On natural convection from a vertical plate with a prescribed surface heat flux in porous media

This paper presents a theoretical and numerical investigation of the natural convection boundary-layer along a vertical surface, which is embedded in a porous medium, when the surface heat flux varies as (1 +x ²)), where is a constant andx is the distance along the surface. It is shown that for > -1/2 the solution develops from a similarity solution which is valid for small values ofx to one which is valid for large values ofx. However, when -1/2 no similarity solutions exist for large values ofx and it is found that there are two cases to consider, namely < -1/2 and = -1/2. The wall temperature and the velocity at large distances along the plate are determined for a range of values of .Notation g Gravitational acceleration - k Thermal conductivity of the saturated porous medium - K Permeability of the porous medium - l Typical streamwise length - q _w Uniform heat flux on the wall - Ra Rayleigh number, =gK(q _w /k)l/(v) - T Temperature - Too Temperature far from the plate - u, v Components of seepage velocity in the x and y directions - x, y Cartesian coordinates - Thermal diffusivity of the fluid saturated porous medium - The coefficient of thermal expansion - An undetermined constant - Porosity of the porous medium - Similarity variable, =y(1+x ) ^/3/x ^1/3 - A preassigned constant - Kinematic viscosity - Nondimensional temperature, =(T – T )Ra^1/3 k/qw - Similarity variable, = =y(log_e x)^1/3/x ^2/3 - Similarity variable, =y/x ^2/3 - Stream function     

The rheology of polymeric liquid crystals

The molecular theory of Doi has been used as a framework to characterize the rheological behavior of polymeric liquid crystals at the low deformation rates for which it was derived, and an appropriate extension for high deformation rates is presented. The essential physics behind the Doi formulation has, however, been retained in its entirety. The resulting four-parameter equation enables prediction of the shearing behavior at low and high deformation rates, of the stress in extensional flows, of the isotropic-anisotropic phase transition and of the molecular orientation. Extensional data over nearly three decades of elongation rate (10^–2–10¹) and shearing data over six decades of shear rate (10^–2–10⁴) have been correlated using this analysis. Experimental data are presented for both homogeneous and inhomogeneous shearing stress fields. For the latter, a 20-fold range of capillary tube diameters has been employed and no effects of system geometry or the inhomogeneity of the flow-field are observed. Such an independence of the rheological properties from these effects does not occur for low molecular weight liquid crystals and this is, perhaps, the first time this has been reported for polymeric lyotropic liquid crystals; the physical basis for this major difference is discussed briefly. A Semi-empirical constant in eq. (18), N/m² - c rod concentration, rods/m³ - c ^* critical rod concentration at which the isotropic phase becomes unstable, rods/m³ - C interaction potential in the Doi theory defined in eq. (3) - d rod diameter, m - D semi-empirical constant in eq. (19), s^–1 - D _r lumped rotational diffusivity defined in eq. (4), s^–1 - rotational diffusivity of rods in a concentrated (liquid crystalline) system, s^–1 - D _ro rotational diffusivity of a dilute solution of rods, s^–1 - f distribution function defining rod orientation - F tensorial term in the Doi theory defined in eq. (7) (or eq. (19)), s^–1 - G tensorial term in the Doi theory defined in eq. (8) - K _B Boltzmann constant, 1.38 × 10^–23 J/K-molecule - L rod length, m - S scalar order parameter - S tensor order parameter defined in eq. (5) - t time, s - T absolute temperature, K - u unit vector describing the orientation of an individual rod - rate of change ofu due to macroscopic flow, s^–1 - v fluid velocity vector, m/s - v velocity gradient tensor defined in eq. (9), s^–1 - V mean field (aligning) potential defined in eq. (2) - x coordinate direction, m - Kronecker delta (= 0 if = 1 if = ) - _r ratio of viscosity of suspension to that of the solvent at the same shear stress - _s solvent viscosity, Pa · s - ^* viscosity at the critical concentrationc ^*, Pa · s - v ₁, v₂ numerical factors in eqs. (3) and (4), respectively - deviatoric stress tensor, N/m² - volume fraction of rods - ⁰ constant in eq. (16) - ^* volume fraction of rods at the critical concentrationc ^* - average over the distribution functionf(u, t) (= d ²u f(u, t)) - gradient operator - d ²u integral over the surface of the sphere (|u| = 1)     

