一种计算复合材料等效弹性性能的有限元方法

在最小二乘意义下提出了一种计算复合材料等效弹性性能的有限元方法.这种方法由于考虑了等效弹性张量各分量之间的耦合关系,所求得的等效弹性常数比传统方法更可靠,可适用于求解含任意形状的夹杂和夹杂物问题.通过算例计算了在不同弹性模量对比度下两相复合材料的等效弹性性能,并与相关的理论及数值结果进行了比较,结果表明,利用该方法计算含夹杂复合材料等效弹性常数是可行的.     

水泥砂浆界面相弹性常数的反演计算

为了计算水泥砂浆界面过渡区的弹性常数,采用广义自洽方法(GSCM),根据水泥砂浆内部的微细观结构,建立了由水泥浆基体、岩石离散夹杂(骨料)、界面过渡区(ITZ)和有效弹性材料组成的四相复合材料模型.推导了界面相的体积模量和剪切模量方程.利用已知水泥砂浆材料的实验数据,计算了界面相的弹性常数.发现界面相剪切模量约为水泥浆基体剪切模量的50%.     

功能梯度界面相对周期分布纤维增强复合材料反平面剪切的影响

基于复变函数理论和边界配点法,探索了功能梯度界面相在周期均匀分布纤维增强复合材料反平面剪切问题中所起的作用。由于纤维在复合材料基体中的周期分布是均匀的,将其简化成含一功能梯度界面相夹杂的方形单胞。采用分层均匀化方法,将功能梯度界面相离散成K层界面层。当K足够大时,每个界面层可视为匀质材料,同时计算得到的复合材料宏观性能趋于定值。根据单胞内的基体、界面相和夹杂的几何外形特点,分别给出复势函数的级数形式,这些复势函数在各组分的相邻界面应满足连续性条件,在单胞的外边界应满足周期性边界条件和远场加载条件,从而确定复势函数中的待定系数,进而根据平均场理论确定复合材料有效模量。主要探讨了夹杂体积分数、各组分模量、功能梯度界面相的模量渐变形式等因素对纤维增强复合材料性能的影响。结果表明：不管基体模量相对于夹杂模量是大还是小,都有对应的界面相模量渐变形式可使夹杂周围的等效应力集中系数减小;另外还发现仅当夹杂模量较大时,功能梯度界面相模量的变化方式对复合材料有效模量产生不可忽视的影响。     

考虑夹杂相互作用的复合陶瓷夹杂界面的断裂分析

复合材料中夹杂含量较高时,夹杂间的相互作用能显著改变材料细观应力应变场分布,基体和夹杂中的平均应力应变水平也会发生较大变化,导致复合材料强度等力学性能发生显著变化. 为修正单一夹杂模型运用在实际材料中的误差,基于相互作用直推估计法,建立一种考虑含夹杂相互作用的夹杂界面裂纹开裂模型. 首先根据相互作用直推估计法,得到残余应力和外载应力共同作用下夹杂中的平均应力,再计算无限大基体中相同的夹杂达到相同应力场时的等效加载应力,将此加载应力作为含界面裂纹夹杂的等效应力边界条件,在此边界条件下求得界面裂纹尖端的应力强度因子,进而得到界面裂纹开裂的极限加载条件,并分析了夹杂弹性性能、含量、热残余应力、夹杂尺寸等因素对界面裂纹开裂条件的影响. 结果表明,方法能够有效修正单夹杂模型运用在实际材料中的误差,较大的残余应力对界面裂纹开裂有重要的影响,夹杂刚度的影响并非单调且比较复杂;在残余应力较小时,降低柔性夹杂刚度或者增大刚性夹杂刚度都有利于提高材料强度;扩大夹杂尺寸将导致裂纹开裂极限应力显著降低,从而降低材料强度.      

含非完好界面粒子增强复合材料对弹性波的散射

采用波函数展开的方法研究了非完好界面条件下圆球形夹杂对弹性波的散射。以非完好界面的弹簧模型为基础，通过适当选取弹簧常数，研究了法向和切向界面参数对纵波和横波不同的散射效果。考虑了单个圆球夹杂的散射和颗粒增强复合材料中弹性波的多重散射，研究了复合材料中的有效波速和动态有效弹性常数。并针对金属基颗粒增强复合材料SiC-Al...     

