正方形排列四圆柱体绕流特性及互扰效应研究

基于计算流体动力学理论,运用大涡模拟方法对雷诺数Re=3900三维正方形排列四圆柱体结构群的绕流问题进行数值计算,主要分析来流攻角与间距比两个参数对四圆柱体结构群流体参数及流场模态的影响。结果表明:来流攻角与间距比均对四圆柱体结构群绕流特性有较强的影响;来流攻角θ=0°、22.5°、45°下,临界间距比分别为3.5、4.0、3.0;间距比的变化会导致下游圆柱表面压力系数分布发生改变;另一方面,间距比较小时,四圆柱体结构之间的互扰作用均以临近效应为主;随间距比增大,上游圆柱尾流对下游圆柱有显著影响,其互扰作用会转变尾激效应。     

串列布置三圆柱涡激振动频谱特性研究

对串列三圆柱体双自由度涡激振动问题进行了数值计算, 并分析了雷诺数、固有频率比和约化速度对串列三圆柱体结构动力响应及频谱特性的影响. 研究发现: 雷诺数、频率比对上游圆柱的振幅和流体力系数的影响较小. 中游圆柱频率锁定区域随着雷诺数的增大而增大, 其动力响应受上游圆柱尾流的影响较大, 但频率比的影响较小. 同时, 流体力系数在约化速度较小时受雷诺数和频率比的影响较大. 另外, 下游圆柱的振幅和流体力系数受雷诺数及频率比的影响较大. 雷诺数、频率比和约化速度对圆柱流体力系数能量谱密度(PSD)曲线中主峰幅值、频谱成分及波动性的影响较大. 流体力系数PSD曲线波动性的增强, 导致圆柱运动轨迹会从"8"字形转变成不规则形状. 当频率比为2.0时, 上游圆柱尾流出现P$+$S模式, 导致其发生非对称运动, 且升、阻力系数PSD曲线主峰重合. 最后, 激励荷载平均功率值随约化速度的变化趋势与对应的结构动力响应的变化类似. 在同一约化速度区间内, 结构振动响应的强弱与位移的平均功率值成正比. 对不同约化速度区间内的升力系数功率谱密度分析时, 振动频率比($f_{s}/f_{n, y})$对结构振动响应的影响更大.      

均匀旋转对圆柱水动力及流动结构的影响

基于格子Boltzmann方法 (LBM)对均匀旋转控制下的低雷诺数(Re=100)圆柱绕流问题进行了数值模拟,得到了转速比从0～10变化下,旋转控制对圆柱水动力及流动结构的影响规律.使用动态模态分解(DMD)对流场特征进行提取,并分析了施加旋转控制之后转速比对流场不同模态和增长率的影响.结果表明,随着转速比增大,圆柱下游流动结构依次呈现出卡门涡街、剪切层、反向剪切层、单侧涡和附着涡5种结构;阻力系数时均值先减小,随后在转速进入单侧涡区间后增大,升力系数与力矩系数的时均值均单调增加,同时,在出现涡脱落的两个转速区间内,水动力出现了明显的波动,且二次失稳时波动幅度更大. DMD的结果表明,圆柱下游的流动结构主要受圆柱壁面的旋转影响而发生改变并产生全新流动模态;旋转会对流动稳定性产生影响:在未充分发展阶段,旋转对流动稳定性的影响不显著,而在充分发展后,各转速下的流场不稳定模态数均远少于未充分发展阶段,随着转速比的增大,流动稳定性会产生不同程度的增强或减弱,且无涡脱落时的稳定性高于有涡脱落时,因此,通过旋转控制抑制尾涡脱落可以有效增强流动的稳定性.     

旋转圆柱绕流流场特性分析

对雷诺数Re = 20000 ~ 90000、相对转速ɑ = 0 ~ 0.72的旋转圆柱后方流场进行了实验测量, 分析了旋转圆柱后方不同剖面处的速度分布规律和湍流度分布规律. 采用LES方法对旋转圆柱绕流问题进行了数值模拟, 分析旋转圆柱周围流场特性和自由剪切层变化规律, 最后通过理论模型对流场变化进行分析, 得出如下结论: 当圆柱逆时针旋转时, 同一雷诺数下随着相对转速的增加, 旋转圆柱尾迹区域下方速度突变处的位置随着相对转速的增加而上移, 而上方速度突变处的位置不变, 雷诺数的增加使旋转圆柱尾迹区域下方速度突变处位置有小幅度的下移. 通过数值模拟发现, 圆柱旋转之后, 圆柱后方下侧涡的位置明显上移, 且幅度较大. 下方的自由剪切层有明显的上移, 上方的自由剪切层位置变化较小. 最后通过理论分析发现, 圆柱后侧下方涡位置的上移对圆柱升力影响十分显著, 在高雷诺数、低相对转速的条件下, 旋转圆柱后侧下方涡位置的改变对旋转圆柱的升力、尾流区自由剪切层的变化起到了重要的影响.      

