PREDICTION OF FATIGUE LIVES OF RC BEAMS STRENGTHENED WITH CFL UNDER RANDOM LOADING

The investigation on fatigue lives of reinforced concrete （RC） structures strength- ened with fiber laminate under random loading is important for the repairing or the strengthening of bridges and the safety of the traffic. In this paper, two methods are developed for predicting the fatigue lives of RC structures strengthened with carbon fiber [aminate （CFL） under random loading based on a residual life and a residual strength model. To discuss the efficiency of the model, 12 RC beams strengthened with CFL are tested under random loading by the MTS810 testing system. The predicted residual strength approximately agrees with test results.     

温度-随机载荷下CFL加固RC梁疲劳性能的实验研究

考虑亚热带地区公路桥梁的服役环境温度与车辆载荷的作用效应,本文以碳纤维薄板(CFL)加固钢筋混凝土(RC)桥梁结构为研究对象,利用本课题组构建的实验平台,提出了温度与车辆随机载荷耦合作用下CFL加固RC梁的疲劳实验方法。在3个温度和3个载荷水平下实施了温度-随机载荷耦合作用下的三点弯曲疲劳实验,初步探讨了温度-随机载荷作用下加固梁的疲劳破坏机理,并提出了温度-随机载荷耦合下加固梁疲劳寿命的半经验公式。     

循环载荷下碳纤维薄板增强RC梁的疲劳性能试验研究

以碳纤维薄板(CFL)增强RC梁为研究对象,通过对循环载荷作用下增强梁的三点弯曲疲劳试验研究,得到了增强梁的线性对数疲劳寿命曲线和跨中挠度的演化规律,外推得到了极限疲劳强度和抗弯刚度的演化规律,揭示了增强梁的疲劳破坏机理。循环载荷下CFL增强RC梁的破坏模式包括混凝土开裂、碳纤维薄板与混凝土界面剥离、主筋屈服等模式,疲劳破坏过程具有明显的损伤成核、稳定扩展、失稳扩展三阶段发展规律。与普通RC梁相比较,CFL增强RC梁的裂缝分布较均匀、密集,粘贴CFL对增强梁的初始抗弯刚度提高幅度较小,对疲劳损伤阶段的抗弯刚度则提高了约一倍。根据CFL增强RC梁的疲劳寿命曲线得到其极限疲劳强度为25.42 kN,为三点弯曲静载下极限承载力的58.5%。     

冻融循环下预应力CFRP板加固钢筋混凝土梁的耐久性研究

预应力CFRP加固混凝土结构技术由于具有显著优势,越来越多地被应用在桥梁加固中,本文针对冻融循环作用下预应力CFRP板加固钢筋混凝土梁的耐久性能进行了实验研究。通过12片加固梁试件的实验研究了不同次数冻融循环作用下预应力CFRP板加固梁的破坏形态和承载性能,分析了混凝土强度等级、冻融循环次数、CFRP初始应力水平等因素对加固梁耐久性能的影响。实验结果表明:经历冻融循环后试件的开裂荷载和极限承载能力都有了不同程度的下降,冻融侵蚀对CFRP加固混凝土结构产生了明显的不利影响;随着冻融循环次数的增加,加固试件的破坏模式逐渐由混凝土保护层剥离转变为界面剥离的破坏形态;冻融循环作用对预应力加固试件的整体不利影响要大于非预应力试件;混凝土强度为C60的预应力CFRP加固试件在冻融侵蚀作用下的退化要较强度为C30的加固试件显著。     

随机载荷下碳纤维薄板增强RC梁试验研究

桥梁等钢筋混凝土结构在运营期所受活载为随机载荷。研究随机载荷作用下碳纤维薄板(Carbon Fiber Laminate简称CFL)片材增强钢筋混凝土构件的疲劳性能,对于采用碳纤维薄板技术加固桥梁等混凝土结构有重要的指导意义。本文通过随机载荷作用下碳纤维薄板增强RC梁的三点弯曲疲劳试验,得到了增强梁的S-N曲线和跨中挠度的演化规律,揭示了随机载荷下增强梁的疲劳破坏机理。随机载荷下碳纤维薄板增强RC梁的破坏模式包括钢筋断裂、碳纤维薄板剥离、混凝土压坏等破坏形态,疲劳破坏过程具有明显的损伤成核、稳定扩展、失稳扩展的三阶段发展规律。     

