Modelling the time dependent flow over riblets in the viscous wall region

The flow over riblets is examined computationally using a time dependent model of the viscous wall region. This 2 1/2 D model, developed by Hatziavramidis and Hanratty (1979) and modified by Nikolaides (1984) and Chapman and Kuhn (1981, 1986) assumes homogeneity in the streamwise direction so that the flow is solved only in the cross-sectional plane. The flow at the upper boundary of the computational domain (y ⁺ 40) is described using a streamwise eddy model consisting of two scales, one of the streak spacing (⁺ 100), which dominates vertical momentum transport, and a larger scale that accounts for the influence of large outer flow eddies.The protrusion height concept (Bechert and Bartenwerfer, 1989) is used to define ay ⁺=0 location for surfaces with riblets. A control volume finite element method utilizing triangular meshes is used to exactly fit the riblet cross-sectional geometry. Results obtained using fairly large riblets compare well with the limited experimental evidence available. Observations of the transient flow suggest that the riblets interact with the near-wall streamwise vortices, weakening them by the generation of intermittent secondary vortices within the riblet valleys. The riblets also appear to limit the lateral spread of inrushes towards the wall and retain low momentum fluid in the riblet valleys effectively isolating much of the wall from such inrushes.     

Drag measurements on V-grooved surfaces on a body of revolution in axial flow

In water flows with velocities of up to 9 m/s the friction drag of a body of revolution in axial flow was investigated for dependence on the body surface structure. This was done for different types of riblet film fixed on the surface with the riblet direction aligned with the flow. The lateral spacing between the triangular shaped riblets varied between 0.033 mm and 0.152 mm. In all cases the riblet spacing was equal to the riblet height. For comparison a smooth reference film was used.Depending on the Reynolds number and the non-dimensional riblet spacings ⁺, a turbulent drag reduction of up to 9% could be achieved with riblets in comparison with the flow over a smooth surface.In the region of transition to turbulent flow and with non-dimensional riblet spacings ofs ⁺10–15 drag reductions of up to 13% were obtained. It is therefore conjectured, that in addition to hampering the near wall momentum exchange, the riblets can delay the development of initial turbulent structures in time and space.     

Riblet drag reduction in mild adverse pressure gradients: A numerical investigation

Riblet films are a passive method of turbulent boundary layer control that can reduce viscous drag. They have been studied with great detail for over 30 years. Although common riblet applications include flows with Adverse Pressure Gradients (APG), nearly all research thus far has been performed in channel flows. Recent research has provided motivation to study riblets in more complicated turbulent flows with claims that riblet drag reduction can double in mild APG common to airfoils at moderate angles of attack. Therefore, in this study, we compare drag reduction by scalloped riblet films between riblets in a zero pressure gradient and those in a mild APG using high-resolution large eddy simulations. In order to gain a fundamental understanding of the relationship between drag reduction and pressure gradient, we simulated several different riblet sizes that encompassed a broad range of s⁺ (riblet width in wall units), similarly to many previously published experimental studies. We found that there was only a slight improvement in drag reduction for riblets in the mild APG. We also observed that peak values of streamwise turbulence intensity, turbulent kinetic energy, and streamwise vorticity scale with riblet width. Primary Reynolds shear stresses and turbulence kinetic energy production however scale with the ability of the riblet to reduce skin-friction.     

On near-wall turbulence-generating events in a turbulent boundary layer on a riblet surface

The boundary layer over a drag reducing riblet surface is investigated using hot-wire anemometry and flow visualisation. The concept of a riblet sublayer is introduced, and a definition is proposed in terms of a region of reduced turbulence energy production formed near the wall by the addition of riblets. The hot wire records are examined using a modified form of quadrant analysis, and results obtained over plain and riblet surfaces are compared. Close to the wall, the addition of riblets produces a marked reduction in the occurrence of ejection (2nd quadrant) events. A corresponding increase in the incidence of sweep (4th quadrant) events is accompanied by the development of a strong tendency toward a preferred event duration, and a preferred interval between events. These changes diminish rapidly with distance from the surface, becoming almost undetectable beyondy ⁺=40. They are discussed in the light of flow visualisation results, and interpreted in terms of mechanisms associated with the interaction between the riblets and the inner boundary layer flow structures. A conceptual model of the flow mechanisms in the riblet sublayer is proposed.     

