本文提出的球压入试验方法测到的弹性模量、应力-应变关系和抗拉强度与单轴拉伸试验结果吻合良好.      

砼受压全过程声发射b值与分形维数的研究

声发射ｂ值反映了材料内部微裂缝发展。本文在ＭＴＳ试验系统进行砼受压全过程实验同时，检测了硅声发射的幅值和事件数变化，并根据实验结果对ｂ值进行了研究。研究表明：在应力－应变全曲线峰值处ｂ值最小。此外，还根据分形理论对砼受压全过程分形维数进行了研究。     

砼受压全过程声发射特性及其损伤本构模型

本文根据在ＭＴｓ８１５．０２型电液伺服岩石与砼力学试验系统上完成的砼受压应力。应变全过程试验及相应声发射检测结果，分析了砼全过程的声发射特性，利用内变量理论建立了砼受压损伤本构模型。模型中的损伤因子可由相应声发射特性的损伤能相对比确定。经比较，所建模型与实验结果吻合较好。     

组织工程瓣的拉伸试验及力学参数的选取

一种全新的组织工程瓣膜的一维拉伸试验是研究其力学性能的基本方法。本文根据生物软组织粘弹性的理论和实验原理提出一维拉伸试验应包括预调、加载、卸载、定伸长下的应力松弛和断裂试验：确定了特征弹性模量E、变形恢复能力P、特征应力松弛速度R8、应力松弛的残值Ek、极限抗拉强度Tu和断裂伸长率λu作为特征参数。试图规范试验方法和试验参数的选取，以利于各种生物膜和组织工程瓣进行力学性能的相互比较。     

HKD-1型航空润滑油特征剪切应力及有效粘压系数确定的研究

在球盘式拖动力试验机上,对HKD-1型航空润滑油进行拖动力测量,给出了根据拖动力试验曲线的非线性上升段确定润滑油有效粘压系数和特征应力的方法,对HKD-1型航空润滑油在试验条件下的粘压系数和特征应力进行分析,并建立了其计算公式.结果表明:特征应力和有效粘压系数的求解方法简单合理,其计算公式的拟合精度较高,可为轴承动态特性设计提供计算依据;随着接触压力、入口油温和滚动速度增加,HKD-1型航空润滑油的特征应力增大,其粘压系数减小;滚动速度对特征应力和粘压系数的影响小于接触压力和入口油温.     

ZL303合金电磁热止裂后力学性能研究

利用自制的ZL-2超强脉冲放电装置对含有单边裂纹的ZL303合金试件进行电磁热止裂试验。通过微机控制电子万能试验机对止裂前后试件进行拉伸试验,并用SEM扫描电镜对断口进行观察,最后理论分析了受拉伸试件的应力强度因子。结果表明,电磁热止裂技术对ZL303具有良好的止裂效果;放电强化作用主要集中在裂尖附近,裂尖钝化形成焊口,裂尖处组织变细且强度提高,试件的抗拉强度平均提高了16.5%;电热应力强度因子削弱了拉应力所产生的应力强度因子,达到力学性能强化的效果。     

异质双材料粘接梁的界面端部应力及端部龟裂破坏的实验应力分析

本文采用了高灵敏度的云纹干涉法对异质双材料粘接梁在弯曲载荷作用下的位移进行了测量，用局部杂交法对界面端部区域的应变和应力进行了计算。通过对该区域内的实验应力分析发现：拉应力σｘ是影响结构强度的关键因素。本文还对在基体材料表面近角点区域可能出现的龟裂破坏的原因进行了分析。     

Stress analysis of an orthotropic material under diametral compression

The diametral compression test is commonly used to determine the tensile strength of brittle materials. For isotropic materials a simple relation based on specimen geometry and the applied load at failure is used to calculate the tensile strength. Previous to this work the effect of material orthotropy and material orientation on the specimen stress state had not been completely determined. In this study, both isotropic and orthotropic specimens were analyzed using a finite element analysis and experimentally verified by strain gage and photoelastic measurements. Further, this work investigated the effect of the applied load area on the specimen stress state. Results of this work show that there is a significant difference between the theoretical calculations based on the assumption of material isotropy when compared to an orthotropic material. This difference can be as much as 45 percent depending on the degree of orthotropy and the orientation. It was also determined that the applied load area and material orientation significantly influence the specimen stress state. An applied load area of 8 percent of the circumference was found to reduce the stresses in the applied load region.     

