两种湍流模型时域颤振计算方法研究

采用时域计算分析方法进行了机翼跨音速颤振特性研究。在结构运动网格的基础上,采用格点格式有限体积方法进行空间离散和双时间全隐式方法进行时间推进求解雷诺平均N-S方程。针对流动粘性分别应用了SST湍流模型和SSG雷诺应力模型,通过对跨音速标模算例AGARD445.6机翼的计算结果与实验值的对比分析,其中应用SST湍流模型得到的颤振速度与实验值最为接近,特别是在跨音速段平均相对误差在3%以内;并且计算结果整体上反映了跨音速颤振"凹坑"物理特性,验证了方法的有效性。     

高压捕获翼构型亚跨超流动特性数值研究

为研究高压捕获翼布局在亚跨超条件下的流动特性, 选取圆锥?圆台机体组合捕获翼概念构型, 在马赫数0.3 ~ 3速域范围内, 选取典型状态点, 采用数值模拟在 0°攻角条件下进行了计算和分析. 结果表明, 在整个速域范围内, 由于机体与捕获翼在对称面附近的垂向距离最小, 因此二者之间的气动干扰最为明显, 且沿展向逐渐减弱. 同时, 随马赫数增大, 机体与捕获翼间的流场结构明显不同, 具体表现为: 当Ma<0.5时, 未出现流动分离现象, 当Ma>0.5时, 机体后段开始出现明显的流动分离, 由于捕获翼与机体形成先收缩后扩张的等效通道, 捕获翼下表面和机体上表面的压力均先减小后增大; 进入跨声速速域后, 在捕获翼的影响下, 流动分离更加明显, 机体与捕获翼之间开始出现激波, 并且与分离区相互作用, 同时出现激波串, 捕获翼下表面产生明显的压力波动现象, Ma=1.5时, 通道内激波位置基本到达机体尾部, 分离区基本消失; 当Ma>2以后, 整个流场呈现以激波为主导的结构形式, 捕获翼下表面和机体上表面的压力分布逐渐趋于平缓.      

Validation of CFD‐CSD coupling interface methodology using commercial codes

Coupling interface between computational fluid dynamics (CFD) and computational structural dynamics (CSD) is required to provide exchange of information for the simulation of fluid–structure interaction (FSI) phenomena. Accuracy and consistency of information exchanged through coupling interface between the independent CFD and CSD solvers plays a central role in the simulation and prediction of FSI phenomenon, like flutter. In this paper validation of an implemented coupling interface methodology is presented for subsonic, transonic and near supersonic mach regime. The test case chosen for this purpose is the flutter of AGARD445.6 standard I‐wing weakened model configuration for subsonic to near transonic flow regime. Gambit^® and Fluent^® are used for CFD grid generation and solution of fluid dynamic equations, respectively. CSD modeling and simulation are provided by numerical time integration of modal dynamic equations derived through the finite element modeling in ANSYS^® environment. Copyright © 2009 John Wiley & Sons, Ltd.     

Separated Flow and Buffeting Control

In transonic flow conditions, the shock wave/turbulent boundary layer interaction and the flow separations on the upper wing surfaces of civil aircraft induce flow instabilities, ‘buffet’ and then structural vibrations, ‘buffeting’. Buffeting can greatly affect aerodynamic behavior. The buffeting phenomenon appears when the aircraft's Machnumber or angle of attack increases. This phenomenon limits the aircraft's flight envelope. The objectives of this study are to cancel out or decrease the aerodynamic instabilities (unsteady separation, movement of the shock position) due to this type of flow by using control systems. The following actuators can be used: ‘Vortex Generators’ situated upstream of the shock position, a ‘Bump’ located at the shock position, and a new moving part designed by ONERA, situated on the trailing edge of the wing, the ‘Trailing Edge Deflector’ or TED. It looks like an adjustable ‘Divergent Trailing Edge’. It is an active actuator and can take different deflections or be driven by dynamic movements up to 250 Hz. Tests were performed in transonic 2D flow with models well equipped with unsteady pressure transducers. For high lift coefficients, a selected static position of the ‘Trailing Edge Deflector’ increases the wing's aerodynamic performances and delays the onset of buffet. Furthermore, in 2D flow buffet conditions, the ‘Trailing Edge Deflector’, driven by a closed-loop active control using the measurements of the unsteady wall static pressures, can greatly reduce buffet. The aerodynamic performances are not improved to the same extent by the bump actuator. From our experience, there is no effect on buffet or separated flow because of the incorrect positioning of the bump. All that can be observed is a local improvement on the intensity of the shock wave when the bump is very precisely situated at the shock position. Vortex generators have a great impact on the separated flow. The separated flow instabilities are greatly reduced and buffet is totally controlled even for strong instabilities. The aerodynamic performances of the airfoil are also greatly improved.     

Nonlinear dynamics of an aeroelastic airfoil with free-play in transonic flow

Nonlinear dynamic behaviors of an aeroelastic airfoil with free-play in transonic air flow are studied. The aeroelastic response is obtained by using time-marching approach with computational fluid dynamics (CFD) and reduced order model (ROM) techniques. Several standardized tests of transonic flutter are presented to validate numerical approaches. It is found that in time-marching approach with CFD technique, the time-step size has a significant effect on the calculated aeroelastic response, especially for cases considering both structural and aerodynamic nonlinearities. The nonlinear dynamic behavior for the present model in transonic air flow is greatly different from that in subsonic regime where only simple harmonic oscillations are observed. Major features of the responses in transonic air flow at different flow speeds can be summarized as follows. The aeroelastic responses with the amplitude near the free-play are dominated by single degree of freedom flutter mechanism, and snap-though phenomenon can be observed when the air speed is low. The bifurcation diagram can be captured by using ROM technique, and it is observed that the route to chaos for the present model is via period-doubling, which is essentially caused by the free-play nonlinearity. When the flow speed approaches the linear flutter speed, the aeroelastic system vibrates with large amplitude, which is dominated by the aerodynamic nonlinearity. Effects of boundary layer and airfoil profile on the nonlinear responses of the aeroelastic system are also discussed.     