碳纤维布加固钢筋混凝土梁受力性能的试验研究

通过对8根矩形截面钢筋混凝土梁的静力加载试验,研究了抗弯和抗剪两种加固方式对钢筋混凝土梁的破坏形态和力学性能的影响,对比分析了碳纤维加固率、试验梁的状态、混凝土强度对加固效果的影响。结果表明：经碳纤维抗弯哥口抗剪加固后加圉梁相应的力学性能指标值明显提高;混凝土裂缝扩展得到了有效延缓,加固效果明显;抗弯加固后可显著提高混凝土梁的承载力和延性,但提高程度并不与加固率成正比;预裂粱抗弯加固后承载力和延性得到提高,但与其相同加固参数的梁相比,其承载力和延性有所降低;抗剪加固时混凝土强度越高,加固后混凝土梁的承载力和变形能力提高幅度越大,其中混凝土梁的变形能力受混凝土强度的影响较大。最后,对加固梁的极限承载力进行了理论分析与计算,建立了实用的理论计算公式,计算结果与试验结果吻合较好。     

Experimental study and analysis of RC beams strengthened with CFRP laminates under sustaining load

Six reinforced concrete beams strengthened in flexure using carbon fiber reinforced polymer (CFRP) laminates subjected to different sustaining loads were tested. The main goal of the test is to examine the effects of initial load and load history on the ultimate strength of strengthened reinforced concrete beams by externally bonded CFRP laminates. The main experimental parameters include different levels of sustaining load at the time of strengthening and load history. To explain the experimental results in quantitative terms, a theoretical model for flexural behavior of the strengthened reinforced concrete beam is also developed. Test results in the current study show that sustaining load levels at the time of strengthening have important influence on the ultimate strength of strengthened reinforced concrete beams. If the initial load is basically same, the ultimate strength of reinforced concrete beams strengthened with CFRP laminates is almost same regardless of load history at the time of strengthening.     

先张预应力CFL加固RC梁预应力损失的实验研究

由于预应力碳纤维增强复合材料(CFRP)加固钢筋混凝土(RC)结构技术能够充分发挥其优异的力学性能而备受关注。本文以预应力碳纤维薄板(CFL)加固RC桥梁结构为研究对象,研制了采用先张法对CFL施加预应力的实验装置,提出了先张预应力CFL加固RC梁的实验方法及其预应力损失的监测方法,并在3个预应力水平下对RC梁实施了预应力CFL加固,测试和分析了CFL的预应力损失演化规律。研究结果表明,本文提出的先张预应力CFL加固RC梁以及预应力损失测试的方法是可行和有效的。     

碳纤维布与钢板复合加固梁剥离破坏研究

通过12根碳纤维布与钢板复合加固钢筋混凝土梁的抗弯性能研究,结果表明复合加固方式能有效地改善被加固构件的受力性能,但常由于复合加固层的剥离可能导致加固效果的降低。复合加固层与被加固构件之间的剥离是由于薄弱截面在剪应力及正应力的集中作用下而产生的,文中对复合加固层与混凝土之间的粘结剪应力及剥离正应力的计算公式分别进行推导,并进一步对碳纤维布与钢板复合加固的剥离机理进行分析,为工程应用提供依据。     

Prediction of bond failure and deflection of carbon fiber-reinforced plastic reinforced concrete beams

Carbon fiber-reinforced plastic (CFRP) reinforced concrete beams can fail due to interface debonding, due to the high tensile strength of such rebars. A set of 16 concrete beams reinforced with different amounts of CFRP reinforcement was subject to static three-point bending. The beam dimensions and CFRP reinforcements used were selected to demonstrate a transition from compression failure to bond failure with decreasing reinforcement ratio. It is shown that accurate bond strength data to predict such failures can be obtained from a “hinged-beam” test configuration, rather than the conventional direct “pull-out” tests. Deflection under service loads can also be predicted more accurately using a proposed equation that includes the reinforcement ratio and the elastic modulus of the reinforcement.     

