Mean and turbulent velocity measurements of supersonic mixing layers

The behavior of supersonic mixing layers under three conditions has been examined by schlieren photography and laser Doppler velocimetry. In the schlieren photographs, some large-scale, repetitive patterns were observed within the mixing layer; however, these structures do not appear to dominate the mixing layer character under the present flow conditions. It was found that higher levels of secondary freestream turbulence did not increase the peak turbulence intensity observed within the mixing layer, but slightly increased the growth rate. Higher levels of freestream turbulence also reduced the axial distance required for development of the mean velocity. At higher convective Mach numbers, the mixing layer growth rate was found to be smaller than that of an incompressible mixing layer at the same velocity and freestream density ratio. The increase in convective Mach number also caused a decrease in the turbulence intensity ( _u/U).List of symbols a speed of sound - b total mixing layer thickness between U ₁ – 0.1 U and U ₂ + 0.1 U - f normalized third moment of u-velocity, f u³/(U)³ - g normalized triple product of u² , g u²/(U)³ - h normalized triple product of u ², h u ²/(U)³ - l _u axial distance for similarity in the mean velocity - l _u axial distance for similarity in the turbulence intensity - M Mach number - M _c convective Mach number (for ₁ = ₂), M _c (U ₁ – U ₂)/(a ₁ + a ₂) - P static pressure - r freestream velocity ratio, r U ₂/U ₁ - Re unit Reynolds number, Re U/ - s freestream density ratio, s ₂/₁ - T _t total temperature - u instantaneous streamwise velocity - u deviation of u-velocity, uu – U - U local mean streamwise velocity - U ₁ primary freestream velocity - U ₂ secondary freestream velocity - average of freestream velocities, (U ₁ + U ₂)/2 - U freestream velocity difference, U U ₁ – U ₂ - instantaneous transverse velocity - v deviation of -velocity, – V - V local mean transverse velocity - x streamwise coordinate - y transverse coordinate - y ₀ transverse location of the mixing layer centerline - ensemble average - ratio of specific heats - boundary layer thickness (y-location at 99.5% of free-stream velocity) - similarity coordinate, (y – y ₀)/b - compressible boundary layer momentum thickness - viscosity - density - standard deviation - dimensionless velocity, (U – U ₂)/U - 1 primary stream - 2 secondary stream A version of this paper was presented at the 11th Symposium on Turbulence, October 17–19, 1988, University of Missouri-Rolla     

Die Torsionsspannungen in Wellen mit tiefen Längsnuten

Übersicht MitF(x, y) als Spannungsfunktion einer Welle ohne Nut und(, y) als Potentialfunktion des Quelle-Senke-Systems erhält man Spannungsfunktionen(, y) =F(x, y) –(, y) für Wellen mit tiefen Längsnuten. Es wird gezeigt, daß sich damit die Schubspannungen in den Läufern von Schraubenverdichtern ermitteln lassen.

---

Shearing stresses in shafts with deep longitudinal grooves

Summary The stress functions(, y) of shafts with deep longitudinal grooves may be represented by(, y) =F(x, y) –(, y) whereF(x, y) is the stress function of a cylindrical shaft without grooves and(, y) denotes the potential function of the source-sink system. It is shown that the shearing stresses in rotors of screw-compressors may be obtained in this way.

     

The dynamic and steady shear properties of synovial fluid and of the components making up synovial fluid