On nonlinear problems of mixed type: A qualitative theory using infinite-dimensional center manifolds

We consider the equation a(y)u_xx+div_y(b(y)_yu)+c(y)u=g(y, u) in the cylinder (–l,l)×, being elliptic where b(y)>0 and hyperbolic where b(y)<0. We construct self-adjoint realizations in L₂() of the operatorAu= (1/a) div_y(b_yu)+(c/a) in the case ofb changing sign. This leads to the abstract problem u_xx+Au=g(u), whereA has a spectrum extending to + as well as to –. For l= it is shown that all sufficiently small solutions lie on an infinite-dimensional center manifold and behave like those of a hyperbolic problem. Anx-independent cross-sectional integral E=E(u, u_x) is derived showing that all solutions on the center manifold remain bounded forx ±. For finitel, all small solutionsu are close to a solution on the center manifold such that u(x)-(x) Ce ^-(1-|x|) for allx, whereC and are independent ofu. Hence, the solutions are dominated by hyperbolic properties, except close to the terminal ends {±1}×, where boundary layers of elliptic type appear.     

Saint-Venant's principle in linear two-dimensional elasticity for non-striplike domains

Let be a simply connected domain in the x ₁-x ₂ plane which lies within the strip 0<x ₂, is a simple closed piecewise smooth curve. Let l= [(x ₁, x ₂): (x ₁, x ₂) and x ₁>0], _l = [(x ₁ x ₂): (x ₁ ,x ₂) and x ₁>1>0].Suppose that a two-dimensional homogeneous isotropic elastic body occupies , that a self-equilibrated stress loading is applied to - l, and that l is stress-free. Knowles [2] and Flavin [6] showed that the elastic energy in _l decays exponentially with respect to l with an exponential decay constant of the form k/b, where k is a universal constant. It is shown here that a decay constant of the form c/ may be obtained where c is a universal constant and is a characteristic dimension of , which is more appropriate than b for general non-striplike domains. In addition, an appropriate decay theorem is obtained for coil-like domains.     

Optical co-ordinates in general relativity 2 — the problem of distance

Summary Let denote the congruence of null geodesics associated with a given optical observer inV ₄. We prove that determines a unique collection of vector fieldsM₍₎ ( =1, 2, 3) and ₍₀₎ overV ₄, satisfying a weak version of Killing's conditions.This allows a natural interpretation of these fields as the infinitesimal generators of spatial rotations and temporal translation relative to the given observer. We prove also that the definition of the fieldsM₍₎ and ₍₀₎ is mathematically equivalent to the choice of a distinguished affine parameter f along the curves of, playing the role of a retarded distance from the observer.The relation between f and other possible definitions of distance is discussed.

---

Sommario Sia la congruenza di geodetiche nulle associata ad un osservatore ottico assegnato nello spazio-tempoV ₄. Dimostriamo che determina un'unica collezione di campi vettorialiM₍₎ ( =1, 2, 3) e ₍₀₎ inV ₄ che soddisfano una versione in forma debole delle equazioni di Killing. Ciò suggerisce una naturale interpretazione di questi campi come generatori infinitesimi di rotazioni spaziali e traslazioni temporali relative all'osservatore assegnato. Dimostriamo anche che la definizione dei campiM₍₎, ₍₀₎ è matematicamente equivalente alla scelta di un parametro affine privilegiato f lungo le curve di, che gioca il ruolo di distanza ritardata dall'osservatore. Successivamente si esaminano i legami tra f ed altre possibili definizioni di distanza in grande.

---

---

Work performed in the sphere of activity of: Gruppo Nazionale per la Fisica Matematica del CNR.     

