On the interaction between two consecutive elongated bubbles in a vertical pipe

The motion of elongated air bubbles in a vertical pipe filled with water is studied quantitatively using video imaging of the flow and subsequent digital image processing of the recorded sequence of images. Experiments are carried out to determine the influence of the separation distance between two consecutive bubbles (liquid slug length) upon the behavior of the trailing bubble in vertical slug flow. The details of the trailing bubble acceleration and merging process are observed and the instantaneous parameters of the trailing bubble, such as its shape, velocity, acceleration, etc., are measured as a function of the separation distance. The leading bubble is found to be unaffected by the trailing elongated bubble.     

水平刚性面下方水下爆炸气泡垂向运动的理论研究

为了研究边界面对水下爆炸气泡脉动的影响,根据势流理论建立了水平刚性面下方在浮力作用下作垂向运动的水下爆炸气泡的理论模型,编制计算程序进行求解。对水下爆炸气泡脉动运动的特点、流场的速度和压力的分布、气泡引起的载荷形式进行了分析。结果表明此模型能够反映水下爆炸气泡和周围流体介质的运动规律,并能进行定量的计算。     

Spatial distribution of void fraction within a liquid slug and some other related slug parameters

The structure of vertical upward slug flow in a pipe is studied. The distribution of the phases in the Taylor bubble zone and the liquid slug zone is investigated by simultaneous measurements with two optical fiber probes. In the Taylor bubble zone the shape of the Taylor bubble and the distribution of the bubble length is reported. In the liquid slug region, the distribution of the void fraction is obtained over a dense grid in both the axial and radial directions. These experimental results shed some light on the hydrodynamics of the two-phase slug flow, in particular regarding the production of the dispersed bubbles and their distribution along the liquid slug.     

Development of co-current air–water flow in a vertical pipe

Measurements of the cross-sectional distribution of the gas fraction and bubble size distributions were conducted in a vertical pipe with an inner diameter of 51.2 mm and a length of about 3 m for air/water bubbly and slug flow regimes. The use of a wire-mesh sensor obtained a high resolution of the gas fraction data in space as well as in time. From this data, time averaged values for the two-dimensional gas fraction profiles were decomposed into a large number of bubble size classes. This allowed the extraction of the radial gas fraction profiles for a given range of bubble sizes as well as data for local bubble size distributions. The structure of the flow can be characterized by such data. The measurements were performed for up to 10 different inlet lengths and for about 100 combinations of gas and liquid volume flow rates. The data is very useful for the development and validation of meso-scale models to account for the forces acting on a bubble in a shear liquid flow and models for bubble coalescence and break-up. Such models are necessary for the validation of CFD codes for the simulation of bubbly flows.     

Behavior of a small single bubble rising in a rotating flow field

A small single bubble was generated with a single-hole nozzle facing upward in a water bath contained in a rotating cylindrical vessel. The bubble size falls in the surface tension force dominant regime. The vertical, radial, and tangential migration velocities of the bubble were measured with two CCD cameras and a high-speed video camera. The tangential velocity component of water flow was measured with particle image velocimetry. A helical motion of the bubble was observed under every experimental condition. The direction of the helical motion was the same as that of the tangential velocity component. This helical motion is associated with the large initial shape deformation of the bubble near the nozzle exit and the subsequent regular shedding of vortices behind it. The period and amplitude of the helical motion were obtained by analyzing the trajectory of the bubble. These quantities were non-dimensionalized by the volume equivalent bubble diameter and the terminal bubble velocity in the vertical direction and correlated as functions of the Eotvos number. Empirical equations were proposed for the period and amplitude. Originally published in the Journal of JSEM, Vol. 4, No. 2, pp. 38–45 (2004).     

Numerical study of bubble rise and interaction in a viscous liquid

In this article, the flow instabilities during the rise of a single bubble in a narrow vertical tube are studied using a transient two-dimensional/axisymmetric model. To predict the shape of the bubble deformation, the Navier-Stokes equations in addition to an advection equation for liquid volume fraction are solved. A modified volume-of-fluid technique based on Youngs' algorithm is used to track the bubble deformation. To validate the model, the results of simulations for terminal rise velocity and bubble shape are compared with those of the experiments. The effect of different parameters such as initial bubble radius, channel height, liquid viscosity and surface tension on the shape and rise velocity of the bubble is investigated.     

