STUDY ON THE OVERALL PRESSURE BALANCE OF A DOWNFLOW CIRCULATING FLUIDIZED BED SYSTEM

A pressure balance model for a circulating fluidized bed unit that incorporates a downer has been proposed. The model predictions were validated with the experimental data obtained from a special cold-model circulating fluidized bed. Comparison of the operation stability between a CFB downer and a CFB riser has been carried out. Only one critical gas velocity exists in the CFB-riser for a given riser solids flux, while there can be many critical gas velocities for the operation of a CFB downer. Therefore, it is possible to achieve high solids concentration in a CFB downer if appropriate operating conditions are used.     

Evaluation of the effect of wall boundary conditions on numerical simulations of circulating fluidized beds

A computational fluid dynamics (CFD) modeling of the gas–solids two-phase flow in a circulating fluidized bed (CFB) riser is carried out. The Eularian–Eularian method with the kinetic theory of granular flow is used to solve the gas–solids two-phase flow in the CFB riser. The wall boundary condition of the riser is defined based on the Johnson and Jackson wall boundary theory (Johnson & Jackson, 1987) with specularity coefficient and particle–wall restitution coefficient. The numerical results show that these two coefficients in the wall boundary condition play a major role in the predicted solids lateral velocity, which affects the solid particle distribution in the CFB riser. And the effect of each of the two coefficients on the solids distribution also depends on the other one. The generality of the CFD model is further validated under different operating conditions of the CFB riser.     

Evaluation of the effect of wall boundary conditions on numerical simulations of circulating fluidized beds

A computational fluid dynamics （CFD） modeling of the gas-solids two-phase flow in a circulating fluidized bed （CFB） riser is carried out. The Eularian-Eularian method with the kinetic theory of granular flow is used to solve the gas-solids two-phase flow in the CFB riser. The wall boundary condition of the riser is defined based on the Johnson and Jackson wall boundary theory （Johnson ＆ Jackson, 1987） with specularity coefficient and particle-wall restitution coefficient.The numerical results show that these two coefficients in the wall boundary condition play a major role in the predicted solids lateral velocity, which affects the solid particle distribution in the CFB riser. And the effect of each of the two coefficients on the solids distribution also depends on the other one. The generality of the CFD model is further validated under different operatin~ conditions of the CFB riser.     

Modeling and simulation of circulating fluidized bed reactors applied to a carbonation/calcination loop

A fluid dynamic model for a gas-solid circulating fluidized bed （CFB） designed using two coupled riser reactors is developed and implemented numerically with code programmed in Matlab. The fluid dynamic model contains heat and species mass balances to calculate temperatures and compositions for a carbonation/calcination loop process. Because of the high computational costs required to resolve the three-dimensional phenomena, a model representing a trade-offbetween computational time requirements and accuracy is developed. For dynamic processes with a solid flux between the two reactor units that depends on the fluid dynamics of both risers, a dynamic one-dimensional two-fluid model is sufficient. A two-fluid model using the constant particle viscosity closure for the stress term is used for the solid phase, and an algebraic turbulence model is applied to the gas phase. The numerical model implementa- tion is based on the finite volume method with a staggered grid scheme. The exchange of solids between the reactor units constituting the circulating fluidized bed （solid flux） is implemented through additional mass source/sink terms in the continuity equations of the two phases, For model validation, a relevant experimental analysis provided in the literature is reproduced by the numerical simulations, The numerical analysis indicates that sufficient heat integration between the two reactor units is important for the performance of the circulating fluidized bed system, The two-fluid model performs fairly well for this chemical process operated in a CFB designed as two coupled riser reactors. Further analysis and optimization of the solution algorithms and the reactor coupling strategy is warranted.     

