Turbulent Heat Transfer and Large Coherent Structures in Trailing-edge Cutback Film Cooling

Film cooling is a key technology for improving the thermal efficiency and power output of gas turbines. The trailing-edge section of high-pressure turbine blades can be efficiently cooled by ejecting a film over a cutback on the pressure side of the blade. In this paper, results of Large–Eddy Simulations (LES) are presented that match an existing experimental setup. Altogether, eight simulations with the blowing ratio M varying as the only parameter were performed over a range from M?=?0.35 to 1.4. Reasonably good agreement between LES and experiments were obtained for flow field statistics and adiabatic film-cooling effectiveness η _aw. Within a limited range of blowing ratios, an increase in the blowing ratio results in a counter-intuitive decrease of the cooling effectiveness. The present work suggests a mechanism that can explain this behavior. The visualization and analysis of large coherent structures showed that there exists dominant clockwise-rotating structures that can give rise to a combined upstream- and wall-directed turbulent heat flux. This turbulent heat flux represents the main contribution of the total heat flux and causes a significantly intensified thermal mixing process, which in turn results in the counter-intuitive decrease of the cooling effectiveness.     

Joint RANS/LES Approach to Premixed Flame Modelling in the Context of the TFC Combustion Model

We present an original timesaving joint RANS/LES approach to simulate turbulent premixed combustion. It is intended mainly for industrial applications where LES may not be practical. It is based on successive RANS/LES numerical modelling, where turbulent characteristics determined from RANS simulations are used in LES equations for estimation of the subgrid chemical source and viscosity. This approach has been developed using our TFC premixed combustion model, which is based on a generalization of the Kolmogorov’s ideas. We assume existence of small-scale statistically equilibrium structures not only of turbulence but also of the reaction zones. At the same time, non-equilibrium large-scale structures of reaction sheets and turbulent eddies are described statistically by model combustion and turbulence equations in RANS simulations or follow directly without modelling in LES. Assumption of small-scale equilibrium gives an opportunity to express the mean combustion rate (controlled by small-scale coupling of turbulence and chemistry) in the RANS and LES sub-problems in terms of integral or subgrid parameters of turbulence and the chemical time, i.e. the definition of the reaction rate is similar to that of the mean dissipation rate in turbulence models where it is expressed in terms of integral or subgrid turbulent parameters. Our approach therefore renders compatible the combustion and turbulent parts of the RANS and LES sub-problems and yields reasonable agreement between the RANS and averaged LES results. Combining RANS simulations of averaged fields with LES method (and especially coupled and acoustic codes) for simulation of corresponding nonstationary process (and unsteady combustion regimes) is a promising strategy for industrial applications. In this work we present results of simulations carried out employing the joint RANS/LES approach for three examples: High velocity premixed combustion in a channel, combustion in the shear flow behind an obstacle and the impinging flame (a premixed flame attached to an obstacle).     

Film cooling and heat transfer with air injection through two rows of compound angle holes.

This paper describes the results of an experimental investigation into the film cooling effectiveness and the heat transfer characteristics of two staggered rows of compound angle holes. The effects of hole spacings and turbulence intensity on film cooling and heat transfer characteristic are investigated for three blowing rates; 0.5, 1.0 and 1.7. An attempt has been made to correlate the film cooling effectiveness results using a two dimensional correlation group. The increase of spanwise hole spacing results in a reduction in the film cooling effectiveness and an increase in the Stanton number. Increasing the freestream turbulence intensity has caused a significant reduction in the local film cooling effectiveness but increased the Stanton number, especially at blowing rate of 0.5.     

