Simulation on motion of particles in vortex merging process

In a two-phase flow, the vortex merging influences both the flow evolution and the particle motion. With the blobs-splitting-and-merging scheme, the vortex merging is calculated by a corrected core spreading vortex method （CCSVM）. The particle motion in the vortex merging process is calculated according to the particle kinetic model. The results indicate that the particle traces are spiral lines with the same rotation direction as the spinning vortex. The center of the particle group is in agreement with that of the merged vortex. The merging time is determined by the circulation and the initial ratio of the vortex radius and the vortex center distance. Under a certain initial condition, a stretched particle trail is generated, which is determined by the viscosity, the relative position between the particles and the vortex, and the asymmetrical circulation of the two merging vortices.     

次谐波对混合层中拟序涡合并过程影响的数值研究

本文用拟谱方法对混合层二涡、三涡的合并规律进行了数值研究,分析了基波和交谐波之间相位差对涡合并过程的影响,并对此进行了解释。计算结果表明：二涡合并有配地和撕裂两种形式,且涡的完全通过撕裂合并的现象仅在相位差为π/2时出现;三涡合并有三种形式。通过计算可见,通过施加多级次谐波并改变它们之间的相位差可以主动控制拟序涡的发展和演变。     

An experimental study of the large scale coherent structures in a forced free shear layer

The dynamic characteristics of the large scale coherent structures in a forced free shear layer are experimentally studied by means of flow visualization. The quantitative measurements are acquired by the use of a LDV. It is shown that the development of the coherent structures can be greatly influenced by upstream artificial perturbations and as a result the mixing in the layer can be controlled. Like vortex merging, vortex splitting is also a common evolution pattern in the development of the coherent structures.     

Application of the VORTFIND algorithm for the identification of vortical flow features around complex three‐dimensional geometries

Accurate prediction of the hydrodynamic forces and moments acting on a manoeuvring marine vehicle using Reynolds averaged Navier–Stokes simulations requires sufficient mesh resolution to capture off‐body vortical structures. Because the path of these structures is not known a priori, a vortex identification and capture strategy is required alongside an iterative mesh adaption process. An improved version of the VORTFIND algorithm, which can identify multiple vortices of variable strength and rotational direction using a K‐means algorithm is described. The algorithm is applied to velocity fields generated from Reynolds averaged Navier–Stokes simulations to increase the mesh resolution in the vortex core region, ensuring sufficient mesh density to capture the downstream propagation of the vortex for a submarine hull at drift and ship propeller–rudder interaction.Copyright © 2012 John Wiley & Sons, Ltd.     

Asymmetric vortex merger: mechanism and criterion

The merging of two unequal co-rotating vortices in a viscous fluid is investigated. Two-dimensional numerical simulations of initially equal sized Lamb-Oseen vortices with differing relative strengths are performed. Results show how the disparity in deformation rates between the vortices alters the interaction. Key physical mechanisms associated with vortex merging are identified. A merging criterion is formulated in terms of the relative timing of core detrainment and destruction. A critical strain parameter is defined to characterize the establishment of core detrainment. This parameter is shown to be directly related to the critical aspect ratio in the case of symmetric merger.     

旋涡、湍流与自由表面的相互作用

旋涡及自由表面湍流与自由表面的非定常、非线性相互作用是当前流体力学中一个十分活跃的前沿领域的研究课题,它具有深刻的理论意义和重要的实用背景．旋涡、湍流与自由表面的相互作用是一个非常复杂的非线性、非定常过程,涉及到涡－涡、波－涡相互作用,旋涡在自由表面处的断裂、重联、合并及自由表面湍流中的准拟序结构的形成、发展等复杂动力学过程．关于这一领域的研究已经取得了一些重要成果．对旋涡与自由表面的相互作用的基本过程有了较为清楚的认识;但对湍流与自由表面的相互作用中的许多基本物理过程还知之甚少．本文综述此领域的实验、理论和数值模拟研究的最新进展和主要结果,讨论若干有待解决的问题,并指出进一步的研究方向      

