三维气泡与自由表面相互作用的直接数值模拟

采用VOF中的PLIC界面重构方法数值模拟了三维气泡在液流中上升并与自由表面相互作用的运动.分别考察了不同初始高度,有无来流及有无再生气泡对气泡上升高度、上升速度、压力及与自由表面相互作用等的影响.结果表明:气泡初始位置越低,顶端上升的高度越大,自由面隆起的范围更广.越靠近自由表面,底部射流横向发展越窄,而向上的压力梯度,气泡上升速度,底部射流上升高度越大,反之则反;但如果底部射流均在接近自由表面以前已横向发展充分,则差别不大.气泡外形、上升高度、破裂时间以及上升速度与来流无关.产生再生气泡后,原生气泡与再生气泡相吸,相互加速对方的上升;自由表面抬升的高度增幅较大,范围拓宽,上升速度也大大增加,且再生气泡越多,自由表面隆起的范围越大.     

含气泡油滴撞击油膜壁面时气泡的变形与破裂

油--气润滑过程中润滑油液滴受高速气流扰动易形成含气泡油滴,微气泡将对油滴撞击壁面时的运动过程以及壁面油膜 层的形成质量产生重要影响. 基于耦合的水平集--体积分数 方法,对含气泡油滴撞击油膜壁面行为进行数值模拟研究, 考察含气泡油滴撞击油膜壁面时气泡的变形运动过程,探讨气泡破裂的动力学机制,分析气泡大小、碰撞速度和液体黏度等因素对含气 泡油滴撞壁过程中气泡变形特征参数的影响规律. 研究表明:含气泡油滴撞击油膜壁面后气泡会发生变形,并破裂形成膜液滴;气泡随同 液滴运动过程中,气泡内外压力和速度梯度变化是使气泡发生破裂的主要诱因. 气泡大小对气泡破裂方式影响较大,气泡较小时发生单 点破裂,而气泡较大时更容易发生多处破裂. 不同大小气泡受力差异较大,气泡大小与破裂发生时刻没有明显相关性. 碰撞速度和液体 黏度对气泡的变形、破裂和破裂发生时刻都具有一定的影响. 碰撞速度越大,油滴动能越大,更容易产生气泡变形和破裂现象. 液体黏 度增大,在油滴撞壁运动前期促进气泡变形,而在运动后期可以阻延气泡破裂行为发生.      

Wake properties of a single gas bubble in three-dimensional liquid-solid fluidized bed

Experiments were performed to investigate the wake properties of a single gas bubble in a three-dimensional liquid-solid fluidized bed via a video camera moving at the same speed as the bubble. The solids holdup in the fluidized bed varied up to around 10%. The bubble size varied from 5 to 20 mm with corresponding bubble Reynolds numbers ranging from 1000 to 6500. The bubble was observed to have two types of wake configurations depending on the bubble size: the asymmetric/helical vortex wake for small bubbles and the symmetric wake for large bubbles. The bubble shape and relative rise velocity in the fluidized bed can be well-represented by correlations developed for single bubbles in liquid media, although the bubble shape in liquid-solid media is slightly more flattened compared to that in liquid media. The bubble rocking frequency was found to be independent of particle properties and to correspond in magnitude to the vortex shedding frequency in a two-dimensional liquid-solid fluidized bed. The average primary wake size in three dimensions is comparable to that in two dimensions.     

壁面约束对裙带气泡动力学的影响

基于流体体积法(volume of fluid,VOF),数值模拟了装满黏性液体的圆柱形汽缸中的裙带气泡的浮升运动,研究了侧壁面约束对裙带气泡浮升动力学的影响.用雷诺数(Re)、韦伯数(We)、长宽比(χ)、裙带厚度(T/d)和裙带长度(L/d)等参数来表征不同约束比条件下(1.1≤Cr≤10)裙带气泡的运动和变形特性,分别在全局参考系和局部参考系下分析了壁面对气泡内外流场的影响.模拟结果显示,当Cr≥8时,裙带气泡的行为特性与在无界流域条件下的情况相当,可视作壁面无关的.当Cr8时,壁面对裙带气泡的浮升速度和形状演化有显著影响.随着壁面的靠近,裙带气泡受到的阻力增大,造成浮升速度下降.约束比降低使裙带厚度增厚而长度变短直至裙带消失,裙带气泡受挤压而被拉长并逐渐变为椭圆球帽形最后到子弹形.相反,约束比增大时,裙带气泡尾流效应增强,气泡边缘处流场产生明显的循环流动(涡环),促使裙带的形成.研究表明壁面会加剧裙带气泡产生破碎,印证了前人的推断.模拟结果与已有的经验公式吻合良好,分析了前人公式的适用性.     