Finite difference solution of unsteady natural convection boundary layer flow over an inclined plate with variable surface temperature

The unsteady natural convection boundary layer flow over a semi-infinite inclined plate is considered with the wall temperatureT _w ,(x) (=T +ax ⁿ )varying as the power of the axial coordinate. The governing equations are solved by an implicit finite difference scheme of Crank-Nicolson type. Numerical results are obtained for different values of Prandtl number, Grashof number and n for different angles of inclination. The steadystate velocity and temperature profiles, local and average skin frictions and Nusselt numbers are shown graphically. The effects of the angle of inclination and exponent n on velocity and temperature profiles, skin friction and Nusselt number have been discussed. The velocity, temperature and Nusselt number of the present study are compared with the available results and a good agreement is found to exist between the two.

---

Differenzlösung für nichtstationäre natürliche Grenzschicht-Konvektionsströmung an einer geneigten Platte mit veränderlicher Oberflächentemperatur

Zusammenfassung Die nichtstationäre natürliche Grenzschicht-Konvektionsströmung an einer halbunendlichen geneigten Platte wird unter Zugrundelegung der GesetzmäßigkeitT _w ,(x) (=T +ax ⁿ für die Wandtemperatur als Funktion der Achsialkoordinate untersucht, und zwar mit Hilfe eines impliziten Differenzverfahrens vom Crank-Nicolson Typ und bei Variation der Prandtl- und Grashof-Zahlen, des Exponenten n und des Neigungswinkels. Graphisch dargestellt sind die Geschwindigkeits-und Temperaturprofile im stationären Zustand, die örtlichen und gemittelten Reibungsbeiwerte und der Nusselt-Zahlen. Der Einfluß des Neigungswinkels und des Exponenten n auf diese Größe wird diskutiert. Im Vergleich mit den Ergebnissen aus anderen Arbeiten konnte gute Übereinstimmung festgestellt werden.

---

Nomenclature g acceleration due to gravity - Gr _L Grashof number at x=L - L length of the plate - n exponent in the power law variation of the wall temperature - Nu _x local Nusselt number - Nu _X dimensionless local Nusselt number - average Nusselt number - dimensionless average Nusselt number - p pressure - Pr Prandtl number - t time - t dimensionless time - T temperature - Tw temperature on the plate - T dimensionless temperature - u x-velocity component - U dimensionlessX-velocity component - v y-velocity component - V dimensionlessY-velocity component - x spatial coordinate along the plate - X dimensionless spatial coordinate along the plate - y spatial coordinate normal to the plate - Y dimensionless spatial coordinate normal to the plate Greek symbols thermal diffusivity - ß volumetric coefficient of thermal expansion - t dimensionless time-step - X dimensionless finite difference grid spacing in theX-direction - Y dimensionless finite difference grid spacing in theY-direction - angle of inclination of plate with horizontal - kinematic viscosity - density - _x local skin friction - _X dimensionless local skin friction - average skin friction - dimensionless average skin friction     

Laminar assisting mixed convection heat transfer from a vertical isothermal plate to water with variable physical properties

The steady laminar boundary layer flow, with an external force, along a vertical isothermal plate is studied in this paper. The external force may be produced either by the motion of the plate or by a free stream. The fluid is water whose density-temperature relationship is non-linear at low temperatures and viscosity and thermal conductivity are functions of temperature. The results are obtained with the numerical solution of the boundary layer equations with , k and variable across the boundary layer. Both upward and downward flow is considered. It was found that the variation of , k and with temperature has a strong influence on mixed convection characteristics.Nomenclature c_p water specific heat - f dimensionless stream function - g gravitational acceleration - Gr_x local Grashof number - k thermal conductivity - Nu_x local Nusselt number - Pr Prandtl number - Pr_a ambient Prandtl number - Re_x local Reynolds number - s salinity - T water temperature - T_a ambient water temperature - T_o plate temperature - u vertical velocity - u_a free stream velocity - u_o plate velocity - v horizontal velocity - x vertical coordinate - y horizontal coordinate - pseudo-similarity variable - nondimensional temperature - dynamic viscosity - _f film dynamic viscosity - _o dynamic viscosity at plate surface - kinematic viscosity - buoyancy parameter - water density - _a ambient water density - _f film water density - _o water density at plate surface - physical stream function     