Crack tip field in a linear elastic–plastic strain-hardening material

The strip necking model for strain-hardening materials is studied in this paper, in which the stress distributed over the strip necking zone is assumed to be ultimate stress. The bi-linear stress–strain relation which can model certain features of plastic flow is adopted in this model. The stress and strain fields are calculated based on this model in this paper. The size of the strip necking region is determined by balancing the stress intensity factor due to remote loading with that due to assumed closing forces equal to the ultimate tensile strength of the material distributed over the strip necking zone. It is interesting that the strip necking region size and the crack tip opening displacement depend not only on the remote load, but also the material hardening parameters, which is different from the results of strip yield model. The results agree with experiments well, and the model has wider application.     

16MnR钢缺口试样解理断裂行为研究

研究了低合金热轧钢16MnR缺口试样在$-196\,{^\circ}$C和$-130\,{^\circ}$C的解理断裂机 理. 拉伸试验、单、双缺口四点弯曲实验、断口形貌观察以及有限元分析结果表明, 缺口试 样发生解理断裂时均起裂于夹杂物粒子, 一种位于缺口根部前端(IC型), 另一种位于距缺口 根部较远的条形裂纹前端(SIC型); 且随温度升高, 起裂源的类型从$-196\,{^\circ}$C下的IC 型转变为$-130\,{^\circ}$C下的SIC型. 微裂纹均形核于夹杂物, 最终的断裂由铁素体晶粒尺 寸的微裂纹扩展控制. 缺口试样IC型解理断裂遵循裂纹形核条 件$\varepsilon_{\rm p} \ge \varepsilon_{\rm pc}$和裂纹扩展条件$\sigma_{yy} \ge \sigma_{f}$, 而SIC型解理断裂条件则演化为$\varepsilon_{\rm p}+\varepsilon_{\rm ps} \ge \varepsilon_{\rm pc}$和$\sigma_{yy} +\sigma_{yy{\rm s}} \ge \sigma_{f}$.     

Prestressing effect of twisted fiber yarn in composites

By utilizing the behavior of twisted fiber yarn, prestressing composites can be made. In unloading, the matrix of the prestressing composite is applied in compression. If tensile load acts on the composite, the value of the tensile stress acting on the materials may decrease greatly. By twisted fiber yarn, therefore, the tensile strength of the composites can be improved. An analysis for extension of continuous fiber yarns is made here and residual stress after curing is taken into account. The prestressing intensity in the composite depends on the twist of fiber yarn. The photoelastic test and the analysis of electron micrograph are performed, and the theoretical method for calculating prestressing effect is presented in this paper.     

Flattened Brazilian Disc Method for Determining the Dynamic Tensile Stress-Strain Curve of Low Strength Brittle Solids

An indirect tensile testing method is proposed to measure the full dynamic tensile stress-strain curve of low strength brittle solids. In this method, the flattened-Brazilian disc (FBD) sample is loaded by modified split Hopkinson pressure bars (SHPB) system. Low amplitude dynamic forces were measured with a pair of piezoelectric force transducers embedded in the incident bar and the transmitted bar. The evolution of tensile stress at the center of the disc sample was determined through finite element analyses using the measured stress in SHPB as inputs. In a traditional Brazilian test, a strain gauge is mounted at the center of the specimen to measure the tensile strain, which is difficult to apply for low strength brittle materials. Thus, two types of non-contact methods, the Digital Image Correlation (DIC) technique and the Laser Gap Gauge (LGG), were used to measure the strain. The DIC method was used to monitor the displacement and the strain map of the specimen during the test, from which the strain at the center of the specimen can be obtained. The accuracy of the DIC results was assessed, and the displacement and strain uncertainties of our system were 0.003 mm and 0.003, respectively. LGG was used to monitor the expansion of the disc perpendicular to the loading axis, from which the average tensile strain is deduced. The numerical simulation revealed that the tensile strain at the center of the specimen is proportional to the average tensile strain and that the ratio is not sensitive to the material elastic parameters. The strain measured through LGG was compared with that measured by the DIC method using photos captured with a synchronized high-speed camera. The result of the LGG method was 20 % smaller than that of the DIC process. However, the latter was limited by the number of frames of the high-speed camera. The feasibility of this methodology was demonstrated using a polymer-bonded explosive (PBX).     