电场作用下气泡上升行为特性的数值计算研究

利用电场控制气泡形态及运动,强化气液相间传热传质是电流体动力学的重要研究内容之一. 然而目前多数研究集中在非电场下的气泡动力学上,对于电场下的气泡行为特性及电场的作用机制仍需开展深入研究. 本研究对电场作用下单个气泡在流体中上升过程的动力学行为进行了数值模拟研究. 在建立二维模型的基础上求解电场方程与Navier-Stokes方程,并采用水平集方法捕捉了上升气泡的位置及形状. 模拟结果的准确性与有效性通过与前人实验和数值结果进行对比得到了验证. 通过改变雷诺数、邦德数和电邦德数等不同参数研究了电场下液体黏度、表面张力和电场力对气泡运动变形的影响. 计算结果表明,电场对气泡的动态特性有显著影响. 非电场情况下液体黏度和表面张力较大时气泡基本维持球状,反之气泡发生变形并逐步达到稳定状态. 此外,电场作用使气泡在初始上升阶段发生剧烈形变,随着不断上升,气泡形变程度不断减小,且气泡的上升速度和长径比均出现振荡. 垂直电场使气泡的上升速度有较大的提高,且随着电邦德数的增大,难以达到相对稳定的状态.      

可压缩流场中气泡脉动数值模拟

在应用边界元方法对气泡动力学的研究中, 绝大多数模型是建立在不压缩势流理论基础之上, 针对可压缩流场中气泡运动特性的研究很少. 从波动方程出发, 分别在气泡运动前期和后期对波动方程进行简化, 得到气泡运动局部和全局简化方程, 采用双渐进方法对简化方程进行匹配, 提出了考虑流场可压缩性的非球状气泡运动模型. 该模型的计算结果与Prospertti 等的解析结果吻合很好, 气泡脉动最大半径和内部最大压力随气泡脉动逐渐减小. 基于该模型对比了自由场中药包爆炸考虑可压缩性与不考虑可压缩性的计算结果, 发现考虑可压缩性气泡射流速度较小, 随后基于该模型计算了刚性边界下气泡的运动特性.     

On the motion of long bubbles in vertical tubes

Potential flow theory has been applied to study the shape and speed of an infinitely long bubble rising through flowing liquid in a vertical tube. In particular, the combined effects of surface tension and externally forced liquid motion are examined. An analytical formula for the bubble rise velocity in stagnant liquid is proposed, and shown to be in good agreement with experimental data for all values of surface tension. Numerical solutions for the bubble velocity in upward flowing liquid are obtained for laminar and turbulent velocity profiles. Approximate expressions for the bubble velocity, where the effects of liquid motion and surface tension are incorporated through the Reynolds and inverse Eötwos, are proposed and compared with experimental data. The predicted changes in bubble shape have, to a large extent, been confirmed through comparisons with photographic evidence for a wide range of parameters.     

Ellipsoidal model of the rise of a Taylor bubble in a round tube

The rise velocity of long gas bubbles (Taylor bubbles) in round tubes is modeled by an ovary ellipsoidal cap bubble rising in an irrotational flow of a viscous liquid. The analysis leads to an expression for the rise velocity which depends on the aspect ratio of the model ellipsoid and the Reynolds and Eötvös numbers. The aspect ratio of the best ellipsoid is selected to give the same rise velocity as the Taylor bubble at given values of the Eötvös and Reynolds numbers. The analysis leads to a prediction of the shape of the ovary ellipsoid which rises with same velocity as the Taylor bubble.     

竖直流道宽度对气泡运动行为影响的数值模拟

用数值方法模拟了竖直通道宽度对气泡在液体中的非定常运动、变形以及传热特性的影响。在这个模拟中,界面跟踪采用了VOF方法,并采用PL IC进行界面重构。主流场计算采用有限容积方法将控制方程离散,其中扩散项采用中心差分格式,对流项采用一阶迎风格式。用成熟的S IM PLE算法求解N-S方程的速度与压力的耦合问题。引入CSF模型处理运动界面的表面张力。利用所编制的程序计算了竖直流道中的单个气泡的形状、运动特性以及气泡内外流场与传热特性,并对竖直通道宽度在不同情况下,对气泡的形状、运动特性以及传热特性进行了进一步的研究。得到了一系列有价值的结果,并与实验结果比较。表明数值模拟结果与实验结果吻合的较好。     

BUBBLE CHARACTERISTICS IN A TWO-DIMENSIONAL VERTICALLY VIBRO-FLUIDIZED BED

Measurement of bubble size and local average bubble rise velocity was carried out in a vertically sinusoidal vibro-fluidized bed. Glass beads of Geldart group B particles were fluidized at different gas velocities, while the bed was vibrated at different frequencies and amplitudes to study their effects on the bubble behavior. This is compared with the case of no vibration in a two-dimensional bed and it is concluded that with vibration the local average bubble size, dbav, decreases significantly, especially at minimum bubbling velocity. The average bubble size increases slightly with increasing vibration frequency and amplitude. The local average bubble rise velocity is higher than that with no vibration, though with increasing vibration frequency and amplitude, it does not change significantly.     