A check on the energy method of predicting blade transonic stall flutter

An improved structural dynamic model of an oscillating blade in two degrees of freedom is combined with an unsteady aerodynamic model for the transonic flow about a cascade with separation, which results in a coupled system. The system is solved in an iterative way between the two models. As a check on the current energy methods, the stall flutter boundaries for two real rotors are predicted by using the present method and the results are compared with the experiments and those predicted by using an energy method.     

Mono‐block and non‐matching multi‐block structured mesh adaptation based on aerodynamic functional total derivatives for RANS flow

An enhanced goal‐oriented mesh adaptation method is presented based on aerodynamic functional total derivatives with respect to mesh nodes in a Reynolds‐Averaged Navier‐Stokes (RANS) finite‐volume mono‐block and non‐matching multi‐block‐structured grid framework. This method falls under the category of methods involving the adjoint vector of the function of interest. The contribution of a Spalart–Allmaras turbulence model is taken into account through its linearization. Meshes are adapted accordingly to the proposed indicator. Applications to 2D RANS flow about a RAE2822 airfoil in transonic, and detached subsonic conditions are presented for the drag coefficient estimation. The asset of the proposed method is patent. The obtained 2D anisotropic mono‐block mesh well captures flow features as well as global aerodynamic functionals. Interestingly, the constraints imposed by structured grids may be relaxed by the use of non‐matching multi‐block approach that limits the outward propagation of local mesh refinement through all of the computational domain. The proposed method also leads to accurate results for these multi‐block meshes but at a fraction of the cost. Finally, the method is also successfully applied to a more complex geometry, namely, a mono‐block mesh in a 3D RANS transonic flow about an M6 wing. Copyright © 2016 John Wiley & Sons, Ltd.     

A finite element solution of unsteady two-dimensional flow in cascades

A theory is presented for unsteady two-dimensional potential transonic flow in cascades of compressor and turbine blades using a mesh of triangular finite elements. The theory leads to a computer program, FINSUP, which is fast and has moderate storage requirements, so that it can be run on a personal computer. Comparisons with other theories in special cases show that the program is accurate in subsonic flow, and that in supersonic flow, although the wave effects are smeared by the numerical process, the results for overall blade force and moment have acceptable accuracy. The program is useful for engineering assessment of unstalled flutter of actual compressor and turbine blades.     

Investigation of flow separation in a transonic-fan linear cascade using visualization methods

An extensive experimental study into the nature of the separated flows on the blade suction surface of modern transonic fans is described in this paper. The study was a subtask of a larger experimental effort focused on blade flutter excited by flow separation in the blade tip region. The tip sections of airfoils on transonic fan blades are designed for precompression and consequently they differ from sections on the rest of the blade. The blade tip section was modeled by a low aspect ratio blade and therefore most of the blade tested was exposed to the secondary flow effects. The aim of this work was to supply reliable data on flow separation on transonic fan blades for validation of future analytical studies. The experimental study focused on two visualization techniques: surface flow visualization using dye oils and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction surface of the blade was separated over a large portion of the blade, and the separated area increased with increasing inlet Mach number. For the supersonic inlet flow condition, the flow was attached from the leading edge up to the point where a bow shock from the upper neighboring blade imposed on the blade surface. Downstream, there was a separated flow region in which air flowed in the direction opposite the inlet flow. Finally, past the separated flow region, the flow reattached to the blade surface. For subsonic inlet flow, the low cascade solidity resulted in an increased area of separated flow. For supersonic flow conditions, the low solidity resulted in an improvement in flow over the suction surface.     

Unsteady aerodynamic reduced-order modeling of an aeroelastic wing using arbitrary mode shapes

Computational fluid dynamics (CFD) based unsteady aerodynamic reduced-order model (ROM) can offer significant improvements to the efficiency of transonic aeroelastic analysis. To construct a ROM based on mode shapes, one run of CFD solver is needed to compute aerodynamic responses corresponding to mode excitations. When mode shapes change with structure, another run of the CFD solver is required to construct the new ROM. The typically large computational cost associated with repeated runs of the CFD solver impedes the application of existing unsteady aerodynamic reduced-order modeling methods to transonic aeroelastic design optimization and aeroelastic uncertainty analysis. This paper demonstrates a method that can replace the CFD solver used in the process of existing unsteady aerodynamic reduced-order modeling. It can produce aerodynamic responses corresponding to mode excitations for arbitrary mode shapes within a few seconds. Computational cost can be reduced by two orders of magnitude using the mode excitations and the corresponding aerodynamic responses computed by the method to construct the ROMs used for flutter analyses in aeroelastic design optimization or aeroelastic uncertainty analysis in transonic regime compared with the existing unsteady aerodynamic reduced-order modeling methods. Results show that the method can accurately produce the aerodynamic responses corresponding to the mode excitations and predict the flutter characteristics of AGARD 445.6 wings root-attached in three different ways.