碳纳米管增强复合材料圆锥薄壳非线性自由振动

考虑碳纳米管复合材料作为功能梯度材料的不均匀性,基于连续介质理论以及哈密尔顿变分原理,建立了功能梯度碳纳米管增强复合材料开口圆锥薄壳结构的非线性运动偏微分控制方程,然后利用Galerkin法,将非线性偏微分控制方程转化为常微分控制方程,进而采用谐波平衡法求解了开口圆锥壳的非线性自由振动问题,并探讨了圆锥薄壳几何参数、碳纳米管参数对结构非线性自由振动的影响．数值研究表明结构的无量纲非线性自由振动频率与线性自由振动频率的比值随圆锥薄壳长厚比的增大而变小、并随圆锥角的增大而变大．     

弹性地基中含孔隙的功能梯度圆锥壳的振动分析

为研究弹性地基中多孔功能梯度材料圆锥壳的振动特性,基于经典薄壳理论建立了弹性地基中含均匀和非均匀分布孔隙的功能梯度材料圆锥薄壳的振动方程,并用伽辽金法求得了自由振动和动力响应的解。通过参数分析讨论了孔隙、弹性地基参数、半锥角等因素对功能梯度圆锥壳自由振动和动力响应的影响。结果表明,弹性地基的压缩和剪切刚度的增大提高了圆锥壳的振动频率而显著减小了动力响应;当半锥角增大时,圆锥壳的动力响应显著增大。与非均匀分布孔隙壳体相比,均匀分布孔隙壳体的自振频率和动力响应随孔隙率的变化更为敏感。     

功能梯度圆锥扁壳的1:2内共振研究

对热载荷和机械载荷共同作用下的功能梯度圆锥扁壳进行了1:2内共振分析。假设材料属性与温度有关,材料组分沿厚度方向呈幂律梯度变化,基于一阶剪切变形理论和von-Karman几何非线性关系,运用Hamilton原理建立功能梯度圆锥扁壳的非线性动力学方程;采用Galerkin法将运动控制方程离散成一个两自由度非线性动力学系统,采用多尺度法对上述方程进行摄动分析,获得了系统的平均方程,进一步得到频率响应函数和力幅响应函数。研究了材料体积分数指数和面内载荷对幅-频响应特性的影响,结果表明:研究可以得出:改变材料体积分数指数会影响材料中金属的含量及分布,从而引起幅-频响应曲线刚度特性和共振峰带宽的变化;面内载荷的变化不会影响幅-频响应曲线的刚度特性,但是会改变共振峰的带宽。本文还研究了振幅跳跃现象,通过Runge-Kutta法对共振系统进行数值仿真,研究了面内载荷对系统非线性动力学行为的影响,得出:随着面内载荷的变化,系统的运动从周期运动经历概周期运动变成混沌运动。     

带初始几何缺陷FGM固支圆柱壳的非线性动力学分析

本文主要研究了带初始几何缺陷的功能梯度固支圆柱壳在不同体积分数下的非线性动力学行为。假定该功能梯度圆柱壳材料的组分是沿厚度的方向呈梯度几何变化的。运用经典板壳理论、von-Karman几何非线性应变位移关系以及Hamilton原理,推导出两端固支FGM圆柱壳的偏微分非线性运动控制方程。本文考虑了圆柱壳的对称模态,利用Galerkin法对上述非线性动力学方程进行截断,得到常微分形式的非线性动力学方程。主要运用Runge-Kutta法进行数值仿真,并且画出了其最大lyapunov指数图,主要研究了面内载荷对振动响应的影响,并对比了不同体积分数对系统非线性动力学的影响。     

热环境中功能梯度圆形薄板的混沌运动

针对陶瓷-金属功能梯度圆板,同时考虑几何非线性、材料物性参数随温度变化且材料组分沿厚度方向按幂律分布的情况,应用虚功原理给出了热载荷与横向简谐载荷共同作用下的非线性振动偏微分方程。在固支无滑动的边界条件下,通过引入位移函数,利用伽辽金方法得到了达芬型非线性动力学方程。利用Melnikov方法,给出了热环境中功能梯度圆板可能发生混沌运动的临界条件。通过数值算例,给出了不同体积分数指数和温度的同宿分岔曲线,平面相图和庞加莱映射图,讨论其对临界条件的影响,证实了系统混沌运动的存在。通过分岔图和与其相对应的最大李雅普诺夫指数图,分析了激励频率和激励幅值对倍周期分岔的影响及变化规律,发现系统可出现周期、倍周期和混沌等复杂动力学响应。     

功能梯度旋转圆板的热弹性固有振动

在考虑热因素及旋转运动条件下，针对金属－陶瓷功能梯度圆板的固有振动问题进行研究．给出随温度变化且材料组分沿厚度方向按幂律分布的材料物性参数，依据热弹性理论得到圆板的能量关系式．基于哈密顿原理建立旋转金属－陶瓷功能梯度圆板热弹性动力学方程．采用伽辽金法得到边界约束下圆板的自由振动方程，确定了静挠度及固有振动频率．基于数值计算，得到系统固有频率值随体积分数指数、转速和温度等参量的变化曲线，讨论了静挠度变化规律及动力系统的奇点稳定性问题．结果表明，固有频率随体积分数指数、材料表面温度以及转速的增加而减小．     