Pressure-oscillation defoaming for viscoelastic fluid

The enhancement of bubble rising velocity was experimentally investigated by mechanically applying an oscillating pressure to a single small air bubble (e.g., 1 mm³) in a viscoelastic fluid. For shear-thinning fluids, the cyclic change in bubble diameter induced by the oscillating pressure generates a continuous strong local flow near the bubble surface. Consequently, the apparent liquid viscosity is reduced and the bubble rising velocity increases by 400 times or more compared to the case without oscillating pressure. However, for a Newtonian fluid, almost no effect was observed with oscillating pressure. Time-series data of the longitudinal and horizontal bubble diameters were obtained experimentally using a stroboscope and a video system, and these data were used to estimate the local shear rate and the local shear viscosity. The increase in bubble rising velocity estimated from the shear viscosity behavior agreed well with the experimental data. Additionally, a periodic change in the bubble shape from a sphere at the maximum bubble size to a cusped shape at the minimum bubble size was observed under strong oscillatory pressure.     

浮力气泡对水平壁面的回弹动力学特性

黏性液体中的气泡浮升运动有趣而又复杂,而气泡与固壁边界的相互作用更是广泛存在于实际工程中.基于轴对称数值计算,模拟了浮力驱动下气泡在黏性液体中上升并与顶部水平固壁面碰撞、回弹的过程.采用考虑表面张力的不可压、变密度Navier-Stokes方程来描述气液两相流流动,并通过基于分级八叉树的有限体积法进行数值求解.为准确捕捉气泡在回弹过程中局部而迅速的拓扑变化,采用了动态自适应网格技术耦合流体体积法(volume of fluid,VOF)来重构气泡的形状. 从气泡对壁面的碰撞和回弹的基本现象入手,研究了伽利略数 Ga和接触速度$U_{a}$对气泡回弹动力学特性的影响, 分析了气泡碰撞过程中涡结构的变化.用回弹高度$H$、回弹周期$T$、长宽比{$A_{r}$}、浮升速度$U$、轴向位置$z$和回复系数$C_{r}$等参数来表征不同条件时气泡的运动和形状特性. 研究结果表明,气泡的回弹运动特性对 Ga十分敏感. Ga的增大可加剧气泡形变, 促进气泡的回弹运动, 增多回弹次数,增大回弹参数($T$和$H)$, 提升回复系数. 然而,接触速度并非决定气泡回弹动力学的控制参数, $U_{a}$的改变并不会改变回复系数.      

Disengagement of the gas phase in bubble columns

The technique of gas disengagement is popularly used to assess the bubble size distribution in bubble columns. The technique involves the dynamic measurement of dispersion height when the gas supply is stopped. In this paper a mathematical model has been proposed for the process of dynamic gas disengagement. It has been shown that the initial faster disengagement is due to the presence of internal liquid circulation and not due to the presence of very large bubbles. Further, slower disengagement has been attributed to the transition from heterogeneous dispersion to homogeneous dispersion. The new model also explains the effects of superficial gas velocity, column diameter, column height and liquid phase physical properties on the gas disengagement.     

Benchmark computations of diffuse interface models for two‐dimensional bubble dynamics

Diffuse interface models for incompressible two‐phase flow with large density ratios are tested on benchmark configurations for a two‐dimensional bubble rising in liquid columns. The benchmark quantities circularity, center of mass, and mean rise velocity are compared with reference solutions from Hysing et al. Copyright © 2011 John Wiley & Sons, Ltd.     

Level set method for numerical simulation of a cavitation bubble,its growth,collapse and rebound near a rigid wall

A level set method of non-uniform grids is used to simulate the whole evolution of a cavitation bubble, including its growth, collapse and rebound near a rigid wall. Single-phase Navier–Stokes equation in the liquid region is solved by MAC projection algorithm combined with second-order ENO scheme for the advection terms. The moving interface is captured by the level set function, and the interface velocity is resolved by “one-side” velocity extension from the liquid region to the bubble region, complementing the second-order weighted least squares method across the interface and projection inside bubble. The use of non-uniform grid overcomes the difficulty caused by the large computational domain and very small bubble size. The computation is very stable without suffering from large flow-field gradients, and the results are in good agreements with other studies. The bubble interface kinematics, dynamics and its effect on the wall are highlighted, which shows that the code can effectively capture the “shock wave”-like pressure and velocity at jet impact, toroidal bubble, and complicated pressure structure with peak, plateau and valley in the later stage of bubble oscillating. The project supported by the National Natural Science Foundation of China (10272032 and 10672043). The English text was polished by Keren Wang.     