考虑粒子分布特征的复合材料细观力学方法

研究了颗粒增强复合材料中颗粒增强体粒径分布对复合材料力学性能的影响,利用分形思想将增强粒子的概率分布特征考虑进来,对已有的复合材料细观力学等效夹杂方法进行修正,建立了一个考虑粒子统计分布的细观等效力方法.以混凝土为例,分析了颗粒增强体体积含量、夹杂与基体的模量比和分形结构的分辨率对复合材料力学性能的影响.结果表明,这种新方法能够适用于分析颗粒增强复合材料的细观结构对力学性能的影响.     

含椭圆夹杂正交各向异性体的界面应力研究

本文研究了远场作用反平面载荷时含椭圆夹杂正交各向异性体的界面应力分布规律．利用解析函数边值问题理论和共形映射技术,推导了反平面载荷下含椭圆夹杂正交异性体的精确解,获得了夹杂和基体内应力场的闭合解,并通过有限元结果验证了本文解析解的有效性．研究表明：基体材料主方向弹性模量比C55/C44和夹杂形状比 对界面应力影响显著;基体材料主方向模量比C55/C44对界面应力的影响受夹杂/基体模量比Cf/C44的限制．     

界面对金属基复合材料轴向弹塑性拉伸性能的影响及局部应力场的分析

本文建立在广义自洽有限元迭代平均化方法的基础上，计算了存在弹性界面相的ＳｉＣ晶须增强铝基复合材料的轴向弹塑性拉伸性能。研究了界面厚度以及界面在不同纤维长径比和体分比情况下对复合材料轴向拉伸性能的影响。本文同时分析了界面材料性质的分布形式对复合材料的拉伸性能及局部应力场的影响     

NiMnGa颗粒/环氧树脂复合材料的力学性能研究

将通过球磨法获得的Ni2MnGa颗粒与双酚A二缩水甘油醚环氧树脂混合均匀并常温固化,制备出相应的复合材料试件;通过拉伸-卸载试验研究了NiMnGa颗粒对树脂基体的增强效果;以试验为基础,从细观力学的角度分析了NiMnGa颗粒对树脂基复合材料弹性特性的影响;采用商用有限元软件Abaqus,对NiMnGa/树脂复合材料单胞模型进行了仿真计算。分析结果表明:随着NiMnGa颗粒体积含量的增加,试件的拉伸模量和剪切模量增大、泊松比减小;随着椭圆NiMnGa颗粒长短半轴比的减小,复合材料纵向泊松比增加、纵向拉伸模量减小,横向拉伸模量呈先减后增的趋势,剪切模量则呈先增后减的趋势。通过对比可知试验值、理论值、有限元模拟值数值相近且变化趋势一致。     

2124 Al/SiC_p复合材料的动态变形行为及微结构效应

研究了在动态压缩时２１２４Ａｌ／ＳｉＣｐ复合材料的变形行为与微结构效应．分析结果表明，对于给定材料，复合材料的流动应力主要取决于微结构尺度效应．若增强相尺寸，基体晶粒尺寸以及增强相间距三者大小相当，则复合材料的流动应力取决于增强相的分散程度和位错密度；若增强相尺寸及其间距大小相当，但比基体晶粒大得多，那复合材料的流动应力主要取决于增强相的分散度．微观观测发现在同样加载条件下，变形局部化更容易在含较小碳化硅颗粒的复合材料内形成；变形区内的微损伤几乎都是基体与粒子界面脱粘和粒子角点邻近的微裂纹．对于所研究的这类复合材料，弹性模量及应变硬化几乎不受增强颗粒尺寸影响．     

界面特性对短纤维金属基复合材料蠕变行为的影响

基于短纤维增强金属基复合材料(MMC)的单纤维三维模型(三相)，利用粘弹性有限元分析方法对影响金属基复合材料的蠕变行为的因素进行了较为系统的分析。研究中主要讨论了界面特性和纤维取向角对金属基复合材料的蠕变性能的影响。研究结果发现，界面特性诸如厚度、模量和应力指数都对纤维最大轴应力和稳定蠕变率产生影响：稳态蠕变率随界面模量的增大而逐渐减小，当高于基体模量时基本保持不变；纤维轴应力的变化与蠕变率正好相反。稳态蠕变率随界面厚度、应力指数的增加而增大；而轴应力则随之减小。同时不同的纤维取向也影响金属基复合材料蠕变时的轴应力分布和稳态蠕变率。     

Investigation of effective material properties in composites with internal defect or reinforcement particles

This paper is concerned with the investigation of the effective material properties of internally defective or particle-reinforced composites. An analysis was carried out with a novel method using the two-dimensional special finite element method mixing the concept of equivalent homogeneous materials. A formulation has been developed for a series of special finite elements containing an internal defect or reinforcement in order to assure the high accuracy especially in the vicinity of defects or reinforcements. The adoption of the special finite element can greatly simplify numerical modeling of particle-composites. The numerical result provides the effective material properties of particle-reinforced composite and explains that the size of particles has great influence on the material properties. Numerical examples also demonstrate the validity and versatility of the proposed method by comparing with existing results from literatures.     

