接触爆炸荷载对钢筋混凝土梁的局部毁伤效应

为得到接触爆炸下钢筋混凝土（reinforced concrete，RC）梁的局部破坏模式和毁伤效应，对同一尺寸的RC梁进行了不同装药量的接触爆炸试验研究。试验中采用框架结构中典型工程尺度RC原型梁为研究对象，通过4次爆炸试验，观测了RC梁在不同装药量下的局部破坏模式和破坏特征，分析了装药量对局部毁伤效应的影响。研究结果表明:接触爆炸荷载作用下，RC梁将发生正面成坑、侧面崩落、背面震塌和截面冲切等局部破坏模式，爆坑深度、震塌厚度、表面毁伤面积以及受压区纵筋变形均与装药量立方根近似呈线性增加关系。在试验数据基础上，将RC梁局部毁伤程度划分为轻度毁伤、中度毁伤、重度毁伤和严重毁伤4个等级，采用比例装药量判据进行评估。研究成果可为抗爆结构设计和结构毁伤评估提供理论依据。     

方形钢筋混凝土板的近场抗爆性能

为了探讨钢筋混凝土板在爆炸载荷作用下的抗爆性能,对方形钢筋混凝土板在单向支撑条件下进行了近场爆炸加载实验,实验中采取TNT装药对钢筋混凝土板进行加载.并利用AUTODYN软件采用流固耦合算法,建立了混凝土和钢筋三维分离式实体模型,对钢筋混凝土板的动态响应过程进行数值模拟,且考虑应变率对钢筋和混凝土材料的动态本构特性的影...     

非贯通裂隙岩体损伤演化率相关性及变形特征

含非贯通裂隙岩体是自然界中岩体的主要赋存形式，其裂隙几何特征对岩体的强度及变形均产生显著影响。应变率对岩体的损伤演化及黏滞效应也具有显著的率相关性。首先，运用模型元件的方法，将非贯通裂隙岩体动态破坏过程视为具复合损伤、静态弹性特性、动态黏滞特性的非均质点组成，对黏弹性响应的Maxwell体进行改进，将细观损伤体与裂隙损伤演化的宏观损伤体根据等效应变假设并联组成宏细观复合损伤体，构建综合考虑岩体宏细观缺陷的动态损伤模型；其次，基于断裂力学及应变能理论，对岩体宏观裂隙动态扩展的能量机制进行分析，综合考虑初始裂隙应变能、裂隙动态损伤演化过程应变能、裂隙闭合应变能，得到裂隙岩体宏观动态损伤变量计算公式；最后，将模型计算结果与实验结果进行比较，模型计算结果与实验结果吻合较好，证明了模型的合理性，同时利用模型讨论了裂隙倾角、应变率、岩石性质对岩体变形特征的影响规律。     

Nonlinear progressive damage model for composite laminates used for low-velocity impact

In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impact is presented. Being applied to three-dimensional （3D） solid elements and cohesive elements, the nonlinear damage model can be used to analyze the dynamic performance of composite structure and its failure be- havior. For the intralaminar damage, as a function of the energy release rate, the damage model in an exponential function can describe progressive development of the damage. For the interlaminar damage, the damage evolution is described by the framework of the continuum mechanics through cohesive elements. Coding the user subroutine VUMAT of the finite element software ABAQUS/Explicit, the model is applied to an example, i.e., carbon fiber reinforced epoxy composite laminates under low-velocity impact. It is shown that the prediction of damage and deformation agrees well with the experimental results.     

水下冲击波载荷作用下气背固支圆板动态毁伤实验

为了研究水下近爆载荷作用下舰艇水下结构的动态变形及失效毁伤模式,利用水下爆炸冲击波等效加载装置结合高速摄影技术,对两种厚度的气背固支5A06铝合金圆板进行了水下冲击波加载实验。得到了气背固支圆板塑性大变形、中心拉伸撕裂和边界剪切破坏3种典型失效模式的动态响应历程。比较分析了冲击波强度、冲击因子、损伤参数和响应参数4种毁伤判据对该类靶板毁伤模式的判别能力。实验结果表明:考虑了结构因素的损伤参数和响应参数能够更为全面的判别结构的失效毁伤情况。     

Hysteretic deteriorating model for quasi-brittle materials based on micromechanical damage approach

A damage model, which is based on the stochastic modeling of the microstructures, is developed for the quasi-brittle materials subjected to repeated loading. According to this model, the overall response of the material is represented with a series of micro-elements joined in parallel. A combined model is proposed for the micro-element considering the fracture as well as the hysteretic energy dissipation. To account for the progressive failure, the random fracture strains are assigned to the micro-elements. Therefore the overall parallel bundle is considered as a stationary random field. Then by averaging the microscopic random field, the overall loading, unloading and reloading curves are derived analytically. Two hysteretic rules are derived from the proposed model, and the overall hysteretic deteriorating behaviors could be well reproduced. To demonstrate the validity of the present model, the numerical results are shown against the stochastic simulated curves as well as the experimental data. The present model provides an alternative approach for the efficient modeling of the hysteretic deteriorating behaviors for the quasi-brittle materials.     