幂律流体圆柱绕流的格子波尔兹曼模拟

基于插值补充格子波尔兹曼方法和幂律流体的本构方程,建立了贴体坐标系下适用于幂律流体的格子波尔兹曼模型,模拟了幂律流体的圆柱绕流问题,采用非平衡外推格式处理圆柱表面的速度无滑移边界,利用应力积分法确定曳力系数和升力系数,并与基于标准的格子波尔兹曼方法和有限容积法获得的数值数据进行对比,吻合良好. 进行了网格无关性验证之后,分析了稳态流动时,不同雷诺数下幂律指数对于尾迹长度、分离角、圆柱表面黏度分布、表面压力系数及曳力系数的影响,以及非定常流动中,幂律指数对于流场、曳力系数、升力系数和斯特劳哈尔数的影响. 获得的变化规律与基于其他数值模拟方法得到的结果相一致,充分验证了模型的有效性和正确性. 结果表明:插值补充格子波尔兹曼方法可以用来模拟幂律流体在具有复杂边界流场内的流动问题,通过引入不同的非牛顿流体本构方程,该方法还可以进一步应用于其他类型的非牛顿流体研究中.      

绕旋转圆柱流动涡尾流结构和临界状态特性

采用作者提出的基于区域分解，有限差分法与涡法杂交的数值方法，结合高阶隐式差分格式，和以修正的不完全ＬＵ分解为预处理器的共轭梯度法作求解器，系统地研究了雷诺数Ｒｅ＝１０００，旋转速度比α∈（０．５，３．２５）范围内，绕旋转圆柱从突然起到充分发展，长时间内尾流旋涡结构和阻力，升力系数的变化规律，计算所得流动图案与实验流场显示符合很好。数值试验证帝了临界状态的存在，并首次给出了临界状态时的旋涡结构特性。     

双圆柱斜置排列时下游圆柱压力分布和振荡频率的实验研究

当两个圆柱斜置排列并靠得较近时,绕流下游圆柱的流动明显地不同于单一圆柱.本文研究了下游圆柱压力分布受到的影响,并着重于用FFT来分析圆柱表面某些特征点上的压力频谱,研究频谱与圆柱之间的相对距离和位置的关系.当圆柱间距较远时,压力振荡的频率与单圆柱卡门涡节的频率相接近,随着横向间距的接近,频率逐渐降低,然而当两圆柱十分接近时,外侧压力振荡的频率继续降低,但圆柱内侧压力振荡的频率却突然提高,出现了一个圆柱体两侧作用有不同频率压力的情况.     

串列双圆柱绕流问题的数值模拟

本文运用有限体积方法,对绕串列放置的双圆柱的二维不可压缩流动进行了数值计算。为研究两圆柱不同间距对圆柱相互作用和尾流特征的影响,选取间距比Ｌ／Ｄ（Ｌ为两圆柱中心间的距离,Ｄ为圆柱直径）在１．５～５．０之间每隔０．５共八个有代表性的间距进行了计算模拟。计算均在Ｒｅ＝２００条件下进行。计算结果表明：对该绕流问题,流动特征在很大程度上取决于间距的大小。且间距存在一临界值,间距比从小于临界值变化到大于临界     