复合材料中加捻纤维束的预应力效应

利用加捻纤维束的力学性能,可以制成预应力复合材料.在不受外力的情况下,这种复合材料的基体受压应力的控制.当有拉伸力作用的时候,材料所受的拉应力值会大大减少,这样,利用这种现象可以提高纤维增强复合材料的抗拉强度.本文将分析连续的加捻纤维束受拉状况并考虑到材料固化后产生的残余应力的影响.这种方法所产生的预应力取决于纤维束的加捻程度.本文将给出计算这种预应力的方法,而且还提供加捻纤维束产生预应力的光弹测试结果以及这种纤维预应力复合材料的纤维破坏的特征.     

不同加载边界下混凝土巴西劈裂过程及强度的DIC实验分析

平板、垫条、圆弧压模及平台试样等不同加载方式下, 脆性材料巴西劈裂实验结果的差异一直是人们所讨论的问题. 本文设计了混凝土平板直接加载与采用垫条加载实验, 采用理论、高速相机与数字图像相关法(digital image correlation, DIC)相结合的方法, 对试样表面应变场演化、起裂位置及裂纹扩展过程进行分析, 探讨了不同的加载边界对试样应变集中演化及劈裂拉伸强度结果的影响. 结果显示: (1)混凝土拉伸非线性特性导致的应变集中演化对不同加载条件非常敏感, 平板加载时应变集中较早在加载端起始并向中心演化, 即使满足巴西实验"中心起裂"条件, 其强度仍低于垫条加载情况, 两者差别达17.9%; (2)如果软垫条加载接触角合理设计, 与平板直接加载相比, 其应力场更稳定, 有利于保证圆盘试样的应变集中及断裂均从中心起始, 更好满足巴西劈裂实验条件; (3)仅校验巴西实验 "中心起裂"有效性条件是不充分的, 设计时必须谨慎考虑. 研究结果对脆性材料巴西劈裂实验设计、测试分析具有重要参考意义.      

Determining Stress–Strain in Rubber with In-Plane Biaxial Tensile Tester

The nominal stress–strain relationships of industrial rubber materials under multiaxial deformation are essential for precisely determining the constitutive laws of those materials. This paper proposes a new method for precisely estimating the nominal stress–stretch relationships of carbon-black-filled styrene butadiene rubbers (SBRs) under uniaxial tension, pure shear, and equibiaxial tension by using an in-plane biaxial tensile tester. The proposed method employs sheet-shaped rubber samples with notches for the pure-shear and equibiaxial tension tests to mitigate the influence of non-uniform deformation around the clamps. Finite element analysis and biaxial tensile tests were performed to verify the effectiveness of the proposed method. Performance evaluations based on both numerical calculations and experiments revealed that the proposed method enabled the precise calculation of the nominal stress–stretch relationship for uniform deformation from a tensile load and deformation of the reference area defined at the center of the samples.     

评估TiN薄膜与基材结合的划痕试验及有限元模拟

通过有限元模型模拟划痕试验得到的结果表明∶切应力的起伏变化?膜/基界面处切应力差值?接触区附近膜层表面张应力?高载下的几种应力集中等,对膜/基体系的失效都有重要的作用.通过模型计算临界载荷下的膜/基界面处切应力差值,可用来评价膜层与基材的结合强度;提出了划痕试验中膜/基体系失效的2种机制.不同性能基材的TiN膜/基体系划痕试验结果,可验证本文有限元模拟的有效性,并表明临界载荷是膜/基结合强度?体系承载能力?内聚结合性能等的综合反映;低载往复摩擦磨损试验的结果进一步证实,用划痕试验的临界载荷评估膜/基结合强度具有局限性.