Flow field analysis of a turbulent boundary layer over a riblet surface

The near-wall flow structures of a turbulent boundary layer over a riblet surface with semi-circular grooves were investigated experimentally for the cases of drag decreasing (s ⁺=25.2) and drag increasing (s ⁺=40.6). One thousand instantaneous velocity fields over riblets were measured using the velocity field measurement technique and compared with those above a smooth flat plate. The field of view was 6.75 × 6.75 mm² in physical dimension, containing two grooves. Those instantaneous velocity fields were ensemble averaged to get turbulent statistics including turbulent intensities and turbulent kinetic energy. To see the global flow structure qualitatively, flow visualization was also carried out using the synchronized smoke-wire technique under the same experimental conditions. For the case of drag decreasing (s ⁺=25.2), most of the streamwise vortices stay above the riblets, interacting with the riblet tips frequently. The riblet tips impede the spanwise movement of the streamwise vortices and induce secondary vortices. The normalized rms velocity fluctuations and turbulent kinetic energy are small near the riblet surface, compared with those over a smooth flat plate. Inside the riblet valleys, these are sufficiently small that the increased wetted surface area of the riblets can be compensated. In addition, in the outer region (y ⁺ > 30), these values are almost equal to or slightly smaller than those for the smooth plate. For the case of drag increasing (s ⁺=40.6), however, most of the streamwise vortices stay inside the riblet valleys and contact directly with the riblet surface. The high-speed down-wash flow penetrating into the riblet valley interacts actively with the wetted riblet surface and increases the skin friction. The rms velocity fluctuations and turbulent kinetic energy have larger values compared with those over a smooth flat plate. Received: 24 March 1999/Accepted: 10 March 2000     

Numerical Simulation of Riblet Controlled Spatial Transition in a Zero-Pressure-Gradient Boundary Layer

To analyze the fundamental physical mechanism which determines the damping effect of a riblet surface on three-dimensional transition several numerical simulations of spatial transition in a flat plate zero-pressure-gradient boundary layer above a riblet wall are performed in this study. Two types of forced transition scenarios are investigated. The first type of transition is defined by K-type transition induced by a dominant two-dimensional Tollmien–Schlichting (TS) wave and a weak spanwise disturbance. The second type of transition is purely excited by two oblique waves. By a qualitative analysis of the occurring maximum wall-normal and spanwise velocity components and the Fourier modes of the disturbances the two-dimensional TS waves are found to be amplified by riblets, whereas three-dimensional structures, i.e., Λ-, hairpin, and streamwisely aligned vortices, are damped. At oblique transition the breakdown to turbulence is delayed by the riblets compared to transition on a clean surface. The investigation of the near wall flow structure reveals secondary flows induced by the riblets and reduced wall normal ejections as well as a reduced downwash.     

Flow over convergent and divergent wall riblets

Fast swimming sharks have small riblets on their skin, which are assumed to improve the swimming performance of the fish. Fluid dynamic experiments in water as well as in air confirm this assumption. With riblet surfaces as compared to smooth surfaces, drag reductions up to about 10% were measured. The overall riblet pattern on sharks shows parallel riblets directed from head to tail, but besides this overall pattern fast swimming sharks have also small areas with converging riblets and others with diverging riblets. In the present study the velocity field over convergent and divergent riblet patterns is investigated by hot-wire measurements in turbulent pipe flow. Significant changes in the near wall velocity field were found.     

Drag characteristics of longitudinal and transverse riblets at low dimensionless spacings

A surface grooved with microscopic riblets aligned parallel to the flow is an effective means to reduce the turbulent skin friction up to 10% compared to a smooth surface. The maximum drag reduction is found for a dimensionless rib spacing s ⁺ in the range of 15–17. For s ⁺ < 10, a linear behaviour of the drag reduction curve is predicted by viscous theory. This linear slope of the drag reduction curve is in contradiction to Schlichting’s postulation of a hydraulically smooth behaviour of small-scale roughness in a turbulent flow. This regime of evanescent dimensionless rib spacings is investigated experimentally by direct wall shear stress measurements in a fully developed channel flow. Additionally, a numerical calculation of the viscous flow over riblets was carried out to predict the drag reducing behaviour. The experimental results show a linear drag reducing behaviour down to s ⁺ = 0.3, which is in good agreement with the numerical results of the viscous simulation. The postulation of Schlichting’s hydraulically smooth regime of a rough surface was not confirmed, neither for a riblet surface nor for a surface geometry with grooves oriented perpendicular to the flow. In the latter case, the drag increases as a quadratic function of the roughness height.     