Modeling and simulation of circulating fluidized bed reactors applied to a carbonation/calcination loop

A fluid dynamic model for a gas-solid circulating fluidized bed (CFB) designed using two coupled riser reactors is developed and implemented numerically with code programmed in Matlab. The fluid dynamic model contains heat and species mass balances to calculate temperatures and compositions for a carbonation/calcination loop process.Because of the high computational costs required to resolve the three-dimensional phenomena, a model representing a trade-off between computational time requirements and accuracy is developed. For dynamic processes with a solid flux between the two reactor units that depends on the fluid dynamics of both risers, a dynamic one-dimensional two-fluid model is sufficient.A two-fluid model using the constant particle viscosity closure for the stress term is used for the solid phase, and an algebraic turbulence model is applied to the gas phase. The numerical model implementation is based on the finite volume method with a staggered grid scheme. The exchange of solids between the reactor units constituting the circulating fluidized bed (solid flux) is implemented through additional mass source/sink terms in the continuity equations of the two phases.For model validation, a relevant experimental analysis provided in the literature is reproduced by the numerical simulations. The numerical analysis indicates that sufficient heat integration between the two reactor units is important for the performance of the circulating fluidized bed system.The two-fluid model performs fairly well for this chemical process operated in a CFB designed as two coupled riser reactors. Further analysis and optimization of the solution algorithms and the reactor coupling strategy is warranted.     

Solids flow diagram of a CFB riser using Geldart B-type powders

Riser operating modes are vital to designing a circulating fluidized bed (CFB) reactor for a required process of either a gas-solid or a gas-catalytic nature. Different operating modes provide different solids’ residence times and mixing behaviors, which define the reactions’ efficiency and yield. The literature demonstrates distinct operating modes resulting from observed differences in slip factors and the range of particle velocities and their associated residence time distribution. The present research uses positron emission particle tracking (PEPT) in a riser of B-type bed material to determine the different operating modes by measuring (i) particle velocities and residence time distribution, (ii) population densities of these particles in the cross-sectional area of the riser, and (iii) solids flow pattern at the bottom of the riser. Data treatment defines four distinct solids hold-up regimes in the riser and proposes a "phase diagram" depicting the existence of the different operating modes (dilute, dense, core-annulus and combined) as a function of the superficial gas velocity and solids circulation flux in the riser. The delineated regimes have good agreement with available literature data and known industrial operations. Comparison with literature data for risers using A-type powders is also fair. The diagram enables CFB designers to better delineate operating characteristics.     

Rotational asymmetry of reactant concentration and its evolution in a circulating fluidized bed riser

Rotational asymmetric distribution of reactant (ozone) concentration and its evolution along with the gas-solid reactive flow were studied in a 76 mm i.d., 10.2 m high circulating fluidized bed (CFB) riser reactor. The superficial gas velocity ranged from 3 to 5 m/s and the solids circulation rates were 50 and 100 kg/(m² s). Experimental results show that the asymmetry of reactant distribution can extend to a height close to the length of flow developing zone of the CFB riser reactor and then disappears. Based on the hydrodynamics of the gas and solid phases in the solids entrance region, this asymmetry can be attributed to the effect of the solids entrance structure.     

Numerical investigations on gas–solid flow in circulating fluidized bed risers using a new cluster-based drag model

A cluster-based drag model is proposed for the gas–solid circulating fluidized bed (CFB) riser by including the cluster information collected from image processing and wavelet analysis into the calculation of system drag. The performance of the proposed drag model is compared with some commonly used drag models. A good agreement with the experimental data is achieved by the proposed cluster-based drag model. Error analysis of the proposed cluster-based drag model based on the local distributions of solids holdup and particle velocity is conducted. The clustering phenomenon in the low-density and high-density CFB risers and the effect of the cluster size on the simulation accuracy are also numerically studied by the proposed drag model.     

Non-uniform distribution of gas–solid flow through six parallel cyclones in a CFB system: An experimental study

In large-scale circulating fluidized bed (CFB) boilers, it is common to use multiple cyclones in parallel for the capture of solids, assuming that gas–solid flow to be the same in the cyclones. This article presents a study investigating gas–solid flow through six parallel cyclones in a CFB cold test rig. The six cyclones were located asymmetrically on the left and right walls of the riser. Solid volume fraction and particle velocity profiles at the riser outlets and in the horizontal ducts were measured using a fiber optical probe. Cyclone pressure drop and solid circulating rate were measured for each individual cyclone. Measurements showed good agreement as to the non-uniform distribution of the gas–solid flow, which occurred mainly across the three cyclones on one side: the middle cyclones on both sides had higher particle velocities. Conversely, the solid volume fractions, solid fluxes and solid circulating rates of the middle cyclones were lower than those of the other four cyclones. The apparent reason for the flow non-uniformity among the cyclones is the significant flow non-uniformity at the riser outlets. Under typical operating conditions, the solid volume fractions at the riser outlets had a deviation of up to 26% whereas the solid circulating rates at the stand pipes, 7%. These results are consistent with most other studies in the literature.     