THE FAILURE MODES OF CONCRETE BEAMS STRENGTHENED WITH NEAR SURFACE MOUNTED FRP BARS

为研究不同参数下表面内嵌纤维筋加固后T 形混凝土梁的破坏模式, 对5 根不同梁端锚固、FRP(fiber reinforced polymer) 筋表面特征和FRP 筋类型的T 形混凝土梁进行受弯性能试验. 结果表明, 无梁端锚固、光圆GFRP (glass fiber reinforced polymer) 筋和CFRP (carbon fiber reinforced polymer) 筋加固梁试件发生粘结破坏. 梁端锚固和FRP 筋表面特征影响加固梁试件的极限载荷, CFRP 筋加固梁试件的屈服载荷和极限载荷较大. 螺纹FRP 筋和有梁端锚固加固梁试件FRP 筋利用率较高. 因此, 有梁端锚固的表面内嵌螺纹GFRP 筋加固是最为有效的加固方式.     

Bending of simply-supported circular timber beam strengthened with fiber reinforced polymer简

The bending behavior of the circular cross-section timber beam strengthened with a fiber reinforced polymer (FRP) sheet is investigated. The tight bonding is on the interface between the surface of a timber beam and the reinforcement layer of the FRP sheet. An analytical expression for the bending moment-curvature relation is presented, and its failure modes are analyzed. The governing equation for nonlinear small deflection of the FRP-strengthened circular timber beam is established, and the corresponding numerical method is given. The bending deformation of the simply-supported circular timber beam strengthened with the carbon fiber reinforced polymer (CFRP) sheet subject to a uniform load is studied numerically. The influence of the angle and thickness of the CFRP layer as well as the timber strength on the bending deflection of the FRP-strengthened circular timber beam is examined. It is revealed that, with the increases of the thickness and angle, the deflection of the CFRP-strengthened circular timber beam is decreased, and its carrying capacity and ductility are increased. However, when the angle of the layer reaches a certain value, the deflection will no longer decrease with the increase of the angle. At the same time, the nonlinear bending moment-curvature relation of the CFRP-strengthened circular timber beam is simplified as an approximate bilinear constitutive model. The approximate deflections of the simply-supported circular timber beam strengthened with the CFRP sheet are obtained. The results are compared with the linearly elastic bending and nonlinear bending models, showing that the mid-span deflections of a CFRP-strengthened circular timber beam with the approximate bilinear constitutive model are greater than those with the nonlinear constitutive model. The results of its stiffness analysis are on the safe side.     

纤维布抗弯加固梁跨中剥离应力的近似计算

首先综述了纤维复合材料(FRP)抗弯加固梁中防剥离破坏的各种措施，分析了跨中混凝土保护层的剥离破坏机理，提出一个近似计算跨中保护层剥离应力上限的方法，可供防剥离设计参考。     

粘贴碳纤维布加固混凝土管道试验研究

首次通过对14个素混凝土和14个钢筋混凝土环状试件外粘碳纤维布加固性能进行试验，研究了碳纤维布加固混凝土内压圆管的破坏特征、受力性能和破坏机理。对不同加固方法及一次或二次受力的混凝土管在内压力作用下的极限承载力、荷载一应变关系等方面进行了研究。试验结果表明，用碳纤维布加固混凝土内压管可以显著地提高极限承载力，明显的改善了构件的延性，能够获得良好的力学性能。加固后试件的开裂承载力与未加固试件相比，提高幅度不大，加固试件二次受力与一次受力相比，开裂荷载有所降低，但极限承载力基本相同。用碳纤维布加固内压管是一个新课题，具有很好的应用前景，用本文提出的加固方法具有优良的加固性能，可为工程应用提供参考。     

Plasticity induced fatigue crack growth retardation model for steel elements reinforced by composite patch

Fatigue tests on notched steel plates reinforced by composite patch showed that the application of carbon fiber reinforced polymers (CFRP) strips with pretension of the overlays prior to bonding. This resulted in a significant amount of additional fatigue life. In particular, the pre-tension produces a compressive field in the steel plate which reduces the stress ratio that enhances crack growth retardation. The fatigue crack propagation rate is postulated to be a function of the effective strain energy density factor range. Fatigue crack growth data showed that standard crack growth retardation model cannot be used to evaluate the minimum effective stress. Hence, an ad hoc plasticity model is introduced and validated using experimental results. The proposed technique is an extension of the well know Newman’s model. The bridging effect due to the reinforcing strips is analytically modeled in order to estimate the reduction of crack opening displacement and finally the magnification of the crack growth retardation. Numerical and experimental results match well and show a significant influence of the pre-tension level on the expected fatigue crack growth rate of a reinforced steel plate.     

?????????????????????????