DNS,LES and RANS of turbulent heat transfer in boundary layer with suddenly changing wall thermal conditions

The objectives of this study are to investigate a thermal field in a turbulent boundary layer with suddenly changing wall thermal conditions by means of direct numerical simulation (DNS), and to evaluate predictions of a turbulence model in such a thermal field, in which DNS of spatially developing boundary layers with heat transfer can be conducted using the generation of turbulent inflow data as a method. In this study, two types of wall thermal condition are investigated using DNS and predicted by large eddy simulation (LES) and Reynolds-averaged Navier–Stokes equation simulation (RANS). In the first case, the velocity boundary layer only develops in the entrance of simulation, and the flat plate is heated from the halfway point, i.e., the adiabatic wall condition is adopted in the entrance, and the entrance region of thermal field in turbulence is simulated. Then, the thermal boundary layer develops along a constant temperature wall followed by adiabatic wall. In the second case, velocity and thermal boundary layers simultaneously develop, and the wall thermal condition is changed from a constant temperature to an adiabatic wall in the downstream region. DNS results clearly show the statistics and structure of turbulent heat transfer in a constant temperature wall followed by an adiabatic wall. In the first case, the entrance region of thermal field in turbulence can be also observed. Thus, both the development and the entrance regions in thermal fields can be explored, and the effects upstream of the thermal field on the adiabatic region are investigated. On the other hand, evaluations of predictions by LES and RANS are conducted using DNS results. The predictions of both LES and RANS almost agree with the DNS results in both cases, but the predicted temperature variances near the wall by RANS give different results as compared with DNS. This is because the dissipation rate of temperature variance is difficult to predict by the present RANS, which is found by the evaluation using DNS results.     

细颗粒泥沙净冲刷和输移的大涡模拟研究

在传统水沙输移数值模拟研究中一般采用雷诺时均模拟技术(Reynolds-averaged simulation,RANS).与RANS相比,大涡模拟技术(large eddy simulation,LES)能够更加精确反映细部流动结构,计算机的发展使得采用LES探讨水流和泥沙运动规律成为可能.本文尝试给出净冲刷条件下悬沙计算的边界条件,采用动态亚格子模式对循环槽道和长槽道中的水流运动和泥沙输移进行了三维大涡模拟研究.利用直接数值模拟(direct numerical simulation,DNS)结果对LES模型进行了率定,计算结果符合良好,在此基础上初步探讨了泥沙浓度、湍动强度和湍动通量等的分布特征.结果表明,净冲刷条件下输沙平衡时泥沙浓度符合Rouse公式分布,单向流动中泥沙浓度沿着流向逐渐增大.泥沙浓度湍动强度和湍动通量都在近底部达到最大值,沿着垂向迅速减小.湍动黏性系数和扩散系数基本上在水深中间处达到最大.湍动Schmidt数沿着水深方向不是常数,在近底部和自由水面附近较大,在水深中间处较小.     

Hybrid RANS/LES of flow and heat transfer in round impinging jets

Fluid flow and convective heat transfer predictions are presented of round impinging jets for several combinations of nozzle-plate distances H/D = 2, 6 and 13.5 (where D is the nozzle diameter) and Reynolds numbers Re = 5000, 23,000 and 70,000 with the newest version of the k-ω model of Wilcox (2008) and three hybrid RANS/LES models. In the RANS mode of the hybrid RANS/LES models, the k-ω model is recovered. Three formulations are considered to activate the LES mode. The first model is similar to the hybrid models of Davidson and Peng (2003) and Kok et al. (2004). The turbulent length scale is replaced by the grid size in the destruction term of the k-equation and in the definition of the RANS eddy viscosity. As grid size, a maximum measure of the hexahedral grid cell is used. The second model has the same k-equation, but the eddy viscosity is the minimum of the k-ω eddy viscosity and the Smagorinsky eddy viscosity, following a proposal by Batten et al. (2004). The Smagorinsky eddy viscosity is formed with the cube root of the cell volume. The third model has, again, the same k-equation, but has an eddy viscosity which is an intermediate between the eddy viscosities of the first and second models. This is reached by using the cube root of the cell volume in the eddy viscosity formula of the first model.The simulation results are compared with experimental data for the high Reynolds number cases Re = 23,000 and Re = 70,000 and LES data for the low-Reynolds number case Re = 5000. The Reynolds numbers are defined with the nozzle diameter and the bulk velocity at nozzle outlet. At low nozzle-plate distance (the impingement plate is in the core of the jet), turbulent kinetic energy is overpredicted by RANS in the stagnation flow region. This leads to overprediction of the heat transfer rate along the impingement plate in the impact zone. At high nozzle-plate distance (the impingement plate is in the mixed-out region of the jet), the turbulence mixing is underpredicted by RANS in the shear layer of the jet which gives a too high length of the jet core. This also results in overprediction of the heat transfer rate in the impingement zone caused by too big temperature gradients at impingement.All hybrid RANS/LES models are able to correct the heat transfer overprediction of the RANS model. For good predictions at low nozzle-plate distance, it is necessary to sufficiently resolve the formation and development of the near-wall vortices in the jet impingement region. At high nozzle-plate distance, the essence is to capture the evolution and breakup of the flow unsteadiness in the shear layer of the jet, so that accurate mean and fluctuating velocity profiles are obtained in the impingement region. Although the models have a quite different theoretical justification and generate a quite different eddy viscosity in some flow regions, their overall results are very comparable. The reason is that in zones that are crucial for the results, the models behave similarly.     