高应变率大变形下的聚丙烯/尼龙共混高聚物损伤型本构特性

对两种采用不同相容剂的聚丙烯（PP）和尼龙（PA）共混高聚物材料在大变形下的粘弹性力学行为进行研究,着重考察应变率效应和损伤的演化,从而分析不同的界面分子设计对共混体系材料宏观性能的作用。在准静态及冲击实验研究的基础上,基于ZWT非线性粘弹性模型,并结合了遗传算法,分别得到了能有效描述两种共混高聚物大变形阶段计及损伤的非线性粘弹性本构关系。两种材料在不同加载条件下表现出明显不一致的性能,原因在于其损伤演化的率相关性,且两种材料的大变形机制存在一定的差别,能用ZWT方程进行描述的范围也不一样。     

泡沫铝防护钢筋混凝土板的抗爆性能

为研究多孔吸能材料泡沫铝板对工程结构的抗爆防护作用，开展室外爆炸破坏实验，分别对设置不同泡沫铝防护层的钢筋混凝土（reinforced concrete，RC）板在爆炸荷载下的动态响应及破坏模式进行了研究，并运用LS-DYNA软件建立了有限元模型。通过与实验对照，验证了模型的可行性，对比分析了有、无泡沫铝防护层钢筋混凝土板的损伤破坏规律，并讨论了泡沫铝密度梯度分布和纵筋配筋率的影响。结果表明:有限元模型能够有效分析含泡沫铝防护层RC板的动态响应及其破坏形态；泡沫铝防护层能够有效减小钢筋混凝土板的挠度变形，降低试件的破坏程度；泡沫铝密度由下到上递增情况对RC板的减爆效果最好；增大配筋率可以提升泡沫铝防护RC板整体抗爆性能。     

Coupled thermo-hygro-mechanical damage model for concrete subjected to high temperatures

Based on the theory of mixtures, a coupled thermo-hygro-mechanical (THM) damage model for concrete subjected to high temperatures is presented in this paper. Concrete is considered as a mixture composed of solid skeletons, liquid water, water vapor, dry air, and dissolved air. The macroscopic balance equations of the model consist of the mass conservation equations of each component and the momentum and energy conservation equations of the whole medium mixture. The state equations and the constitutive model used in the model are given. Four final governing equations are given in terms of four primary variables, i.e., the displacement components of soil skeletons, the gas pressure, the capillary pressure, and the temperature. The processes involved in the coupled model include evaporation, dehydration, heat and mass transfer, etc. Through the process of deformation failure and the energy properties, the mechanics damage evolution equations are established based on the principle of conversation of energy and the Lemaitre equivalent strain assumption. Then, the influence of thermal damage on the mechanical property is considered.     

冲击荷载下钢筋混凝土梁的性能及损伤评估

基于落锤冲击试验，通过数值模拟研究钢筋混凝土梁在冲击荷载下的抗冲击性能和损伤机理。针对冲击荷载局部效应明显和持时短暂等特点，提出基于截面损伤因子的损伤评估方法；采用参数分析方法研究了箍筋间距、边界条件、冲头形状和面积以及冲击位置对钢筋混凝土梁的动态响应和损伤程度的影响。结果表明:基于截面的损伤评估方法能够比较直观地描述梁体损伤沿长度方向的分布；端部的固支约束可以有效地改变钢筋混凝土梁的耗能机制，并能提高梁的抗冲击承载潜力；冲击位置会直接影响梁体的裂缝分布和破坏模式；碰撞接触面积和冲头形状也对梁的损伤分布具有一定的影响。     

Unusual plastic deformation and damage features in titanium: Experimental tests and constitutive modeling

In this paper, we present an experimental study on plastic deformation and damage of polycrystalline pure HCP Ti, as well as modeling of the observed behavior. Mechanical characterization data were conducted, which indicate that the material is orthotropic and displays tension-compression asymmetry. The ex-situ and in-situ X-ray tomography measurements conducted reveal that damage distribution and evolution in this HCP Ti material is markedly different than in a typical FCC material such as copper. Stewart and Cazacu (2011) anisotropic elastic/plastic damage model is used to describe the behavior. All the parameters involved in this model have a clear physical significance, being related to plastic properties, and are determined from very few simple mechanical tests. It is shown that this model predicts correctly the anisotropy in plastic deformation, and its strong influence on damage distribution and damage accumulation. Specifically, for a smooth axisymmetric specimen subject to uniaxial tension, damage initiates at the center of the specimen, and is diffuse; the level of damage close to failure being very low. On the other hand, for a notched specimen subject to the same loading the model predicts that damage initiates at the outer surface of the specimen, and further grows from the outer surface to the center of the specimen, which corroborates with the in-situ tomography data.     

