基于非线性梁理论的有限质点法

有限质点法是以向量式力学为基础,用有限数量的质点来模拟结构的变形行为,质点的运动由牛顿运动定律来计算。在有限质点法中,质点通过构件相连,构件约束着质点的运动,并且其内力由质点的运动变量来描述。基于向量式力学的基本思想和非线性梁理论,提出了一种新的有限质点法,该方法在共旋单元坐标系中描述梁的非线性变形。以空间梁系结构为例,推导了计算构件内力的非线性公式,并考虑了弯扭耦合变形。通过两个连续欧拉角的变换公式得到共旋坐标系的旋转矩阵。与传统的有限质点法相比,本文提出的方法避免了刚体虚转动分析。通过四个结构的数值求解,验证了本文方法在计算结构大变形响应时具有较高的精度。     

圆中空夹层钢管混凝土压扭构件试验研究

以轴压比和长细比为主要参数设计了7根圆中空夹层钢管混凝土试件,为了便于对比分析,同时设计了2根圆实心钢管混凝土试件,对其在压扭复合受力状态下的力学性能进行了试验研究。对试验现象和试验结果进行了描述与分析,结果表明:圆中空夹层钢管混凝土压扭构件的扭矩-转角全过程曲线未出现下降段,试件表现出一定的后期承载潜力,具有较好的塑性和延性性能;钢管对混凝土的约束效应在加载后期更为显著;轴压比、长细比和空心率对压扭试件的初始刚度影响不大,但轴压比和长细比对试件的抗扭承载力有一定影响。最后,采用压扭构件承载力相关方程对圆中空夹层钢管混凝土压扭构件的抗扭承载力进行了计算,计算结果与试验结果基本接近且总体偏于安全,可为工程设计提供参考。     

一个高周疲劳损伤演化修正模型

将连续损伤力学应用到疲劳问题中, 得到合理的疲劳损伤演化方程,被认为是预测疲劳寿命最有效的方法之一. 在研究Lemaitre最新疲劳损伤演化方程基础上, 根据试验数据提出了一个修正的高周疲劳损伤演化方程, 该方程可以考虑应力幅、平均应力等影响因素. 以2A12-T4铝合金为例, 得到了修正模型的材料常数. 将该修正模型以UMAT子程序形式嵌入ABAQUS主程序, 计算了两种构件14种不同受载情况下的疲劳寿命, 所得计算寿命与试验结果误差均值约15%, 说明修正的疲劳损伤演化方程可以很好地计算金属构件的高周疲劳寿命.      

复合受力下焊接栓钉SRC柱抗扭承载力计算

为研究压、弯、剪、扭复合受力下焊接栓钉型钢混凝土(SRC)柱的抗扭承载力计算方法,基于滞回性能试验结果,分析了试验过程和破坏形态,利用了空间桁架理论与叠加原理,提出了复合受力下焊接栓钉SRC柱抗扭计算模型和强度统一方程。结果表明:所提出的强度统一方程和抗扭承载力计算方法的计算结果与试验结果均值误差均在3%内,吻合较好。     

发动机叶片扭转和弯曲变形同步测量新方法

扭转和弯曲变形测量可以确定叶片弯扭变形耦合的特征,为叶片弯扭耦合分析提供可用的试验手段。本文提出了一种发动机叶片扭转和弯曲变形同步测量的新方法,其中,扭转角度测量方法能更加灵活地应用于测量叶片类形状不规则构件的扭转变形,而弯曲变形测量方法解决了叶片变形方向未知且存在弯扭耦合时的叶片变形测量问题,从而可实现对叶片截面扭转和弯曲变形的同步测量。对上述测量方法进行了专门的验证试验,结果表明:与传统方法测量结果相比,扭转角度测量偏差小于1%,挠度测量偏差小于2%,满足工程测量精度要求。     

一种钢管混凝土格构柱极限承载力的快速计算方法

采用半波正弦曲线模拟杆件的变形曲线,在考虑紧箍效应钢管混凝土应力-应变关系和剪切变形影响的基础上,建立了杆件中截面的平衡方程,提出了钢管混凝土格构柱弹塑性极限承载力数值方法,并编制了相应的计算程序。该方法不仅适用于两端偏心相等的偏压构件及两端偏心不等的偏压构件的弹塑性极限承载力的计算,而且,其收敛速度很快,比分段合成数值法更能适用于工程计算。利用提出的计算方法和编制的程序对国内已有两端偏心相同的四肢钢管混凝土格构偏压长柱的试验结果进行了计算,并与现有规程及分段合成法进行了比较,结果表明:规程计算方法结果偏于保守,计算误差大,本文方法的计算结果与试验结果吻合良好。     