摘 要：利用大型通用有限元软件ANSYS10.0，首先对钢筋混凝土试件梁采用了三维的建模方式，然后对其抗弯性能进行了非线性数值模拟，所模拟的量包括各临界荷载、挠度、应力分布、中和轴的移动等，模拟结果与实测值吻合得很好。该方法可以用来分析钢筋混凝土梁板构件的承载能力，也可以应用在某些院校的教学中。     

模拟酸雨腐蚀下预应力混凝土梁的抗弯性能研究

为了探讨酸雨腐蚀环境对预应力混凝土梁抗弯性能的影响，制作了8根预应力混凝土梁，从混凝土强度等级、预应力度和钢绞线腐蚀率等方面，进行8根预应力混凝土梁的三分点静载试验。试验结果及分析表明，混凝土强度对屈服后试验梁的抗弯性能影响较大，对弹性阶段的刚度影响较小；随着预应力度的增加，试验梁的开裂荷载逐渐增大，进入裂缝阶段后，刚度下降速度逐渐加快；钢绞线腐蚀率越大，试验梁的极限抗弯承载力越低；腐蚀率在一定范围内（>3.22%），随着腐蚀率的增大，预应力混凝土梁试件的开裂弯矩、屈服弯矩和极限弯矩明显降低。根据试验结果，提出了模拟酸雨环境下预应力混凝土梁试件抗弯承载力的计算方法，同时采用ANSYS软件对预应力混凝土梁进行非线性有限元分析，将试验梁的计算值和模拟值与试验值进行比较，均吻合较好。     

FRP加固RC梁界面疲劳损伤红外检测分析

FRP-混凝土界面剥离损伤的探测是界面力学分析的一个难点。基于三个标准试件探讨了红外检测方法对FRP-混凝土界面剥离探测的精度、可行性以及剥离判断的标准,并对常幅疲劳荷载下FRP加固钢筋混凝土(RC)梁界面的疲劳行为进行了跟踪记录,分析了界面的疲劳破坏过程。试验结果表明,FRP加固RC梁界面存在初始的未粘结区,在疲劳加载的初期界面剥离快速增加,随后在大部分疲劳寿命期内保持稳定,在最后数千次加载循环内界面损伤失稳发展导致整个加固构件的破坏。文中基于红外数据给出了每个阶段的疲劳加载次数和界面剥离损伤的面积。     

Effective widths of rectangular slabs stiffened along two opposite edges by prestressed edge beams

The present analysis is an attempt to determine the portion of a rectangular slab that is acting with its two parallel stiffening edge beams, through which prestressing loads are applied to the entire section, in resisting load. Employing the well known theories of bending of plates and beams, the constitutive equations governing the behaviour of this type of composite system are presented. In particular, the equation of compatibility of strains between the slab edges and the stiffening edge beams at their junctions is formulated. In doing this, the biaxial nature of the bending of the edge beams, ignored in earlier formulations [1], has been incorporated. The results of the present analysis show that, under transverse loading, the portion of the slab, called the effectiv width, that can be considered effective as a part of each of the stiffening edge beams in determining stresses and deflexions is not significantly different from that obtained for an unprestressed section or a simply reinforced section. The effective width of the slab when such a section is subjected to only prestressing loads however shows a significant difference. We conclude from this that a single table of effective widths could be adopted for design purposes when considering transverse bending of this type of composite system whether the section is prestressed or not. Typical stress distributions due to (i) prestress alone, (ii) transverse loading alone and (ii) combined prestress and transverse loading are presented to demonstrate that the present formulation is versatile enough to solve problems involving prestressed edge beams in this type of composite assembly.     

钢板-混凝土组合加固钢筋混凝土梁的非线性有限元分析

以10根采用钢板-混凝土组合加固技术加固的钢筋混凝土梁的试验为基础,建立了钢板-混凝土组合加固钢筋混凝土梁的非线性有限元模型.沿用了钢板-混凝土组合梁有限元分析中栓钉的荷载-滑移曲线及断裂模型,提出了新老混凝土界面的剪切-滑移模型,可以较好地模拟界面受力性能.采用有限元软件ABAQUS,模拟了一次加固、不同损伤加固及持载加固等加载情况下加固构件受力全过程和受弯破坏以及新老混凝土剥离破坏等破坏形态下加固试件的受力性能.在验证了有限元模型的准确性后,分析了钢板厚度、加固部分高度及长度等参数对加固构件承载能力及刚度的影响.最后提出了几点对钢板-混凝土组合加固RC梁的设计建议.