The effect of riblets on laminar to turbulent transition

Experiments conducted on the effect of riblets on the laminar-to-turbulent transition of a flat plate in a water tunnel are reported. Transition was determined using a Laser Doppler Velocimeter (LDV). A smooth reference surface was compared to five riblet surfaces for a range of Reynolds numbers. Smooth surface transition Reynolds number was about 2.75 × 10⁶. All of the five tested riblet surfaces had lower transition Reynolds numbers. A critical roughness Reynolds number of about 6 was determined for one of the riblet surfaces. This is much lower than the generally accepted value of 25, considered safe for distributed roughness.     

湍流流动中鲨鱼皮表面流体减阻研究进展

快速游动的鲨鱼, 其皮肤表面沿流动方向有序地排列着沟槽状结构, 人们认为这种结构能在湍流流动 中减小表面摩擦阻力. 人们仿真这种生物结构来进行实验研究和应用, 通过复制和改善鲨鱼皮肤表面沟槽状 结构, 使得摩擦阻力最大减小了近10%. 在实验和模拟仿真中, 人们不断讨论和研究湍流流动阻力的形成机制 和沟槽减阻的理论特性. 本文综述了沟槽减阻理论特性的一些研究方法, 并且归纳定义了沟槽减阻最优几何 形状及其尺寸; 详细考虑流体流动的特点, 给出了一种用来选择最优沟槽形状及其尺寸的方法; 综述了目前的 沟槽加工制造技术. 由于鲨鱼皮肤表面存在少量黏液, 从仿生学的角度, 文章最后综述并展望了通过局部应用 疏水性材料来改变沟槽附近流场属性, 从而达到更大程度上减小阻力的目标.      

Tests of drag-reducing polymer coated on a riblet surface

Experiments have been carried out at BMT where the drag reduction due to Hoechst U-groove riblets, a polymer coating, and the two combined were measured in a towing tank on a one-third scale model of the America's Cup winning yacht, Australia II. The results indicated that the riblet/polymer combination offered an overall improvement in drag reduction characteristics over either riblets or polymer coating alone, with a maximum reduction of 3.5% observed for a non-dimensional S ⁺=8. The qualitative behaviour of the drag reduction was similar to that recorded in earlier pipe flow experiments, employing an injection of polymer additive and 3M V-groove riblets, but contrary to that recorded in studies of an axisymmetric body, also coated with 3M riblets, in a drop tank filled with a polymer solution.     

Large-scale spanwise periodicity in a turbulent boundary layer induced by highly ordered and directional surface roughness

The effect of converging–diverging riblet-type surface roughness (riblets arranged in a ‘herringbone’ pattern) are investigated experimentally in a zero pressure gradient turbulent boundary layer. For this initial parametric investigation three different parameters of the surface roughness are analysed in detail; the converging–diverging riblet yaw angle α, the streamwise fetch or development length over the rough surface F_x and the viscous-scaled riblet height h⁺. It is observed that this highly directional surface roughness pattern induces a large-scale spanwise periodicity onto the boundary layer, resulting in a pronounced spanwise modification of the boundary layer thickness. Hot-wire measurements reveal that above the diverging region, the local mean velocity increases while the turbulent intensity decreases, resulting in a thinner overall boundary layer thickness in these locations. The opposite situation occurs over the converging region, where the local mean velocity is decreased and the turbulent intensity increases, producing a locally thicker boundary layer. Increasing the converging–diverging angle or the viscous-scaled riblet height results in stronger spanwise perturbations. For the strongest convergent–divergent angle, the spanwise variation of the boundary layer thickness between the diverging and converging region is almost a factor of two. Such a large variation is remarkable considering that the riblet height is only 1% of the unperturbed boundary layer thickness. Increasing the fetch seems to cause the perturbations to grow further from the surface, while the overall strength of the induced high and low speed regions remain relatively unaltered. Further analysis of the pre-multiplied energy spectra suggests that the surface roughness has modified or redistributed the largest scale energetic structures.     

Numerical and experimental investigation of the laminar boundary layer over riblets

One of the main aims of this work is to show to what extent drag reduction in a turbulent boundary layer can be ascribed to a purely viscous effect. A numerical and experimental study is performed in a laminar boundary layer over triangular riblets. The 2-D parabolic equations of motion are integrated using an x marching method and the discretised system is solved with the MSI algorithm. The influence of the riblet geometrical parameters and of the number of grid points is studied. Measurements are carried out in a water tunnel with forward scatter and backscatter laser-Doppler velocimetry extending within the riblets. The longitudinal velocity component measurements and computations are practically identical. Numerical results presented herein show that a slight drag reduction is obtained for s/h=1.2. It appears that, as far as friction is concerned, the wetted area is not the surface to be considered. Thus, the boundary layer over riblets would behave like a boundary layer on an equivalent smooth plate located beneath the crest plane. The numerical study in terms of the riblet height h shows best results are for h tending to zero, with the ratio s/h being equal to 1.2.     