Transcendentally small transversality in the rapidly forced pendulum

The rapidly forced pendulum equation with forcing sin((t/), where =<₀^p,p = 5, for ₀, sufficiently small, is considered. We prove that stable and unstable manifolds split and that the splitting distanced(t) in the ( ,t) plane satisfiesd(t) = sin(t/) sech(/2) +O( ₀ exp(–/2)) (2.3a) and the angle of transversal intersection,, in thet = 0 section satisfies 2 tan/2 = 2S _s = (/2) sech(/2) +O(( ₀ /) exp(–/2)) (2.3b) It follows that the Melnikov term correctly predicts the exponentially small splitting and angle of transversality. Our method improves a previous result of Holmes, Marsden, and Scheuerle. Our proof is elementary and self-contained, includes a stable manifold theorem, and emphasizes the phase space geometry.     

Exact Solutions of the Hydrodynamic Equations Derived from Partially Invariant Solutions

The paper proposes a heuristic approach to constructing exact solutions of the hydrodynamic equations based on the specificity of these equations. A number of systems of hydrodynamic equations possess the following structure: they contain a reduced system of n equations and an additional equation for an extra function w. In this case, the reduced system, in which w = 0, admits a Lie group G. Taking a certain partially invariant solution of the reduced system with respect to this group as a seed:rdquo; solution, we can find a solution of the entire system, in which the functional dependence of the invariant part of the seed solution on the invariants of the group G has the previous form. Implementation of the algorithm proposed is exemplified by constructing new exact solutions of the equations of rotationally symmetric motion of an ideal incompressible liquid and the equations of concentrational convection in a plane boundary layer and thermal convection in a rotating layer of a viscous liquid.     

Modellvorstellung zur turbulenten Filmkondensation strömenden Dampfes

Zusammenfassung Der Wärmeübergang bei turbulenter Film kondensation strömenden Dampfes an einer waagerechten ebenen Platte wurde mit Hilfe der Analogie zwischen Impuls-und Wärmeaustausch untersucht. Zur Beschreibung des Impulsaustausches im Film wurde ein Vierbereichmodell vorgestellt. Nach diesem Modell wird die wellige Phasengrenze als starre rauhe Wand angesehen. Die Abhängigkeit einer Schubspannungs-Nusseltzahl von der Film-Reynoldszahl und Prandtlzahl wurde berechnet und dargestellt.

---

A model for turbulent film condensation of flowing vapour

The heat transfer in turbulent film condensation of flowing vapour on a horizontal flat plate was investigated by means of the analogy between momentum and heat transfer. To describe the momentum transfer in the film a four-region model was presented. With this model the wavy interfacial surface is treated as a stiff rough wall. A shear Nusselt number has been calculated and represented as a function of film Reynolds number and Prandtl number.

---

Formelzeichen a Temperaturleitkoeffizient - k Mischungswegkonstante - k _s äquivalente Sandkornrauhigkeit - Nu _x lokale Schubspannungs-Nusseltzahl,Nu _x=x_xv/uw - Pr Prandtlzahl,Pr=v/a - Pr _t turbulente Prandtlzahl,Pr _t =_m/_q - q Wärmestromdichte _q - R Wärmeübergangswiderstand - R_f Wärmeübergangswiderstand des Films - Re _F Reynoldszahl der Filmströmung - T Temperatur - U, V Geschwindigkeitskomponenten des Dampfes in waagerechter und senkrechter Richtung - u, Geschwindigkeitskomponenten des Kondensats in waagerechter und senkrechter Richtung - V Querschwankungsgeschwindigkeit des Kondensats und des Dampfes - u _/gtD Schubspannungsgeschwindigkeit an der Phasengrenze für die Dampfgrenzschicht, uD =(/)^1/2 - u _F Schubspannungsgeschwindigkeit an der Phasengrenze für den Kondensatfilm,u _F =(/)^1/2 - u _w Schubspannungsgeschwindigkeit an der Wand der Kühlplatte,u _w =(w/)^1/2 - y Wandabstand - x Wärmeübergangskoeffizient - gemittelte Kondensatfilmdicke - _s Dicke der zähen Schicht der Filmströmung an der welligen Phasengrenze - ₄ Dicke der zähen Schicht der Filmströmung an der gemittelten glatten Phasengrenze - Wärmeleitzahl - dynamische Viskosität - v kinematische Viskosität - Dichte - Oberflächenspannung - _w Wandschubspannung - Schubspannung an der Phasengrenzfläche - _m turbulente Impulsaustauschgröße - _q turbulente Wärmeaustauschgröße Indizes d Wert des Dampfes - w Wert an der Wand - x lokaler Wert inx - Wert an der Phasengrenze Stoffgrößen ohne Index gelten für das Kondensat     