水平刚性面下方水下爆炸气泡垂向运动的理论研究

为了研究边界面对水下爆炸气泡脉动的影响,根据势流理论建立了水平刚性面下方在浮力作用下作垂向运动的水下爆炸气泡的理论模型,编制计算程序进行求解。对水下爆炸气泡脉动运动的特点、流场的速度和压力的分布、气泡引起的载荷形式进行了分析。结果表明此模型能够反映水下爆炸气泡和周围流体介质的运动规律,并能进行定量的计算。     

On the modeling and simulation of a laser‐induced cavitation bubble

Single cavitation bubbles exhibit severe modeling and simulation difficulties. This is due to the small scales of time and space as well as due to the involvement of different phenomena in the dynamics of the bubble. For example, the compressibility, phase transition, and the existence of a noncondensable gas inside the bubble have strong effects on the dynamics of the bubble. Moreover, the collapse of the bubble involves the occurrence of critical conditions for the pressure and temperature. This adds extra difficulties to the choice of equations of state. Even though several models and simulations have been used to study the dynamics of the cavitation bubbles, many details are still not clearly accounted for. Here, we present a numerical investigation for the collapse and rebound of a laser‐induced cavitation bubble in liquid water. The compressibility of the liquid and vapor are involved. In addition, great focus is devoted to study the effects of phase transition and the existence of a noncondensable gas on the dynamics of the collapsing bubble. If the bubble contains vapor only, we use the six‐equation model for two‐phase flows that was modified in our previous work [A. Zein, M. Hantke, and G. Warnecke, J. Comput. Phys., 229(8):2964‐2998, 2010]. This model is an extension to the six‐equation model with a single velocity of Kapila et al. (Phys. Fluid, 13:3002‐3024, 2001) taking into account the heat and mass transfer. To study the effect of a noncondensable gas inside the bubble, we add a third phase to the original model. In this case, the phase transition is considered only at interfaces that separate the liquid and its vapor. The stiffened gas equations of state are used as closure relations. We use our own method to determine the parameters to obtain reasonable equations of state for a wide range of temperatures and make them suitable for the phase transition effects. We compare our results with experimental ones. Also our results confirm some expected physical phenomena. Copyright © 2013 John Wiley & Sons, Ltd.     

水平均流中细管排放气泡的三维数值模拟

在液体为无粘不可压，流动有势和气体遵循完全气体绝热关系的假定下，本文应用边界积分方程方法数值模拟了水平均流中垂直细管排放气泡的三维动力学问题，边界采用高阶有限元表达。文中介绍了有关泡面法向矢量、切向速度、曲率和接触线等的计算技术。与已知解的比较，表明了这一数值方法的高精度和优越性。算例显示了水平均流对于气泡形状和体积的影响     

Ellipsoidal Oscillations of a Gas Bubble with Periodic Variation of the Surrounding Fluid Pressure

Ellipsoidal linear and nonlinear oscillations of a gas bubble under harmonic variation of the surrounding fluid pressure are studied. The system is considered under conditions in which periodic sonoluminescence of the individual bubble in a standing acoustic wave is observable. A mathematical model of the bubble dynamics is suggested; in this model, the variation of the gas/fluid interface shape is described correct to the square of the amplitude of the deformation of the spherical shape of the bubble. The character of the air bubble oscillations in water is investigated in relation to the initial bubble radius and the fluid pressure variation amplitude. It is shown that nonspherical oscillations of limited amplitude can occur outside the range of linearly stable spherical oscillations. In this case, both oscillations with a period equal to one or two periods of the fluid pressure variation and aperiodic oscillations can be observed.     

利用格子Boltzmann方法模拟单个气泡在复杂流道内的运动特性

利用格子Boltzmann方法模拟了单个气泡在具有三个半圆形喉部的复杂流道内的上升过程.通过分析气泡运动过程中的形态、运动轨迹及运动速度的变化,研究复杂流道对气泡运动特性的影响.研究结果表明,在上升过程中,由于壁面的影响,气泡的形状发生严重的变形,运动轨迹也发生相应的偏转.通过实验结果的对比,验证了模拟结果的正确性.结果表明格子Boltzmann方法可以用于模拟具有复杂边界的两相流问题.