基于等效特征应变原理的复合材料有效模量细观力学分析

基于等效特征应变原理,提出了一种新的复合材料有效模量细观力学分析方法。首先,在等效特征应变原理基础上提出平均等效特征应变原理,它可用于解决有限体下任意形状(无论是凸或凹形)的单个夹杂或多个夹杂的弹性变形问题。其次,将平均等效特征应变原理与细观力学直接均匀法相结合,来分析确定复合材料的有效模量。最后利用复合材料纤维与基体的力学性能参数及纤维的体分比,借助MATLAB编程方法,预测其有效模量。通过将理论预测值与已有的的试验值、其它理论预测值进行对比,验证了新分析方法的合理性和分析精度。     

FRP-混凝土界面粘结行为的参数影响研究

FRP-混凝土界面的粘结性能对FRP加固混凝土结构力学行为和破坏模式有着重要影响。本文对表征FRP-混凝土界面粘结性能的三个重要参数(界面初始刚度、最大剪应力、界面破坏能)开展研究,通过13个单剪试件的试验考察了混凝土强度、胶层厚度和粘结长度等因素对界面粘结行为的影响,根据试验结果拟合了界面破坏能、最大剪切应力与胶层剪切刚度、混凝土强度之间的函数关系。在试验研究基础上,构建了外贴FRP-混凝土界面粘结的有限元模型。通过有限元分析考察了界面破坏能等三个参数不变的前提下,不同的局部粘结滑移本构关系对界面粘结行为的影响;进而研究了其中一个参数变化时引起的界面粘结性能改变。研究结果表明:界面粘结承载力随着胶层厚度增加而逐渐提高;胶层厚度与界面破坏能成正比,与峰值剪应力成反比;当界面破坏能等三个参数保持不变时,局部粘结滑移本构关系对FRP-混凝土界面粘结性能的影响较小;三个参数中的一个增大时将延缓界面破坏的过程。     

Stability and finite strain of homogenized structures soft in shear: Sandwich or fiber composites,and layered bodies

The stability theories energetically associated with different finite strain measures are equivalent if the tangential moduli are transformed as a function of the stress. However, for homogenized soft-in-shear composites, they can differ greatly if the material is in small-strain and constant elastic moduli measured in small-strain tests are used. Only one theory can then be correct. The preceding variational energy analysis showed that, for sandwich columns and elastomeric bearings, respectively, the correct theories are Engesser’s and Haringx’s, associated with Green’s and Almansi’s Lagrangian strain tensors, respectively. This analysis is reviewed, along with supporting experimental and numerical results, and is then extended to arbitrary multiaxially loaded homogenized soft-in-shear orthotropic composites. It is found that, to allow the use of constant shear modulus when the material is in small strain, the correct stability theory is associated with a general Doyle–Ericksen finite strain tensor of exponent m depending on the principal stress ratio. Further it is shown that the standard updated Lagrangian algorithm for finite element analysis, which is associated with Green’s Lagrangian finite strain, can give grossly incorrect results for homogenized soft-in-shear structures and needs to be generalized for arbitrary finite strain measure to allow using constant shear modulus for critical loads at small strain.     

一种考虑界面相物性影响的界面单元法

界面是由复杂的界面相简化而成的,界面破坏实际是界面相材料的破坏。数值计算为了方便,如经典模型和内聚力模型等,都把很薄的界面相作无厚度化处理。导致只能考虑界面的面力,而无法考虑界面相内的应力(平行于界面方向的应力)。使界面失效准则先天性地排除了界面相内部应力的影响,从界面相材料失效机理的角度来看这是不够严谨的。本文将界面相材料等效为一种弹性连续体,由界面本构关系推导得到了一种新的界面单元。该单元具有界面参数易确定、对界面相物性可以进行等效描述等优点。通过商用有限元软件ABAQUS和用户子程序UEL实现了数值分析,并与直接物理模型的数值模拟结果进行对比,证明了本方法的简便及准确性。通过对不同界面相厚度结构的进一步分析,探讨了本文方法的可行范围。     

