Rotational asymmetry of reactant concentration and its evolution in a circulating fluidized bed riser

Rotational asymmetric distribution of reactant (ozone) concentration and its evolution along with the gas-solid reactive flow were studied in a 76 mm i.d., 10.2 m high circulating fluidized bed (CFB) riser reactor. The superficial gas velocity ranged from 3 to 5 m/s and the solids circulation rates were 50 and 100 kg/(m² s). Experimental results show that the asymmetry of reactant distribution can extend to a height close to the length of flow developing zone of the CFB riser reactor and then disappears. Based on the hydrodynamics of the gas and solid phases in the solids entrance region, this asymmetry can be attributed to the effect of the solids entrance structure.     

Experimental investigation on flow asymmetry in solid entrance region of a square circulating fluidized bed

To study the influence of back feeding particles on gas-solid flow in the riser, this paper investigated the flow asymmetry in the solid entrance region of a fluidized bed by particle concentration/velocity measurements in a cold square circulating fluidized beds （CFB）. The pressure drop distribution along the riser and the saturation carrying capacity of gas for Geldart-B type particles were first analyzed. Under the condition of u0 = 4 m/s and Gs = 21 kg/（m^2 s）, the back feeding particles were found to penetrate the lean gas-solid flow near the entrance （rear） wall before reaching the opposite （front） wall, thus leading to a relatively denser region near the front wall in the bottom bed. Higher solid circulation rate （u0 =4 m/s, Gs = 33 kg/（m^2 s）） resulted in a higher particle concentration in the riser. However the back feeding particles with higher momentum increased the asymmetry of the particle concentration/velocity profile in the solid entrance region. Lower air velocity （u0 =3.2 m/s） and Gs =21 kg/（m2 s）, beyond the saturation carrying capacity of gas, induced an S-shaped axial solid distribution with a denser bottom zone. This limited the penetration of the back feeding particles and forced the flnidizing air to flow in the central region, thus leading to a higher solid holdup near the rear wall. Under the conditions of uo = 4 m/s and Gs = 21 kg/（m^2 s）, addition of coarse particles （dp= 1145 μm） into the bed made the radial distribution of solids more symmetrical.     

Design assessment of a 150 kWt CFBC Test Unit

For clean and efficient energy generation from coal, the most suitable technology known to date is ‘Fluidized Bed Combustion’ technology. Applications of circulating fluidized bed (CFB) combustion technology have been steadily increasing in both capacity and number over the past decade. Designs of these units have been based on the combustion tests carried out in pilot scale facilities to determine the combustion and desulfurization characteristics of coal and limestone reserves in CFB conditions. Similarly, utilization of Turkish lignites in CFB boilers necessitates adaptation of CFB combustion technology to these resources. However, the design of these test units are not based on firing coals with high ash, volatile matter and sulfur contents like Turkish lignites. For this purpose, a 150 kWt CFB combustor test unit is designed and constructed in Chemical Engineering Department of Middle East Technical University, based on the extensive experience acquired at the existing 0.3 MWt Bubbling Atmospheric Fluidized Bed Combustor (AFBC) Test Rig. Following the commissioning tests, a combustion test is carried out for investigation of combustion characteristics of Çan lignite in CFB conditions and for assessment of the design of test unit. Comparison of the design outputs with experimental results reveals that most of the predictions and assumptions have acceptable agreement with the operating conditions. In conclusion, the performance of 150 kWt CFBC Test Unit is found to be satisfactory to be utilized for the long term research studies on combustion and desulfurization characteristics of indigenous lignite reserves in circulating fluidized bed combustors.     