Bubble behaviors of geldart B particle in a pseudo two-dimensional pressurized fluidized bed

Pressurized fluidized beds have been developed in quite a few industrial applications because of intensified heat and mass transfer and chemical reaction. The bubble behaviors under elevated pressure, strongly influencing the fluidization and reaction conversion of the whole system, are of great research significance. In this work, the bubble behaviors of Geldart B particle in a pseudo two-dimensional (2D) pressurized fluidized bed were experimentally studied based on digital image analysis technique. The effects of pressure and fluidization gas velocity on the general bubble behaviors (i.e., size, shape and spatial distribution) and the dynamic characteristics, such as the time-evolution of voidage distribution and local flow regimes, were comprehensively investigated. Results show that increasing pressure reduces the stability of bubbles and facilitates gas passing through the emulsion phase, resulting in the “smoother” fluidization state with smaller bubbles and declined bubble fraction and standard deviation. The equivalent bubble diameter and bubble aspect ratio increase with the increasing gas velocity while decrease as pressure rises. The elevated pressure reduces bubbles extension in the vertical direction, prohibits the “short pass” of fluidization gas in large oblong bubbles/slugs and benefits the gas–solid interaction. The flow regimes variation with gas velocity is affected by the elevated pressure, and demonstrates different features in different local positions of the bed.     

Modeling of bubble coalescence and break-up considering turbulent suppression phenomena in bubbly two-phase flow

New mechanistic bubble coalescence and break-up models considering turbulent suppression phenomena, which can possibly occur in the high liquid velocity condition of turbulent bubbly two-phase flow, are presented. The energy exchange mechanism between a turbulent eddy and interfacial structure was taken into account in the efficiency terms. Numerical simulations of turbulent bubbly flow were conducted in a CFD code to evaluate the newly developed models, in comparison with other advanced models coupled with a bubble-induced turbulent effect for one-group interfacial area transport equation. Local measurements of the bubble characteristics on the bubble size evolution along a vertical pipe flow were performed at KAERI-VAWL test facility using the five-sensor conductivity probe method to provide database for models validation. Results from the calculation clearly show the improvements of the newly developed models.     

Large scale structure in gas-liquid mixture flows

Relatively slow variation in mixture void fraction in gas-liquid mixture flows are indicated by low pass filter averaging. The slow void fluctuations are found to have a regular characteristic frequency or scale in the churn flow regime or near the boundary with the dispersed bubble flow regime. These regular disturbances develop inherently in a vertical pipe flow in strength and in size and are not due to the method of flow mixing. There was no evidence of distinctive gas slugs in the flow, and the structures were identified as large clouds of bubbles which moved faster than the average velocity, growing in size and strength as they moved with the flow. The magnitude of the voidage fluctuations in the churn flow regime was on average 57% of the value for a slug flow. The large scale bubble clouds convect coherently over relatively long distances at up to 1.45 times the mean mixture flow velocity at a gas volume flow fraction of 0.4. In the bubble flow regime, the slow voidage variations were more random in scale and were only approx. 10% of the slug flow (maximum possible) value. However, even in the bubble flow regime, the disturbances convected coherently over relatively long distances at a velocity of approx. 1.1 times the mean mixture velocity.     

Marangoni效应下气泡上升过程的FTM模拟

采用界面跟踪法FTM(Front-Tracking Method),并结合CSF(continuum surface force)模型,研究了在垂直方向上温度分布不均匀的对称流场中由Marangoni效应引起的气泡上升运动问题。模拟了在不同的M a数和Pr数下单气泡及同轴双气泡的运动。研究结果表明,在不同的M a数下气泡的运动差异较大,M a数越大,气泡运动至稳态时的速度越大,且气泡运动的最大速度值与M a数呈正相关关系;增大Pr数所造成的粘度增大或热扩散率减小将削弱气泡的迁移运动;Marangoni对流中双气泡的局部运动证实了温度梯度和气泡运动速度紧密相关。     

Bubble deformation and flow structure measured by double shadow images and PIV/LIF

An experiment on bubble motion in a simple shear layer was performed in order to obtain fundamental knowledge of the force on the bubble and its lateral motion induced by the surrounding flow field. We explored the flow structure in the vicinity of the bubble in one plane and its deformation in two planes by particle image velocimetry (PIV)–laser-induced fluorescence (LIF) and a projection technique for two perpendicular planes, respectively. For our experiment, we chose a single air bubble with an equivalent bubble diameter D _eq of 2~6 mm in a vertical shear flow. Velocity measurements were made using a digital high-speed CCD camera for PIV with fluorescent tracer particles. The second and third CCD cameras were used to detect the bubbles shape and motion via backlighting from an array of infrared LEDs. We quantitatively studied the three-dimensional wake structure from measurements of the two-dimensional vortex structure and approximated three-dimensional shape deformation arranged from two perpendicular bubble images.     