基于定常吹吸气的波浪型圆柱主动控制研究

基于定常吹吸气对波浪型圆柱近尾迹流动进行控制以增强柱体振动, 采用大涡模拟研究了亚临界雷诺数(Re = 3000)下前吹后吸和前后吸气控制方式在不同吹吸气工况对波浪型圆柱升阻力特性、时均压力系数、环量、湍动能及近尾迹流动结构的影响. 研究发现: 前吹后吸和前后吸气控制下波浪型圆柱在不同吹吸气动量系数工况脉动升力系数均显著提高, 最大较未受控直圆柱和波浪型圆柱分别提升高达636%和391%, 这主要可能归因于吹吸气控制使波浪型圆柱回流区变短, 高强度涡集中向钝体后方靠拢, 旋涡形成长度缩短, 展向涡流与顺流向涡流相互作用在波浪型圆柱下游形成的“肋状涡”变大变长, 近尾迹环量显著增大, 从而导致脉动升力系数增大, 这可能将诱导柱体产生更强的振动; 同时两种控制方式均改变了波浪型圆柱表面的压力分布, 由于在波浪型圆柱前驻点吹气使前端趋于流线型, 前吹后吸在不同吹吸气动量系数下波浪型圆柱的高压区减小, 但在后驻点吸气使得低压区增大, 而前后吸气在不同吹吸气动量系数下波浪型圆柱的高压区基本不变, 低压区增大. 研究结果可为低风速地区分布式风力俘能结构俘能效率提升提供基础理论支持.      

串列双圆柱体绕流特性与互扰效应研究

基于大涡模拟(LES)方法对亚临界雷诺数(Re=3900)下三维串列双圆柱体绕流问题进行了数值计算。首先,通过求解单圆柱算例来验证计算模型及参数的正确性。然后,着重分析了不同间距比对双圆柱体的流体力系数的影响,并阐述了双圆柱体流场特性变化及其互扰效应内在机理。研究表明:雷诺数Re=3900时,串列双圆柱体绕流临界间距比在3.9～4.0之间;随着间距比的增加,双圆柱体临近流场中二次涡团形成的区域与三维涡结构均会发生变化,导致其结构表面所受的流体力系数在时间与空间上变化的规律性逐渐减弱;达到临界间距比时,流体力系数的变化会呈现出较强的规律性。     

The effects of surface injection through a perforated square cylinder on some aerodynamic parameters

The surface pressure distribution and the vortex shedding frequency were investigated for the flow around perforated horizontal and diagonal square cylinders with surface injection through various surfaces. For this purpose, surface pressure measurements on each square cylinder (horizontal and diagonal) and vortex shedding frequency measurements in the wake region were performed at three different Reynolds numbers in a wind tunnel. The parameters considered were injection coefficient, position of perforated surface (i.e., top, rear, top-rear and all), pressure coefficient, drag coefficient, and the Strouhal number. The results showed that pressure coefficient distribution, drag coefficient, and the Strouhal number were influenced by the position of the perforated surface and by the injection coefficient. The surface injections through the top-rear, rear and all surfaces of a diagonal square cylinder reduce the drag coefficient for the all Reynolds numbers, while the injection through all surfaces only reduces the drag coefficient of a horizontal square cylinder. The other aerodynamic parameter Strouhal number can also be controlled by injection through certain surfaces of a horizontal square cylinder.     

带有柔性薄板三维方柱流固耦合的数值模拟研究

采用双向流固耦合方法,对带有柔性薄板三维方柱的流场变化特性进行了研究。通过对比单方柱,分析了带有柔性薄板三维方柱阻力系数、升力系数以及斯特劳哈尔数的变化规律。研究表明,在方柱尾流区域附加一柔性薄板可以使其阻力系数降低34.6%,同时其变化幅值大大减小;其升力系数的均方根减小84.8%,流场脉动大幅度减小;斯特劳哈尔数降低79.5%。研究结果表明,在三维方柱后设置柔性薄板可有效抑制涡脱落,从而改善三维方柱的尾流特性。     

Vortex shedding from a square cylinder in presence of a moving wall

A numerical study on the flow past a square cylinder placed parallel to a wall, which is moving at the speed of the far field has been made. Flow has been investigated in the laminar Reynolds number (based on the cylinder length) range. We have studied the flow field for different values of the cylinder to wall separation length. The governing unsteady Navier–Stokes equations are discretized through the finite volume method on a staggered grid system. A SIMPLE type of algorithm has been used to compute the discretized equations iteratively. A shear layer of negative vortex generates along the surface of the wall, which influences the vortex shedding behind the cylinder. The flow‐field is distinct from the flow in presence of a stationary wall. An alternate vortex shedding occurs for all values of gap height in the unsteady regime of the flow. The strong positive vortex pushes the negative vortex upwards in the wake. The gap flow in the undersurface of the cylinder is strong and the velocity profile overshoots. The cylinder experiences a downward force for certain values of the Reynolds number and gap height. The drag and lift are higher at lower values of the Reynolds number. Copyright © 2005 John Wiley & Sons, Ltd.     

