Drag characteristics of longitudinal and transverse riblets at low dimensionless spacings

A surface grooved with microscopic riblets aligned parallel to the flow is an effective means to reduce the turbulent skin friction up to 10% compared to a smooth surface. The maximum drag reduction is found for a dimensionless rib spacing s ⁺ in the range of 15–17. For s ⁺ < 10, a linear behaviour of the drag reduction curve is predicted by viscous theory. This linear slope of the drag reduction curve is in contradiction to Schlichting’s postulation of a hydraulically smooth behaviour of small-scale roughness in a turbulent flow. This regime of evanescent dimensionless rib spacings is investigated experimentally by direct wall shear stress measurements in a fully developed channel flow. Additionally, a numerical calculation of the viscous flow over riblets was carried out to predict the drag reducing behaviour. The experimental results show a linear drag reducing behaviour down to s ⁺ = 0.3, which is in good agreement with the numerical results of the viscous simulation. The postulation of Schlichting’s hydraulically smooth regime of a rough surface was not confirmed, neither for a riblet surface nor for a surface geometry with grooves oriented perpendicular to the flow. In the latter case, the drag increases as a quadratic function of the roughness height.     

Drag measurements on V-grooved surfaces on a body of revolution in axial flow

In water flows with velocities of up to 9 m/s the friction drag of a body of revolution in axial flow was investigated for dependence on the body surface structure. This was done for different types of riblet film fixed on the surface with the riblet direction aligned with the flow. The lateral spacing between the triangular shaped riblets varied between 0.033 mm and 0.152 mm. In all cases the riblet spacing was equal to the riblet height. For comparison a smooth reference film was used.Depending on the Reynolds number and the non-dimensional riblet spacings ⁺, a turbulent drag reduction of up to 9% could be achieved with riblets in comparison with the flow over a smooth surface.In the region of transition to turbulent flow and with non-dimensional riblet spacings ofs ⁺10–15 drag reductions of up to 13% were obtained. It is therefore conjectured, that in addition to hampering the near wall momentum exchange, the riblets can delay the development of initial turbulent structures in time and space.     

Tests of drag-reducing polymer coated on a riblet surface

Experiments have been carried out at BMT where the drag reduction due to Hoechst U-groove riblets, a polymer coating, and the two combined were measured in a towing tank on a one-third scale model of the America's Cup winning yacht, Australia II. The results indicated that the riblet/polymer combination offered an overall improvement in drag reduction characteristics over either riblets or polymer coating alone, with a maximum reduction of 3.5% observed for a non-dimensional S ⁺=8. The qualitative behaviour of the drag reduction was similar to that recorded in earlier pipe flow experiments, employing an injection of polymer additive and 3M V-groove riblets, but contrary to that recorded in studies of an axisymmetric body, also coated with 3M riblets, in a drop tank filled with a polymer solution.     

Drag Reduction of a Circular Cylinder Using an Upstream Rod

Experimental studies on the drag reduction of the circular cylinder were conducted by pressure measurement at a Reynolds number of 82 000 (based on the cylinder diameter). A rod was placed upstream of and parallel to the cylinder to control the flow around the cylinder. The upstream rod can reduce the resultant force of the cylinder at various spacing between the rod and the cylinder for α < 5^∘(α defined as the staggered angle of the rod and the cylinder). For α > 10^∘, the resultant force coefficient has a large value, so the upstream rod cannot reduce the force on the cylinder any more. For α = 0^∘ and d/D = 0.5 (where d and D are the diameter of the rod and the cylinder, respectively), the maximum drag of the cylinder reduces to 2.34% that of the single cylinder. The mechanism of the drag reduction of the cylinder with an upstream rod in tandem was presented by estimating the local contributions to the drag reduction of the pressure variation. In the staggered arrangement, the flow structures have five flow patterns (they are the cavity mode, the wake splitting mode, the wake merge mode, the weak boundary layer interaction mode and the negligible interaction mode) according to the pressure distribution and the hydrogen bubble flow visualization. The half plane upwind of the cylinder can be divided to four regions, from which one can easily estimates the force acting on the circular cylinder with an upstream rod in staggered arrangement.     