Drag reduction in riblet-lined pipes

The possibilities of reducing the drag in pipes with a circular cross section by lining them with riblets have been investigated experimentally for developed turbulent air flow. The maximum drag reduction of 6–7% in the riblet-lined as compared with the smooth pipe was obtained for a dimensionless riblet pitch, expressed in law-of-the-wall parameters,s ⁺=14–18.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 1, pp. 57–61, January–February, 1995.     

Parametric Study on a Sinusoidal Riblet for Drag Reduction by Direct Numerical Simulation

The direct numerical simulation of fully developed turbulent channel flow with a sinusoidal riblet surface has been carried out at the friction Reynolds number of 110. Lateral spacing of adjacent walls in a sinusoidal riblet is varied sinusoidally in the streamwise direction. The average lateral spacing of a sinusoidal riblet is larger than the diameter of a quasi-streamwise vortex and its wetted area is smaller than that of ordinary straight-type riblets. We investigate the effect of sinusoidal riblet design parameters on the drag reduction rate and flow statistics in this paper. The parametric study shows that the maximum total drag reduction rate is approximately 9.8% at a friction Reynolds number of 110. The riblet induces downward and upward flows in the expanded and contracted regions, respectively, which contribute to periodic Reynolds shear stress. However, the random Reynolds shear stress decreases drastically as compared with the flat surface case, resulting in the reduction of total drag owing to the sinusoidal riblet. We also performed vortex tracking to discuss the motion of the vortical structure traveling over the sinusoidal riblet surface. Vortex tracking and probability analysis for the core of the vortical structure show that the vortical structure is attenuated owing to the sinusoidal riblet and follows the characteristic flow. These results show that the high skin-friction region on the channel wall is localized at the expanded region of the riblet walls. In consequence, the wetted area of the riblet decreases, resulting in the drag-reduction effect.     

Riblet flow calculation with a low Reynolds number κ - ε model

A low Reynolds number κ - ε model has been used to calculate the turbulent boundary layer over riblets. Calculated mean velocity, Reynolds shear stress and kinetic energy distributions are generally in good agreement with available experimental data. The comparison between these distributions and those in a corner flow points to a significant difference between the two flows and the unlikelihood of counter-rotating vortices within the riblet grooves. One shortcoming of the present κ - ε model is the relatively slow return to a two-dimensional turbulence state as the distance from the riblet surface increases.     

A numerical study of riblet effects on laminar flow through a plane channel

Numerical computations are reported of fully-developed flow through plane channels with knife-edge riblets. The study has covered riblet height: spacing ratios from 0.5 to 3 and riblet heights ranging from 0.1%–4.0% of the distance between the channel walls. In no case did results indicate a reduction in drag compared with the case of a smooth channel, a result that is in contrast with earlier studies. It is suggested that apparent drag reductions reported earlier in laminar flow may have arisen from the use of an insufficiently fine grid.     

Rotating cylinder drag balance with application to riblets

Experimental results are reported and discussed for a rotating cylinder drag balance designed to predict drag reduction by surfaces like riblets. The apparatus functions by measuring the torque applied to the inner cylinder by a fluid, such as water, that is set in motion by the controlled rotation of the outer cylinder. The instrument was validated by calibration for laminar flow and comparison of turbulent flow results to the those of G. I. Taylor. The ability to predict drag reduction was demonstrated by testing 114 m symmetric sawtooth riblets, which gave a maximum reduction of about 5% and an overall drag reduction range of 5<S ⁺<20, both of which are in excellent comparison to results reported in literature. The most suitable conditions for testing riblets are to apply the riblets only to the inner cylinder surface and to use cylinders for which the curvature of the flow is minimized. Received: 2 February 1999/Accepted: 1 October 1999     

Effect of longitudinal riblets on the aerodynamic characteristics of a straight wing

The results of balance aerodynamic tests on model straight wings with smooth and ribbed surfaces at an angle of attack =–4°–12°, Mach number M=0.15–0.63, and Reynolds number Re=2.4·10⁶–3.5·10⁶ are discussed. The nondimensional riblet spacings ⁺, which determines the effect of the riblets on the turbulent friction drag, and the effect of riblets on the upper and/or lower surface of a straight wing on its drag, lift, and moment characteristics are estimated.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 2, pp. 33–38, March–April, 1995.