氢氧燃烧及爆轰驱动激波管

分析并观察了沿驱动段轴向分布多火塞燃烧驱动段的性能．提出主膜处同一管截面均匀分布三火花塞引燃的点火方法．用这种点火方法驱动产生的入射激波强度重复性较高,激波后气流速度、温度和压力的定常性亦大大改善,可满足气动试验实际要求．提出在驱动段尾端串接卸爆段来消除爆轰波反射高压,从而可使反向爆轰驱动段用来产生高焓高密度试验气流．这种反向爆轰驱动产生的入射激波重复性高,激波衰减弱．在主膜处的收缩段产生的反射波可缓解爆轰波后跟随的稀疏波的不利影响,从而使前向爆轰驱动具有实用性．在产生的入射激波强度相同条件下,前向爆轰驱动所需的爆轰驱动段可爆混合气初始压力可较反向爆轰低近一个量级．     

一种新的运动激波--非定常边界层相互干扰现象

本文探讨了一种新的激波－非定常边界层相互干扰现象，这种激波－边界层干扰现象既不同于定常激波－边界层干扰现象，又不同于激波在端面反射后与该激波所诱导的边界层之间的干扰现象，而是运动激波与稀疏波和第一激波所诱导的非这常边界层之间的干扰现象，本文对这种现象用微波动力学理论进行分析，并把这种干扰现象看成激波的绕射现象，同时在稀疏波破膜的双驱动激波管中进行实验观察，最后把理论分析与实验观察进行了比较。     

活塞式无膜激波管特性的实验研究

本文在自行研制的无膜激波管中，实验研究了不同快速卸压装置对该激波管运行特性的影响。通过控制高压段充气压力和测量压力波形，得到了高低压段压比和激波马赫数的关系曲线以及在测压点处形成激波所需的最低压比。实验结果表明排气快慢对激波形成距离和所形成激波的强度产生很大的影响。对不同装置产生的结果差异进行了一定的分析。     

气相爆轰波冲击气固界面的透反射特性

为了研究气相爆轰波冲击气固界面过程中透射波和反射波的相关特性,建立爆轰波冲击气固界面的一维理论模型,对不同初始压力条件下爆轰波到达气固界面后的界面两侧的压力和界面速度变化进行分析。利用时空守恒元求解元方法对气相爆轰波冲击气固界面过程进行数值模拟,分析气体部分反射波的压力分布和速度变化规律及透射入固体中应力波的波形和波速特征,并搭建气相爆轰波冲击活塞实验装置进行进一步验证。结果表明:气体爆轰波到达气固界面后,在固体中透射指数形式的弹性波,并在界面处向气体区反射一道激波。爆轰波后的稀疏波与反射激波相交,削弱反射激波,最终形成稳定激波回传。气固界面在稀疏波和反射稀疏波的作用下,压力和速度逐渐下降,最终也形成稳定状态。在不同混气初始压力情况下,爆轰波冲击过程中产生的最高压力和爆压的比值基本保持不变。理论模型对特征点相关物理量的计算值和实验数据符合的较好。     

爆轰波与激波对撞的实验研究

对乙炔氧气混合气体中爆轰波与激波的正面对撞现象的实验研究是以高速摄影获取两波对撞的x-t纹影图,以烟迹板记录对撞中的爆轰胞格图案,并基于激波理论和经典CJ爆轰理论求解了两波对撞的稳态解并探寻其规律. 研究发现透射波系包括一道激波和爆轰波,以及紧随爆轰波后的稀疏波区,这一结果对应于一维理论分析中的CJ解. 透射波系基本不受初始压强影响;初始温度也只成比例地改变流场整体速度,温度越高,速度越快;对波系起实质影响作用的是入射激波强度,激波越强,则整个透射流场呈现偏向激波的趋势;理论分析还指出,稀疏波区的出现不可避免,当激波强度趋于声波稀疏波区趋于消失,激波越强则疏波区趋于扩大. 两波对撞存在一个有限的转变阶段,透射爆轰首先减缓,接着迅速迸发为过驱爆轰,然后再逐渐平衡为CJ爆轰. 对于强不稳定的燃气,对撞后爆轰波在空间上的发展极不均衡,一些区域发生火焰面与诱导激波的严重脱离,随后的火焰面失稳发展为诱导激波区内的爆轰波,实验观察到了这种爆轰在烟迹板上留下的极为精细的迹线.      