Steady-shear and dynamic properties of a pooled sample of cattle synovial fluid have been measured using techniques developed for low viscosity fluids. The rheological properties of synovial fluid were found to exhibit typical viscoelastic behaviour and can be described by the Carreau type A rheological model. Typical model parameters for the fluid are given; these may be useful for the analysis of the complex flow problems of joint lubrication.The two major constituents, hyaluronic acid and proteins, have been successfully separated from the pooled sample of synovial fluid. The rheological properties of the hyaluronic acid and the recombined hyaluronic acid-protein solutions of both equal and half the concentration of the constituents found in the original synovial fluid have been measured. These properties, when compared to those of the original synovial fluid, show an undeniable contribution of proteins to the flow behaviour of synovial fluid in joints. The effect of protein was found to be more prominent in hyaluronic acid of half the normal concentration found in synovial fluid, thus providing a possible explanation for the differences in flow behaviour observed between synovial fluid from certain diseased joints compared to normal joint fluid.Nomenclature A Ratio of angular amplitude of torsion head to oscillation input signal - G Storage modulus - G Loss modulus - I Moment of inertia of upper platen — torsion head assembly - K Restoring constant of torsion bar - N ₁ First normal-stress difference - R Platen radius - S ⁽ⁱ⁾ Geometric factor in the dynamic property analysis - t ₁ Characteristic time parameter of the Carreau model - X, Y Carreau model parameters - Z () Reimann Zeta function of - Carreau model parameter - Shear rate - Apparent steady-shear viscosity - ^* Complex dynamic viscosity - Dynamic viscosity - Imaginary part of the complex dynamic viscosity - ₀ Zero-shear viscosity - ₀ Cone angle - Carreau model characteristic time - Density of fluid - Shear stress - Phase difference between torsion head and oscillation input signals - ₀ Zero-shear rate first normal-stress coefficient - Oscillatory frequency     

Flow in vicinity of blunt body stagnation point in diverging hypersonic stream

In the hypersonic thin shock layer approximation for a small ratio k of the densities before and after the normal shock wave the solution of [1] for the vicinity of the stagnation point of a smooth blunt body is extended to the case of nonuniform outer flow. It is shown that the effect of this nonuniformity can be taken into account with the aid of the effective shock wave radius of curvature R_*, whose introduction makes it possible to reduce to universal relations the data for different nonuniform outer flows with practically the same similarity criterion k. The results of the study are compared with numerical calculations of highly underexpanded jet flow past a sphere.Notations x, y a curvilinear coordinate system with axes directed respectively along and normal to the body surface with origin at the forward stagnation point - R radius of curvature of the meridional plane of the body surface - uV, vV., , p V ² respectively the velocity projections on the x, y axes, density, and pressure - and V freestream density and velocity The indices =0 and=1 apply to plane and axisymmetric flows Izv. AN SSSR, Mekhanika Zhidkosti i Gaza, Vol. 5, No. 3, pp. 102–105, 1970.     

A three-parameter model describing the experimental relation between shear stress and shear rate for laminar flow of aqueous polymer solutions

Summary A three-parameter model is introduced to describe the shear rate — shear stress relation for dilute aqueous solutions of polyacrylamide (Separan AP-30) or polyethylenoxide (Polyox WSR-301) in the concentration range 50 wppm – 10,000 wppm. Solutions of both polymers show for a similar rheological behaviour. This behaviour can be described by an equation having three parameters i.e. zero-shear viscosity ₀, infinite-shear viscosity , and yield stress ₀, each depending on the polymer concentration. A good agreement is found between the values calculated with this three-parameter model and the experimental results obtained with a cone-and-plate rheogoniometer and those determined with a capillary-tube rheometer.

---

Zusammenfassung Der Zusammenhang zwischen Schubspannung und Schergeschwindigkeit von strukturviskosen Flüssigkeiten wird durch ein Modell mit drei Parametern beschrieben. Mit verdünnten wäßrigen Polyacrylamid-(Separan AP-30) sowie Polyäthylenoxidlösungen (Polyox WSR-301) wird das Modell experimentell geprüft. Beide Polymerlösungen zeigen im untersuchten Schergeschwindigkeitsbereich von ein ähnliches rheologisches Verhalten. Dieses Verhalten kann mit drei konzentrationsabhängigen Größen, nämlich einer Null-Viskosität ₀, einer Grenz-Viskosität und einer Fließgrenze ₀ beschrieben werden. Die Ergebnisse von Experimenten mit einem Kegel-Platte-Rheogoniometer sowie einem Kapillarviskosimeter sind in guter Übereinstimmung mit den Werten, die mit dem Drei-Parameter-Modell berechnet worden sind.