Numerical study of an oscillatory turbulent flow over a flat plate

Oscillatory turbulent flow over a flat plate is studied using large eddy simulation (LES) and Reynolds-average Navier-Stokes (RANS) methods. A dynamic subgrid-scale model is employed in LES and Saffman's turbulence model is used in RANS. The flow behaviors are discussed for the accelerating and decelerating phases during the oscillating cycle. The friction force on the wall and its phase shift from laminar to turbulent regime are also investigated for different Reynolds numbers. The project supported by the Youngster Funding of Academia Sinica and by the National Natural Science Foundation of China     

Towards a Unified Turbulence Simulation Approach for Wall-Bounded Flows

A hybrid Reynolds-averaged Navier–Stokes/Large-Eddy Simulation (RANS/LES) methodology has received considerable attention in recent years, especially in its application to wall-bounded flows at high-Reynolds numbers. In the conventional zonal hybrid approach, eddy-viscosity-type RANS and subgrid scale models are applied in the RANS and LES zones, respectively. In contrast, the non-zonal hybrid approach uses only a generalized turbulence model, which provides a unified simulation approach that spans the continuous spectrum of modeling/simulation schemes from RANS to LES. A particular realization of the non-zonal approach, known as partially resolved numerical simulation (PRNS), uses a generalized turbulence model obtained from a rescaling of a conventional RANS model through the introduction of a resolution control function F _R , where F _R is used to characterize the degree of modeling required to represent the unresolved scales of turbulent motion. A new generalized functional form for F _R in PRNS is proposed in this study, and its performance is compared with unsteady RANS (URANS) and LES computations for attached and separated wall-bounded turbulent flows. It is demonstrated that PRNS behaves similarly to LES, but outperforms URANS in general.     

An investigation of thermally stratified turbulent channel flow with temperature oscillation on the bottom wall by large eddy simulation

Thermally stratified shear turbulent channel flow with temperature oscillation on the bottom wall of the channel is calculated to investigate the behavior of turbulent flow and heat transfer by use of large eddy simulation (LES) approach coupled with dynamic subgrid-scale (SGS) models. The objective of this study is to deal with the effect of the temperature oscillation on turbulent behavior of thermally stratified turbulent channel flow and to examine the effectiveness of the LES technique for predicting statistically unsteady turbulent flow driven by time-varying buoyancy force. To validate the present calculation, thermally stratified shear turbulent channel flow is computed and compared with available data obtained by direct numerical simulation (DNS), which confirm that the present approach can be used to predict thermally stratified turbulent channel flow satisfactorily. Further, to illustrate the effect of the temperature oscillation with different Richardson numbers and periods of the oscillation on turbulence characteristics, the phase-averaged mean value and fluctuation of the resolved velocities and temperature, and instantaneous velocity fluctuation structures are analyzed.     