The merging of two co-rotating vortices: a numerical study

The merging of two-dimensional co-rotating vortices is analysed through direct numerical simulations at large Reynolds numbers. It is shown how the Reynolds number affects each of the three phases that characterise this phenomenon. In the first phase, we examine the merging onset and focus on its definition. During the second rapid phase, the contributions of various flow regions upon the dynamics of a vortex are quantitatively studied. These regions are respectively the companion vortex, the filaments and an intermediate zone between vortices and filaments. The third phase is interpreted in terms of an advection diffusion process. Finally the final profile and circulation of the merged vortex is determined: the two thirds of the total circulation of the two initial vortices is contained in the newly formed vortex.     

Thin‐tube vortex simulations for sinusoidal instability in a counter‐rotating vortex pair

A thin‐tube vortex method is developed to investigate the intrinsic instability within a counter‐rotating vortex pair system and the effects from the core size and the wavenumbers (or wavelengths). The numerical accuracy and the advantages of the scheme are theoretically estimated. A nearest‐neighbour‐image method is employed in this three‐dimensional vortex simulation. Agreement with Crow's instability analysis has been achieved numerically for the long‐wave cases. A short‐wave instability for the zeroth radial mode of bending instability has also been found using the thin‐tube vortex simulations. Then, the combinations of long‐ and short‐wave instability are investigated to elucidate the non‐linear effects due to the interactions of two different modes. It is shown that instability is enhanced if both long‐ and short‐wave instabilities occur simultaneously. Although the method used in the paper is not capable of including effects such as axial flow, vortex core deformation and other complicated viscous effects, it effectively predicts and clarifies the first‐order factor that dominates the sinusoidal instability behaviour in a vortex pair. Copyright © 2002 John Wiley & Sons, Ltd.     

Reconnections of vortex filaments

The process of break-down and reconnection of vortex filaments is considered by the method of three-dimensional vortex singularities (vortons) in various situations, including oblique interaction of a vortex ring with a boundary in shear flow, shedding of a vortex ring from a horseshoe vortex, instability of elliptic vortex ring, Crow instability of two perturbed antiparallel vortex filaments, merging and subsequent splitting of vortex rings. Special attention is paid to the global integrals (vorticity, momentum, angular momentum) and to the inviscid dissipation of energy. The visualization of the effective vortex core, created by the interference of the vorticity fields of vortons, is presented. The comparisons with other methods of simulation of three-dimensional vortex interactions and with the observations have been made.     

Coaxial interactions of two vortex rings or of a ring with a body

Inviscid coaxial interactions of two vortex rings, including head-on collisions and leapfrogging motions, are considered using a contour dynamics technique. Interactions of vortex rings with solid bodies are also investigated by combining the contour dynamics technique with a boundary integral equation method. Numerical results show that a clean, successful passage motion is possible for two vortex rings with not too thick cores. In both cases of head-on collisions and leapfrogging motions, very large core deformations are observed when two vortex rings get close to each other. A head-tail structure is formed in the later stage of a head-on collision of two fat vortices. Numerical results also show that a vortex ring will stretch and slow down when it moves toward a solid boundary, will shrink and speed up when it moves away from a solid boundary, and will either translate steadily or approach an oscillating asymptotic state when it is far away from any boundaries. The project supported by The National Education Commission of China and NASA under cooperative grant agreement #NCC5-34.     

Patched grid and adaptive mesh refinement strategies for the calculation of the transport of vortices

This paper presents two techniques allowing local grid refinement to calculate the transport of vortices. one is the patched grid (PG) method which allows non‐coincident interfaces between blocks. Treatment of the non‐coincident interfaces is given in detail. The second one is the adaptive mesh refinement (AMR) method which has been developed in order to create embedded sub‐grids. The efficiency of these two methods is demonstrated by some validating tests. Then the PG and AMR strategies are applied in the computation of the transport of vortices. We start with a simple vortex flow in a cubic box. Then, the flowfield around a complex aircraft configuration is calculated using the two refinement techniques. Results are compared with a fine, referenced grid calculation. Copyright © 2002 John Wiley & Sons, Ltd.     