A comparison of the drag-reducing benefits of riblets in internal and external flows

Equivalent drag-reducing performance is observed with 3 M riblets in fully developed internal (pipe) and developing external (flat plate) flows. Drag reduction begins around h ⁺ = 3, peaks between 6 and 9% at about h ⁺ = 12, and becomes zero for a value of h ⁺ between 20 and 30. In laminar pipe flow no significant change in drag is observed with the 3 M riblets present. At high Reynolds numbers, after exhibiting fully rough behaviour, friction factors for the 3 M riblets are observed to monotonically decrease with increasing Reynolds number.     

Flow field analysis of a turbulent boundary layer over a riblet surface

The near-wall flow structures of a turbulent boundary layer over a riblet surface with semi-circular grooves were investigated experimentally for the cases of drag decreasing (s ⁺=25.2) and drag increasing (s ⁺=40.6). One thousand instantaneous velocity fields over riblets were measured using the velocity field measurement technique and compared with those above a smooth flat plate. The field of view was 6.75 × 6.75 mm² in physical dimension, containing two grooves. Those instantaneous velocity fields were ensemble averaged to get turbulent statistics including turbulent intensities and turbulent kinetic energy. To see the global flow structure qualitatively, flow visualization was also carried out using the synchronized smoke-wire technique under the same experimental conditions. For the case of drag decreasing (s ⁺=25.2), most of the streamwise vortices stay above the riblets, interacting with the riblet tips frequently. The riblet tips impede the spanwise movement of the streamwise vortices and induce secondary vortices. The normalized rms velocity fluctuations and turbulent kinetic energy are small near the riblet surface, compared with those over a smooth flat plate. Inside the riblet valleys, these are sufficiently small that the increased wetted surface area of the riblets can be compensated. In addition, in the outer region (y ⁺ > 30), these values are almost equal to or slightly smaller than those for the smooth plate. For the case of drag increasing (s ⁺=40.6), however, most of the streamwise vortices stay inside the riblet valleys and contact directly with the riblet surface. The high-speed down-wash flow penetrating into the riblet valley interacts actively with the wetted riblet surface and increases the skin friction. The rms velocity fluctuations and turbulent kinetic energy have larger values compared with those over a smooth flat plate. Received: 24 March 1999/Accepted: 10 March 2000     

Drag reduction using surfactants in a rotating cylinder geometry

Turbulent Couette flow between two circular cylinders has been used for drag reduction experiments using surfactants. In the experiments presented here, only the outer cylinder rotates, the inner cylinder remains at rest and accurate measurements of the torque at the inner cylinder are measured. Water is used as a reference fluid. A drag reducing surfactant called Arquad S-50 (Akzo Nobel Surface Chemistry LLC, Chicago, Ill., USA) (5 mM)+NaSal (12.5 mM) was used as the drag reduction agent. This surfactant can reduce the drag up to 70% (a Reynolds number of about 70,000–150,000) as measured by pressure drop in a pipe flow. Experiments in Couette flow also show drag reduction in the turbulent range. Two arrangements were used, (1) one small trip-wire on the inner cylinder, and (2) four larger trip-wires on the outer cylinder. These trips reduce the critical Reynolds number for transition from laminar to turbulent flow. In case (1), we obtained 18% drag reduction at 5,000<Re<15,000 and in case (2), we obtained an average reduction of about 20% at 2,000<Re<10,000, increasing up to 30% at Re=15,000. The paper also discusses two important problems. First, the shear rate is not constant in the radial gap in circular Couette flow. For non-Newtonian fluids, where the molecular viscosity is a function of the shear rate, this effect must be considered. Second, which viscosity should be used in the Reynolds number? For pipe flow measurements, most authors use the viscosity of the solvent (generally water and Newtonian). For measurements in the Couette flow, we use a different approach, which is described in this paper. We conclude that Couette flow is a useful method for drag reduction investigations. Its advantage is the much smaller geometry in comparison to those of conventional test facilities such as wind tunnels, water, or oil channels or in tubes.     

The reduction of skin friction by riblets under the influence of an adverse pressure gradient

In this paper we address the effectiveness of riblets on skin friction reduction under the influence of an adverse pressure gradient. The measurements were taken in a wind tunnel. Skin friction was observed with a drag balance which has a reproducibility of better than 1%. The accuracy of the balance is estimated to be less than 1% for the case of zero-pressure gradient and at most 3% for a pressure gradient. The data on skin friction reduction at zero pressure gradient were consistent with previous results and amount to 5% at dimensionless riblet width of s ⁺ = 13. We find that at all adverse pressure gradients the skin friction reduction by riblets persists. At moderate pressure gradients the reduction increases somewhat to 7%. The velocity profile which is also measured, exhibits the characteristic shape for a boundary layer with an adverse pressure gradient and agrees well with theory. From the velocity profiles measured at two stations we estimated with the help of a momentum balance the skin friction and skin friction reduction. The results differ from the drag-balance data. Due to the poor accuracy of the momentum balance method which we estimate in our case, we conclude that the results obtained with this method are less reliable than those obtained with the drag balance. This throws some doubt on previous results on drag reduction under the influence of a pressure gradient which were based on the momentum balance method.     