---

a Pa^–1 physical quantity defined by:a = {1 – ( / ₀)}/ ₀ - c l concentration (wppm) - D m capillary diameter - L m length of capillary tube - P Pa pressure drop - R m radius of capillary tube - u m s^–1 average velocity - v _r m s^–1 local axial velocity at a distancer from the axis of the tube - shear rate (–dv _r /dr) - local shear rate in capillary flow - s^–1 wall shear rate in capillary flow - Pa s dynamic viscosity - _a Pa s apparent viscosity defined by eq. [2] - ( _a ) Pa s apparent viscosity in capillary tube at a distanceR from the axis - ₀ Pa s zero-shear viscosity defined by eq. [4] - Pa s infinite-shear viscosity defined by eq. [5] - l ratior/R - kg m^– density - Pa shear stress - ₀ Pa yield stress - _r Pa local shear stress in capillary flow - _R Pa wall shear stress in capillary flow _R = (PR/2L) - _v m³ s^–1 volume rate of flow With 8 figures and 1 table     

Measurement of the relaxation time in Darcy flow

The inertia of a liquid flowing through a porous medium is normally ignored, but if the acceleration is great, it may be important. The relaxation time, defined so that it alone accounts for the inertia, has been determined experimentally with a simple oscillator. A U-Tube is provided with a porous plug and filled with a liquid. During pendulation of the liquid, the frequency and the damping define the relaxation time. The measured value of the relaxation time is about 10 times the theoretical estimate derived from Navier-Stokes equation.Symbols E modulus of elasticity - E _D dissipated energy - E _k kinetic energy - g acceleration of gravity - G pressure gradient - h height - K ₀ permeability - L length of porous plug - n porosity - P dissipated power - pressure - R half the tube length - R _c radius of the tube bend - r radial coordinate - r _o radius of the tube - s coordinate along a streamline in the tube - t time - v flux per unit area - it relaxation time - , auxiliary variables - , v dynamic and kinematic viscosity - , velocity potential for inviscid flow and gravity potential - dissipation function - displacement of the liquid - , _o frequency of damped and undamped oscillations     

Reservoir transport equations by compositional approach

The objective of this paper is to present an overview of the fundamental equations governing transport phenomena in compressible reservoirs. A general mathematical model is presented for important thermo-mechanical processes operative in a reservoir. Such a formulation includes equations governing multiphase fluid (gas-water-hydrocarbon) flow, energy transport, and reservoir skeleton deformation. The model allows phase changes due to gas solubility. Furthermore, Terzaghi's concept of effective stress and stress-strain relations are incorporated into the general model. The functional relations among various model parameters which cause the nonlinearity of the system of equations are explained within the context of reservoir engineering principles. Simplified equations and appropriate boundary conditions have also been presented for various cases. It has been demonstrated that various well-known equations such as Jacob, Terzaghi, Buckley-Leverett, Richards, solute transport, black-oil, and Biot equations are simplifications of the compositional model.Notation List B reservoir thickness - B formation volume factor of phase - Cⁱ mass of component i dissolved per total volume of solution - C ⁱ mass fraction of component i in phase - C heat capacity of phase at constant volume - C_p heat capacity of phase at constant pressure - D ⁱ hydrodynamic dispersion coefficient of component i in phase - D_MTf thermal liquid diffusivity for fluid f - F = F(x, y, z, t) defines the boundary surface - f_p fractional flow of phase - g gravitational acceleration - H_p enthalpy per unit mass of phase - J_p volumetric flux of phase - k_rf relative permeability to fluid f - k₀ absolute permeability of the medium - M_p ⁱ mass of component i in phase - n porosity - N rate of accretion - P_f pressure in fluid f - p_ca capillary pressure between phases and =p-p - Rⁱ rate of mass transfer of component i from phase to phase - Rⁱ _source source rate of component i within phase - S saturation of phase - s gas solubility - T temperature - t time - U displacement vector - u velocity in the x-direction - v velocity in the y-direction - V volume of phase - V_s velocity of soil solids - W_i body force in coordinate direction i - x horizontal coordinate - z vertical coordinate Greek Letters _p volumetric coefficient of compressibility - _T volumetric coefficient of thermal expansion - _ij Kronecker delta - volumetric strain - _m thermal conductivity of the whole matrix - internal energy per unit mass of phase - gf suction head - density of phase - _ij tensor of total stresses - _ij tensor of effective stresses - volumetric content of phase - f viscosity of fluid f     

Mixed convection flow in narrow vertical ducts

The mixed convection flow in a vertical duct is analysed under the assumption that , the ratio of the duct width to the length over which the wall is heated, is small. It is assumed that a fully developed Poiseuille flow has already been set up in the duct before heat from the wall causes this to be changed by the action of the buoyancy forces, as measured by a buoyancy parameter . An analytical solution is derived for the case when the Reynolds numberRe, based on the duct width, is of 0 (1). This is extended to the case whenRe is 0 (^–1) by numerical integrations of the governing equations for a range of values of representing both aiding and opposing flows. The limiting cases, || 1 andR=Re of 0 (1), andR and both large, with of 0 (R ^1/3) are considered further. Finally, the free convection limit, large with R of 0 (1), is discussed.

