含切口损伤复合材料层合板拉伸失效行为研究

对含有不同切口损伤的复合材料层合板试件进行了拉伸试验,采用电阻应变计同步测量切口损伤前缘区域随载荷的变化,测定含切口损伤层合板的剩余强度,并讨论了损伤长度和损伤角度对剩余强度的影响规律.建立含切口损伤复合材料层合板有限元模型,分析了含切口损伤复合材料层合板的拉伸失效行为,计算了含切口损伤复合材料层合板的剩余强度,确定了剩余强度与切口损伤状态的关系.计算结果与试验结果具有较好的一致性.     

含孔复合材料层合板静拉伸损伤演化的实验和表征方法

为了深入探究复合材料层合板结构的损伤机理和损伤演化,应用声发射技术和图像相关技术同步实时监测含孔碳纤维复合材料层合板试样在静拉伸过程中的损伤演化。实验结果表明,试样表面应变场呈现局部化特征。对应变集中带在加载方向的应变值进行了统计分析,获得了应变场的特征统计量(标准差)随加载的演化模型。层合板损伤时产生声发射信号的峰值频率大小能够有效区分复合材料的损伤模式,由此,建立了基于损伤模式累积声发射数的损伤演化模型。通过对应变场演化模型和声发射损伤演化模型的分析,可以将复合材料的损伤演化分为损伤初始阶段、损伤平稳扩展期、损伤严重阶段三个部分。统计分析结果表明:在损伤严重阶段,基于声发射事件数的各种损伤的损伤变量和局部应变场标准差快速增长,因此局部应变场统计标准差可以作为后期局部损伤严重程度的识别指标。     

复合材料层合板冲击损伤及剩余强度分析方法

应用三维逐渐累积损伤理论和分析技术对层合板的冲击及冲击后含损伤的层合板在拉伸载荷下损伤扩展的全过程进行分析.分析中取消了以往研究者对冲击后层合板损伤状态所做的人为假设,将冲击后层合板的实际损伤状态直接用于剩余拉伸强度研究.通过与已有文献结果比较,验证了方法的正确性.     

含分层损伤复合材料层合板剩余压缩强度研究

准确预测含分层损伤层合板的剩余压缩强度,对复合材料具有十分重要 意义。本文基于层合板一阶剪切理论,建立了一种考虑复合材料多种损伤的含分层层合板刚度退化模型,通过数值算例分析了分层屈曲临界载荷与材料强度极限的关系以及刚度退化对含分层层合板前后屈曲行为的影响。     

含分层损伤复合材料层合板的压缩强度研究

给出了基于一阶剪切变形理论的含分层损伤层合板有限元分析模型,将含分层损伤层合板在压缩载荷作用下的强度破坏分析和屈曲破坏分析统一起来,先区分其破坏形式,然后再进行具体破坏分析.在屈曲特性分析中考虑了铺层强度破坏引起的刚度折减的影响.数值结果表明, 该文给出的方法和结论对含分层损伤复合材料层合板的设计更具参考价值.     

三维编织复合材料渐进损伤的非线性数值分析

基于考虑纤维束相互挤压的八边形纤维束截面单胞模型,引入周期性位移边界条件,采用 细观非线性有限元方法,建立了三维四向编织复合材料的渐进损伤拉伸强度模型. 该模型考 虑了增强体纤维束纵向非线性剪切应力-应变关系,采用Hashin型损伤失效准则定义了纤维 束的典型损伤类型,并根据纤维束和纯基体相应损伤类型所造成的材料性能退化,模拟了不 同编织角试件各类损伤产生、扩展及材料最终破坏的整个过程. 模型数值结果与实验数据吻 合较好,证明了该模型的合理有效性. 探讨了组分材料剪切非线性、损伤对材料宏观非线性 本构行为的影响,结果表明：随着编织角增大,纤维束剪切非线性效应和累积损伤对材料非 线性力学行为的影响明显增强.     

含缺口复合材料层合板的三维有限元失效分析

本文研究了复合材料层合板最终强度计算的有限元理论,讨论了修正的Newton-Raphson迭代方法在层合板失效过程中应力场计算的迭代过程.同时本文建立了带缺口的复合材料层合板三维有限元模型,充分考虑层合板的纤维断裂、基体开裂和分层三种失效模式,采用修正的三维Hashin准则作为失效判断的依据,计算了三种不同铺层的层合板最终失效载荷值,与试验值吻合得很好.鉴于层压板材料常数ν23的数值难于测定的特点,讨论其对最终失效载荷的影响.在三维有限元模型的基础上,实现了失效扩展仿真分析.     