Reynolds number dependence of two-dimensional laminar co-rotating vortex merging

The paper reports unsteady Navier–Stokes calculations of laminar two-dimensional co-rotating vortex merging for various Reynolds numbers. The unsteady, incompressible two-dimensional Navier–Stokes equations were solved with fourth-order Runge–Kutta temporal discretization and fourth-order symmetric compact schemes for spatial discretization. Calculations of the unsteady Taylor vortex benchmark showed that fourth-order accurate solutions for all primitive variables were indeed achieved. Calculations for a pair of equal-strength co-rotating vortices show good agreement with reported direct numerical simulation and experiments for the evolution of the separation distance and core radius. It is found that the time required for merging is inversely proportional to the square root of the Reynolds number. According to previous experimental research, it was also found that complete merging in laminar regime undergoes four stages with physical meaning. The physical mechanism responsible for the merging process is investigated and it is found that the antisymmetric vorticity dynamics plays an important role until full merging.     

逆向涡对超疏水壁面减阻影响的TRPIV实验研究

超疏水壁面由于具有减阻和自清洁功能而成为国内外减阻和海洋防污等研究领域的热点之一,而20世纪湍流中相干结构的发现为湍流的控制指出新的方向,尤其近壁区涡结构对摩擦阻力贡献很大.利用高时间分辨率粒子图像测速技术,研究了超疏水壁面(SH)以及亲水壁面(PH)湍流边界层中正负展向涡的空间分布特征,研究逆向涡对超疏水壁面近壁区流动结构的影响和超疏水壁面的减阻机理.首先利用空间多尺度局部平均涡量的概念提取壁湍流发卡涡展向涡头(顺向涡)和逆向涡,实现了准确识别涡心并排除小尺度涡的干扰;然后根据检测到的顺向涡和逆向涡流线分布图,发现逆向涡始终处于正向涡的上游和下方,并且对正向涡的进一步发展起抑制作用;最后对两种壁面边界层中逆向涡数量以及出现概率进行对比,发现具有减阻效果的超疏水壁面边界层中出现更多逆向涡.说明逆向涡可抑制上方顺向涡与壁面的强烈剪切,并使靠近壁面的流体加速,从而产生减阻效果;超疏水壁面中涡结构具有更大的β角,使其更好地阻碍了发卡涡头附近强烈的喷射和扫略;超疏水壁面逆向涡出现概率明显大于亲水壁面.这些结果表明:超疏水壁面表现出的减阻特性(Reδ≈13 500,减阻5.8%)与两板产生逆向涡的差异有关.     

圆射流中拟序涡配对的数值模拟

用三维涡丝法结合涡丝的增加与合并技术,对不可压圆射流场,数值模拟了在扰动中加入次谐波后流场拟序涡的配对,配对情况与实验结果一致,通过对不同时刻涡量图的比较与分析,给出了次谐波初始强度对涡配对的影响,初始强度越大,涡配对出现越早,涡配对位置越往上游移动;同时还得到了基波与次谐波初始相位差和涡配对的关系,没有相位差时,次谐波增长最快,相位差增加时,涡配对的速度降低。说明控制次谐波的初始强度和基波与次谐波的相位差,能起到控制圆射流剪切层乃至控制整个射流场的目的。     

Splitting,merging and spanwise wavenumber selection of Dean vortex pairs

Splitting, merging and spanwise wavenumber selection are studied during the initial development of Dean vortex pairs in a channel with mild curvature, an aspect ratio of 40, and an inner to outer radius ratio of 0.979. Two types of splitting events, and four types of merging events are evident from flow visualizations at Dean numbers from 75 to 220. These events are described in detail along with observations that occurrances of these different events are tied to spatial and temporal variations of spanwise wavenumbers of vortex pair spacing. Also discussed are frequency spectra of different events, recurrent phenomena, and the part played by splitting and merging in laminar to turbulent transition in curved channels.This study was sponsored by the Propulsion Directorate, U.S. Army Aviation Research and Technology Activity-AVSCOM, NASA-Defense Purchase Request 030030-P. Professor C. S. Subramanian provided assistance in setting up the traversing system and data acquisition systems used for this study. Mr. R. E. Hughes assisted in obtaining some of the results presented.     