饱和砂土中泥浆渗透的变形-渗流-扩散耦合计算模型

传统的泥浆渗透计算中没有考虑土体变形和浆液流速的影响.根据泥浆颗粒的质量守恒定律推导了耦合流速的浓度扩散方程,并通过在浓度方程中引入沉积系数进一步计算得到沉积颗粒的质量;同时,以沉积量作为耦合项对毕奥固结方程中的水量连续方程进行了修正,在此基础上建立了变形-渗流-扩散耦合的控制方程及其变分原理. 采用有限单元法求解基本方程,运用了时间增量法与直接迭代法,并利用一维试验验证计算方法的可靠性,并与赫齐格的经典模型的计算结果进行了比较,结果表明,本文建立的模型的计算结果可以较好地预测各组试验中颗粒的沉积规律,且吻合程度优于仅考虑颗粒对流和扩散的传统计算方法. 最后,将泥浆在槽壁中的渗透简化为二维问题并进行了计算,计算结果与工程认识相符合,泥浆的沉积填充效应随深度的增加而增大,施工时需要严格控制浅层作业段的机械垂直度;成槽机的下斗抓挖时机可以根据地层填充的致密程度进行计算,对现场施工具有一定的指导意义.      

配筋钢纤维混凝土纯扭构件荷载—变形全过程“两阶段”分析法

本文将配筋钢纤维混凝土纯扭构件的荷载－变形全过程分成形裂前和开裂后两阶段，开裂前按弹性工作状态计算；开裂后采用空间软化桁架模型分析，比较表明，理论计算与试验结果符合较好。     

DNA纳米管的扭转刚度模型

刚度是衡量材料弹性变形难易程度的一个定量表征参数,与DNA纳米管静动力学特性及其结构生物功能密切相关．本文致力于研究DNA纳米管的扭转刚度．首先,在六角形均匀封装条件下,考虑到单个DNA杆件弯扭组合问题的静不定特点,我们利用平衡方程、变形协调方程和弹性本构方程,合理预测了DNA纳米管扭转实验中单个DNA杆件的弯扭组合变形,由此给出了DNA纳米管扭转刚度预测的解析模型．最后的结果表明：随着DNA杆数的增加,DNA纳米管的弯曲刚度显著增加,而其扭转刚度却几乎不变,合理解释了扭转实验中发现的现象．有关结论为DNA折叠结构的设计和应用提供了参考．     

油水两相分层流界面波变形及破坏力学特性研究

油水两相流在管内从分层流到分散流流动状态的改变主要由界面波形态改变引起,但目前具体转变机理仍未知,为此,本文结合振幅稳定性给出油水两相分层流界面波的正弦波模型,从受力平衡的角度出发,提出界面波所受力的计算模型,得到其变形及破坏的临界预测方程,根据预测方程即可判断界面波状态,并通过数值拟合发现油水界面波的变形与管道倾角及...     

扇形截面杆扭转问题的差分线法

导出了扇形截面杆扭转问题偏微分方程的差分线法常微分方程组, 并解析求解了该方程组, 得到了扭转应力函数的半解析解, 计算了扭转应力及扭转刚度. 计算过程中, 用追赶法计算 常微分方程组的特解, 用公式计算三对角矩阵的特征值与特征向量, 利用实对阵矩阵的特征 向量相互正交的特性避免矩阵求逆计算, 利用复化梯形公式计算扭转刚度. 整个求解过程在 角度方向离散微分方程和用复化梯形公式进行面积积分时引入了误差, 其他求解过程是精确 的. 计算结果与已有结果进行了对比, 显示了算法的正确性. 该算法对工程中扇形截面扭 转杆的设计有一定的实用价值.     

薄壁杆侧向稳定分析有限杆元模型

根据位移变分原理,建立有限杆元模型,对薄壁杆进行侧向稳定分析。在考虑截面扭转、翘曲同时,特别考虑了反映剪力滞后现象的杆壁中面上剪应交的影响。推导出薄壁杆侧向屈曲能量方程可适用求解常用边界条件,任意棱形截面形状的薄壁杆的屈曲特征值问题。     

Variational formulation of stability problems for thin-walled members

Summary The governing equations for thin-walled members subjected to axial force, biaxial bending and torsion are formulated by variational method. The resulting equations differ slightly with currently accepted governing equations. Numerical examples are solved for simple problems to illustrate some of the features of the proposed equations.

---

Übersicht Die beschreibenden Differentialgleichungen für dünnwandige Bauglieder, die durch achsiale Kräfte, biachsiale Biegung und Torsion beansprucht sind, werden nach einem Variationsverfahren aufgestellt. Die so erhaltenen Gleichungen unterscheiden sich etwas von den zur Zeit üblichen Gleichungen. Um die Eigenschaften der jetzt vorgeschlagenen Gleichungen zu zeigen, werden numerische Ergebnisse für einige einfache Aufgaben angegeben.

---

---

On leave from University of Tokyo, Tokyo Japan.     