Hydrodynamic characteristics of a rectangular gas-driven inverse liquid-solid fluidized bed

The hydrodynamic characteristics of a rectangular gas-driven inverse liquid-solid fluidized bed (GDFB) using particles of different diameters and densities were investigated in detail. Rising gas bubbles cause a liquid upflow in the riser portion, enabling a liquid downflow that causes an inverse fluidization in the downer portion. Four flow regimes (fixed bed regime, initial fluidization regime, complete fluidization regime, and circulating fluidization regime) and three transition gas velocities (initial fluidization gas velocity, minimum fluidization gas velocity, and circulating fluidization gas velocity) were identified via visual observation and by monitoring the variations in the pressure drop. The axial local bed voidage (ε) of the downer first decreases and then increases with the increase of the gas velocity. Both the liquid circulation velocity and the average particle velocity inside the downer increase with the increase of the gas velocity in the riser, but decrease with the particle loading. An empirical formula was proposed to successfully predict the Richardson-Zaki index “n”, and the predicted ε obtained from this formula has a ±5% relative error when compared with the experimental ε.     

Experimental study of the effect of friction phenomena on actual and calculated inventory in a small-scale CFB riser

Accurate information concerning riser inventory in a fluidized bed is required in some applications such as the calcium looping process,because it is related to the CO_2 capture efficiency of the system.In a circulating fluidized bed(CFB),the riser inventory is normally calculated from the riser pressure drop;however,the friction and the acceleration phenomena may have a significant influence on the total riser pressure drop.Therefore,deviation may occur in the calculation from the actual mass.For this reason the magnitude of the friction and the acceleration pressure drop in the entire riser is studied in small-scale risers.Two series of studies were performed:the first one in a scaled cold model riser of the 10 kW_(th)facility,and the second one in the 10kW_(th) fluidized bed riser under process conditions.The velocities were chosen to comply with the fluidization regimes suitable for the calcium looping process,namely,the turbulent and the fast.In cold-model experiments in a low-velocity turbulent fluidization regime,the actual weight(static pressure drop) of the particles is observed more than the weight calculated from a recorded pressure drop.This phenomenon is also repeated in pilot plant conditions.In the cold-model setup,the friction and acceleration pressure drop became apparent in the fast fluidization regime,and increased as the gas velocity rose.Within calcium looping conditions in the pilot plant operation,the static pressure drop was observed more than the recorded pressure drop.Therefore,as a conservative approach,the influence of friction pressure drop may be neglected while calculating the solid inventory of the riser.The concept of transit inventory is introduced as a fraction of total inventory,which lies in freefall zones of the CFB system.This fraction increases as gas velocity rises.     

Circulating turbulent fluidization—A new fluidization regime or just a transitional phenomenon

While circulating fluidized bed （CFB） reactor has many advantages over the more conventional turbulent fluidized bed （TFB） reactor, it does at least have one significant shortcoming-the rather dilute solids volume concentration in CFB reactor gives rise to less ideal reaction intensity. On the other hand, while having higher reaction intensity, TFB reactor has one fatal drawback of particle back-mixing, making it not suitable for certain reactions such as catalytic reaction where the catalyst requires frequent regeneration. This paper describes some key issues in the development of a circulating turbulent fluidized bed （CTFB） reactor that combines the advantages of both TFB and CFB, that is, to have the high reaction intensity as in TFB but and also to have a suppressed solids back-mixing as in CFB due to a continuous net upflow of solids flux through the bed. Experimental results show enough evidence to suggest that a new fluidization regime is formed, the characteristics of which appears to be distinct from those observed in a regular TFB and from those in either the bottom or the upper sections of regular CFB and/or high-density CFB （HDCFB）. Fundamentally, the difference is that particle-particle interaction （collision） dominates the motion of particles in CTFB and TFB, while gas-particle interaction （drag force） is the key element that determines the two phase flow in CFB including HDCFB.     

