结构振动的滑模变结构半主动控制

研究应用磁流变阻尼器(MRD)对结构振动半主动控制的算法和原理。研制并对磁流变阻尼器进行了阻尼特性实验，采用非线性滞回双粘性模型描述磁流变阻尼器的阻尼特性，模型结果与实验结果非常一致。采用滑模控制算法和趋近律方法设计了半主动控制器。利用滑模控制方法所建立的控制器，本文给出了地震激励下结构振动半主动控制算例。计算分析表明，半主动滑模控制具有控制效果明显、鲁棒性好等优点，是一种非常有发展前途的控制方法。     

斜拉索振动的模糊半主动控制研究

考虑拉索垂度及抗弯刚度的影响,得出了索-阻尼器系统振动偏微分方程;用中心差分法将偏微分方程在空间内离散,导出了系统的面内振动常微分方程组;提出了使用MR阻尼器(Magnetorheological Damper)作为控制设备,模糊集为基础的半主动控制算法,并运用提出的算法对索-阻尼器系统进行了振动控制分析。本文方法的优势在于算法自身的鲁棒性、处理非线性问题的能力强和不需要结构的精确数学模型,算法需要的输入变量少,可以解决实际工程中斜拉索的振动响应信息难以测量的困难。模糊算法的输出直接控制MR阻尼器的输入电压。与LQR-Clipped算法不同,MR阻尼器的输入电压可以是零与最大值之间的任意值。本文以实际斜拉桥拉索为例,分析了拉索的振动控制效果,结果表明本文提出的模糊半主动控制算法,使MR阻尼器的功能得到了更好的发挥,比MR被动控制效果好,且可以减小控制力。     

A NEW STOCHASTIC OPTIMAL CONTROL STRATEGY FOR HYSTERETIC MR DAMPERS

I. INTRODUCTION Magneto-rheological (MR) ?uid as a smart material possesses fairly good essential characteristics suchas reversible change between liquid and semi-solid in milliseconds with a controllable yield strengthwhen exposed to a magnetic ?eld. A…     

一类非线性磁流变系统局部分岔特性研究

讨论了一类基于磁流变阻尼器非线性系统的局部分岔与控制问题，建立了该系统的动力 学模型，运用中心流形定理和范式理论，得到该系统双零特征值问题的规范形及其普适开折， 进而探讨了此系统的分岔行为和稳定性；给出了分岔曲线、转迁集；并给出了此类非线性系 统的数值仿真结果.     

MR阻尼器的半主动控制研究

MR阻尼器能提供可以调节的阻尼力,适合用作减少结构地震响应的半主动控制器。本文对MR阻尼器的半主动控制进行研究,提出了状态跳跃算法,根据结构响应的大小实现MR阻尼器的状态切换,使结构响应得到有效的控制。这种控制策略简便,不需要在线计算,便于实施。由于速度响应直接影响MR阻尼器的阻尼力,建议用速度响应作为MR阻尼器进行状态切换的变量。文中给出了两个算例,进行了计算分析和比较,说明了状态跳跃控制算法的特点。     

斜拉索振动控制中MR阻尼器选型的研究

以全索全时段振动响应的均方根(RMS)评价MR阻尼器对斜拉索的减振效果。计算结果表明MR阻尼器型号是影响斜拉索减振效果的最主要因素。斜拉索的减振效果在选用合适的MR阻尼器时达到最佳。进而研究了MR阻尼器型号与阻尼器安装位置、施加的电压、斜拉索基频(张力、索长、质量)、激励荷载(类型、频率、幅值)等各种因素的关系,为MR阻尼器合理选型提供了优化设计的方法。型号选用主要是与斜拉索基频和MR阻尼器安装位置有关。在引起索基频变化的因素中,索质量对型号的选取影响最大;而索长对型号影响不大。对于索质量较大、张力较大、MR阻尼器安装位置较低、外界激励较大、频谱特征多变、低频为主时需要较强的MR阻尼器。进一步研究表明,半主动控制与开环控制的最优MR阻尼器型号有较好的一致性,因此半主动控制所选用的MR阻尼器型号可参照被动控制时最优MR阻尼器型号。     

Comparative research on semi-active control strategies for magneto-rheological suspension