---

Mischkonvektion in engen senkrechten Rohren

Zusammenfassung Mischkonvektion in einem senkrechten Rohr wird unter der Voraussetzung untersucht, daß das Verhältnis der Rohrbreite zur Länge, über welche die Wand beheizt wird, klein ist. Es wird angenommen, daß sich bereits eine voll entwickelte Poiseuille-Strömung in dem Rohr eingestellt hat, bevor Antriebskräfte, gemessen mit dem Auftriebsparameter , aufgrund der Wandbeheizung die Strömung verändern. Es wird eine analytische Lösung für den Fall erhalten, daß die mit der Rohrbreite als charakteristische Länge gebildete Reynolds-ZahlRe konstant ist. Dies wird mittels einer numerischen Integration der wichtigsten Gleichungen auf den FallRe =f (^–1) sowohl für Gleich- als auch für Gegenstrom ausgedehnt. Weiterhin werden die beiden Grenzfälle betrachtet, wenn || 1 undR=Re konstant ist, sowieR und beide groß mit proportionalR ^1/3. Schließlich wird der Grenzfall der freien Konvektion, großes mit konstantem R, diskutiert.

---

Nomenclature g acceleration due to gravity - Gr Grashof number - G modified Grashof number - h duct width - l length of the heated section of the duct wall - p pressure - Pr Prandtl number - Q flow rate through the duct - Q ₀ heat transfer on the wally=0 - Q ₁ heat transfer on the wally=1 - Re Reynolds number - R modified Reynolds number - T temperature of the fluid - T ₀ ambient temperature - T applied temperature difference - u, velocity component in thex-direction - v, velocity component in they-direction - x, co-ordinate measuring distance along the duct - y, co-ordinate measuring distance across the duct - buoyancy parameter - ₀ modified buoyancy parameter, ₀=R ^–1/3 - coefficient of thermal expansion - ratio of duct width to heated length, =h/l - (non-dimensional) temperature - _w applied temperature on the wally=0 - kinematic viscosity - density of the fluid - ₀ shear stress on the wally=0 - ₁ shear stress on the wally=1 - stream function     

Nonlinear rheological behavior of a concentrated spherical silica suspension

Linear and nonlinear viscoelastic properties were examined for a 50 wt% suspension of spherical silica particles (with radius of 40 nm) in a viscous medium, 2.27/1 (wt/wt) ethylene glycol/glycerol mixture. The effective volume fraction of the particles evaluated from zero-shear viscosities of the suspension and medium was 0.53. At a quiescent state the particles had a liquid-like, isotropic spatial distribution in the medium. Dynamic moduli G^* obtained for small oscillatory strain (in the linear viscoelastic regime) exhibited a relaxation process that reflected the equilibrium Brownian motion of those particles. In the stress relaxation experiments, the linear relaxation modulus G(t) was obtained for small step strain (0.2) while the nonlinear relaxation modulus G(t, ) characterizing strong stress damping behavior was obtained for large (>0.2). G(t, ) obeyed the time-strain separability at long time scales, and the damping function h() (–G(t, )/G(t)) was determined. Steady flow measurements revealed shear-thinning of the steady state viscosity () for small shear rates (< ^–1; = linear viscoelastic relaxation time) and shear-thickening for larger (>^–1). Corresponding changes were observed also for the viscosity growth and decay functions on start up and cessation of flow, + (t, ) and _– (t, ). In the shear-thinning regime, the and dependence of ₊(t,) and _–(t,) as well as the dependence of () were well described by a BKZ-type constitutive equation using the G(t) and h() data. On the other hand, this equation completely failed in describing the behavior in the shear-thickening regime. These applicabilities of the BKZ equation were utilized to discuss the shearthinning and shear-thickening mechanisms in relation to shear effects on the structure (spatial distribution) and motion of the suspended particles.Dedicated to the memory of Prof. Dale S. Parson     