Drag reduction by polymer solutions in a riblet-lined pipe

The flow of 3 to 100 wppm aqueous solutions of a polyethyleneoxide polymer,M _w=6.2×;10⁶, was studied in a 10.2 mm i.d. pipe lined with 0.15 mm V-groove riblets, at diametral Reynolds numbers from 300 to 150000. Measurements in the riblet pipe were accompanied by simultaneous measurements in a smooth pipe of the same diameter placed in tandem. The chosen conditions provided turbulent drag reductions from zero to the asymptotic maximum possible. The onset of polymer-induced drag reduction in the riblet pipe occurred at the same wall shear stress, * _w =0.65 N/m², as that in the smooth pipe. After onset, the polymer solutions in the riblet pipe initially exhibited linear segments on Prandtl-Karman coordinates, akin to those seen in the smooth pipe, with specific slope increment . The maximum drag reduction observed in the riblet pipe was independent of polymer concentration and well below the asymptotic maximum drag reduction observed in the smooth pipe. Polymer solution flows in the riblet pipe exhibited three regimes: (i) Hydraulically smooth, in which riblets induced no drag reduction, amid varying, and considerable, polymer-induced drag reduction; this regime extended to non-dimensional riblet heightsh ⁺<5 in solvent andh ⁺<10 in polymer solutions. (ii) Riblet drag reduction, in which riblet-induced flow enhancementR>0; this regime extended from 5<h ⁺<22 in solvent and from 10<h ⁺<30 in the 3 wppm polymer solution, with respective maximaR=0.6 ath ⁺=14 andR=1.6 ath ⁺=21. Riblet drag reduction decreased with increasing polymer concentration and increasing polymer-induced flow enhancement S. (iii) Riblet drag enhancement, whereinR<0; this regime extended for 22<h ⁺<110 in solvent, withR;–2 forh ⁺>70, and was observed in all polymer solutions at highh ⁺, the more so as polymer-induced drag reduction increased, withR<0 for allS>8. The greatest drag enhancement in polymer solutions,R=–7±1 ath ⁺=55 whereS=20, considerably exceeded that in solvent. Three-dimensional representations of riblet- and polymer-induced drag reductions versus turbulent flow parameters revealed a hitherto unknown dome region, 8<h ⁺<31, 0<S<10, 0<R<1.5, containing a broad maximum at (h ⁺,S,R) = (18, 5, 1.5). The existence of a dome was physically interpreted to suggest that riblets and polymers reduce drag by separate mechanisms.     

Drag reduction in riblet-lined pipes

The possibilities of reducing the drag in pipes with a circular cross section by lining them with riblets have been investigated experimentally for developed turbulent air flow. The maximum drag reduction of 6–7% in the riblet-lined as compared with the smooth pipe was obtained for a dimensionless riblet pitch, expressed in law-of-the-wall parameters,s ⁺=14–18.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 1, pp. 57–61, January–February, 1995.     

沟槽面湍流边界层结构实验研究

应用激光测速技术和氢气泡流动显示技术对沟槽面湍流边界层特性及近壁区拟序结构特征进行了精细的测量和观察。实验结果表明：与光滑面湍流边界层相比,沟槽面端流边界层的黏性底层厚度、过渡层厚度及流速分布对数公式中的积分常数C均有所增大,说明采用的沟槽面具有减阻特性。此外,无量纲低速带条间距明显减小,最多减小20%,说明无量钢低速带条平均间距的缩短与湍流减阻密切联系。     

On near-wall turbulence-generating events in a turbulent boundary layer on a riblet surface