Effects of particle size and concentration on bubble coalescence and froth formation in a slurry bubble column

A new approach for simulating the formation of a froth layer in a slurry bubble column is proposed. Froth is considered a separate phase, comprised of a mixture of gas, liquid, and solid. The simulation was carried out using commercial flow simulation software (FIRE v2014) for particle sizes of 60–150 μm at solid concentrations of 0–40 vol%, and superficial gas velocities of 0.02–0.034 m/s in a slurry bubble column with a hydraulic diameter of 0.2 m and height of 1.2 m. Modelling calculations were conducted using a Eulerian–Eulerian multiphase approach with k–ε turbulence. The population balance equations for bubble breakup, bubble coalescence rate, and the interfacial exchange of mass and momentum were included in the computational fluid dynamics code by writing subroutines in Fortran to track the number density of different bubble sizes. Flow structure, radial gas holdup, and Sauter mean bubble diameter distributions at different column heights were predicted in the pulp zone, while froth volume fraction and density were predicted in the froth zone. The model was validated using available experimental data, and the predicted and experimental results showed reasonable agreement. To demonstrate the effect of increasing solid concentration on the coalescence rate, a solid-effect multiplier in the coalescence efficiency equation was used. The solid-effect multiplier decreased with increasing slurry concentration, causing an increase in bubble coalescence efficiency. A slight decrease in the coalescence efficiency was also observed owing to increasing particle size, which led to a decrease in Sauter mean bubble diameter. The froth volume fraction increased with solid concentration. These results provide an improved understanding of the dynamics of slurry bubble reactors in the presence of hydrophilic particles.     

One-dimensional interfacial area transport of vertical upward bubbly flow in narrow rectangular channel

The design and safety analysis for miniature heat exchangers, the cooling system of high performance microelectronics, research nuclear reactors, fusion reactors and the cooling system of the spallation neutron source targets requires the knowledge of the gas–liquid two-phase flow in a narrow rectangular channel. In this study, flow measurements of vertical upward air–water flows in a narrow rectangular channel with the gap of 0.993 mm and the width of 40.0 mm were performed at seven axial locations by using the imaging processing technique. The local frictional pressure loss gradients were also measured by a differential pressure cell. In the experiment, the superficial liquid velocity and the void fraction ranged from 0.214 m/s to 2.08 m/s and from 3.92% to 42.6%, respectively. The developing two-phase flow was characterized by the significant axial changes of the local flow parameters due to the bubble coalescence and breakup in the tested flow conditions. The existing two-phase frictional multiplier correlations such as Chisholm, 1967, Mishima et al., 1993 and Lee and Lee (2001) were verified to give a good prediction for the measured two-phase frictional multiplier. The predictions of the drift-flux model with the rectangular channel distribution parameter correlation of Ishii (1977) and several existing drift velocity correlations of Ishii, 1977, Hibiki and Ishii, 2003 and Jones and Zuber (1979) agreed well with the measured void fractions and gas velocities. The interfacial area concentration (IAC) model of Hibiki and Ishii (2002) was modified by taking the channel width as the system length scale and the modified IAC model could predict the IAC and Sauter mean diameter acceptably.     

Modeling and scale analysis of gaseous fuel reactors in chemical looping combustion systems

This work investigates the scale-up of chemical looping combustion (CLC), a next-generation technology for carbon capture and storage, to the industrial scale. The study focused on the bottom bed of the unit, which was considered to be the critical region during scale-up due to the large solids inventory in this zone combined with relatively inefficient gas–solids contact. Two CLC reactors of vastly different sizes (bench and utility scale) were studied to discern their difference related to scale-up via a one-dimensional model. This model considered kinetics that varied with the degree of oxidation and population distribution of the oxygen carriers, the mixing of which accounts for both convective and dispersive transport. The model was validated against bench scale data, and was used to evaluate the performance of a 1000 MW_th CLC fuel reactor using either syngas or methane as fuels. Sensitivity analyses were also carried out with this model to determine the effects of several parameters on fuel conversion, including solids circulation, oxygen carrier reactivity, bed height, and maximum bubble size. The results show that the mass transfer of gas from bubbles to the emulsion phase represents a significant limiting factor for fuel conversion in the bottom bed of a utility scale fuel reactor.     