This paper presents the comparison results of a study to identify an appropriate semi-active control algorithm for a MR suspension system from a variety of semi-active control algorithms for use with MR dampers. Five representative control algorithms are considered including the skyhook controller, the hybrid controller, the LQG controller, the sliding mode controller and the fuzzy logic controller. To compare the control performances of the five control algorithms, a quarter car model with a MR damper is adopted as the baseline model for our analysis. After deriving the governing motion equations of the proposed dynamic model, five controllers are developed. Then each control policy is applied to the baseline model equipped with a MR damper. The performances of each control algorithm under various road conditions are compared along with the equivalent passive model in both time and frequency domains through the numerical simulation. Subsequently, a road test is performed to validate the actual control performance. The results show that the performance of a MR suspension system is highly dependent on the choice of algorithm employed, and the sliding mode control strategy exhibits an excellent integrated performance.     

Stochastic minimax semi-active control for MDOF nonlinear uncertain systems under combined harmonic and wide-band noise excitations using MR dampers

A stochastic minimax semi-active control strategy for multi-degrees-of-freedom (MDOF) strongly nonlinear systems under combined harmonic and wide-band noise excitations is proposed. First, a stochastic averaging procedure is introduced for controlled uncertain strongly nonlinear systems using generalized harmonic functions and the control forces produced by Magneto-rheological (MR) dampers are split into the passive part and the active part. Then, a worst-case optimal control strategy is derived by solving a stochastic differential game problem. The worst-case disturbances and the optimal semi-active controls are obtained by solving the Hamilton–Jacobi–Isaacs (HJI) equations with the constraints of disturbance bounds and MR damper dynamics. Finally, the responses of optimally controlled MDOF nonlinear systems are predicted by solving the Fokker–Planck–Kolmogorov (FPK) equation associated with the fully averaged Itô equations. Two examples are worked out in detail to illustrate the proposed control strategy. The effectiveness of the proposed control strategy is verified by using the results from Monte Carlo simulation.     

Fast dynamic modeling for off-road track vehicles

The paper presents a simple, fast, and reliable dynamic model for an off-road track vehicle operating on terrain with obstacles. The method has been proven previously for wheeled-vehicle formulation. The model is based on a discrete body dynamics (DBD) method, which leads to simplistic linear decoupled motion equations. In this method, joints and bodies with relatively small mass are replaced with stiff springs and dampers, eliminating the system’s constraints and reducing the number of system bodies; this is important for accelerating the simulation runtime of the track vehicle model. The track in this approach is based on modeling each link as a point-mass. Two consecutive links are connected by stiff springs and dampers. This approach reduces the calculation time and increases system stability. The track–soil interaction was modeled using Bekker’s and Janosi’s formulation (Bekker, 1956; Hanamoto and Janosi, 1961). Specific soil properties were obtained for each link–soil interaction from soil classification and GIS. The link–ground contact was determined from topographic surface and adjustment of the force and direction acting on the track. The results of the simulation using the DBD method were compared with Siemens' VL commercial multibody dynamics program and with experiments reported in the literature. Results using the proposed method were found to be similar to the commercial program based on published experiments. The solution runtimes obtained for unpaved soil were two orders faster with the DBD method compared with the Siemens' VL program. The model was written as an independent software infrastructure, enabling easy integration with any other software component, such as a control system. The algorithm is in a suitable form for parallel processing calculation to speed up the runtime simulation close to real-time.     

Safety and comfort analysis of a 3-D vehicle model with optimal non-linear active seat suspension

A generalized nonlinear model is formulated for the dynamic analysis of suspension seats with passive, semi-active and active dampers. The model incorporates coulomb friction due to suspension linkages and bushings, forces arising from interactions with the elastic limit stops, a linear suspension spring and nonlinear damping force for passive, semi-active and active dampers, while the contribution due to biodynamics of the human operator is considered to be negligible. The semi-active and active dampers are characterized by force generators in accordance with the control laws based upon suspension mass velocity. Two different suspension seats are experimentally assessed in the laboratory under sinusoidal and random excitations arising from an urban bus, and the measured data is used to demonstrate the validity of the proposed generalized model. The results showed reasonably good agreement between the model results and the measured data. Optimal model parameters are selected using the sequential unconstrained minimization technique with an objective to minimize the acceleration due to vibration transmitted to the occupant mass. The comfort and safety performance characteristics of the optimal suspension seat with semi-active and active dampers are evaluated under both the sinusoidal and random excitations based on the guidelines provided by ISO-2631. From these results, it is concluded that the comfort performance of a suspension seat with semi-active and active dampers can be considerably enhanced by 20–30%.     