On laminar flow through a uniformly porous pipe

Numerous investigations ([1] and [4–9]) have been made of laminar flow in a uniformly porous circular pipe with constant suction or injection applied at the wall. The object of this paper is to give a complete analysis of the numerical and theoretical solutions of this problem. It is shown that two solutions exist for all values of injection as well as the dual solutions for suction which had been noted by previous investigators. Analytical solutions are derived for large suction and injection; for large suction a viscous layer occurs at the wall while for large injection one solution has a viscous layer at the centre of the channel and the other has no viscous layer anywhere. Approximate analytic solutions are also given for small values of suction and injection.

Nomenclature

General r distance measured radially - z distance measured along axis of pipe - u velocity component in direction of z increasing - v velocity component in direction of r increasing - p pressure - density - coefficient of kinematic viscosity - a radius of pipe - V velocity of suction at the wall - r ²/a ² - R wall or suction Reynolds number, Va/ - f() similarity function defined in (6) - u ₀() eigensolution - U(0) a velocity at z=0 - K an arbitrary constant - B _K Bernoulli numbers Particular Section 5 perturbation parameter, –2/R - ² a constant, –K - x / - g(x) f()/ Section 6 perturbation parameter, –R/2 - ² a constant, –K - g() f() - g _c ()=g() near centre of pipe - * point where g()=0 Section 7 2/R - ² K - t (1–)/ - w(t, ) [1–f(t)]/ - ₀, ₁ constants - g() f()– ₀ - ₀/ - ₀ a constant - * point where f()=0     

Beitrag zur Prüfung metallischer Werkstoffe im Torsionsversuch

Zusammenfassung Der Torsionsversuch eignet sich zur Untersuchung des plastischen Verhaltens von Metallen bei erhöhten Temperaturen, wenn die Fließspannung stark von der Umformgeschwindigkeit abhängt. Aus der gemessenen Drehmoment-Drehwinkel-Kurve wird die Fließkurvek _f () berechnet. Hierfür wird ein Fließkriterium benötigt, dessen Unsicherheit im allgemeinen größer ist als alle Meßfehler. Diese Unsicherheit geht aber nicht in die berechnete Dehngeschwindigkeitsempfindlichkeit ein, die somit als Hauptergebnis des Versuches anzusehen ist.Um die Bedingungen technischer Warmumformung zu simulieren, wird die Verwendung extrem kurzer Proben (flacher Scheiben) empfohlen, womit sehr hohe Umformgeschwindigkeiten erreicht werden können. Für die Auswertung derartiger Versuche ist die wirksame Länge der kurzen Proben — experimentell oder semiempirisch — zu bestimmen und die Kerbwirkung zu berücksichtigen. Im Gegensatz zur herkömmlichen Vorgehensweise wird empfohlen, die örtliche Spannung und Verzerrung nicht für die Mantelfläche der Probe zu berechnen, sondern für einen kritischen Radialabstand im Innern der Probe, für den die Schiebung von der Kerbwirkung unabhängig ist, so daß sich die zuverlässigsten Werte ergeben.

---

Summary The torsion test is often used for studying the plastic deformation of metals at elevated temperatures when stress depends strongly on the strain rate. From the measured torque-twisting angle curve, the stress-strain curvek _f () has to be calculated. For this purpose a yield criterion has to be used the uncertaintly of which normally exceeds all experimental errors. This uncertaintly, however, does not propagate into the calculated strain rate sensitivity which therefore may be considered as the main result of the torsion test.For simulating the conditions of technical hot forming processes, the use of extremely short test pieces (flat discs) by which very high strain rates can be obtained is recommended. For evaluating the test data the efficient lenght of short specimens has to be determined. In opposition to the conventional procedure of test evaluation, it is recommended not to calculate stress and strain for the surface of the specimen but for a critical radius for which strain is independent of the notch effect so that the most reliable values are obtained.

