Numerical investigation of ${\rm H}_2$ injection in Mach 5 air flow with a strong shock/boundary layer interaction

A numerical study of the hydrogen injection has been investigated in a flow configuration obtained from the interaction of two axisymmetric oblique shock waves produced by a conical ring and a centre-body. This configuration, due to a strong shock/boundary layer interaction, was named a viscous mach interaction (VMI). The geometry which leads to this configuration can be used as a hypersonic inlet, and as this inlet could be axisymmetric or two-dimensional, a first result was to show that this VMI configuration exists in both cases. Different injection locations in the subsonic zone are tested in order to keep this VMI configuration . The influence of the hydrogen injection on the mixing flow behavior is analyzed. The numerical results show that the equivalence ratio of the gas-mixture is high enough in order to have a non-reactive gas close to the wall which keeps constant the hydrogen temperature along the centre-body. Thus, the hydrogen injection can play the role of a forward-facing jet reducing heat-transfer at the centre-body wall.     

Separation control in a conical diffuser with an annular inlet: center body wake separation

In many practical applications of conical diffusers, the flow is fed by an annular flow passage formed by a center body. Flow separation, which occurs if the center body ends abruptly, is undesirable because it degrades the diffuser performance. The present experiment utilizes magnetic resonance velocimetry to acquire three-component mean velocity measurements for a set of conical diffusers with an annular inlet. The results show strong coupling between the diffuser wall boundary layer development and the wake of the center body. Coanda blowing is used to mitigate the center body wake separation. The diffuser wall boundary layer is thick in the absence of the central separation bubble and separates when Coanda blowing is too strong.     

Method of mean-mass parameters for a three-dimensional boundary layer in a flow with vorticity

When a gas flows with hypersonic velocity over a slender blunt body, the bow shock induces large entropy gradients and vorticity near the wall in the disturbed flow region (in the high-entropy layer) [1]. The boundary layer on the body develops in an essentially inhomogeneous inviscid flow, so that it is necessary to take into account the difference between the values of the gas parameters on the outer edge of the boundary layer and their values on the wall in the inviscid flow. This vortex interaction is usually accompanied by a growth in the frictional stress and heat flux at the wall [2, 3]. In three-dimensional flows in which the spreading of the gas on the windward sections of the body causes the high-entropy layer to become narrower, the vortex interaction can be expected to be particularly important. The first investigations in this direction [4–6] studied the attachment lines of a three-dimensional boundary layer. The method proposed in the present paper for calculating the heat transfer generalizes the approach realized in [5] for the attachment lines and makes it possible to take into account this effect on the complete surface of a blunt body for three-dimensional laminar, transition, or turbulent flow regime in the boundary layer.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 80–87, January–February, 1981.     

Numerical study of adverse pressure gradient generation over a flat plate using a rotating cylinder

Generating an adverse pressure gradient (APG), using a rotating cylinder in the proximity of a plane wall under a laminar freestream flow, is studied numerically in this work. The magnitude of the generated APG is a function of the gap, G, between the cylinder and the wall, and the rotational speed of the cylinder, Ω. The flow in such a configuration is characterized by periodic transient vortex shedding at high Reynolds number. A numerical model for the computation of the transient flow for this configuration is developed using the ANSYS CFD simulation tool. The model is validated against published experimental and numerical data for similar flow configurations and excellent agreement is observed. A parametric study is carried out for different combinations of G and Ω for two different Reynolds numbers of 200 and 1000 to examine the development of the resulting separation bubble due to the generated APG. The mechanism of the boundary layer separation over the plane wall and the corresponding wake dynamics is investigated. Results are presented in terms of the distribution of the pressure coefficient as well as skin friction coefficient along the wall and flow patterns around and downstream of the cylinder in the proximity of the wall. The results of these computations confirm that using a rotating cylinder over a plane wall in a freestream flow is an effective technique to generate a controlled range of adverse pressure gradients.     

Effect of boundary layer on Mach reflection over a wedge surface

Abstract. In this paper, we consider the phenomenon of unsteady Mach reflection generated by a plane shock wave advancing over a straight wedge surface, with particular attention to the deviation of the flow field from the self-similar nature. We examine the observed change in angle between incident and reflected shocks, which is in contrast to the fact that the angle should remain constant with time in a self-similar flow. The effect of the boundary layer behind the advancing shock wave over the surface of the wedge is considered to cause this, and boundary layer theory is utilized to estimate the thickness of the layer. It is found that the thickness increases as to the time t compared with t by the overall expansion in the self-similar flow. Assuming that the thicker boundary layer is effectively equivalent to a change in wedge angle, the effect of the boundary layer on the flow field should be less in later stages with larger t values in accordance with the observation above. Received 6 March 2000 / Accepted 23 April 2001     

Free interaction of a three-dimensional boundary layer with an exterior irrotational flow

Asymptotic equations describing the unsteady free interaction of a three-dimensional boundary layer with an exterior flow are derived. The orders of the independent variables and perturbations of the flow parameters are chosen in such a way that the pressure gradient that occurs in the equation of the wall layer is due to the displacement of streamlines situated near the surface of the body. The Fourier method is used to construct a solution to the linearized problem. A class of perturbations satisfying homogeneous boundary conditions on the surface of the body is found.     