MR减振驱动器用于结构振动控制的算法研究

提出了四种半主动控制算法 ;针对安装有MR减振驱动器的三层剪切型结构仿真分析了各种半主动控制算法和被动控制策略的控制效果。仿真分析结果表明 ,MR减振驱动器作为一种半主动控制装置可以有效地控制结构的反应 ;施加最大磁场作为被动控制装置时 ,也对结构反应有很好的控制效果     

Restoring force and dynamic loadings identification for a nonlinear chain-like structure with partially unknown excitations

Most of the currently employed vibration-based identification approaches for structural damage detection are based on eigenvalues and/or eigenvectors extracted from dynamic response measurements, and strictly speaking, are only suitable for linear system. However, the inception and growth of damage in engineering structures under severe dynamic loadings are typical nonlinear procedures. Consequently, it is crucial to develop general structural restoring force and excitation identification approaches for nonlinear dynamic systems because the restoring force rather than equivalent stiffness can act as a direct indicator of the extent of the nonlinearity and be used to quantitatively evaluate the absorbed energy during vibration, and the dynamic loading is an important factor for structural remaining life forecast. In this study, based on the instantaneous state vectors and partially unknown excitation, a power series polynomial model (PSPM) was utilized to model the nonlinear restoring force (NRF) of a chain-like nonlinear multi-degree-of-freedom (MDOF) structure. To improve the efficiency and accuracy of the proposed approach, an iterative approach, namely weighted adaptive iterative least-squares estimation with incomplete measured excitations (WAILSE-IME), where a weight coefficient and a learning coefficient were involved, was proposed to identify the restoring force of the structure as well as the unknown dynamic loadings simultaneously. The response measurements of the structure, i.e., the acceleration, velocity, and displacement, and partially known excitations were utilized for identification. The feasibility and robustness of the proposed approach was verified by numerical simulation with a 4 degree-of-freedom (DOF) numerical model incorporating a nonlinear structural member, and by experimental measurements with a four-story frame model equipped with two magneto-rheological (MR) dampers mimicking nonlinear behavior. The results show the proposed approach by combining the PSPM and WAILSE-IME algorithm is capable of effectively representing and identifying the NRF of the chain-like MDOF nonlinear system with partially unknown external excitations, and provide a potential way for damage prognosis and condition evaluation of engineering structures under dynamic loadings which should be regarded as a nonlinear system.     

The effect of underplatform dampers on the forced response of bladed disks by a coupled static/dynamic harmonic balance method

Friction contacts are often used in turbomachinery design as passive damping systems. In particular, underplatform dampers are mechanical devices used to decrease the vibration amplitudes of bladed disks.Numerical codes are used to optimize during designing the underplatform damper effectiveness in order to limit the resonant stress level of the blades. In such codes, the contact model plays the most relevant role in calculation of the dissipated energy at friction interfaces. One of the most important contact parameters to consider in order to calculate the forced response of blades assembly is the static normal load acting at the contact, since its value strongly affects the area of the hysteresis loop of the tangential force, and therefore the amount of dissipation.A common procedure to estimate the static normal loads acting on underplatform dampers consists in decoupling the static and the dynamic balance of the damper. A preliminary static analysis of the contact is performed in order to get the static contact/gap status to use in the calculation, assuming that it does not change when vibration occurs.In this paper, a novel approach is proposed. The static and the dynamic displacements of the system (bladed disk+underplatform dampers) are coupled together during the forced response calculation. Static loads acting at the contacts follow from static displacements and no preliminary static analysis of the system is necessary.The proposed method is applied to a numerical test case representing a simplified bladed disk with underplatform dampers. Results are compared with those obtained with the classical approach.     

质量阻尼器的发展

广泛评述了调谐质量阻尼器(TMD)、多重调谐质量阻尼器(MTMD)、主动质量阻尼器(AMD)、半主动 TMD(SATMD)、主动调谐/主被动调谐/混合质量阻尼器(ATMD/APTMD/HMD)的研究现状.TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD能够有效地减小结构的风振与地震反应.指出强震下结构设置TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD的主要目的是限制结构屈服的进一步发展.因此,基于非线性结构模型的TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD研究具有重要意义.指出了TMD, MTMD, AMD, SATMD, ATMD/APTMD/HMD 有待于进一步研究的若干问题.提出了结构主动多重调谐质量阻尼器(AMTMD)和多重主被动调谐质量阻尼器(MAPTMD)的新控制策略.介绍了AMTMD和MAPTMD的研究进展并指出了进一步研究的发展方向.      