开孔复合材料层合板强度不确定性分析

以拉伸载荷作用下AS4/3501-6开孔复合材料层合板为研究对象,采用考虑复合材料层合板就地强度效应的有限断裂力学模型和基于方差的敏感性测度分析模型相结合的方法,研究单层板宏观力学性能不确定性对具有不同孔径和铺层顺序的开孔复合材料层合板破坏强度的影响．研究结果表明：单层板力学性能对开孔板强度影响程度的大小与孔径相关,但敏感性排序与孔径无关．同时,单层板力学性能敏感性测度与层合板铺层顺序有关,层合板各向异性比越大,开孔板拉伸破坏受单层板纤维方向拉伸强度的影响越大,而且开孔板拉伸强度与单层板纤维方向拉伸强度呈正相关,与横向弹性模量呈负相关,与面内剪切模量和纵向弹性模量不具有单调关系．     

静应力作用下的层合板接头损伤失效分析

基于单层板理论,结合有限元分析技术即应力分析、Hashin三维失效判定准则、包含4种基本损伤类型相互关联作用的材料性能退化方法及结构最终破坏判据等,建立了含辅助铺层层合板接头静载损伤失效分析方法. 同时,对层合板接头损伤扩展进行了模拟分析,损伤计算结果与试验分级加载试样X光进行了对比. 通过多种类型层合板接头静强度预测结果与试验结果对比及静载累积损伤规律分析表明,建立的静载三维累积损伤分析的强度预测方法可方便模拟不同结构尺寸层合板接头内部各铺层损伤起始、发展及结构最终破坏整个累积过程,同时获得其最终破坏强度及破坏模式. 该方法的预测结果与试验结果吻合较好.      

含圆孔复合材料层板在拉伸载荷下损伤破坏过程的模拟

本文应用有限元法模拟受拉含孔夏合材料层板损伤起始、累积直至破坏的过程。在模拟中引入了作者早些时建立的包含基体开裂层非对称约束影响的损伤本构关系，以及裂纹密度与损伤区应力关系函数等。本文给出损伤累积模拟方法并编制了程序，用该程序可以获得层板加载过程中各层的损伤状态、计算其刚度衰减和应力重分布以及最终破坏载荷。给出了数值模拟算例并与现有研究结果进行了比较。     

Nonlinear progressive damage model for composite laminates used for low-velocity impact

In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impact is presented. Being applied to three-dimensional （3D） solid elements and cohesive elements, the nonlinear damage model can be used to analyze the dynamic performance of composite structure and its failure be- havior. For the intralaminar damage, as a function of the energy release rate, the damage model in an exponential function can describe progressive development of the damage. For the interlaminar damage, the damage evolution is described by the framework of the continuum mechanics through cohesive elements. Coding the user subroutine VUMAT of the finite element software ABAQUS/Explicit, the model is applied to an example, i.e., carbon fiber reinforced epoxy composite laminates under low-velocity impact. It is shown that the prediction of damage and deformation agrees well with the experimental results.     

三维编织复合材料渐进损伤的非线性模型及强度分析

建立了考虑周期性位移边界条件的细观体胞模型,对三维编织复合材料的渐进损伤过程进行数值模拟。采用Eshelby-Mori—Tanaka方法计算含损伤裂纹的材料的剐度矩阵,并将有限元网格尺寸和单元裂纹尺寸引入损伤演化方程,有效地降低了模拟结果对有限元网格的依赖程度。通过计算得到了材料应力应变的非线性关系和失效时的极限强度,并分析了材料的破坏机理。结果表明,大编织角材料的破坏模式主要是基体失效与纤维横向拉剪破坏,模拟计算结果与文献中的实验值吻合较好。     

Fracture of composite laminates containing cracks due to shear loading

The responses of graphite/epoxy [0/90/±45] _s , [±45]_2s , [0/90]_2s and [0/±45]_2s composite laminates with and without center cracks were studied under shear loading using the three-rail shear test. The shear stress/strain relationship, the failure mechanisms and the notched strength were analyzed. Substantial amounts of local buckling were observed in some of the laminates. The present paper shows that shear modulus can be determined accurately using the three-rail shear test with proper interpretation of data. Using the minimum strength model, only one characteristic length was needed to predict accurately the notched strength of a composite laminate under shear and tensile loadings.Paper was presented at the 1987 SEM Spring Conference on Experimental Mechanics held in Houston, TX on June 14–19.     