Interfacial structure of air-water two-phase flow in a relatively large pipe

Miniaturized four-sensor conductivity probes are used to study flow structure development in air-water bubbly flow, cap-bubbly flow, and transition to slug flow. The measurements are performed at three different elevations in a vertical round pipe with an inner diameter of 101.6 mm. The time-averaged local void fraction, interfacial velocity, and bubble number frequency are measured by the conductivity probes. Also, the interfacial area concentration and averaged bubble Sauter mean diameter are obtained. A detailed representation of the flow structure is revealed by investigating the acquired data. Furthermore, comparisons of the data at three elevations demonstrate the development of the interfacial structure along the flow direction due to bubble interactions and hydrodynamic effects. This may provide the community with a better knowledge about two-phase flow in a relatively large pipe. In addition, these data can also serve as an experimental database for investigation of the interfacial area transport in large-pipe two-phase flow. Published online: 19 November 2002 This work was performed under the auspices of the U.S. Nuclear Regulatory Commission through the Institute of Thermal-hydraulics.     

Effects of bubble size on heat transfer enhancement by sub-millimeter bubbles for laminar natural convection along a vertical plate

Injection of sub-millimeter bubbles is considered a promising technique for enhancing natural convection heat transfer for liquids. So far, we have experimentally investigated heat transfer characteristics of laminar natural convection flows with sub-millimeter bubbles. However, the effects of the bubble size on the heat transfer have not yet been understood. The purpose of this study is to clarify the effects of the bubble size on the heat transfer enhancement for the laminar natural convection of water along a vertical heated plate with uniform heat flux. Temperature and velocity measurements, in which thermocouples and a particle tracking velocimetry technique are, respectively used, are conducted to investigate heat transfer and flow characteristics for different bubble sizes. Moreover, two-dimensional numerical simulations are performed to comprehensively understand the effects of bubble injection on the flow near the heated plate. The result shows that the ratio of the heat transfer coefficient with sub-millimeter-bubble injection to that without injection ranges from 1.3 to 2.2. The result also shows that for a constant bubble flow rate, the heat transfer coefficient ratio increases with a decrease in the mean bubble diameter. It is expected from our estimation based on both experimental data and simulation results that this increase results from an increase in the advection effect due to bubbles.     

环形喷管喷口气泡演化的实验研究

水下气泡的发展演化及气泡动力学行为是气液两相动力学的基础理论与水下射流应用的重要基础. 环形喷管/喷口形成的气泡及气体射流具有其不同于圆孔实心射流的特殊表现与规律机制,随着同心筒破水发射等特殊应用的出现,环形喷口气体射流/泡流的基础现象观测和机制分析成为迫切的需求. 基于环形喷管的设计和水下射流条件的分析,设计建立了一套环形喷管水箱实验系统,对水下环形喷管喷口气泡发展演化过程进行了初步的实验研究. 为观测研究气体通过环形喷管气泡生长发展过程,在较低压力、较低流速下,采用高速摄影仪记录气泡生长及发展演化过程. 结合对气泡发展演化过程的图像处理与分析,研究分析了环形喷口气泡形成区制、气泡生长过程形态发展特点、以及气泡形成时间及气泡体积变化特点. 研究表明:在本实验气体流量范围内(50.8~237.3 dm3/min),环形喷口气泡发展演化过程呈现较为明显的三周期区制,前泡尾流影响是环形气泡呈三周期区制的主要原因;不同周期内的气泡形成时间具有较稳定规律,并受到流量影响;气泡生长过程中有较为明显的下沉、回升特征;气泡表面张力、液体惯性与流动的共同作用,造成了典型的气泡顶部坍塌现象.      

Measurement of very small liquid flows

A measuring principle for the flow rate of liquid follows consists in the determination of the volume change of a liquid in a tank in relation to unit of time. The development and the realization of three measurement systems based on this principle are presented in this paper. The devices can measure liquid flows below 0.2 L/h. One flow meter uses an air bubble in the form of a stopper as tracer. A special design keeps the bubble in the measuring tube; it does not have to be replaced. Another flow meter measures the volume changes by determining the pressure at the bottom of a vertical tube. To achieve a continuous operation, a differential design with two corresponding tubes was realized. The third flow meter measures the mass of a drop at the end of a horizontal silicone tube working as a bending beam. The liquid flows through the tube and is forced to form drops at its end. Owing to their design, each of the three devices has distinctive characteristics. A theory of measurement systems that facilitates synthesis and analysis of measuring devices serves as the basis for the development of the flow meters.     

Four-way coupled Eulerian–Lagrangian Direct Numerical Simulations in a vertical laminar channel flow

Direct Numerical Simulations of a laminar two-phase flow into a vertical channel are investigated. An Eulerian–Lagrangian approach allows tracking each bubble position with a four-way coupling strategy, i.e. taking into account bubble-fluid and bubble-bubble interactions. The flow configuration has been chosen to highlight the buoyancy effects due to significant values of void fraction (high numbers of bubbles); hence the bubbles collisions and wall effects are the critical parameters to ensure the dispersion of the bubble plume. The DNS approach is self-consistent and does not rely on closure relations or empirical correlations for describing the collective bubble dynamics. It is found that the DNS predicts well the behavior of the bubble plume and its back effect on the liquid phase when compared with a mixture model and experimental data. The elastic nature of collisions, the sensitivity of the mean and RMS values of velocities and void fraction to the mesh quality are explored.     