三角翼前缘涡的某些破裂形式及特性研究

基于流动显示和PIV技术测量的实验结果，对三角翼前缘涡破裂的一些形式和破裂特性进行了分析和讨论。通过PIV测量所得到的涡量分布证实了在螺旋破裂的情况下，涡核的螺旋方向与前缘涡的旋转方向相反，及双螺旋破裂形式的存在等。进而对螺旋波的形成机理提出了与有关文献不同的看法。     

基于涡旋识别方法的高速列车尾涡结构的讨论

利用改进型延迟分离涡模拟方法对缩尺比例1:30的高速列车简化模型的绕流流场进行数值计算,主要针对近尾流区的涡旋结构展开具体讨论. 通过不同的涡旋识别方法,发现在尾涡结构中,高涡量的强涡旋主要聚集于尾车附近,而涡量较低但处于相对稳定状态的涡旋分布在大部分尾流空间中. 对此,主要基于最新提出的涡旋定义及其物理意义认为,由于边界层在尾部发生的流动分离,剪切变形以及高涡量的扩散对强涡旋的形成发挥着重要的作用,而涡旋会被较强的剪切旋转拉伸,使得局部复杂的流动表现出突出的湍流特性;另一方面,尽管涡强度明显下降,但是在强剪切应变迅速衰减的情况下,流向涡核中的涡旋涡量是主要的,此时,在较接近地面的情况下,流体微团以涡核为中心的旋转运动使得涡旋与地面之间的相互作用成为主导的流动机制. 虽然涡强度会相对缓慢地衰减,但是从湍流能量产生的角度,该机制对涡旋的自维持发挥重要的作用,从而使尾涡结构能够相对稳定地存在于尾流流动中.      

非对称槽道中涡旋波的特性研究

利用PIV流场显示技术，对振荡流体在非对称槽道中涡旋波的产生、发展和消失的规律进 行了实验研究和分析，测得了涡旋波流场的速度矢量图，阐明了涡旋波流场周期性变化的特 点. 结合涡动力学方程，深入分析并揭示了做周期性运动的流体能在槽道中产生波的特性这 一规律，从中发现：流体周期变化的非定常性和不对称的槽道结构是形成涡旋波流动的主要 因素. 本文对涡旋波流场中各个旋涡的速度分布和涡量进行了测量和计算，分析了涡旋波 强化传质的机理，并研究了Re数对涡旋波流动的影响     

带有涡襟翼的翼—身组合体分离涡特性的实验观察研究

本文采用水洞流谱观测方法,研究了带有涡襟翼的翼—身组合体前缘分离涡及涡系干扰的流动特性,并与普通翼—身组合体情况进行比较;分析了涡襟翼的涡流运动特点及其升阻比增大的机理;讨论了翼—身组合体涡系干扰的主要反映及对涡破碎特性的影响;并对非对称体涡出现的条件以及分离旋涡在稳定发展过程中的抗干扰能力提出了看法.     

A Lagrangian vortex method for unbounded flows

A technique is presented for velocity calculations on the highly distorted node distributions typical of those found in Lagrangian vortex methods. The method solves the partial differential equation for streamfunction directly on the nodes, via a sparse, symmetric system of equations that can be solved using standard iterative solvers. When implemented in a triangulated vortex method, the technique gives computation times which scale as N^1.23, where N is the number of nodes. The computation scheme is derived for two‐dimensional problems and applied to the prediction of the evolution of perturbed multipolar vortices. Due to the numerical performance of the method, it has been possible to examine such evolution at higher and lower Reynolds numbers than have been considered in published numerical studies. Copyright © 2008 John Wiley & Sons, Ltd.