Cohesive modeling of transverse cracking in laminates under in-plane loading with a single layer of elements per ply

This study aims to bridge the gap between classical understanding of transverse cracking in cross-ply laminates and recent computational methods for the modeling of progressive laminate failure. Specifically, the study investigates under what conditions a finite element model with cohesive X-FEM cracks can reproduce the in situ effect for the ply strength. It is shown that it is possible to do so with a single element across the thickness of the ply, provided that the interface stiffness is properly selected. The optimal value for this interface stiffness is derived with an analytical shear lag model. It is also shown that, when the appropriate statistical variation of properties has been applied, models with a single element through the thickness of a ply can predict the density of transverse matrix cracks.     

复合材料损伤容限分析软件CDTAC 1．0版简介

本文简要地介绍了由飞机强度研究所研制的复合材料损伤容限分析软件CDTAC1．0版本的各项基本功能,及其所用的基本理论和程序结构,并给出典型算例。     

横向爆炸载荷下开孔板的动应力集中因子

基于ANSYS 5.7/LS-DYNA程序,对3 m3 m0.25 m四边固支和简支、中心具有0.3 m0.3 m方孔的开孔板和无孔板对应点在两种下三角爆炸载荷作用下的应力响应进行了分析;由开孔板和无孔板边对应点的主应力时程曲线,对提出的能量密度时间分布函数的绝对值平方进行变上限积分,按其比值确定动应力集中因子,该方法简单易行。     

On the description of anisotropic damage in composite laminates

A general anisotropic damage theory of cracked laminates is formulated here. The deformation of composite laminates is composed of matrix elastic strains, pseudo-elastic damage strains due to cracking and permanent damage strains due to interlaminar slip. The surface of damage initiation is constructed according to the concept of linear elastic fracture mechanics for the virgin material. After the initial damage, a pesudo-elastic damage can be used to describe the damage behaviour if interlaminar slip is negligible. Damage evolution, load induced anisotropy and interlaminar intralaminar interaction for composite laminates are examined; the latter can perturb the normality structure of damage strain rate. Explicit expressions are given for pseudo-elastic (or secant) moduli of the damaging composite laminates, under a non-interacting assumption imposed on the cracks between different families.     

三维五向编织复合材料渐进损伤分析及强度预测

基于五向编织复合材料连续体细观结构单胞,提出了材料的三维渐进损伤分析模型,采用非线性有限元方法并结合均匀化平均思想,建立了三维五向编织复合材料的强度预测胞元模型.经研究典型编织角材料在拉伸载荷作用下细观损伤的发生及演化过程,分析了材料的细观失效机理,获得了材料的宏观拉伸应力应变曲线和极限破坏强度,并详细探讨了工艺参数编织角对材料宏观力学性能的影响规律.     

Dynamic modeling of a revolute-prismatic flexible robot arm fabricated from advanced composite materials

A dynamic model for a two degree-of-freedom planar robot arm is derived in this study. The links of the arm, connected to prismatic and revolute joints, are considered to be flexible. They are assumed to be fabricated from either aluminum or laminated composite materials. The model is derived based on the Timoshenko beam theory in order to account for the rotary inertia and shear deformation. These effects are significant in modeling flexible links connected to prismatic joints. The deflections of the links are approximated by using a shear-deformable beam finite element. Hamilton's principle is implemented to derive the equations describing the combined rigid and flexible motions of the arm. The resulting equations are coupled and highly nonlinear. In view of the large number of equations involved and their geometric nonlinearity (topological and quadratic), the solution of the equations of motion is obtained numerically by using a stiff integrator.The digital simulation studies examine the interaction between the flexible and the rigid body motions of the robot arm, investigate the improvement in the accuracy of the model by considering the flexibility of all rather than some of the links of the arm, assess the significance of the rotary inertia and shear deformation, and illustrate the advantages of using advanced composites in the structural design of robotic manipulators.