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Der Spannungs- und Verschiebungszustand drehsymmetrischer Membrane mit beliebig gekrümmter Meridiankurve

Zusammenfassung Die Einführung von Zylinderkoordinaten (x, r, ) in die Gleichgewichtsbedingungen der Schnittkräfte bzw. in die Beziehungen zwischen Verzerrung und Verschiebungen am differentialen Schalenabschnitt ermöglicht die Berechnung des Spannungs- und Verschiebungszustandes von drehsymmetrischen Membranen mit beliebig gekrümmter Meridiankurve auf die Integration einer einfachen, linearen partiellen Differentialgleichung zweiter Ordnung für eine charakteristische FunktionF bzw. zurückzuführen. Eine geschlossene Lösung und damit eine Darstellung der Schnittkräfte und Verschiebungen durch explizite Formeln ist bei harmonischer Belastung cosn für zwei Funktionsgruppen=x ² und=x ^–3 möglich. Im Sonderfall der drehsymmetrischen und der antimetrischen Belastung mitn=0 undn=1 gelten die Gleichungen der Schnitt- und Verschiebungsgrößen für eine beliebige Meridianfunktion=(). Die Betrachtungen der Randbedingungen offener Schalen bei harmonischer Belastung geben über die infinitesimalen Deformationen einer drehsymmetrischen Membran mit überall negativer Krümmung Aufschluß.     

Transport in ordered and disordered porous media IV: Computer generated porous media for three-dimensional systems

In the method of volume averaging, the difference between ordered and disordered porous media appears at two distinct points in the analysis, i.e. in the process of spatial smoothing and in the closure problem. In theclosure problem, the use of spatially periodic boundary conditions isconsistent with ordered porous media and the fields under consideration when the length-scale constraint,r ₀L is satisfied. For disordered porous media, spatially periodic boundary conditions are an approximation in need of further study.In theprocess of spatial smoothing, average quantities must be removed from area and volume integrals in order to extractlocal transport equations fromnonlocal equations. This leads to a series of geometrical integrals that need to be evaluated. In Part II we indicated that these integrals were constants for ordered porous media provided that the weighting function used in the averaging process contained thecellular average. We also indicated that these integrals were constrained by certain order of magnitude estimates for disordered porous media. In this paper we verify these characteristics of the geometrical integrals, and we examine their values for pseudo-periodic and uniformly random systems through the use of computer generated porous media.

Nomenclature

Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - a _i i=1, 2, 3 gaussian probability distribution used to locate the position of particles - I unit tensor - L general characteristic length for volume averaged quantities, m - L characteristic length for , m - L characteristic length for , m - characteristic length for the -phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1, 2, 3 lattice vectors, m - m convolution product weighting function - m _v special convolution product weighting function associated with the traditional volume average - n _i i=1, 2, 3 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - r position vector, m - r _m support of the weighting functionm, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume,, m³ - x positional vector locating the centroid of an averaging volume, m - x ₀ reference position vector associated with the centroid of an averaging volume, m - y position vector locating points relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - /L, small parameter in the method of spatial homogenization - standard deviation ofa _i - _r standard deviation ofr - _r intrinsic phase average of      