半结晶聚合物损伤演化的实验表征与数值模拟

损伤本构模型对研究材料的断裂失效行为有重要意义, 但聚合物材料损伤演化的定量表征实验研究相对匮乏. 通过4种高密度聚乙烯(high density polythylene, HDPE)缺口圆棒试样的单轴拉伸实验获得了各类试样的载荷-位移曲线和真应力-应变曲线, 采用实验和有限元模拟相结合的方法确定了HDPE材料不同应力状态下的本构关系, 并建立了缺口半径与应力三轴度之间的关系;采用两阶段实验法定量描述了4种HDPE试样单轴拉伸过程中的弹性模量变化, 并建立了基于弹性模量衰减的损伤演化方程, 结合中断实验和扫描电子显微镜分析了应力状态对HDPE材料微观结构演化的影响. 结果表明缺口半径越小, 应力三轴度越大, 损伤起始越早、演化越快; 微观表现为: 高应力三轴度促进孔洞的萌生和发展, 但抑制纤维状结构的产生;基于实验和有限元模拟获得的断裂应变、应力三轴度、损伤演化方程等信息提出了一种适用于聚合物的损伤模型参数确定方法, 最后将本文获得的本构关系和损伤模型用于HDPE平板的冲压成形模拟, 模拟结果与实验结果吻合良好.      

Analysis of creep deformation and creep damage in thin-walled branched shells from materials with different behavior in tension and compression

A constitutive model for describing the creep and creep damage in initially isotropic materials with different properties in tension and compression has been applied to the modeling of creep deformation and creep damage growth in thin-walled shells of revolution with the branched meridian. The approach of establishing the basic equations for axisymmetrically loaded branched shells under creep deformation and creep damage conditions has been introduced. To solve the initial/boundary-value problem, the fourth-order Runge–Kutta–Merson’s method of time integration with the combination of the numerically stable Godunov’s method of discrete orthogonalization is used. The solution of the boundary value problem for the branched shell at each time instant is reduced to integration of the series of systems of ordinary differential equations describing the deformation of each branch and the shell with basic meridian. Some numerical examples are considered, and the processes of creep deformation and creep damage growth in a shell with non-branched meridian as well as in a branched shell are analyzed. The influence of the tension–compression asymmetry on the stress–strain state and damage evolution in a shell with non-branched meridian as well as in a branched shell with time are discussed.     

多孔铁电陶瓷冲击压缩响应与损伤演化的离散元数值模拟

采用flat-joint粘结模型，建立多孔铁电陶瓷在一维应变冲击压缩下的PFC (particle flow code)颗粒流离散元模型，通过数值模拟再现了平板撞击实验中实测的自由面速度剖面历史，并揭示了多孔铁电陶瓷在冲击压缩下的响应过程与损伤演化机制。多孔铁电陶瓷在冲击压缩下的响应过程可分4个阶段:弹性变形、失效蔓延、冲击压溃变形、冲击Hugoniot平衡状态；其中，失效蔓延的内在机制是由剪切裂纹的成核与增长，而冲击压溃变形的主要机制是孔洞的塌缩以及层状剪切裂纹的形成与扩展；冲击速度与孔隙率对铁电陶瓷的响应有显著的影响，Hugoniot弹性极限强烈依赖于孔隙率，但与冲击速度的大小无关，宏观损伤累积随着冲击速度和孔隙率的增加而增加。     

Experiments and modeling of ballistic penetration using an energy failure criterion