VORTEX SHEDDING RESONANCE FROM A ROTATIONALLY OSCILLATING CYLINDER

Vortex shedding resonance of a circular cylinder wake to a forced rotational oscillation has been investigated experimentally by measuring the velocity fluctuations in the wake, pressure distributions over the cylinder surface, and visualizing the flow field with respect to cylinder oscillations. The vortex shedding resonance occurs near the natural shedding frequency at small amplitude of cylinder oscillations, while the peak resonance frequency shifts to a lower value with an increase in oscillation amplitude. The drag and lift forces acting on the cylinder at fixed forcing Strouhal number indicate that the phase lag of fluid forces to the cylinder oscillations increases with an increase in oscillation amplitude, supporting the variation of resonance frequency with oscillation amplitude. The comparative study of the measured pressure distributions and the simultaneous flow visualizations with respect to cylinder rotation shows the mechanisms of phase lag, which is due to the strengthened vortex formation and the modification of the surface pressure distributions.     

Flow above the free end of a surface-mounted finite-height circular cylinder: A review

The wake of a surface-mounted finite-height circular cylinder and the associated vortex patterns are strongly dependent on the cylinder aspect ratio and the thickness of the boundary layer on the ground plane relative to the dimensions of the cylinder. Above a critical aspect ratio, the mean wake is characterized by streamwise tip vortex structures and Kármán vortex shedding from the sides of the cylinder. Below a critical aspect ratio, a unique mean wake structure is observed. Recent experimental studies in the literature that used phase-averaged techniques, as well as recent numerical simulations, have led to an improved physical understanding of the near-wake vortex flow patterns. However, the flow above the free end of the finite circular cylinder, and its relationship to the near wake, has not been systematically studied. The effects of aspect ratio and boundary layer thickness on the free-end flow field are also not completely understood, nor has the influence of Reynolds number on the free-end flow field been fully explored. Common features associated with the free end include separation from the leading edge, a mean recirculation zone containing a prominent cross-stream arch (or mushroom) vortex, and reattachment onto the free-surface. Other flow features that remain to be clarified include a separation bubble near the leading edge, one or two cross-stream vortices within this separation bubble, the origins of the streamwise tip or trailing vortices, and various critical points in the near-surface flow topology. This paper reviews the current understanding of the flow above the free end of a surface-mounted finite-height circular cylinder, with a focus on models of the flow field, surface oil flow visualization studies, pressure and heat flux distributions on the free-end surface, measurements of the local velocity field, and numerical simulations, found in the literature.     

Measurements of the flow over a low-aspect-ratio cylinder mounted on a ground plane

The flow over a finite-height cylinder of aspect ratio 1, with one end mounted on a ground plane and the other end free, has been studied by means of surface flow visualisation, particle image velocimetry (PIV) and surface pressure measurements. The diameter-based Reynolds number was 200,000. The mean flow topology has been identified in three areas: the horseshoe vortex system, the separated flow over the free-end and the wake region. Evidence is shown for the existence of a three-horseshoe vortex system, while the mean flow over the free-end consists of an arch vortex with its bases on the forward half of the free-end. There are two tip vortices coming off the free-end. The wake region is found to be highly unsteady, with considerable variation from the mean flow.     

Wake transition for surface mounted rectangular cylinder due to incoming shear flow

Three-dimensional unsteady wake characteristics have been investigated numerically in flow past surface mounted finite-height rectangular cylinder using Open Source Field Operation and Manipulation. Effect of impinging shear (shear intensity, K) on transitional characteristics of wake flow has been studied using iso-Q surfaces for Reynolds number (Re) in the range from 150 to 250. Various flow regimes, such as steady flow, symmetric and asymmetric modes of vortex shedding have been identified based on the values of Re and K for different side ratios (SR) of the cylinder. Unsteady wake oscillations have been analyzed using time signal of transverse velocity component in the wake. These signals have been decomposed into different component signals using Hilbert-Huang transformation (HHT). Variation of frequency and energy density with time of the decomposed signals has been presented in the form of Hilbert spectra. Effects of Re, SR and K on wake oscillation frequency have been illustrated in the form of marginal spectra. Time-delay reconstructions and Poincare sections have been examined to study periodic and aperiodic nature of the wake flow. Non-stationarity associated with the wake fluctuation is quantified in terms of degree of stationarity. Symmetric and asymmetric modes have been confirmed using singular value decomposition of the vorticity field and presented using dynamic modes. Growth rate and frequency of the modes corresponding to symmetric shedding are found to be lower than those for asymmetric shedding. In addition, variation in mean drag coefficient has been reported with change in Re and K for each value of SR.