The laminar boundary layer near a body corner point

A method is developed for calculating the characteristics of a laminar boundary layer near a body contour corner point, in the vicinity of which the outer supersonic stream passes through a rarefaction flow. In the study we use the asymptotic solution of the Navier-Stokes equations in the region with large longitudinal gradients of the flow functions for large values of the Reynolds number, the general form of which was used in [1].The pressure, heat flux, and friction distributions along the body surface are obtained. For small pressure differentials near the corner the solution of the corresponding equations for small disturbances is obtained in analytic form.The conventional method for studying viscous gas flow near body surfaces for large values of the Reynolds number is the use of the Prandtl boundary layer theory. Far from the body the asymptotic solution of the Navier-Stokes equations in the first approximation reduces to the solution of the Euler equations, while near the body it reduces to the solution of the Prandtl boundary layer equations. The characteristic feature of the boundary layer region is the small variation of the flow functions in the longitudinal direction in comparison with their variation in the transverse direction. However, in many cases this condition is violated.The necessity arises for constructing additional asymptotic expansions for the region in which the longitudinal and transverse variations of the flow functions are quantities of the same order. The general method for constructing asymptotic solutions for such flows with the use of the known method of outer and inner expansions is presented in [1].In the following we consider the flow in a laminar boundary layer for the case of a viscous supersonic gas stream in the vicinity of a body corner point. Behind the corner the flow separates from the body surface and flows around a stagnant zone, in which the pressure differs by a specified amount from the pressure in the undisturbed flow ahead of the point of separation. A pressure (rarefaction) disturbance propagates in the subsonic portion of the boundary layer upstream for a distance which in order of magnitude is equal to several boundary layer thicknesses. In the disturbed region of the boundary layer the longitudinal and transverse pressure and velocity disturbances are quantities of the same order. In this study we construct additional asymptotic expansions in the first approximation and calculate the distributions of the pressure, friction stress, and thermal flux along the body surface.     

Development of slow disturbances in a hypersonic boundary layer

The mechanisms of development of slow time-dependent disturbances in the wall region of a hypersonic boundary layer are established and a diagram of the disturbed flow patterns is plotted; the corresponding nonlinear boundary value problem is formulated for each of these regimes. It is shown that the main factors that form the disturbed flow are the gas enthalpy near the body surface, the local viscous-inviscid interaction level, and the type, either subsonic or supersonic, of the boundary layer as a whole. Numerical and analytical solutions are obtained in the linear approximation. It is established that enhancement of the local viscous-inviscid interaction or an increased role for the main supersonic region of the boundary layer makes the disturbed flow by and large “supersonic”: the upstream propagation of the disturbances becomes weaker, while their downstream growth is amplified. Contrariwise, local viscous-inviscid interaction attenuation or an increased role for the main subsonic region of the boundary layer has the opposite effect. Surface cooling favors an increased effect of the main region of the boundary layer while heating favors an increased wall region effect. It is also found that in the regimes considered disturbances travel from the turbulent flow region downstream of the disturbed region under consideration counter to the oncoming flow, which may be of considerable significance in constructing the nonlinear stability theory.     

Combined effects of rotation and translation on a MHD flow due to compressible viscous fluid

Summary The modification of an axi-symmetric viscous flow due to a relative rotation of a disk or fluid by a translation of the boundary are studied. The fluid is taken to be compressible and electrically conducting. The equations governing the motion are solved iteratively through a central-difference scheme. The effect of an axial magnetic field and disk temperature on the flow and heat transfer are included in the present analysis. The translation of the disk or fluid generates a velocity field at each plane parallel to the disk (secondary flow). The cartesian components of the velocity due to the secondary flow are oscillatory in nature when a rigid body rotation of the free stream along with a translation of the disk is considered. The magnetic field damps out the velocity field, and reduces the thickness of the boundary layer. The cross component of wall shear due to secondary flow acts in a direction opposite to the rotation of the disk or fluid for all cases of the motion. The rise in disk temperature produces an increment in the magnitude of the wall shear associated with the secondary flow.     