Reynolds averaged simulation of flow and heat transfer in ribbed ducts

The accuracy of modern eddy-viscosity type turbulence models in predicting turbulent flows and heat transfer in complex passages is investigated. The particular geometries of interest here are those related to turbine blade cooling systems. This paper presents numerical data from the calculation of the turbulent flow field and heat transfer in two-dimensional (2D) cavities and three-dimensional (3D) ribbed ducts. It is found that heat transfer predictions obtained using the v²–f turbulence model for the 2D cavity are in good agreement with experimental data. However, there is only fair agreement with experimental data for the 3D ribbed duct. On the wall of the duct where ribs exist, predicted heat transfer agrees well with experimental data for all configurations (different streamwise rib spacing and the cavity depth) considered in this paper. But heat transfer predictions on the smooth-side wall do not concur with the experimental data. Evidence is provided that this is mainly due to the presence of strong secondary flow structures which might not be properly simulated with turbulence models based on eddy viscosity.     

Highly Resolved LES and URANS of Turbulent Buoyancy-Driven Flow Within Inclined Differentially-Heated Enclosures

In the present study, both LES and unsteady RANS computations are presented, for turbulent natural convection of air inside differentially-heated rectangular tilted cavities using a finite volume code (Code_Saturne), for an aspect ratio of H/L?=?28.6 and Rayleigh number of 0.86×10⁶. Attention is focused on two angles of inclination: 15° to the horizontal with hot lower and cold upper wall, the 15° unstable case, and the mirror image of this case where the angle is the same but with a hot upper and cold lower wall, the 15° stable case. In accordance with recent experimental data, the LES computations for both the stable and unstable tilted cavities returned three-dimensional time-averaged flow fields. In the case of the unstably stratified enclosure, the flow is highly unsteady with coherent turbulent structures in the core of the enclosure. Time-averaged temperature, velocity and resolved turbulence intensities resulting from LES computations show close agreement to measured data. Subsequent comparisons of different URANS schemes with LES are used in order to explore to what extent these models are able to reproduce the large-scale unsteady flow structures. All URANS schemes have been found to be able to reproduce the 3-D unsteady flow features present in the 15° unstable cavity. However, the low-Reynolds-number model tested, as well as requiring a high resolution near-wall grid, also needed a finer grid in the core region than the high-Reynolds-number models, thus making it computationally very expensive. Flow within the 15° stable cavity also shows some 3-D features, although it is significantly less unsteady, and the URANS models tested here have been less successful in reproducing this flow pattern. The overall heat transfer is presented here for both differentially heated enclosures.     

Hybrid RANS/LES computations of plane impinging jets with DES and PANS models

The qualities of a DES (Detached Eddy Simulation) and a PANS (Partially-Averaged Navier–Stokes) hybrid RANS/LES model, both based on the k–ω RANS turbulence model of Wilcox (2008, “Formulation of the k–ω turbulence model revisited” AIAA J., 46: 2823–2838), are analysed for simulation of plane impinging jets at a high nozzle-plate distance (H/B = 10, Re = 13,500; H is nozzle-plate distance, B is slot width; Reynolds number based on slot width and maximum velocity at nozzle exit) and a low nozzle-plate distance (H/B = 4, Re = 20,000). The mean velocity field, fluctuating velocity components, Reynolds stresses and skin friction at the impingement plate are compared with experimental data and LES (Large Eddy Simulation) results. The k–ω DES model is a double substitution type, following Davidson and Peng (2003, “Hybrid LES–RANS modelling: a one-equation SGS model combined with a k–ω model for predicting recirculating flows” Int. J. Numer. Meth. Fluids, 43: 1003–1018). This means that the turbulent length scale is replaced by the grid size in the destruction term of the k-equation and in the eddy viscosity formula. The k–ω PANS model is derived following Girimaji (2006, “Partially-Averaged Navier–Stokes model for turbulence: a Reynolds-Averaged Navier–Stokes to Direct Numerical Simulation bridging method” J. Appl. Mech., 73: 413–421). The turbulent length scale in the PANS model is constructed from the total turbulent kinetic energy and the sub-filter dissipation rate. Both hybrid models change between RANS (Reynolds-Averaged Navier–Stokes) and LES based on the cube root of the cell volume. The hybrid techniques, in contrast to RANS, are able to reproduce the turbulent flow dynamics in the shear layers of the impacting jet. The change from RANS to LES is much slower however for the PANS model than for the DES model on fine enough grids. This delays the break-up process of the vortices generated in the shear layers with as a consequence that the DES model produces better results than the PANS model.     