Turbulent flow past a bubble and an ellipsoid using shadow-image and PIV techniques

An experimental investigation on flow around an oscillating bubble and solid ellipsoid with a flat bottom was conducted. A single air bubble (equivalent diameter D_e=9.12 mm) was attached to a small disk (1 mm) at the end of a needle and suspended across a vertical square channel (100 mm) by wire wherein water flowed downward at a constant flowrate. The solid ellipsoid (D_e9.1 mm) was suspended across the square channel in the same manner. The equivalent diameter-based Reynolds and Eotvos number range, 1950<Re<2250 and 11<Eo<11.5, placed the bubble in the ‘wobbly’ regime while the flow in its wake was turbulent. A constant flowrate and one bubble size was used such that flow in the wake was turbulent. Velocity measurements of the flow field around the bubble or solid were made using a one CCD camera Digital Particle Image Velocimetry (DPIV) system enhanced by Laser Induced Fluorescence (LIF). The shape of the bubble or solid was simultaneously recorded along with the velocity using a second CCD camera and an Infrared Shadow Technique (IST). In this way both the flow-field and the boundary of the bubble (solid) were measured. The velocity vector plots of flow around and in the wake of a bubble/solid, supplemented by profiles and contours of the average and root-mean-square velocities, vorticity, Reynolds stress and turbulent kinetic energy, revealed differences in the wake flow structure behind a bubble and solid. One of the significant differences was in the inherent, oscillatory motion of the bubble which not only produced vorticity in the near-wake, but as a result of apparent vorticity stretching distributed the turbulent kinetic energy associated with this flow more uniformly on its wake, in contrast to the solid.     

Nucleate pool boiling in microgravity: Recent progress and future prospects

Pool boiling on flat plates in microgravity has been studied for more than 50 years. The results of recent experiments performed in sounding rocket are presented and compared to previous results. At low heat flux, the vertical oscillatory motion of the primary bubble is responsible for the increase in the heat transfer coefficient in microgravity compared to ground experiments. The effect of a non-condensable gas on the stabilisation of the large primary bubble on the heater is pointed out. Experiments on isolated bubbles are also performed on ground and in parabolic flight. The effect of a shear flow on the bubble detachment is highlighted. A force balance model allows determining an expression of the capillary force and of the drag force acting on the bubble.     

Measurement of bubble size, velocity and concentration in flashing flow behind a sudden constriction

In the present paper the results of investigations in flashing flow behind a sudden constriction in vertical upflow are described. Flow visualization, laser-Doppler and phase-Doppler anemometry have been used to measure local bubble and fluid velocities, local bubble sizes and void fractions. The measurements were performed in the midplane of a two-dimensional channel with a 2:1 stepwise constriction.It was found that bubble nucleation takes place in the recirculation zone immediately behind the constriction, which is the location of the lowest static pressure. These bubbles are transported downstream by the mean flow field, while undergoing further growth. No additional nucleation was observed downstream of the recirculation zone. A periodic, cloudwise behaviour of the bubble formation was found which could be explained by the interaction between the bubble growth and the mean flow field. This interaction results in strong disturbances of the mean flow field, which show up as an increase of the fluctuating bubble velocity by a factor of 3 compared to single-phase measurements in a region of 10 step heights behind the constriction. However, these fluctuations appear more like a periodic change in the mean velocity rather than a higher turbulence level. The measured arithmetic mean bubble diameters rise from approx. 50 μm in the recirculation region to about 70–80 μm 50 step heights downstream. Maximum local bubble number density and void fraction were found to be 160001/cm³ and 0.8%, respectively.     

On the motion of long bubbles in vertical tubes

Potential flow theory has been applied to study the shape and speed of an infinitely long bubble rising through flowing liquid in a vertical tube. In particular, the combined effects of surface tension and externally forced liquid motion are examined. An analytical formula for the bubble rise velocity in stagnant liquid is proposed, and shown to be in good agreement with experimental data for all values of surface tension. Numerical solutions for the bubble velocity in upward flowing liquid are obtained for laminar and turbulent velocity profiles. Approximate expressions for the bubble velocity, where the effects of liquid motion and surface tension are incorporated through the Reynolds and inverse Eötwos, are proposed and compared with experimental data. The predicted changes in bubble shape have, to a large extent, been confirmed through comparisons with photographic evidence for a wide range of parameters.