The boundary layer over a drag reducing riblet surface is investigated using hot-wire anemometry and flow visualisation. The concept of a riblet sublayer is introduced, and a definition is proposed in terms of a region of reduced turbulence energy production formed near the wall by the addition of riblets. The hot wire records are examined using a modified form of quadrant analysis, and results obtained over plain and riblet surfaces are compared. Close to the wall, the addition of riblets produces a marked reduction in the occurrence of ejection (2nd quadrant) events. A corresponding increase in the incidence of sweep (4th quadrant) events is accompanied by the development of a strong tendency toward a preferred event duration, and a preferred interval between events. These changes diminish rapidly with distance from the surface, becoming almost undetectable beyondy ⁺=40. They are discussed in the light of flow visualisation results, and interpreted in terms of mechanisms associated with the interaction between the riblets and the inner boundary layer flow structures. A conceptual model of the flow mechanisms in the riblet sublayer is proposed.     

Parallel spectral-element—Fourier simulation of turbulent flow over riblet-mounted surfaces

The flow in a channel with its lower wall mounted with streamwise V-shaped riblets is simulated using a highly efficient spectral-element—Fourier method. The range of Reynolds numbers investigated is 500 to 4000, which corresponds to laminar, transitional, and turbulent flow states. Our results suggest that in the laminar regime there is no drag reduction, while in the transitional and turbulent regimes drag reduction up to 10% exists for the riblet-mounted wall in comparison with the smooth wall of the channel. For the first time, we present detailed turbulent statistics in a complex geometry. These results are in good agreement with available experimental data and provide a quantitative picture of the drag-reduction mechanism of the riblets.This work was supported by National Science Foundation Grants CTS-8906432, CTS-8906911, and CTS-8914422, AFOSR Grant No. AFOSR-90-0124, and DARPA Grant No. N00014-86-K-0759. The computations were performed on the Cray Y/MP's of NAS at NASA Ames and the Pittsburgh Supercomputing Center, and on the Intel 32-node iPSC/860 hypercube at Princeton University.     

A numerical study of riblet effects on laminar flow through a plane channel

Numerical computations are reported of fully-developed flow through plane channels with knife-edge riblets. The study has covered riblet height: spacing ratios from 0.5 to 3 and riblet heights ranging from 0.1%–4.0% of the distance between the channel walls. In no case did results indicate a reduction in drag compared with the case of a smooth channel, a result that is in contrast with earlier studies. It is suggested that apparent drag reductions reported earlier in laminar flow may have arisen from the use of an insufficiently fine grid.     

On the relationship between drag and vertical velocity fluctuations in flow over riblets and liquid infused surfaces

Direct numerical simulations (DNS) of flow over triangular and rectangular riblets in a wide range of size and Reynolds number have been carried out. The flow within the grooves is directly resolved by exploiting the immersed-boundary method. It is found that the drag reduction property is primarily associated with the capability of inhibiting vertical velocity fluctuations at the plane of the crests, as in liquid-infused surfaces (LIS) devices. This is mimicked in DNS through artificial suppression of the vertical velocity component, which yields large drag decrease, proportionate to the riblets size. A parametrization of the drag reduction effect in terms of the vertical velocity variance is found to be quite successful in accounting for variation of the controlling parameters. A Moody-like friction diagram is thus introduced which incorporates the effect of slip velocity and a single, geometry-dependent parameter. Reduced drag-reduction efficiency of LIS-like riblets is found as compared to cases with artificially imposed slip velocity. Last, we find that simple wall models of riblets and LIS-like devices are unlikely to provide accurate prediction of the flow phenomenon, and direct resolution of flow within the grooves in necessary.     

Riblet drag reduction in mild adverse pressure gradients: A numerical investigation

Riblet films are a passive method of turbulent boundary layer control that can reduce viscous drag. They have been studied with great detail for over 30 years. Although common riblet applications include flows with Adverse Pressure Gradients (APG), nearly all research thus far has been performed in channel flows. Recent research has provided motivation to study riblets in more complicated turbulent flows with claims that riblet drag reduction can double in mild APG common to airfoils at moderate angles of attack. Therefore, in this study, we compare drag reduction by scalloped riblet films between riblets in a zero pressure gradient and those in a mild APG using high-resolution large eddy simulations. In order to gain a fundamental understanding of the relationship between drag reduction and pressure gradient, we simulated several different riblet sizes that encompassed a broad range of s⁺ (riblet width in wall units), similarly to many previously published experimental studies. We found that there was only a slight improvement in drag reduction for riblets in the mild APG. We also observed that peak values of streamwise turbulence intensity, turbulent kinetic energy, and streamwise vorticity scale with riblet width. Primary Reynolds shear stresses and turbulence kinetic energy production however scale with the ability of the riblet to reduce skin-friction.     