One of the most intricate problems in terminal ballistics is the physics underlying penetration and perforation. Several penetration modes are well identified, such as petalling, plugging, spall failure and fragmentation (Sedgwick, 1968). In most cases, the final target failure will combine those modes. Some of the failure modes can be due to brittle material behavior, but penetration of ductile targets by blunt projectiles, involving plugging in particular, is caused by excessive localized plasticity, with emphasis on adiabatic shear banding (ASB).Among the theories regarding the onset of ASB, new evidence was recently brought by Rittel et al. (2006), according to whom shear bands initiate as a result of dynamic recrystallization (DRX), a local softening mechanism driven by the stored energy of cold work. As such, ASB formation results from microstructural transformations, rather than from thermal softening. In our previous work (Dolinski et al., 2010), a failure criterion based on plastic strain energy density was presented and applied to model four different classical examples of dynamic failure involving ASB formation. According to this criterion, a material point starts to fail when the total plastic strain energy density reaches a critical value. Thereafter, the strength of the element decreases gradually to zero to mimic the actual material mechanical behavior.The goal of this paper is to present a new combined experimental–numerical study of ballistic penetration and perforation, using the above-mentioned failure criterion. Careful experiments are carried out using a single combination of AISI 4340 FSP projectiles and 25[mm] thick RHA steel plates, while the impact velocity, and hence the imparted damage, are systematically varied. We show that our failure model, which includes only one adjustable parameter in this present work, can faithfully reproduce each of the experiments without any further adjustment.Moreover, it is shown that the most common failure criterion based on a critical strain is simply inadequate to reproduce the results, due to the linear nature of the damage evolution. The advantages of the energy-based failure criterion are discussed in detail.     

钢筋混凝土开孔深梁有限元分析与设计研究Finite element analysis of RC deep beams with openings and researching of the design method

钢筋混凝土深梁受力不同于浅梁,梁腹开孔后受力更趋复杂。现有的设计方法对深梁行为的解释不够完备,设计结果的适用性难以判断,设计规范也没有给出开孔深梁的设计条文。为研究深梁设计方法的有效性,本文采用了非线性有限元分析方法,引入适合混凝土结构非线性分析的断裂塑性模型,并考虑钢筋粘结滑移效应,对一系列开双孔或偏孔钢筋混凝土深梁试验进行仿真分析,所得结果与试验结果吻合良好,能够准确预测深梁在裂缝、破坏形态及承载力等方面的受力特征。研究表明现有的深梁设计方法中,压拉杆模型方法相较内力法和应力图形法更加经济有效。在仿真分析的基础上,提出了一种对开孔深梁具有普遍适用性的非线性设计方法,其设计结果具有高承载力、较好延性、经济的配筋量和充分的材料利用率的优点。     

复合材料层合板面内渐进损伤分析的CDM模型

基于连续介质损伤力学,提出了一个预测复合材料层合板面内渐进损伤分析的模型,它包括损伤表征、损伤判定和损伤演化3 部分. 模型能够区分纤维拉伸断裂、纤维压缩断裂、纤维间拉伸损伤和纤维间压缩损伤4 种损伤模式,定义了与4 个损伤模式对应的损伤状态变量,导出了材料主轴系下损伤前后材料本构之间的关系. 损伤起始采用Puck 准则判定,损伤演化由特征长度内应变能释放密度控制. 假定材料服从线性应变软化行为,建立了损伤状态变量关于断裂面上等效应变的渐进损伤演化法则. 模型涵盖了复合材料面内损伤起始、演化直至最终失效的全过程. 完成了含孔[45/0/-45/90]_2S 层合板在拉伸和压缩载荷下失效分析,结果表明该模型能合理进行层合板的强度预测和损伤失效分析.      

复合材料层合板面内渐进损伤分析的CDM模型简

基于连续介质损伤力学,提出了一个预测复合材料层合板面内渐进损伤分析的模型,它包括损伤表征、损伤判定和损伤演化3 部分. 模型能够区分纤维拉伸断裂、纤维压缩断裂、纤维间拉伸损伤和纤维间压缩损伤4 种损伤模式,定义了与4 个损伤模式对应的损伤状态变量,导出了材料主轴系下损伤前后材料本构之间的关系. 损伤起始采用Puck 准则判定,损伤演化由特征长度内应变能释放密度控制. 假定材料服从线性应变软化行为,建立了损伤状态变量关于断裂面上等效应变的渐进损伤演化法则. 模型涵盖了复合材料面内损伤起始、演化直至最终失效的全过程. 完成了含孔[45/0/-45/90]_2S 层合板在拉伸和压缩载荷下失效分析,结果表明该模型能合理进行层合板的强度预测和损伤失效分析.     

独立失效模式多自由度随机滞回系统可靠性分析

基于Bouc-Wen滞回模型,研究了由滞回环本身的随机性导致的多自由度非线性随机系统可靠性分析问题。基于结构失效的首次穿越模型,应用四阶矩技术和Edgeworth级数逼近技术,对独立失效模式下多自由度随机滞回系统的可靠性问题进行分析。数值算例表明,由独立随机参数表征的随机结构,系统随机响应之间不再独立,存在协方差;系统响应之间相关系数不唯一,具有随时间连续变化的动态、强相关特性。分析计算结果与Monte-Carlo模拟结果吻合较好,表明算法能够满足工程计算精度要求。