Impacts of local dispersion and first-order decay on solute transport in randomly heterogeneous porous media

Stochastic subsurface transport theories either disregard local dispersion or take it to be constant. We offer an alternative Eulerian-Lagrangian formalism to account for both local dispersion and first-order mass removal (due to radioactive decay or biodegradation). It rests on a decomposition of the velocityv into a field-scale componentv , which is defined on the scale of measurement support, and a zero mean sub-field-scale componentv _s , which fluctuates randomly on scales smaller than. Without loss of generality, we work formally with unconditional statistics ofv _s and conditional statistics ofv . We then require that, within this (or other selected) working framework,v _s andv be mutually uncorrelated. This holds whenever the correlation scale ofv is large in comparison to that ofv _s . The formalism leads to an integro-differential equation for the conditional mean total concentration c which includes two dispersion terms, one field-scale and one sub-field-scale. It also leads to explicit expressions for conditional second moments of concentration cc. We solve the former, and evaluate the latter, for mildly fluctuatingv by means of an analytical-numerical method developed earlier by Zhang and Neuman. We present results in two-dimensional flow fields of unconditional (prior) mean uniformv . These show that the relative effect of local dispersion on first and second moments of concentration dies out locally as the corresponding dispersion tensor tends to zero. The effect also diminishes with time and source size. Our results thus do not support claims in the literature that local dispersion must always be accounted for, no matter how small it is. First-order decay reduces dispersion. This effect increases with time. However, these concentration moments c and cc of total concentrationc, which are associated with the scale below, cannot be used to estimate the field-scale concentrationc directly. To do so, a spatial average over the field measurement scale is needed. Nevertheless, our numerical results show that differences between the ensemble moments ofc and those ofc are negligible, especially for nonpoint sources, because the ensemble moments ofc are already smooth enough.     

Transport in ordered and disordered porous media III: Closure and comparison between theory and experiment

In this paper we examine the closure problem associated with the volume averaged form of the Stokes equations presented in Part II. For both ordered and disordered porous media, we make use of a spatially periodic model of a porous medium. Under these circumstances the closure problem, in terms of theclosure variables, is independent of the weighting functions used in the spatial smoothing process. Comparison between theory and experiment suggests that the geometrical characteristics of the unit cell dominate the calculated value of the Darcy's law permeability tensor, whereas the periodic conditions required for thelocal form of the closure problem play only a minor role.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface associated with the local closure problem, m² - A _p surface area of a particle, m² - b vector used to represent the pressure deviation, m^–1 - B ⁰ B+I, a second order tensor that maps v _m ontov - B second-order tensor used to represent the velocity deviation - d _p 6V _p/A_p, effective particle diameter, m - d a vector related to the pressure, m - D a second-order tensor related to the velocity, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor calculated on the basis of a spatially periodic model, m² - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p characteristic length for the volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - characteristic length (pore scale) for the-phase - _i i=1, 2, 3 lattice vectors, m - weighting function - m(-y) , convolution product weighting function - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - n unit normal vector pointing from the-phase toward the -phase - p pressure in the-phase, N/m² - p _m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p – p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function - r position vector, m - r position vector locating points in the-phase, m. - V averaging volume, m³ - B volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v _m superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - v traditional superficial volume averaged velocity, m/s - v – v _m , spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the -phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * , weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

Solution of regular beam equations in arbitrary emission conditions on a curvilinear surface

The regular beam equations are solved analytically for the case of emission from an arbitrary surface in conditions of total space charge (-mode) and in a given external magnetic field H (§2) for temperature-limited emission (T-mode), in an external magnetic field H (§3); and for emission with nonzero initial velocity (§4). The emitter is taken as the coordinate surface x¹=0 in an orthogonal system x¹ (i = =1,2,3), while the current density J and field on it are given functions j(x², x³), (x², x³. The solution is written as series in (x¹) with coefficients dependent on x², x³, determined from recurrence relations. For emission in the -mode and H 0, =1/3; for temperature-limited emission, =1/2; with nonzero initial velocity, =1. The results are extended to the case of a beam in the presence of a moving background of uniform density (5).     