Experimental and statistical assessments of the mechanical strength reliability of gamma alumina catalyst supports

The mechanical strength of solid catalysts is considered an important factor in terms of ensuring the reliable performance of industrial reactors. In this work, a pelletizing method was used to form gamma alumina support for catalysts. Response surface methodology (RSM) was employed to analyze and model the effects of various manufacturing parameters on the crushing strength of the supports. These parameters were binder concentration, compaction pressure, calcination temperature, and drying mode. The suggested model was verified by applying an analysis of variance to assess its validity with regard to crushing strength. The mechanical reliability of various supports was also determined by calculating their Weibull modulus values through linear regression of the Weibull equation. The material with the highest mechanical strength reliability will have both a high mean crushing strength and a high Weibull modulus, and the best values obtained for a support in this work were 70.7 MPa and 6.63, respectively. The conditions used to form this sample were: 20 mass% binder concentration, 861 MPa compaction pressure, 466 °C calcination temperature, and gentle drying.     

Computational investigation of hydrodynamics and cracking reaction in a heavy oil riser reactor

This paper presents a computational investigation of hydrodynamics, heat transfer and cracking reaction in a heavy oil riser operated in a novel operating mode of low temperature contact and high catalyst-to-oil ratio. Through incorporating feedstock vaporization and a 12-lump cracking kinetics model, a validated gas–solid flow model has been extended to the analysis of the hydrodynamic and reaction behavior in an industrial riser. The results indicate that the hydrodynamics, temperature and species concentration exhibit significantly nonuniform behavior inside the riser, especially in the atomization nozzle region. The lump concentration profiles along the riser height provide useful information for riser optimization. Compared to conventional fluid catalytic cracking (FCC) process, feedstock conversion and gasoline yield are respectively increased by 1.9 units and 1.0 unit in the new FCC process, the yield of liquefied petroleum gas is increased by about 1.0 unit while dry gas yield is reduced by about 0.3 unit.     

PIV, 2D-LIF and 1D-Raman measurements of flow field,composition and temperature in premixed gas turbine flames

Several laser diagnostic measurement techniques have been applied to study the lean premixed natural gas/air flames of an industrial swirl burner. This was made possible by equipping the burner with an optical combustion chamber that was installed in the high-pressure test rig facility at the DLR Institute of Combustion Technology in Stuttgart. The burner was operated with preheated air at various operating conditions with pressures up to p = 6 bar and a maximum thermal power of P = 1 MW.The instantaneous planar flow field inside the combustor was studied with particle image velocimetry (PIV). Planar laser induced fluorescence (PLIF) of OH radicals on a single-shot basis was used to determine the shape and the location of the flame front as well as the spatial distribution of reaction products. 1D laser Raman spectroscopy was successfully applied for the measurement of the temperature and the concentration of major species under realistic gas turbine conditions.Results of the flow field analysis show the shape and the size of the main flow regimes: the inflow region, the inner and the outer recirculation zone. The highly turbulent flow field of the inner shear layer is found to be dominated by small and medium sized vortices. High RMS fluctuations of the flow velocity in the exhaust gas indicate the existence of a rotating exhaust gas swirl. From the PLIF images it is seen that the primary reactions happened in the shear layers between inflow and the recirculation zones and that the appearance of the reaction zones changed with flame parameters. The results of the multiscalar Raman measurements show a strong variation of the local mixture fraction allowing conclusions to be drawn about the premix quality. Furthermore, mixing effects of unburnt fuel and air with fully reacted combustion products are studied giving insights into the processes of the turbulence–chemistry interaction.     