热环境中旋转运动功能梯度圆板的强非线性固有振动

研究热环境中旋转运动功能梯度圆板的非线性固有振动问题．针对金属－陶瓷功能梯度圆板,考虑几何非线性、材料物理属性参数随温度变化以及材料组分沿厚度方向按幂律分布的情况,应用哈密顿原理推得热环境中旋转运动功能梯度圆板的非线性振动微分方程．考虑周边夹支边界条件,利用伽辽金法得到了横向非线性固有振动方程,并确定了静载荷引起的静挠度．用改进的多尺度法求解强非线性方程,得出非线性固有频率表达式．通过算例,分析了旋转运动功能梯度圆板固有频率随转速、温度等参量的变化情况．结果表明,非线性固有频率随金属含量的增加而降低;随转速和圆板厚度的增大而升高;随功能梯度圆板表面温度的升高而降低．     

热环境中旋转运动功能梯度圆板的强非线性固有振动

研究热环境中旋转运动功能梯度圆板的非线性固有振动问题．针对金属－陶瓷功能梯度圆板，考虑几何非线性、材料物理属性参数随温度变化以及材料组分沿厚度方向按幂律分布的情况，应用哈密顿原理推得热环境中旋转运动功能梯度圆板的非线性振动微分方程．考虑周边夹支边界条件，利用伽辽金法得到了横向非线性固有振动方程，并确定了静载荷引起的静挠度．用改进的多尺度法求解强非线性方程，得出非线性固有频率表达式．通过算例，分析了旋转运动功能梯度圆板固有频率随转速、温度等参量的变化情况．结果表明，非线性固有频率随金属含量的增加而降低；随转速和圆板厚度的增大而升高；随功能梯度圆板表面温度的升高而降低．     

功能梯度锥-柱连接壳的环向自由振动分析

论文旨在分析功能梯度锥-柱连接壳的环向自由振动,以提高其结构的振动性能和稳定性.采用Voigt模型和四参数幂函数体积分数描述功能梯度材料属性,基于Donnell薄壳理论推导出锥壳和柱壳的位移与应变关系,分别得出锥壳和柱壳的能量表达式.引入人工弹簧模拟边界和壳体间的连接条件,依据Chebyshev多项式构造位移函数,基于Rayleigh-Ritz法求解FGMs锥-柱连接壳模态频率,分析梯度指数、边界条件和几何参数对模态频率的影响.结果表明：增加陶瓷体积分数能有效提高结构的模态频率,而增大梯度指数则会降低结构的模态频率;边界约束条件越强,FGMs锥-柱连接壳的模态频率越高;随着环向波数的增大,边界条件对结构模态频率的影响越来越弱,边界约束效果作用于圆柱壳明显强于圆锥壳;当环向波数大于3时,随着壳体厚度增大,结构的模态频率呈线性提高,而增大锥柱壳长度比会降低结构模态频率;在锥柱壳长度比一定时,随着锥角的增大会使结构的模态频率先增加到峰值后减小.     

弹性支撑功能梯度微圆柱壳模态频率的研究

在建立弹性支撑功能梯度薄壁微圆柱壳模型的基础上,基于修正的偶应力理论和一阶剪切变形理论,推导了微圆柱壳的模态频率方程,讨论了弹性支撑、尺寸效应、温度梯度、材料组分指数、孔隙以及几何尺寸等参数对微圆柱壳模态频率的影响。结果表明：微尺度下,弹性刚度系数在0～10⁵ N/m³范围内对微圆柱壳的模态频率基本无影响,剪切刚度系数在0～5×10⁴ N/m范围内对模态频率的影响较大,且增大剪切刚度系数有益于提高微圆柱壳的模态频率;由修正的偶应力理论得到的模态频率大于由经典连续体理论得到的模态频率;在弹性支撑和尺寸效应有无考虑的4种组合下,模态频率随温度梯度和微圆柱壳长度的增大而减小,随陶瓷体积分数指数的增大而增大,随孔隙体积分数和微圆柱壳厚度的变化规律不同;温度梯度对考虑尺寸效应或弹性基础的微圆柱壳模态频率影响较大,而孔隙调节具弹性支撑微圆柱壳的模态频率尤其显著。     

Nonlinear vibration of functionally graded graphene platelet-reinforced composite truncated conical shell using first-order shear deformation theory

In this study, the first-order shear deformation theory(FSDT) is used to establish a nonlinear dynamic model for a conical shell truncated by a functionally graded graphene platelet-reinforced composite(FG-GPLRC). The vibration analyses of the FG-GPLRC truncated conical shell are presented. Considering the graphene platelets(GPLs) of the FG-GPLRC truncated conical shell with three different distribution patterns, the modified Halpin-Tsai model is used to calculate the effective Young's modulus. Hamilton's principle, the FSDT, and the von-Karman type nonlinear geometric relationships are used to derive a system of partial differential governing equations of the FG-GPLRC truncated conical shell. The Galerkin method is used to obtain the ordinary differential equations of the truncated conical shell. Then, the analytical nonlinear frequencies of the FG-GPLRC truncated conical shell are solved by the harmonic balance method. The effects of the weight fraction and distribution pattern of the GPLs, the ratio of the length to the radius as well as the ratio of the radius to the thickness of the FG-GPLRC truncated conical shell on the nonlinear natural frequency characteristics are discussed. This study culminates in the discovery of the periodic motion and chaotic motion of the FG-GPLRC truncated conical shell.     