Numerical investigations on gas-solid flow in circulating fluidized bed risers using a new cluster-based drag model

A cluster-based drag model is proposed for the gas-solid circulating fluidized bed (CFB) riser by including the cluster information collected from image process...     

Quantitative measurement of solids distribution in gas–solid riser flows using electrical impedance tomography and gamma densitometry tomography

An electrical impedance tomography (EIT) system has been developed to non-invasively measure particle distributions in the riser of a pilot-scale circulating fluidized bed (CFB). Although EIT systems have often been applied to yield qualitative information about gas–solid flows, the present EIT system yields quantitative information that is validated by comparison to a gamma densitometry tomography (GDT) system. EIT and GDT were applied to the CFB riser (14-cm inner diameter, 5.77-m height) containing fluid catalytic cracking particles in air. The flows examined were annular with a dilute core and had average and near-wall solids volume fractions up to 0.25 and 0.66, respectively. For all cases, the average and near-wall solids volume fractions from EIT and GDT agreed to within 0.03 and 0.07, respectively. This good agreement suggests that, where feasible, EIT can be used in place of GDT, which is advantageous since EIT systems are often safer, less expensive, and faster than GDT systems.     

Particle size distribution in CPFD modeling of gas–solid flows in a CFB riser

A computational particle fluid dynamics (CPFD) numerical method to model gas–solid flows in a circulating fluidized bed (CFB) riser was used to assess the effects of particle size distribution (PSD) on solids distribution and flow. We investigated a binary PSD and a polydisperse PSD case. Our simulations were compared with measured solids concentrations and velocity profiles from experiments, as well as with a published Eulerian-Eulerian simulation. Overall flow patterns were similar for both simulation cases, as confirmed by experimental measurements. However, our fine-mesh CPFD simulations failed to predict a dense bottom region in the riser, as seen in other numerical studies. Above this bottom region, distributions of particle volume fraction and particle vertical velocity were consistent with our experiments, and the simulated average particle diameter decreased as a power function with riser height. Interactions between particles and walls also were successfully modeled, with accurate predictions for the lateral profiles of particle vertical velocity. It was easy to implement PSD into the CPFD numerical model, and it required fewer computational resources compared with other models, especially when particles with a polydisperse PSD were present in the heterogeneous flow.     

Effect of static bed height in the upper fluidized bed on flow behavior in the lower riser section of a coupled reactor

To study olefin reduction by using an auxiliary reactor for FCC naphtha upgrading, a large-scale cold model of a riser-bed coupled to an upper fluidized bed was established. The effect of static bed height in the upper fluidized bed on particle flow behavior in the lower riser was investigated experimentally. A restriction index of solids holdup was used to evaluate quantitatively the restrictive effect of the upper fluidized bed. Experimental results show that, under the restrictive effect of the upper fluidized bed, the riser could be divided into three regions in the longitudinal direction: accelerating, fully developed and restriction. The axial distribution of solids holdup in the riser is characterized by large solids holdup in the top and bottom sections and small solids holdup in the middle section. Overall solids holdup increased with increasing static bed height in the upper fluidized bed, while particle velocity decreased. Such restrictive effect of the upper fluidized bed could extend from the middle and top sections to the whole riser volume when riser outlet resistance is increased, which increases with increasing static bed height in the upper fluidized bed. The upper bed exerts the strongest restriction on the area close to the riser outlet.     