MR阻尼器的状态跳跃控制参数

对MR阻尼器实施状态跳跃控制可以有效地减少结构的地震响应，状态跳跃控制参数对半主动控制效果有很大的影响。本文对状态跳跃控制的相关参数进行了研究。利用两个数值算例，对采用不同类型的控制参数(位移、速度、加速度)、控制参数的大小、输入地震动的大小等相关因素对结构地震响应的控制效果进行了对比，发现采用速度响应作为状态跳跃控制变量对于减少绝对加速度响应是有利的；建议采用试算法确定合适的速度控制参数，通过和LQG控制相联系的方法给出了该控制参数最优值的估算方法。     

Efficient dynamic modelling and characterization of a magnetorheological damper

The present work is about the dynamic modelling and the experimental testing of magnetorheological (MR) dampers, especially at low frequency. The main improvement of this work over former models is the identification of dynamic parameters which are independent of the working conditions and vary only as a function of the current. A simple model is built on the basis of the literature and of a systematic experimental campaign, with the aim of simplifying the effort in retrieving the parameters and in controlling the system. The excitation current is introduced in the model as a variable, not only reducing the amount of test needed to assess the parameters, but also obtaining a faster model useful in motion control. A second order polynomial relationship between the applied current and the three variable parameters is found, showing a saturation effect at high currents. A verification test shows the reliability and the performance of the proposed model.     

Sweep technique to measure the relative performance of dampers

The sweep technique described in this paper represents a new method for measuring the relative performance of different dampers. Based on laboratory measurements, the technique is easy to use and keeps test execution time to a minimum. It also allows measurement of the relative performance of nonlinear dampers for which it is difficult to derive the analytical expression for their mechanical impedance. In addition to describing the test setup, the paper also presents results obtained from the application of this technique to four types of commercial dampers.     

基于磁流变阻尼器的多单体组合隔震结构模糊控制研究

提出了一种新的组合结构振动控制体系——多单体组合隔震结构,建立了力学模型及运动方程。基于瞬时最优控制算法,将控制力表达成阻尼力的形式,用磁流变阻尼器充当控制器,运用模糊控制方法对其进行控制。通过计算机仿真分析,并运用LQR控制与之进行对比。研究结果表明,这种组合隔震结构体系的控制效果明显,各结构的地震响应都有明显降低。采用模糊控制不需要建立精确的计算模型,并能达到与LQR控制相接近的控制效果。用磁流变阻尼器充当控制器减少了能量输入,在结构2与结构3之间安装弹簧-阻尼器使控制更容易实现。     

Longshore boundary conditions for numerical wave models

The problem of truncating nearshore finite element wave models is addressed. Incorrect treatment of the artificial boundaries of the model will cause spurious wave reflections. Three methods for dealing with these boundaries: application of constraints, use of the Smith condition and longshore dampers, are proposed. Numerical results show the dampers to be the best method.     

Three-dimensional dynamic model for off-road vehicles using discrete body dynamics

This paper presents a simple, reliable dynamics model of off-road vehicle operation in real-time (RT) on terrain with obstacles. The numerical model was formulated by a new method – DBD (Discrete Body Dynamics). The new method is based on a discrete-element method, where the equations of motion are linear and simple to solve.In this new method, the suspension systems are composed of soft and stiff springs and dampers (instead of suspension arms and joints constrains), to present the kinematics and dynamics of real suspension. Reduction of the number of bodies and avoidance of constraints significantly improves model efficiency and simplicity.The tires–soil interaction was modeled using Brixius prediction. Specific soil properties were obtained from the classification system for each tire–soil interaction, size, and geometric area. The tire–ground contact was determined by topographic surface and adjustment of the forces and direction acting on the tires.The proposed method allows quick and simple definition of a vehicle. The model is written as an independent software infrastructure, enabling easy integration with any other software component.Simulation results were compared with Siemens' VL commercial multibody dynamics program. The performance of the proposed method was very similar to the commercial program (R² > 0.9), with the significant advantage of much higher RT performance.