前向爆轰驱动变截面激波管特性的数值模拟

讨论的激波管由氢氧前向爆轰产生高压驱动气体、并配有收缩截面段,它能产生高焓超高速气流.对此进行了模拟.既对变截面角度的作用,两端截面积比的作用又对比正向反向爆轰有何不同效果做了探讨.正向爆轰时主膜处的收缩段产生的汇聚作用既加强主激波又产生反向激波,缓解了爆轰波阵面后紧跟着的稀疏波导致主激波衰减偏快的不利影响.当收缩角度在30°和45°之间时,主激波的强度较高,衰减较小;当β接近90°时在主激波传播过一小段距离之后,主激波后高温高速气流较均匀,且主激波的衰减最小,具有实用价值.驱动段与被驱动段的截面积比越大,主激波的强度越高,但是最初阶段衰减也越快.反向爆轰时产生的主激波衰减最缓,但是同样的主激波强度需要的驱动段与被驱动段初始压力比前向爆轰高1个量级.     

系列生物激波管的研制与应用

本文介绍了国内唯一的大、中、小系列生物激波管的研制和应用。大型总长39.0m,试验段内径1m,驱动段最大超压可达10.3MPa,利用其末端挡板反射稀疏波的运行而可产生负压。中型总长34.5m,驱动段最大超压为22MPa,试验段为组合式,内径77～60mm,可作超压、爆炸性减压和水下爆炸波等试验。小型总长0.5m,设计承压为68.6MPa。三种激波管均用双夹膜将驱动段与试验段分开。动物实验表明,此套装置可使大、小动物产生不同程度的全身或局部冲击伤,可满足冲击伤实验研究的需要。     

基于立方型气体状态方程的激波风洞准一维流动数值研究

采用基于立方型气体状态方程的准一维流动数值模拟方法研究了反射式高焓激波风洞的真实气体流动,重点关注了高压真实气体效应对风洞全场流动时空结构和驻室区气流参数的影响,并以理论分析揭示了高压真实气体效应对激波管内流动的作用机理。研究表明：对于以冷高压气体驱动的激波风洞,使用考虑分子体积和分子间作用力的真实气体状态方程能够更准确地描述气体的状态和风洞内的流动状况。高压真实气体效应主要在冷驱动气体中发生作用,其作用效果主要是使当地声速增大,从而使得入射稀疏波和反射稀疏波的传播速度加快;另一方面,高压气体效应在高温气体效应较显著的被驱动气体中作用微弱,且对激波管产生激波的强度和激波后的流动状态影响甚微。稀疏波的加快传播改变了激波管波系的相干时空关系。提前抵达的稀疏波可在一定情况下侵蚀激波风洞的有效试验时间。对于所测试的激波风洞构型,在150 MPa氢气驱动110 k Pa氮气的工况下,高压效应导致的有效试验时间缩短约38%。适当加长驱动段长度和采用高温气体驱动均可有效减弱高压真实气体效应的影响。     

气相爆轰波正反射激波加速研究

实验采用压力传感器测量了指定点压力时间曲线。数值模拟基于二维反应欧拉方程和基元反应模型,采用二阶附加半隐的龙格-库塔法和5阶WENO格式分别离散时间和空间导数项,获得了指定点数值压力时间曲线。理论分析基于爆轰理论和激波动力学,分析了气相爆轰波反射过程所涉及的复杂波系演变并获得了反射激波速度。结果表明:本文数值模拟和理论计算定性上重复并解释了实验现象。气相爆轰波在右壁面反射后,右行稀疏波加速反射激波。其加速原因是:尽管激波波前声速减小,但激波马赫数增大,波前气流速度减小。在低初压下,可能还由于爆轰波后未反应或部分反应气体的作用,导致反射激波加速幅度比高初压下大。     