The solution of integral equations with strongly singular kernels applied to the torsion of cracked circular cylinder

In this paper,the functions of warping displacement interruption defined on the crack lines are taken for the fundamental unknown functions.The torsion problem of cracked circular cylinder is reduced to solving a system of integral equations with strongly singular kernels.Using the numerical method of these equations,the torsional rigidities and the stress intensity factors are calculated to solve the torsion problem of circular cylinder with star-type and other different types of cracks.The numerical results are satisfactory.     

Evaluation of multiaxial theories for room-temperature plasticity and elevated-temperature creep and relaxation of several metals

Based on the assumption that the material satisfies the condition of isotropic hardening for either a von Mises or a Tresca material, finite-strain theories are derived for solid circular torsion members for the conditions that the inelastic deformations are either time independent or time dependent. In the latter case, both creep and relaxation theories are derived. At room temperature the theories are evaluated for each of eight metals using finite-strain data from tension, compression and torsion members. Of the six metals that are found to satisfy the condition required for the isotropic-hardening model, two are von Mises, one is Tresca, and the other three are between von Mises and Tresca. At elevated temperatures, the theories are evaluated for each of five of the latter six metals, using data from tension and torsion members. Material properties obtained from the tension specimens are used to predict creep and relaxation curves for the torsion members. Contrary to the results at room temperature, creep curves for the torsion members do not all fall within the region bounded by von Mises and Tresca theories. In the case of relaxation, either excellent agreement is obtained between the von Mises strain-hardening theory and experimental data or the theory is conservative.     

Stochastic response of an axially loaded composite Timoshenko beam exhibiting bending–torsion coupling

A spectral finite element method is proposed to investigate the stochastic response of an axially loaded composite Timoshenko beam with solid or thin-walled closed section exhibiting bending–torsion materially coupling under the stochastic excitations with stationary and ergodic properties. The effects of axial force, shear deformation (SD) and rotary inertia (RI) as well as bending–torsion coupling are considered in the present study. First, the damped general governing differential equations of motion of an axially loaded composite Timoshenko beam are derived. Then, the spectral finite element formulation is developed in the frequency domain using the dynamic shape functions based on the exact solutions of the governing equations in undamped free vibration, which is used to compute the mean square displacement response of axially loaded composite Timoshenko beams. Finally, the proposed method is illustrated by its application to a specific example to investigate the effects of bending–torsion coupling, axial force, SD and RI on the stochastic response of the composite beam.     

含有裂纹和夹杂的复合柱体的扭转

本文根据Saint-Venant扭转理论,提出了一种能用于扭转分析的线夹杂模型,并得到了它的基本解,进而将此解与的单层势函数解及单裂纹基本解结合,对同时带有裂纹和夹杂的复合柱体的扭转作了讨论,最后将问题归为解一组混合型积分方程,并建议了数值解法。文中通过问题的退化,证明本文提出的夹杂模型在数学和力学上都是正确的,最后作了若干数值例子的计算,其结果令人满意。     

Fracture analysis for torsion problems of a composite cylinder with curvilinear cracks

The Salnt-Venant torsion problems of a composite cylinder with curvilinear cracks were investigated. By considering the bimaterial interface as a boundary of the outer bar or inner one, the problem was reduced to the solution of boundary integral equations on the crack, external boundary and interface. Using the new boundary element method, some typical torsion problems of a composite cylinder involving a straight or kinked crack were calculated. The obtained results were compared with data in the literature to show validity and applicability of the present method.     

Evaluation of finite-plasticity theories for torsion-tension members made of tresca materials

Finite-incremental Tresca and von Mises theories are developed for solid circular-section torsion-tension members subjected to proportionate and nonproportionate loading. The materials are assumed to be isotropic and even. Two Tresca theories and a von Mises theory are compared with test data obtained from torsion-tension members. Three different kinds of steels were tested; they are hot-rolled mild steel, annealed mild steel, and hot-rolled SAE 1017 steel. The fully plastic values of axial load and torque predicted by the Tresca theories agree with the experimental results; however, the deformations, in the strain-hardening region, predicted by both of the Tresca theories were greater than observed. The von Mises theory is nonconservative in predicting the fully plastic loads of torsion members and torsion-tension members and in predicting the deformations of torsion members in the strain-hardening region, but gives good correlation between predicted and experimental deformations for the torsion-tension members in the strain-hardening region.     

NEW BOUNDARY ELEMENT METHOD FOR TORSION PROBLEMS OF CYLINDER WITH CURVILINEAR CRACKS

The Saint-Venant torsion problems of a cylinder with curvilinear cracks were considered and reduced to solving the boundary integral equations only on cracks. Using the interpolation models for both singular crack tip elements and other crack linear elements, the boundary element formulas of the torsion rigidity and stress intensity factors were given. Some typical torsion problems of a cylinder involving a straight, kinked or curvilinear crack were calculated. The obtained results for the case of straight crack agree well with those given by using the Gauss-Chebyshev integration formulas, which demonstrates the validity and applicability of the present boundary element method.