Effect of static bed height in the upper fluidized bed on flow behavior in the lower riser section of a coupled reactor

To study olefin reduction by using an auxiliary reactor for FCC naphtha upgrading, a large-scale cold model of a riser-bed coupled to an upper fluidized bed was established. The effect of static bed height in the upper fluidized bed on narticle flow behavior in the lower riser was investigated experimentally. A restriction index of solids holdup was used to evaluate quantitatively the restrictive effect of the upper fluidized bed. Experimental results show that, under the restrictive effect of the upper fluidized bed, the riser could be divided into three regions in the longitudinal direction： accelerating, fully developed and restriction. The axial distribution of solids holdup in the riser is characterized by large solids holdup in the top and bottom sections and small solids holdup in the middle section. Overall solids holdup increased with increasing static bed height in the upper fluidized bed, while particle velocity decreased. Such restrictive effect of the upper fluidized bed could extend from the middle and top sections to the whole riser volume when riser outlet resistance is increased, which increases with increasing static bed height in the upper fluidized bed. The upper bed exerts the strongest restriction on the area close to the riser outlet.     

THERMAL BOUNDARY LAYER IN CFB BOILER RISER

Measurement of temperature profiles of gas-solid two-phase flow at different heights in commercial-scale circulating fluidized bed (CFB) boilers was carried out. Experimental results showed that the thickness of thermal boundary layer was generally independent of the distance from the air distributor, except when close to the riser outlet. Through analysis of flow and combustion characteristics in the riser, it was found that the main reasons for the phenomena were: 1) the hydrodynamic boundary layer was thinner than the thermal layer and hardly changed along the CFB boiler height, and 2) both radial and axial mass and heat exchanges were strong in the CFB boiler. Numerical simulation of gas flow in the outlet zone confirmed that the distribution of the thermal boundary layer was dominated by the flow field characteristics.     

Experimental study of the effect of friction phenomena on actual and calculated inventory in a small-scale CFB riser

Accurate information concerning riser inventory in a fluidized bed is required in some applications such as the calcium looping process, because it is related to the CO₂ capture efficiency of the system. In a circulating fluidized bed (CFB), the riser inventory is normally calculated from the riser pressure drop; however, the friction and the acceleration phenomena may have a significant influence on the total riser pressure drop. Therefore, deviation may occur in the calculation from the actual mass. For this reason the magnitude of the friction and the acceleration pressure drop in the entire riser is studied in small-scale risers. Two series of studies were performed: the first one in a scaled cold model riser of the 10 kW_th facility, and the second one in the 10 kW_th fluidized bed riser under process conditions. The velocities were chosen to comply with the fluidization regimes suitable for the calcium looping process, namely, the turbulent and the fast. In cold-model experiments in a low-velocity turbulent fluidization regime, the actual weight (static pressure drop) of the particles is observed more than the weight calculated from a recorded pressure drop. This phenomenon is also repeated in pilot plant conditions. In the cold-model setup, the friction and acceleration pressure drop became apparent in the fast fluidization regime, and increased as the gas velocity rose. Within calcium looping conditions in the pilot plant operation, the static pressure drop was observed more than the recorded pressure drop. Therefore, as a conservative approach, the influence of friction pressure drop may be neglected while calculating the solid inventory of the riser. The concept of transit inventory is introduced as a fraction of total inventory, which lies in freefall zones of the CFB system. This fraction increases as gas velocity rises.     

High-density circulating fluidized bed gasifier for advanced IGCC/IGFC—Advantages and challenges

Coal-fired Integrated Gasification Combined Cycle （IGCC） and Integrated coal Gasification Fuel-cell Com- bined cycle （IGFC） are being developed as high-efficiency electric power generation technology. However, the highest theoretical gross thermal efficiency of the conventional IGCC]IGFC is still below 52~. In order to obtain higher power generation efficiency, an advanced IGCC （A-IGCC） or advanced IGFC （A-IGFC） sys- tem making use of the exergy recuperation concept by recycling waste heat from gas turbine or fuel cells for steam gasification of coal and biomass was proposed in our laboratory, Corresponding to this system, a novel high-density triple-bed combined circulating fluidized bed （TBCFB） gasifier, composed of a downer pyrolyzer, a bubbling fluidized bed char gasifier, and a riser combustor, was proposed to replace traditional gasifiers such as the entrained flow bed gasifier. The new system is expected to more effectively utilize the waste heat from gas turbines or fuel cells and the heat produced by the combustion of the unreacted char in the riser combustor for pyrolysis and gasification of coal and biomass. In this short review, the advantages and future challenges in the development of high-density TBCFB gasifier are presented and discussed.