激波与涡对相互作用的实验研究

在方截面激波管中进行了平面运动激波和涡对的二维相互作用实验，研究了激波与同向涡对、激波与反向涡对相互作用的非定常过程．根据实验照片，分析讨论了作用过程中激波的变形，二次激波和三波点的形成、演变，激波与激波的相互作用，以及旋涡结构的变化等．实验表明，激波通过涡核时，激波发生剧烈变形，旋涡强度增大，涡核形状改变．     

Oxyhydrogen combustion and detonation driven shock tube

The performance of combustion driver ignited by multi-spark plugs distributed along axial direction has been analysed and tested. An improved ignition method with three circumferential equidistributed ignitors at main diaphragm has been presented, by which the produced incident shock waves have higher repeatability, and better steadiness in the pressure, temperature and velocity fields of flow behind the incidence shock, and thus meets the requirements of aerodynamic experiment. The attachment of a damping section at the end of the driver can eliminate the high reflection pressure produced by detonation wave, and the backward detonation driver can be employed to generate high enthalpy and high density test flow. The incident shock wave produced by this method is well repeated and with weak attenuation. The reflection wave caused by the contracted section at the main diaphragm will weaken the unfavorable effect of rarefaction wave behind the detonation wave, which indicates that the forward detonation driver can be applied in the practice. For incident shock wave of identical strength, the initial pressure of the forward detonation driver is about 1 order of magnitude lower than that of backward detonation. The project supported by State Science and Technology Committee, National Natural Foundation of Science of China (19082012), Chinese Academy of Sciences and Project of National High Technology of China. In memory of academician Kuo Yonghuai's 90th anniversary.     

The effects that changes in the diaphragm aperture have on the resulting shock tube flow

In a conventional shock tube, the driver and the driven sections have similar (if not identical) cross-sectional area and the diaphragm opened area, upon rupturing, is practically equal to the tube cross-sectional area. Such geometry results in generating a well-formed shock wave in the tube’s driven section. The present experimental work checks the effects that changes in the diaphragm ruptured area have on the generated shock and rarefaction waves. Experiments were conducted in an 80?mm by 80?mm cross section shock tube generating incident shock waves having Mach numbers within the range from 1.06 to 1.25. In each run, pressure histories were recorded along the driven and the driver sections of the shock tube. The recorded pressures reveal that progressive reduction in the diaphragm open space resulted in a weaker shock and both longer time and distance until the compression waves generated close to the diaphragm coalesces into a shock wave. In addition, reducing the open space of the diaphragm resulted in a significant slow down in the high pressure reduction prevailing in the driver section.     

平板撞击下C30混凝土中冲击波的传播特性

采用1级气炮加载技术和锰铜应力计多点测试技术,开展了C30混凝土在平板撞击条件下的冲击压缩实验研究。基于锰铜应力计实测的应力波形,研究了混凝土中冲击波的传播特性,结果显示冲击波的应力峰值随传播距离呈现明显的衰减特性,衰减过程可分为2个阶段。在早期阶段,卸载波没有赶上前面传播的冲击波,冲击波应力峰值衰减较慢,主要是混凝土材料的本构粘性效应所引起的;而后期阶段应力峰值的快速衰减则归因于混凝土材料的本构粘性效应、后续的来自飞片自由面的反射波追赶卸载、边侧稀疏波卸载及波传播的几何弥散效应的共同作用;另外,冲击波在混凝土中传播的升时也随着传播距离逐渐增大,即由强间断波逐渐转化为弱间断波。     