Large eddy simulation of fuel injection and mixing process in a diesel engine

The large eddy simulation(LES) approach implemented in the KIVA-3V code and based on one-equation sub-grid turbulent kinetic energy model are employed for numerical computation of diesel sprays in a constant volume vessel and in a Caterpillar 3400 series diesel engine.Computational results are compared with those obtained by an RANS(RNG k-ε) model as well as with experimental data.The sensitivity of the LES results to mesh resolution is also discussed.The results show that LES generally provides flow and spray characteristics in better agreement with experimental data than RANS;and that small-scale random vortical structures of the in-cylinder turbulent spray field can be captured by LES.Furthermore,the penetrations of fuel droplets and vapors calculated by LES are larger than the RANS result,and the sub-grid turbulent kinetic energy and sub-grid turbulent viscosity provided by the LES model are evidently less than those calculated by the RANS model.Finally,it is found that the initial swirl significantly affects the spray penetration and the distribution of fuel vapor within the combustion chamber.     

An Attempt to Combine Large Eddy Simulation with the k-ε Model in a Channel-Flow Calculation

Large eddy simulation (LES) is combined with the Reynolds-averaged Navier–Stokes (RANS) equation in a turbulent channel-flow calculation. A one-equation subgrid-scale model is solved in a three-dimensional grid in the near-wall region whereas the standard k–ε model is solved in a one-dimensional grid in the outer region away from the wall. The two grid systems are overlapped to connect the two models smoothly. A turbulent channel flow is calculated at Reynolds numbers higher than typical LES and several statistical quantities are examined. The mean velocity profile is in good agreement with the logarithmic law. The profile of the turbulent kinetic energy in the near-wall region is smoothly connected with that of the turbulent energy for the k–ε model in the outer region. Turbulence statistics show that the solution in the near-wall region is as accurate as a usual LES. The present approach is different from wall modeling in LES that uses a RANS model near the wall. The former is not as efficient as the latter for calculating high-Reynolds-number flows. Nevertheless, the present method of combining the two models is expected to pave the way for constructing a unified turbulence model that is useful for many purposes including wall modeling. Received 11 June 1999 and accepted 15 December 2000     

A Rapid and Accurate Switch from RANS to LES in Boundary Layers Using an Overlap Region

An efficient recycling algorithm is developed for injecting resolved turbulent content in a boundary layer as it switches from a Reynolds Averaged Navier-Stokes (RANS) type treatment to a Large Eddy Simulation (LES) type treatment inside a generalized Detached-Eddy Simulation (DES). The motivation is to use RANS in the thinnest boundary-layer area, following the original argument in favour of DES, and LES in the thicker boundary-layer areas especially approaching separation, to improve accuracy and possibly obtain unsteady outputs. The algorithm relies on an overlap of the RANS and LES domains and, therefore, the availability of both RANS and LES solutions in the recycling region, which is about 5 boundary-layer thicknesses long. This permits a smooth transfer of the turbulent stresses from this section to the LES inflow. The continuity of the skin-friction distribution is very good, reflecting the excellent viability of the resolved turbulence. The approach is validated in a flat-plate boundary layer and an airfoil near stall, with mild pressure gradient near the interface, and then applied to the compressible flow over an idealized airliner windshield wiper. The pressure fluctuations at reattachment are 12dB more intense than under a simple boundary layer at the same speed, and the output contains all the quantities needed to calculate the transmission of sound through the glass.     

湍流边界层拟序结构的实验研究

20世纪60年代后, 先后从流动显示发现了快慢斑、猝发、上升流、下扫流和多种涡结构等湍流边界层的拟序结构. 它们对湍流边界层的摩阻、传热传质和湍动能的产生等特性有重要影响. 涡结构是上述拟序结构的核心, 它影响其它拟序结构的发展和演变. 发卡涡通常被认为是基本涡结构. 发卡涡等涡结构的再生, 是湍流边界层拟序结构能够自持续的必要的因素.壁面低速流上升产生猝发, 是湍流边界层湍能的主要来源; 条件采样是测量猝发频率和其它拟序结构出现频率的重要手段. 流动显示对湍流边界层拟序结构作了大量定性观察, 有许多减阻和增加传热率等应用性研究在此基础上发展起来. 80年代后, 出现了测量湍流边界层的瞬时流速矢量场的多热线法和PIV技术, 三维PIV技术可望将来为湍流边界层的实验研究带来重大进展. 本文评述了流动显示法、多热线法和PIV技术的优点和不足之处, 以及它们在对湍流边界层拟序结构的研究中的贡献.      