Heat transfer on a cylinder in accelerated slip flow

The axisymmetric laminar boundary layer flow along the entire length of a semi-infinite stationary cylinder under an accelerated free-stream is investigated. Considering flow at reduced dimensions, the boundary layer equations are developed with the conventional no-slip boundary condition for tangential velocity and temperature replaced by a linear slip-jump boundary condition. Asymptotic series solutions are obtained for the heat transfer coefficient in terms of the Nusselt number. These solutions correspond to prescribed values of the momentum and temperature slip coefficients and the index of acceleration. Heat transfer at both small and large axial distances is determined in the form of series solutions; whereas at intermediate distances, exact and interpolated numerical solutions are obtained. Using these results, the heat transfer along the entire cylinder wall is evaluated in terms of the parameters of acceleration and slip.     

Numerical solution of a boundary layer problem on a nonconducting surface of an MHD channel

The problem of boundary layer flow on a nonconducting wall has been considered in [1–3]. Therein, it was assumed that either the problem is self-similar [1], or the solution was found in the form of a power series in a small parameter [2,3]. The objective of these assumptions is to reduce the boundary layer equations to ordinary differential equations. In the present work the problem is solved without making these assumptions. The distribution along the channel length of the frictional resistance and heat transfer coefficients on the wall are obtained, and the variation of these coefficients with the load parameter is studied.     

Interaction of a Traveling Pressure Perturbation with a Boundary Layer

The interaction between a traveling pressure perturbation and a laminar compressible boundary layer is investigated for a perturbation level higher than that needed to initiate steady-state flow separation. It is found that if the velocity of the pressure perturbation is fairly high the flow may remain unseparated and its direction of motion determines the nature of the perturbation propagation in the boundary layer. It is shown that even in the linear approximation the perturbations are mainly induced by the linear wall layer and not by the critical layer, which always remains nonlinear. It is also found that in the unsteady case shortwave perturbation oscillations are damped with time while the longwave ones grow and that the growth of the perturbations with time amplifies their damping along the streamwise coordinate while damping reduces it.     

Effect of a Thin Longitudinal Inviscid Vortex on a Two-Dimensional Pre-Separation Boundary Layer

For large Reynolds numbers, an asymptotic solution of the Navier-Stokes equations describing the effect of a thin longitudinal vortex with a constant circulation on the development of an incompressible steady two-dimensional laminar boundary layer on a flat plate is obtained. It is established that, in a narrow wall region extending along the vortex filament, the viscous flow is described by the 3-D boundary layer equations. A solution of these equations for small values of the vortex circulation is studied. It is found that the solution of the two-dimensional pre-separation boundary layer equations collapses. This is attributable to the singular behavior of the 3-D disturbances near the zero-longitudinal-friction points.     

Wall shear stress measurement in a turbulent pipe flow using ultrasound Doppler velocimetry

A turbulent boundary layer of a water flow is investigated by means of pulsed ultrasound Doppler velocimetry. The advantage of this method is the acquisition of complete velocity profiles along the sound propagation line within very short time intervals. The shear stress velocity, used for normalizing the velocity profiles, was determined by fitting the profiles to the universal profiles in a turbulent boundary layer obtained from Prandtl's mixing length theory. A coordinate transformation in the near-wall region is proposed to allocate the velocity data to "true" wall distances. From the experimental values of the wall shear stress velocity, the friction factors for a turbulent pipe flow are calculated and compared to the Blasius law. The overall error in measurement was estimated to NJ.4%.     

Liquid metal flow in a simple manifold with a strong transverse magnetic field

This paper treats a liquid-metal flow through a simple manifold connecting one duct to two parallel ducts. The manifold consists of an infinitely long, constant-area, rectangular duct with a uniform, transverse magnetic field and with a semi-infinite middle wall at the plane of symmetry which is perpendicular to the magnetic field. The magnetic flux density is sufficiently large that inertial effects can be neglected everywhere and that viscous effects are confined to boundary layers and to an interior layer along the magnetic field lines through the end of the middle wall. The purpose of this paper is to illustrate an approach with eigenfunction expansions which will be useful for manifolds with many parallel ducts. In the present simple manifold, the principal three-dimensional effect is a transfer of flow to the inviscid core region from the high-velocity jets adjacent to the sides which are parallel to the magnetic field. There is also an important redistribution of flow along magnetic field lines inside the side-wall boundary layers.     