Aerodynamic characteristics of a square cylinder with a rod in a staggered arrangement

The aerodynamic characteristics of a square cylinder with an upstream rod in a staggered arrangement were examined. The pressure measurement was conducted in a wind tunnel at a Reynolds number of Re_D=82,000 (based on the width of the square cylinder) and the flow visualization was carried out in a water tunnel with the hydrogen bubble technique at Re_D=5,200. When the rod and the square cylinder were in tandem, the reduction of drag was mainly caused by the increase of the rear suction pressure. When the staggered angle was introduced, the shield and disturbance effect of the rod on the square cylinder diminished, which results in the increase of the cylinder drag. The side force induced by the staggered angle is small (the maximum value is 20% of the drag of the isolate square cylinder). There were six different flow modes with various staggered angles and spacing ratios, and the corresponding flow patterns are presented in present paper.     

Prediction of unsteady,separated boundary layer over a blunt body for laminar,turbulent, and transitional flow

The focus of this paper is to study the ability of unsteady RANS‐based CFD to predict separation over a blunt body for a wide range of Reynolds numbers particularly the ability to capture laminar‐to‐turbulent transition. A perfect test case to demonstrate this point is the cylinder‐in‐crossflow for which a comparison between experimental results from the open literature and a series of unsteady simulations is made. Reynolds number based on cylinder diameter is varied from 10⁴ to 10⁷ (subcritical through supercritical flow). Two methods are used to account for the turbulence in the simulations: currently available eddy–viscosity models, including standard and realizable forms of the k–ε model; and a newly developed eddy–viscosity model capable of resolving boundary layer transition, which is absolutely necessary for the type and range of flow under consideration. The new model does not require user input or ‘empirical’ fixes to force transition. For the first time in the open literature, three distinct flow regimes and the drag crisis due to the downstream shift of the separation point are predicted using an eddy–viscosity based model with transition effects. Discrepancies between experimental and computational results are discussed, and difficulties for CFD prediction are highlighted. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical and experimental investigation of the laminar boundary layer over riblets

One of the main aims of this work is to show to what extent drag reduction in a turbulent boundary layer can be ascribed to a purely viscous effect. A numerical and experimental study is performed in a laminar boundary layer over triangular riblets. The 2-D parabolic equations of motion are integrated using an x marching method and the discretised system is solved with the MSI algorithm. The influence of the riblet geometrical parameters and of the number of grid points is studied. Measurements are carried out in a water tunnel with forward scatter and backscatter laser-Doppler velocimetry extending within the riblets. The longitudinal velocity component measurements and computations are practically identical. Numerical results presented herein show that a slight drag reduction is obtained for s/h=1.2. It appears that, as far as friction is concerned, the wetted area is not the surface to be considered. Thus, the boundary layer over riblets would behave like a boundary layer on an equivalent smooth plate located beneath the crest plane. The numerical study in terms of the riblet height h shows best results are for h tending to zero, with the ratio s/h being equal to 1.2.     

FLOW STRUCTURE IN THE TURBULENT BOUNDARY LAYER OVER DIRECTIONAL RIBLETS SURFACES

本文采用时间解析的二维粒子图像测速技术,对零压力梯度光滑以及汇聚和发散沟槽表面平板湍流边界层统计特性和流动结构进行了研究.结果表明在垂直于汇聚和发散沟槽表面的对称平面内,相对于光滑壁面,发散沟槽壁面使当地边界层厚度、壁面摩擦阻力、湍流脉动、雷诺应力等明显减小;而汇聚沟槽壁面对湍流边界层特性和流动结构的影响正好相反,汇聚沟槽使壁面流体有远离壁面向上运动的趋势,因而导致边界层厚度增加了约43%;同时,在汇聚沟槽表面情况下流向大尺度相干结构更容易形成,这对减阻是不利的.此外,顺向涡数量在湍流边界层的对数区均存在一个极大值,发散沟槽表面所对应的极大值位置更靠近沟槽壁面,而在汇聚沟槽表面则有远离壁面的趋势,由顺向涡诱导产生的较强的喷射和扫掠运动会在湍流边界层中产生较强的剪切作用,顺向涡数量的减少是发散沟槽壁面当地摩擦阻力降低的主要原因.