Preparation and gas sensing performances of palladium surface-modified flower-like SnO2 nanopowders

Flower-like SnO2 nanopowders prepared by a hydrothermal method were surface modified with palla- dium via impregnation. The crystal structure, morphology, and surface chemistry states of the samples were characterized by means of X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The gas sensing performances were also investigated. For a hydrothermal temperature of 220 ℃, flower-like SnO2 nanoparticles consist of nanorods with diameters of 40 nm and lengths of 100 nm. The XPS and XRD results reveal that palladium exists in the Pd0 chemical state but the crystal is too small to be detected. The 0.3 wt% Pd modified SnO2 sensor shows better sensi- tivity, up to 21, for 70 μL/L ethanol gas at an optimal working temperature of 250 ℃. The quick response time （3 s） and fast recovery time （-20 s） are the main characteristics of this sensor.     

Validated scale-up procedure to predict blockage condition for fluidized dense-phase pneumatic conveying systems

This paper presents results of an ongoing investigation into modelling fluidized dense-phase pneumatic conveying of powders. For the reliable design of dense-phase pneumatic conveying systems, an accurate estimation of the blockage boundary condition or the minimum transport velocity requirement is of sig- nificant importance. The existing empirical models for fine powder conveying in fluidized dense-phase mode are either based on only a particular pipeline and product or have not been tested for their accuracy under a wide range of scale-up conditions. In this paper, a validated test design procedure has been devel- oped to accurately scale-up the blockage boundary with the help of a modelling format that employs solids loading ratio and Froude number at pipe inlet conditions using conveying data of two different samples of fly ash, electro-static precipitation （ESP） dust and cement （particle densities： 2197-3637 kgJm3; loose poured bulk densities： 634-1070kg/m3; median size： 7-30 l~m）. The developed models （in power func- tion format） have been used to predict the blockage boundary for larger diameter and longer pipelines （e.g. models based on 69 mm I.D. ~ 168 m long pipe have been scaled up to 105 mm I.D. and 554 m length）. The predicted blockage boundaries for the scale-up conditions were found to provide better accuracy compared to the existing models.     

Euler-Euler CFD modeling of fluidized bed＂ Influence of specularity coefficient on hydrodynamic behavior

Euler-Euler two-fluid model is used to simulate the hydrodynamics of gas-solid flow in a bubbling flu- idized bed with Geldert B particles where the solid property is calculated by applying the kinetic theory of granular flow （KTGF）. Johnson and Jackson wall boundary condition is used for the particle phase, and different amount of slip between particle and wall is given by varying the specularity coefficient （φ） from 0 to 1. The simulated particle velocity, granular temperature and particle volume fraction are compared to investigate the effect of different wall boundary conditions on the hydrodynamic behavior, Some of the results are also compared with the available experimental data from the literature. It was found that the model predictions are sensitive to the specularity coefficient. The hydrodynamic behavior deviated sig- nificantly for φ = 0 and φ = 0.01 with maximum deviation found at φ = 0 i.e. free-slip condition. However, the overall bed height predicted by all the conditions is similar.     

Study on premixed combustion in cylindrical micro combustors: Transient flame behavior and wall heat flux

The micro combustor is a key component of the micro thermophotovoltaic (TPV) system. Improving the wall temperature of the micro combustor is an effective way to elevate the system efficiency. An experimental study on the wall temperature and radiation heat flux of a series of cylindrical micro combustors (with a backward-facing step) was carried out. For the micro combustors with d = 2 mm, the regime of successful ignition (under the cold wall condition) was identified for different combustor lengths. Acoustic emission was detected for some cases and the emitted sound was recorded and analyzed. Under the steady-state condition, the effects of the combustor diameter (d), combustor length (L), flow velocity (u₀) and fuel–air equivalence ratio (Ф) on the wall temperature distribution were investigated by measuring the detailed wall temperature profiles. In the case that the micro combustor is working as an emitter, the optimum efficiency was found at Ф ≈ 0.8, independent of the combustor dimensions (d and L) and the flow velocity. Under the experimental conditions employed in the present study, the positions of the peak wall temperature were found to be about 8–11 mm and 4–6 mm from the step for the d = 3 mm and d = 2 mm micro combustors, respectively, which are 8–11 and 8–12 times of their respective step heights. This result suggests that the backward-facing step employed in the combustor design is effective in stabilizing the flame position.     