Large Eddy and Reynolds-Averaged Navier - Stokes Simulations of Turbulent Flow Over an Airfoil

A Large Eddy Simulation (LES) of turbulent flow over an airfoil near stall is performed. Results of the LES are compared with those of Reynolds-Averaged Navier-Stokes (RANS) simulations using two well-known turbulence models, namely the Baldwin-Lomax model and the Spalart-Allmaras model. The subgrid scale model used for the LES is the filtered structure function model. All simulations are performed using the same structured multi-block code. In order to reduce the CPU time, an implicit time stepping method is used for the LES. The purpose of this study is to show the possibilities and limitations of LES of complex flows associated with aeronautical applications using state of the art simulation techniques. Typical flow features are captured by the LES such as the adverse-pressure gradient and flow retardation. Visualization of instantaneous flow fields shows the typical streaky structures in the near-wall region.     

Simulation of wing-body junction flows with hybrid RANS/LES methods

In this paper, flows past two wing-body junctions, the Rood at zero angle of attack and NASA TN D-712 at 12.5° angle of attack, are investigated with two Reynolds-Averaged Navier-Stokes (RANS) and large eddy simulation (LES) hybrid methods. One is detached eddy simulation (DES) and the other is delayed-DES, both are based on a weakly nonlinear two-equation k–ω model. While the RANS method can predict the mean flow behaviours reasonably accurately, its performance for the turbulent kinetic energy and shear stress, as compared with available experimental data, is not satisfactory. DES, through introducing a length scale in the dissipation terms of the turbulent kinetic energy equation, delivers flow separation, a vortex or the onset of vortex breakdown too early. DDES, with its delayed effect, shows a great improvement in flow structures and turbulence characteristics, and agrees well with measurements.     

Implementation and Evaluation of an Embedded LES-RANS Solver

In the current work, we present the development and application of an embedded large-eddy simulation (LES) - Reynolds-averaged Navier Stokes (RANS) solver. The novelty of the present work lies in fully embedding the LES region inside a global RANS region through an explicit coupling at the arbitrary mesh interfaces, exchanging flow and turbulence quantities. In particular, a digital filter method (DFM) extracting mean flow, turbulent kinetic energy and Reynolds stress profiles from the RANS region is used to provide meaningful turbulent fluctuations to the LES region. The framework is developed in the open-source computational fluid dynamics software OpenFOAM. The embedding approach is developed and validated by simulating a spatially developing turbulent channel flow. Thereafter, flow over a surface mounted spanwise-periodic vertical fence is simulated to demonstrate the importance of the DFM and the effect of the location of the RANS-LES interface. Mean and second-order statistics are compared with direct numerical simulation (DNS) data from the literature. Results indicate that feeding synthetic turbulence at the LES interface is essential to achieve good agreement for the mean flow quantities. However, in order to obtain a good match for the Reynolds stresses, the LES interface needs to be placed sufficiently far upstream, which in the present case was six spoiler heights before the fence. Further, a realistic spoiler configuration with finite-width in the spanwise direction and inclined at 30 degrees was simulated using the embedding approach. As opposed to the vertical fence case this is a genuinely (statistically) three-dimensional case and a very good match with mean and second-order statistics was obtained with the experimental data. Finally, in order to test the present solver for high sub-sonic speed flows the flow over an open cavity was simulated. A good match with reference data is obtained for mean and turbulence profile comparisons. Tones in the pressure spectra were predicted reasonably well and an overall sound pressure level with a maximum deviation of 2.6 d B was obtained with the present solver when compared with the experimental data.