Backward Uniqueness for Parabolic Equations

It is shown that a function u satisfying |_t+u|M(|u|+|u|), |u(x, t)|Me^M|x|2 in (ⁿ \ (B_R) × [0, T] and u(x, 0) = 0 for xⁿ \ B_R must vanish identically in ⁿ \ B_R×[0, T].     

Effect of measuring volume length on two-component laser velocimeter measurements in a turbulent boundary layer

The effects of finite measuring volume length on laser velocimetry measurements of turbulent boundary layers were studied. Four different effective measuring volume lengths, ranging in spanwise extent from 7 to 44 viscous units, were used in a low Reynolds number (Re=1440) turbulent boundary layer with high data density. Reynolds shear stress profiles in the near-wall region show that u v strongly depends on the measuring volume length; at a given y-position, u v decreases with increasing measuring volume length. This dependence was attributed to simultaneous validations on the U and V channels of Doppler bursts coming from different particles within the measuring volume. Moments of the streamwise velocity showed a slight dependence on measuring volume length, indicating that spatial averaging effects well known for hot-films and hot-wires can occur in laser velocimetry measurements when the data density is high.List of symbols time-averaged quantity - u wall friction velocity, ( _w /)^1/2 - v kinematic viscosity - d _p pinhole diameter - l _eff spanwise extent of LDV measuring volume viewed by photomultiplier - l ⁺ non-dimensional length of measuring volume, l _eff u /v - y ⁺ non-dimensional coordinate in spanwise direction, y u /v - z ⁺ non-dimensional coordinate in spanwise direction, z u /v - U ⁺ non-dimensional mean velocity, /u - u instantaneous streamwise velocity fluctuation, U &#x2329;U - v instantaneous normal velocity fluctuation, V–V - u RMS streamwise velocity fluctuation, u ^21/2 - v RMS normal velocity fluctuation, v ^21/2 - Re Reynolds number based on momentum thickness, U 0/v - R _uv cross-correlation coefficient, u v/u v - R₁₂(0, 0, z) two point correlation between u and v with z-separation, <u(0, 0, 0) v (0, 0, z)>/<u(0, 0, 0) v (0, 0, 0)> - N rate at which bursts are validated by counter processor - T Taylor time microscale, u (dv/dt²)^–1/2     

On forced vibration of anisotropic cylinders

Summary The dynamic response of a circular cylinder with thick walls of transverse curvilinear isotropy subjected to a uniformly distributed pressure varying periodically with time is analyzed by means of the Laplace transformation, and the exact solution is obtained in closed form. The previously obtained solutions for forced vibrations with isotropy, and free vibrations with transverse curvilinear isotropy are included as special cases of the general results reported here.Nomenclature t time - r, , z cylindrical coordinates - _ii components of normal strain - _ii components of normal stress - u radial displacement - c _ij elastic constant - mass density - c ² c ₁₁/ - ² c ₂₂/c ₁₁ - a, b inner, outer radius of the cylinder - , A, B constants - forced angular frequency - function defined by (9) - p, real, complex variables - constant defined by (14) - real number - , Lamé elastic constants - J (x) Bessel function of first kind - Y (x) Bessel function of second kind - I (x) modified Bessel function of first kind - K (x) modified Bessel function of second kind     

The moving, plane heat source in an elastic medium

Summary This note presents an exact solution for the stress and displacement field in an unbounded and transversely constrained elastic medium resulting from the motion of a plane heat source travelling through the medium at constant speed in the direction normal to the source plane.Nomenclature mass density - diffusivity - thermal conductivity - Q heat emitted by plane heat source per unit time per unit area - speed of propagation of plane heat source - shear modulus - Poisson's ratio - T temperature - _x, _y, _z normal stress components - u _x, u_y, u_z displacement components - c speed of irrotational waves - t time - x, y, z Cartesian coordinates - =x–vt moving coordinate