CFD–DEM simulation of the pneumatic conveying of fine particles through a horizontal slit

Fine particles play a significant role in many industrial processes. To study the dynamic behavior of fine particle and their deposition in rock fractures, the pneumatic conveying of fine particles (approximately 100 μm in diameter) through a small-scale horizontal slit (0.41 m × 0.025 m) was studied, which is useful for the sealing technology of underground gas drainage in coal mining production. The CFD–DEM method was adopted to model the gas-particle two-phase flow; the gas phase was treated as a continuum and modeled using computational fluid dynamics (CFD), particle motion and collisions were simulated using the DEM code. Then, the bulk movement of fine particles through a small-scale horizontal slit was explored numerically, and the flow patterns were further investigated by visual inspection. The simulation results indicated that stratified flow or dune flow can be observed at low gas velocities. For intermediate gas velocities, the flow patterns showed pulsation phenomena, and dune flow reappeared in the tail section. Moreover, periodic flow regimes with alternating thick and sparse stream structures were observed at a high gas velocity. The simulation results of the bulk movement of fine particles were in good agreement with the experimental findings, which were obtained by video-imaging experiments. Furthermore, the calculated pressure drop versus gas velocity profile was investigated and compared with relative experimental findings, and the results showed good agreement. Furthermore, the particle velocity vectors and voidage distribution were numerically simulated. Selected stimulation results are presented and provide a reference for the further study of fine particles.     

Characterization of various structures in gas-solid fluidized beds by recurrence quantification analysis

Gas-solid fluidized beds are widely considered as nonlinear and chaotic dynamic systems. Pressure fluc- tuations were measured in a fluidized bed of 0.15 m in diameter and were analyzed using multiple approaches： discrete Fourier transform （DFT）, discrete wavelet transform （DWT）, and nonlinear recur- rence quantification analysis （RQA）. Three different methods proposed that the complex dynamics of a fluidized bed system can be presented as macro, meso and micro structures. It was found from DFT and DWT that a minimum in wide band energy with an increase in the velocity corresponds to the transition between macro structures and finer structures of the fluidization system. Corresponding transition veloc- ity occurs at gas velocities of 0.3, 0.5 and 0.6 m]s for sands with mean diameters of 150, 280 and 490/~m, respectively. DFT, DWT, and RQA could determine frequency range of0-3.125 Hz for macro, 3. ! 25-50 Hz for meso, and 50-200 Hz for micro structures. The RQA showed that the micro structures have the least periodicity and consequently their determinism and laminarity are the lowest. The results show that a combination of DFT, DWT, and RQA can be used as an effective approach to characterize multi-scale flow behavior in gas-solid fluidized beds.     

Particle number size distribution and new particle formation （NPF） in Lanzhou,Western China

Particle number size distribution from 10 to 10,000 nm was measured by a wide-range particle spectrometer (WPS-1000XP) at a downwind site north of downtown Lanzhou, western China, from 25 June to 19 July 2006. We first report the pollution level, diurnal variation of particle concentration in different size ranges and then introduce the characteristics of the particle formation processes, to show that the number concentration of ultrafine particles was lower than the values measured in other urban or suburban areas in previous studies. However, the fraction of ultrafine particles in total aerosol number concentration was found to be much higher. Furthermore, sharp increase of ultrafine particle concentration was frequently observed at noon. An examination of the diurnal pattern suggests that the burst of the ultrafine particles was mainly due to nucleation process. During the 25-day observation, new particle formation (NPF) from homogeneous nucleation was observed during 33% of the study period. The average growth rate of the newly formed particles was 4.4 nm/h, varying from 1.3 to 16.9 nm/h. The needed concentration of condensable vapor was 6.1 × 10⁷ cm^?3, and its source rate was 1.1 × 10⁶ cm^?3 s^?1. Further calculation on the source rate of sulphuric acid vapor indicated that the average participation of sulphuric acid to particle growth rate was 68.3%.     