Mit 5 Abbildungen     

Rheologie pathologischer Gelenkflüssigkeiten

Zusammenfassung Die eingehende Analyse des viskoelastischen Verhaltens von 193 Kniegelenkspunktaten verschiedenster entzündlicher und nichtentzündlicher Gelenkerkrankungen ließ keine wesentlichen diagnostischen Hilfen für klinische Problemfälle erkennen. Untersucht wurden im einzelnen Fließkurven einschließlich der Anfangsviskosität ₀ und durch eine Normierungsmethode ermittelte master-curves, sowie Normalspannungen und in 3 Fällen gleichzeitig auch der SpeichermodulG und der VerlustmodulG mit Hilfe von dynamischen Messungen.Durch Vergleich der pathologischen Gelenkpunktate mit normaler, post mortal gewonnener gepoolter Synovia ließ sich ein Eindruck vom Grad der gestörten Viskoelastizität gewinnen. Dabei lassen die erniedrigten Hyaluronsäure-Konzentrationen, die Veränderungen der konzentrationsunabhängigen Knickzeitt _k> und die master-curve erkennen, daß hierfür sowohl eine verringerte Konzentration als auch ein geringeres Molekulargewicht der Hyaluronsäure verantwortlich ist. Konzentrierungsversuche pathologischer Synovia ergaben den Hinweis auf die Entstehung von Mikrogelen und ließen in Fällen zuvor fehlender Normalspannungen auch nach der Eindickung keine Normalspannungen erkennen. Es wird deshalb auch die Möglichkeit gestörter intermolekularer Interaktionen in der pathologischen Synovia diskutiert.

---

Summary A thorough analysis of the viscoelastic behaviour of 193 synovial fluid samples of knee joints concerning different joint diseases (inflammatory and non-inflammatory) gives no essential diagnostic help in case of clinical problems.Investigations were done particularly on flow curves including the Newtonian viscosity ₀ and normal forces, and with the help of a standardization-method we got master curves. In three cases we also got dynamic properties i.e. the elastic modulusG and the loss modulusG. By comparison of the pathological synovial fluid samples with normal, post-mortem pooled synovial fluid one gets an idea of the degree of disturbance on viscoelasticity. It was found that the reduced concentration and the lower molecular weight of the hyaluronic acid are responsible for the pathological variation of the concentration independent bending timet _k as well as the shape of the master curves.Tests on concentrated pathological synovial fluids indicate the beginning formation of micro-gels. In cases of absence of normal forces even after concentration no normal forces could be detected. Therefore the possibility of disturbed intermolecular interactions in pathological synovial fluids will be discussed, too.

---

D Schergeschwindigkeit - D _K D-Koordinate des Tangentenschnittpunktes - t _k Knickzeit - s Steigung des geradlinigen Anteils der Fließkurve - scheinbare Viskosität - _m mittlere Viskosität beiD = 10² s^–1 - ₀ Anfangsviskosität, Nullviskosität - Endviskosität - _{N 11} – ₂₂ 1. Normalspannungsdifferenz - G ₀ Ruheschermodul - G ^* komplexer (dynamischer) Schermodul - G Speichermodul - G Verlustmodul - Winkelgeschwindigkeit - Winkel der Phasendifferenz - Kegelwinkel - d Durchmesser von Kegel und Platte des Meßsystems - f Frequenz der vorgegebenen Oszillation - f _n Eigenfrequenz des Torsionskopfes - _IA Amplitude der Eingangsschwingung - _TA Amplitude der Ausgangsschwingung - _I axiale Bewegung der Schneckenwelle - _T Bewegung des Torsionskopfverminderers - [] Grenzviskositätszahl (Staudinger-Index) - v Verhängungszahl - r Korrelationskoeffizient - m Mittelwert - s Standardabweichung - p Signifikanzniveau - n.s. nicht signifikant p > 0,05 Auszugsweise vorgetragen auf der Jahrestagung der Deutschen Rheologischen Gesellschaft in Berlin vom 8.–10. Mai 1978.Mit 9 Abbildungen und 8 Tabellen     

Transport in ordered and disordered porous media I: The cellular average and the use of weighting functions