Similarity solutions of the equations of a boundary layer in a nonuniform external flow

Similarity solutions of the equations of a laminar incompressible boundary layer, formed in a rotational external flow, are investigated. Such problems arise in the analysis of the flow in a boundary layer when there is an abrupt change in the boundary conditions (for example, in the case of a discrete inflation of the boundary layer, in hypersonic flow about blunt bodies, etc.). Various approaches to their solution have been proposed earlier in [1–4]. Solved below is the so-called inverse problem of boundary layer theory (see [3], p. 200), where the contour of the body that causes a given flow outside the boundary layer is unknown beforehand and is found during the course of solution of the problem in connection with the coupling of the longitudinal and transverse velocity components. The cases of a parabolic (u_e ~ y²) and a linear (u_e=a(x)+b(x)y) variation in the velocity of the external flow with distance along the transverse direction are considered in detail. The latter includes an investigation of the flow in the neighborhood of the critical point of a blunt body, taking account of the vorticity of the flow in the shock layer.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 78–83, March–April, 1971.     

Asymptotic theory of the Boltzmann system,for a steady flow of a slightly rarefied gas with a finite Mach number: General theory

A steady rarefied gas flow with Mach number of the order of unity around a body or bodies is considered. The general behaviour of the gas for small Knudsen numbers is studied by asymptotic analysis of the boundary-value problem of the Boltzmann equation for a general domain. The effect of gas rarefaction (or Knudsen number) is expressed as a power series of the square root of the Knudsen number of the system. A series of fluid-dynamic type equations and their associated boundary conditions that determine the component functions of the expansion of the density, flow velocity, and temperature of the gas is obtained by the analysis. The equations up to the order of the square root of the Knudsen number do not contain non-Navier–Stokes stress and heat flow, which differs from the claim by Darrozes (in Rarefied Gas Dynamics, Academic Press, New York, 1969). The contributions up to this order, except in the Knudsen layer, are included in the system of the Navier–Stokes equations and the slip boundary conditions consisting of tangential velocity slip due to the shear of flow and temperature jump due to the temperature gradient normal to the boundary.     

Application of PIV in a Mach 7 double-ramp flow

The flow over a two-dimensional double compression ramp configuration is investigated by means of schlieren visualization, quantitative infrared thermography and particle image velocimetry (PIV) in a short-duration facility producing a free-stream flow at Mach 7. The study focuses upon the accuracy assessment of PIV in the hypersonic flow regime including flow facility effects such as repeatability of test conditions. The solid tracer particles are characterized by means of electron microscopy as well as by measuring the dynamic response across a planar oblique shock wave with PIV. The experiments display a strong variation in the light scattering intensity of the seeded flow over the flow field, due to the large flow compressibility. The mean velocity spatial distribution allows to clearly identify the shock pattern and the main features of the flow downstream of the shocks. However, the spatial resolution is insufficient to determine the wall flow properties. Furthermore the velocity data obtained with the PIV technique allow the determination of the spatial distribution of the Mach number under the hypothesis of adiabatic flow. The double ramp configuration with a variable second compression angle exhibits shock–shock interactions of Edney type VI or V for the lowest and highest ramp angle, respectively. A single heat transfer peak is detected with infrared thermography on the second ramp in case of a type VI interaction while for the type V shock interaction a double heat transfer peak is found. Shock wave angles measured with PIV are in good agreement with theory and the overall flow topology is consistent with schlieren visualization. Also in this respect the results are in agreement with compressible flow theory.     

Bulk flow parameters in turbulent wall boundary layers near separation

Experiments were conducted in a turbulent boundary layer near separation along a flat plate. The pressure gradient in flow direction was varied such that three significant boundary layer configurations could be maintained. The flow in the test section thus had simultaneously a region of favourable pressure gradient, a region of strong adverse pressure gradient with boundary layer separation and a region of reattached boundary layer. Specially designed fine probes facilitated the measurements of skin friction and velocity distribution very close to the wall. Bulk flow parameters such as skin friction coefficient C _f, Reynold's number Re_δ2 and shape factors H and G, which are significant characteristics of wall boundary layers were evaluated. The dependence of these parameters on the Reynolds number and along the test section was explored and the values were compared with other empirical and analytical formulae known in the literature.     

Mechanism of compressor airfoil boundary layer flow control using nanosecond plasma actuation

The flow control effects of nanosecond plasma actuation on the boundary layer flow of a typical compressor controlled diffusion airfoil are investigated using large eddy simulation method. Three types of plasma actuation are designed to control the boundary layer flow, and two mechanisms of compressor airfoil boundary layer flow control using nanosecond plasma actuation have been found. The plasma actuations located within the laminar boundary layer flow can induce a small vortex structure through influencing on the density and pressure of the flow field. As the small vortex structure moves downstream along the blade surface with the main flow, it can suppress the turbulent flow mixing and reduce the total pressure loss. The flow control effect of the small vortex structure is summarized as wall jet effect. Differently, the plasma actuation located within the turbulent boundary layer flow can act on the shear layer flow and induce a large vortex structure. While moving downstream, this large vortex structure can suppress the turbulent flow mixing too.