Formation of blast waves as a result of a low pressure domain decomposition

In this article the formation and propagation of blast wave as a result of a focusing of shock wave in a domain with low pressure and density are examined in the frame of an ideal gas model. We consider the decomposition of a pressure-density discontinuity on the boundary of the spherical (or cylindrical) domain which is filled by a gas whose pressure and density are lower than the pressure and density of gas that filling the external space. At initial moments of this decomposition the rarefaction wave propagates in the external space and the converging shock wave is formed in the domain of low pressure and density. The intensity of the converging shock wave gradually increases, and the wave transitions to the self-similar regime. After implosion, a diverging shock wave is formed which propagates through the disturbed gas. The values of wave intensity, wave impulse and other parameters for some magnitudes of initial parameters have been determined by means of numerical calculations. Received 10 August 1997 / Accepted 13 July 1998     

Specific gasdynamical features of spontaneous condensation in an unsteady rarefaction wave

On the basis of numerical modeling, the formation of an unsteady shock wave induced by a condensation shock in a rarefaction wave moving in the high-pressure channel of a shock tube filled with moist air is demonstrated. It is shown that in a fairly long channel a periodic structure consisting of an alternating sequence of condensation shocks and the shock waves they generate may be formed. This structure is a linear unsteady analog of the self-oscillation regime of type IV in the classification [1] for condensing medium flows in the subsonic section of a Laval nozzle. The specific features detected are important for planning and interpreting experiments aimed at investigating spontaneous condensation using a “condensation shock tube”.     

激波风洞高低压段钢膜片破裂特性研究

激波风洞是用于高超声速飞行器气动外形设计和优化的常用地面试验装置,基于爆轰驱动技术,激波风洞能够在短时间(毫秒级)内产生高温、高压的驱动气体来模拟高超声速试验气流.主膜片位于激波风洞中的爆轰驱动段和激波管段之间,试验时膜片在爆轰脉冲压力下打开,膜片的打开状态和脱落情况对激波风洞气流品质有很大的影响. 同时,膜片也是形成激波的先决条件. 传统的风洞采用铝质膜片进行试验,在激波风洞中需要承压能力更强的膜片, 此时铝质膜片不再适用, 需要采用钢质膜片.因此, 对激波风洞中的钢膜片破裂特性进行研究很有必要.将数值计算结果与试验结果进行比较, 发现数值计算结果与试验结果吻合得比较理想,计算结果具有可靠性. 基于膜片的应力-应变模型, 建立了膜片打开的动力学模型,根据CJ爆轰理论, 采用有限元软件计算模拟了膜片破裂的过程,分析总结了膜片破裂的机制和力学特性规律.采用控制变量法对不同厚度和凹槽长度的膜片进行分析研究,得到了膜片破膜压力和有效破膜时间的变化规律. 在激波风洞试验中,根据膜片总破膜时间设计了适用于JF-12复现风洞的膜片参数.      

SHOCK INITIATION OF EXPLOSIVES INVESTIGATED WITH SMALL PARTITION EXPERIMENT AND NUMERICAL SIMULATION

In order to investigate the shock ignition of high energy solid explosives by shock waves,we carry out Lagrangian experiments with 2-D Lagrangian technique which uses composite manganin-constantan(CMC).The efects of the shock sensitivity of pressed solid high explosives,TNT,and the efect of the lateral rarefaction wave were studied.Based on the measured pressure histories and the radial displacements,we formulate the Ignition and Growth reactive flow models for the pressed TNT.The shock initiation process simulated by Ignition and Growth model agreed well with experimental data.This pressed TNT model can be applied to shock initiation scenarios which are highly unpredictable and have not been or cannot be tested experimentally.     

探索发展激波风洞爆轰驱动技术

发现了燃烧驱动激波管中入射激波马赫数异常升高的起因. 实验显示爆轰驱动能力强于燃烧驱动, 从而推动爆轰驱动技术的发展. 采用卸爆管消除爆轰波反射高压以及双爆轰驱动段全部消除爆轰波后的Taylor稀疏波, 使反向和前向爆轰驱动模式具有实用价值. 反向爆轰驱动技术还成功用来延长激波风洞试验时间.