The averaged mechanical properties of prismatic lattice formed by ellipsoidal inclusions

Summary The objective of this paper is to evaluate the averaged elastic properties of 3-D grained composites in which identical inclusions form a prismatic network interacting with the matrix material. The inclusions are of ellipsoidal shape with transverse circular sections located at the nodes of a doubly-periodic lattice with an orthogonal elementary cell. When the arrays of inclusions are set at equal spacings in normal directions through the thickness of the matrix, the material formed is an anisotropic composite with tetragonal symmetry at planes transverse to the fiber axis. The longitudinal and transverse elastic and shear moduli as well as the longitudinal Poisson's ratios of such composites are evaluated in this paper. The averaged properties are studied in terms of the aspect ratio and volume fraction of the inclusions as well as the relative rigidity of the constituent phases. Employing the Eshelby's theory for the stress field around a single ellipsoidal inhomogeneity, which is surrounded by the effective anisotropic material, and considering the Mori-Tanaka's concept for the mutual interaction of the neighboring inclusions, we may evaluate the averaged elastic properties of grained composites with aligned ellipsoidal inclusions at finite concentrations. The results provided in a closed-form solution concern the stiffness of 3-D grained composites with parallely dispersed ellipsoidal inclusions forming a prismatic network inside the principal material. It is shown that the stiffness is affected by both the geometry of the inclusions and their concentration. The use of different composite models in the analysis shows that intense variations of stiffness occur mainly in hard composites weakened by soft ellipsoidal inclusions. These findings come in full verification with experimental or theoretical results from the literature. Received 10 February 1998; accepted for publication 27 November 1998     

Influences of reinforcing particle and interface bonding strength on material properties of Mg/nano-particle composites

In the present study, an effective model is proposed to predict the effective elastic behavior of the three-phase composite containing spherical inclusions, each of which is surrounded by an interphase layer. The constitutive equations are derived for the stress and strain of each phase of the composite subjected to a far-field tension. Based on these constitutive laws, the effective bulk, shear and Young’s modulus are obtained. A statistical debonding criterion is adopted to characterize the varying probability of the evolution of interphase debonding. Influences of debonding damage, particle volume fraction, interphase properties and bonding strength on overall mechanical behavior of composites are also discussed. Numerical analyses are carried out on particle-reinforced composites and the predictions have a good agreement with the experimental results.     

超重力作用下软材料薄膜失稳的有限元分析

软材料在自然界和工业应用中无处不在，其显著特点是对外界刺激极其敏感，相对于传统材料其弹性模量更小，容易发生表面形态的失稳现象．现有研究主要把光、声、电等作为诱导材料失稳的因素进行研究，而重力往往作为常量考虑．本文通过有限元模拟，建立超重力作用下环向受限的圆柱状软材料薄膜失稳模型，探究了薄膜材料的密度、厚度、半径、剪切模量等材料和几何参数对失稳临界超重力和临界失稳模态的影响．结果表明，触发薄膜失稳的超重力随薄膜厚度和密度增大而减小，随剪切模量增大而增大，随着薄膜半径增大快速减小并迅速趋于常数．另外，当径厚比R/H较小时，无量纲临界超重力随着径厚比增大而单调减小，但当径厚比R/H大于3 时，此量为一个常数．超重力作用下软材料的临界失稳模态与密度、剪切模量等参数无关，随径厚比R/H增大，临界失稳模态波数增大、波长减小．     

Effective mechanical properties of unidirectional composites in the presence of imperfect interface

In this paper, the equivalent inclusion method is implemented to estimate the effective mechanical properties of unidirectional composites in the presence of an imperfect interface. For this purpose, a representative volume element containing three constituents, a matrix, and interface layer, and a fiber component, is considered. A periodic eigenstrain defined in terms of Fourier series is then employed to homogenize non-dilute multi-phase composites. In order to take into account the interphase imperfection effects on mechanical properties of composites, a stiffness parameter in terms of a matrix and interphase elastic modulus is introduced. Consistency conditions are also modified accordingly in such a way that only the part of the fiber lateral stiffness is to be effective in estimating the equivalent composite mechanical properties. Employing the modified consistency equations together with the energy equivalence relation leads to a set of linear equations that are consequently used to estimate the average values of eigenstrain in non-homogeneous phases. It is shown that for composites with both soft and hard reinforcements, largest stiffness parameter that indicates complete fiber–matrix interfacial debonding causes the same equivalent lateral properties.