Imperfection sensitivity in the nonlinear vibration of functionally graded plates

In this paper, the nonlinear partial differential equations of nonlinear vibration for an imperfect functionally graded plate (FGP) in a general state of arbitrary initial stresses are presented. The derived equations include the effects of initial stresses and initial imperfections size. The material properties of a functionally graded plate are graded continuously in the direction of thickness. The variation of the properties follows a simple power-law distribution in terms of the volume fractions of the constituents. Using these derived governing equations, the nonlinear vibration of initially stressed FGPs with geometric imperfection was studied. Present approach employed perturbation technique, Galerkin method and Runge–Kutta method. The perturbation technique was used to derive the nonlinear governing equations. The equations of motion of the imperfect FGPs was obtained using Galerkin method and then solved by Runge–Kutta method. Numerical solutions are presented for the performances of perfect and imperfect FGPs. The nonlinear vibration of a simply supported ceramic/metal FGP was solved. It is found that the initial stress, geometric imperfection and volume fraction index greatly affect the behaviors of nonlinear vibration.     

Free vibration analysis of functionally graded laminated sandwich cylindrical shells integrated with piezoelectric layer

An analytical method for the three-dimensional vibration analysis of a functionally graded cylindrical shell integrated by two thin functionally graded piezoelectric (FGP) layers is presented. The first-order shear deformation theory is used to model the electromechanical system. Nonlinear equations of motion are derived by considering the von Karman nonlinear strain-displacement relations using Hamilton’s principle. The piezoelectric layers on the inner and outer surfaces of the core can be considered as a sensor and an actuator for controlling characteristic vibration of the system. The equations of motion are derived as partial differential equations and then discretized by the Navier method. Numerical simulation is performed to investigate the effect of different parameters of material and geometry on characteristic vibration of the cylinder. The results of this study show that the natural frequency of the system decreases by increasing the non-homogeneous index of FGP layers and decreases by increasing the non-homogeneous index of the functionally graded core. Furthermore, it is concluded that by increasing the ratio of core thickness to cylinder length, the natural frequencies of the cylinder increase considerably.     

热环境下功能梯度夹层双曲壳三维自由振动分析

功能梯度夹层双曲壳结构广泛应用在航空航天、海洋工程等领域中,对于该类结构的动力学特性研究非常重要。本文以热环境下功能梯度夹层双曲壳为研究对象,在三阶剪切变形理论的基础上,考虑横向拉伸作用的影响提出了一种新的位移场,假设材料的物性参数与温度有关,且沿厚度方向表示为幂律函数。利用Hamilton原理得到简支边界条件下功能梯度夹层双曲壳三维振动系统动力学方程,利用Navier法求得两种不同夹层类型的系统固有频率。研究了几何物理参数和温度场对功能梯度夹层双曲壳自由振动固有频率的影响。     

Free vibrations of four-parameter functionally graded parabolic panels and shells of revolution

Basing on the First-order Shear Deformation Theory (FSDT), this paper focuses on the dynamic behaviour of moderately thick functionally graded parabolic panels and shells of revolution. A generalization of the power-law distribution presented in literature is proposed. Two different four-parameter power-law distributions are considered for the ceramic volume fraction. Some symmetric and asymmetric material profiles through the functionally graded shell thickness are illustrated by varying the four parameters of power-law distributions. The governing equations of motion are expressed as functions of five kinematic parameters. For the discretization of the system equations the Generalized Differential Quadrature (GDQ) method has been used. Numerical results concerning four types of parabolic shell structures illustrate the influence of the parameters of the power-law distribution on the mechanical behaviour of shell structures considered.     

Thermal buckling and free vibration of FG truncated conical shells with stringer and ring stiffeners using differential quadrature method

In this paper, thermal buckling and free vibration of orthogonally stiffened functionally graded truncated conical shells in thermal environment is investigated. Conical shell has been stiffened by rings and stringers, and the influences of the stiffeners are evaluated by the aid of smearing method. The material properties of the structure are assumed to be changed continuously in the thickness direction. First, the initial thermal stresses are obtained accurately by solving the thermoelastic equilibrium equations. Then, by taking into account the initial thermal stresses, equations of motion as well as boundary conditions are obtained, applying the Hamilton’s principle and the first-order shear deformation theory. The natural frequencies of the system have been achieved, solving these governing equations with considering Differential Quadrature Method (DQM). In addition to Eigen frequency analysis, the critical buckling-temperature of the conical shell has been computed. Moreover, the effects of geometrical parameters, number of stiffeners, thermal environment and various boundary conditions on natural frequency of the system have been investigated. Finally, in order to validate the present work, the results are compared with those of other researches available in literature.