In this work we consider transport in ordered and disordered porous media using singlephase flow in rigid porous mediaas an example. We defineorder anddisorder in terms of geometrical integrals that arise naturally in the method of volume averaging, and we show that dependent variables for ordered media must generally be defined in terms of thecellular average. The cellular average can be constructed by means of a weighting function, thus transport processes in both ordered and disordered media can be treated with a single theory based on weighted averages. Part I provides some basic ideas associated with ordered and disordered media, weighted averages, and the theory of distributions. In Part II a generalized averaging procedure is presented and in Part III the closure problem is developed and the theory is compared with experiment. Parts IV and V provide some geometrical results for computer generated porous media.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A_e area of entrances and exits for the-phase contained within the macroscopic system, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor, m² - L general characteristic length for volume averaged quantities, m - characteristic length (pore scale) for the-phase - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - N unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p0 reference pressure in the-phase, N/m² - p traditional intrinsic volume averaged pressure, N/m² - r0 radius of a spherical averaging volume, m - r position vector, m - r position vector locating points in the-phase, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v traditional superficial volume averaged velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V/V, volume average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

On surface waves in generalized thermoelasticity

Knowles' representation theorem for harmonically time-dependent free surface waves on a homogeneous, isotropic elastic half-space is extended to include harmonically time-dependent free processes for thermoelastic surface waves in generalized thermoelasticity of Lord and Shulman and of Green and Lindsay.r , , r , , .This work was done when author was unemployed.     

Deformation to breaking of deep water gravity waves

The results of laboratory observations of the deformation of deep water gravity waves leading to wave breaking are reported. The specially developed visualization technique which was used is described. A preliminary analysis of the results has led to similar conclusions than recently developed theories. As a main fact, the observed wave breaking appears as the result of, first, a modulational instability which causes the local wave steepness to approach a maximum and, second, a rapidly growing instability leading directly to the breaking.List of symbols L total wave length - H total wave height - crest elevation above still water level - trough depression below still water level - wave steepness =H/L - crest steepness =/L - trough steepness =/L - F ₁ forward horizontal length from zero-upcross point (A) to wave crest - F ₂ backward horizontal length from wave crest to zero-downcross point (B) - crest front steepness =/F ₁ - crest rear steepness =/F ₂ - vertical asymmetry factor=F ₂/F ₁ (describing the wave asymmetry with respect to a vertical axis through the wave crest) - µ horizontal asymmetry factor=/H (describing the wave asymmetry with respect to a horizontal axis: SWL) - T ₀ wavemaker period - L ₀ theoretical wave length of a small amplitude sinusoïdal wave generated at T _inf0 ^sup–1 frequency - ₀ average wave height     

Heat transfer from laminar flow in ducts with elliptic cross-section

Summary The cooling of a hot fluid in laminar Newtonian flow through cooled elliptic tubes has been calculated theoretically. Numerical data have been computed for the two values 1.25 and 4 of the axial ratio of the elliptic cross-section . For =1.25 the influence of non-zero thermal resistance between outmost fluid layer and isothermal surroundings has also been investigated. Special attention has been given to the distribution of heat flux around the perimeter; when increases the flux varies more with the position at the circumference. This positional dependence becomes less pronounced, however, as the (position-independent) thermal resistance of the wall increases.Flattening of the conduit, while maintaining its cross-sectional area constant, improves the cooling. Comparison with rectangular pipes shows that this improvement is not as marked with elliptic as with rectangular pipes.Nomenclature A _k =A _{m, n} coefficients of expansion (6) - a, b half-axes of ellipse, b<a - a _p =a _{r, s} coefficients of representation (V) - D hydraulic diameter, = 4S/P; S = cross-sectional area, P = perimeter - D _e equivalent diameter, according to (13) - n coordinate (outward) normal to the tube wall - T temperature of fluid - T _i temperature of fluid at the inlet - T _s temperature of surroundings - v ₀ mean velocity of fluid - v _z longitudinal velocity of fluid - x, y carthesian coordinates coinciding with axes of ellipse - z coordinate in flow direction - , dimensionless half-axes of ellipse, =a/D and =b/D - _t heat transfer coefficient from fluid at bulk temperature to surroundings; equation (11) - _w heat transfer coefficient at the wall; equation (3) - axial ratio of ellipse, = a/b = / - , , , dimensionless coordinates; =x/D, =y/D, =z/D, =n/D - dimensionless temperature, = (T–T _s)/(T _i–T _s) - ₀ cup-mixing mean value of ; equation (10) - thermal conductivity of fluid - _m,n = _k eigenvalue - c volumetric heat capacity of fluid - _{m, n} = _k = _k eigenfunction; equations (6) and (I) - Nu total Nusselt number, = _t D/ - Nusselt number at large distance from the inlet - Nu _w wall Nusselt number, = _w D/, based on _w - Pé Péclet number, = ₀ Dc/     