A solids mixing rate correlation for small scale fluidized beds

A new first degree solids mixing rate is proposed to evaluate the mixing of solids in small scale fluidized beds. Particle mixing experiments were carried out in a 2D fluidized bed with a cross-section of 0.02 m × 0.2 m and a height of 1 m. White and black particles with average diameters of 850 and 450 μm were used in our experiments. Image processing was used to measure the concentration of the tracers at different times. The effects of four representative operating parameters (superficial gas velocity, ratio of tracer particles to bed particles, tracer particle position, and particle size) on mixing are discussed with reference to the mixing index. We found that the Lacey index depends on the concentration of the tracers. The position of the tracers affects the initial mixing rate but not the final degree of mixing. However, the new mixing rate equation does not depend on the initial configuration of the particles because this situation is considered to be the initial condition. Using the data obtained in this work and that found in literature, an empirical correlation is proposed to evaluate the mixing rate constant as a function of dimensionless numbers (Archimedes, Reynolds, and Froude) in small scale fluidized beds. This correlation allows for an estimation of the mixing rate under different operating conditions and for the detection of the end point and/or the time of mixing.     

A note on a boundary condition for spouted beds

The boundary condition, zero solids pressure at the top of a particle bed of maximum spoutable height, Hm, is shown to eliminate any resort to empiricism in the derivation of the fluid velocity in the annulus of a spouted bed for which both viscous and inertial effects are taken into account. The same boundary condition fails when applied to a spouted bed for which the bed height H 〈 Hm, especially when H 〈 0.8Hm.     

Transportation characteristics of gas–solid two-phase flow in a long-distance pipeline

In this study, experiments on fly ash conveying were carried out with a home-made long-distance positive-pressure pneumatic conveying system equipped with a high performance electrical capacitance tomography system to observe the transient characteristics of gas–solid two-phase flow. The experimental results indicated that solids throughput increased with increasing solids–gas ratio when the conveying pipeline was not plugged. Moreover, the optimum operating state was determined for the 1000 m long conveying pipeline with a throttle plate of 26 orifices. At this state the solids throughput was about 12.97 t/h. Additionally, the transportation pattern of fly ash gradually changed from sparse–dense flow to partial and plug flows with increasing conveying distance because of the conveying pressure loss. These experimental results provide important reference data for the development of pneumatic conveying technology.     

Optimized synthesis and photovoltaic performance of TiO2 nanoparticles for dye-sensitized solar cell

This paper presents response surface methodology （RSM） as an efficient approach for modeling and optimizing TiO2 nanoparticles preparation via co-precipitation for dye-sensitized solar cell （DSSC） perfor- mance. Titanium （IV） bis-（acetylacetonate） di-isopropoxide （DIPBAT）, isopropanol and water were used as precursor, solvent and co-solvent, respectively. Molar ratio of water, aging temperature and calcina- tion temperature as preparation factors with main and interaction effects on particle characteristics and performances were investigated, Particle characteristics in terms of primary and secondary sizes, crys- tal orientation and morphology were determined by X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. Band gap energy and power conversion efficiency of DSSCs were used for perfor- mance studies. According to analysis of variance （ANOVA） in response surface methodology （RSM）, all three independent parameters were statistically significant and the final model was accurate. The model predicted maximum power conversion efficiency （0.14%） under the optimal condition of molar ratio of DIPBAT-to-isopropanol-to-water of 1 ： 10：500, aging temperature of 36 C and calcination temperature of 400 ℃. A second set of data was adopted to validate the model at optimal conditions and was found to be 0.14 ± 0.015%, which was very close to the predicted value. This study proves the reliability of the model in identi（ving the optimal condition for maximum performance.