Mathematics and Rheology

Summary The great advances made in Rheology during the last forty years owe much to the application of mathematics. But in some cases, there have been misunderstandings. As a result, rheologists have sometimes been unnecessarily restricted. Mathematics is limited only by self-consistency: Rheology deals with the physical world.In particular, three terms are discussed: infinity, zero and negative, all of which have at least two meanings which have been confused. Rheological phenomena cannot be explained merely by mathematical formulation. Unnecessary mathematics should be avoided but professional rheologists must not shirk mathematics.This paper was read in an abbreviated form, at aConference of the British Society of Rheology in April 1971 The Proceedings were not published.     

Rheological properties of reactive polymer melts.

A new method for describing the rheological properties of reactive polymer melts, which was presented in an earlier paper, is developed in more detail. In particular, a detailed derivation of the equation of a first-order rheometrical flow surface is given and a procedure for determining parameters and functions occurring in this equation is proposed. The experimental verification of the presented approach was carried out using our data for polyamide-6.Notation E Dimensionless reduced viscosity, eq. (34) - E ₀ Newtonian asymptote of the function (36) - E power-law asymptote of the function (36) - E _{= 1} the value ofE at = 1 - k degradation reaction rate constant, s^–1 - k ₁ rate constant of function (t), eq. (26), s^–1 - k ₂ rate constant of function (t), eq. (29), s^–1 - K(t) residence-time-dependent consistency factor, eq. (22) - M _w weight-average molecular weight - M _x x-th moment of the molecular weight distribution - R gas constant - S _x M _x /M _w - t residence time in molten state, s - t _j thej-th value oft, s - T temperature, K - % MathType!MTEF!2!1!+-% feaafiart1ev1aaatCvAUfeBSjuyZL2yd9gzLbvyNv2CaerbuLwBLn% hiov2DGi1BTfMBaeXatLxBI9gBaerbd9wDYLwzYbItLDharqqtubsr% 4rNCHbGeaGqiVu0Je9sqqrpepC0xbbL8F4rqqrFfpeea0xd9vqpe0x% c9q8qqaqFn0dXdir-xcvk9pIe9q8qqaq-xir-f0-yqaqVeLsFr0-vr% 0-vr0db8meaabaqaciGacaGaaeqabaWaaeaaeaaakeaaieGaceWFZo% Gbaiaaaaa!3B4E!\[\dot \gamma \] shear rate, s^–1 - _i thei-th value of , s^–1 - _r =1 the value of at = 1, s^–1 - ^* reduced shear rate, eq. (44), s^–1 - dimensionless reduced shear rate, eq. (35) - viscosity, Pa · s - shear-rate and residence-time dependent viscosity, Pa · s - zero-shear-rate degradation curve - degradation curve at - _{t0 (t)} zero-residence-time flow curve - Newtonian asymptote of the RFS - instantaneous flow curve - power-law asymptote of the RFS - _0,0 zero-shear-rate and zero-residence-time viscosity, Pa · s - _E=1 value of viscosity atE=1, Pa · s - ^* reduced viscosity, eq. (43), Pa · s - zero-residence-time rheological time constant, s - density, kg/m³ - (t),(t) residence time functions     

Filament stretching equation in Lagrangian coordinates

The general integral of the very simple equation ^21/n/() was found to describe the cross sectional area of filaments of isothermal power law fluids while in transient stretching where is time and is the initial location of fluid molecules at time = 0 given as the distance from a reference point fixed in space. Any such stretching transient given as a solution of the above equation is physically realizable subject to the restrictions > 0 and/ < 0.     

A Strongly Degenerate Quasilinear Equation: the Parabolic Case

We prove the existence and uniqueness of entropy solutions of the Neumann problem for the quasilinear parabolic equation u_t=÷ a(u, Du), where a(z,)=f(z,), and f is a convex function of with linear growth as ||||, satisfying other additional assumptions. In particular, this class includes the case where f(z,)=(z)(), >0, and is a convex function with linear growth as ||||.