爆炸应力波作用下动、静裂纹相互作用的实验研究

采用数字激光动态焦散线测试系统,研究爆炸应力波作用下动裂纹与预制静裂纹(水平夹角为90°、150°)相互作用机理,以及裂纹扩展的动态行为。结果表明:(1)在动、静裂纹贯通之前,静裂纹两端便出现焦散斑,动、静裂纹贯通以后,静裂纹沿爆炸应力波传播方向扩展,并且扩展速度小于动裂纹扩展速度,也小于无静裂纹时动裂纹扩展速度; (2)静裂纹存在时,动裂纹扩展的总体长度减小。动裂纹起裂时间缩短,扩展速度基本不受静裂纹的影响,裂纹应力强度因子值大于静裂纹两端值; (3)随着静裂纹水平夹角的增大,动、静裂纹贯通时动裂纹沿水平方向偏转距离增大,静裂纹B端反向扩展与动裂纹相互“咬合”,C端裂纹扩展位移和速度增大。     

三点弯曲试样动态应力强度因子计算研究

利用Hopkinson压杆对三点弯曲试样进行冲击加载,采集了垂直裂纹面距裂尖2mm和与裂纹面成60°距裂尖5mm处的应变信号。根据裂尖附近测试的应变信号计算试样的动态应力强度因子,并与有限元计算结果进行比较,结果表明由于裂尖有一段疲劳裂纹区,通过裂尖附近应变信号来计算动态应力强度因子时,如果裂尖位置确定不准及粘贴应变片位置不够准确对计算结果将带来很大影响。因此利用应变片法计算动态应力强度因子时,为了获得更准确的计算结果,在实验后应对试件裂纹面进行分析测量,重新确定裂尖位置,必要时需对应变片至裂尖距离进行修正后再计算动态应力强度因子值。     

Dynamic stress intensity factor K III and dynamic crack propagation characteristics of anisotropic materials

Based on the mechanics of anisotropic materials, the dynamic propagation problem of a mode Ⅲ crack in an infinite anisotropic body is investigated. Stress, strain and displacement around the crack tip are expressed as an analytical complex function, which can be represented in power series. Constant coefficients of series are determined by boundary conditions. Expressions of dynamic stress intensity factors for a mode Ⅲ crack are obtained. Components of dynamic stress, dynamic strain and dynamic displacement around the crack tip are derived. Crack propagation characteristics are represented by the mechanical properties of the anisotropic materials, i.e., crack propagation velocity M and the parameter ~. The faster the crack velocity is, the greater the maximums of stress components and dynamic displacement components around the crack tip are. In particular, the parameter α affects stress and dynamic displacement around the crack tip.     

冲击载荷下扩展裂纹尖端动态能量释放率分布的焦散线分析

借助高速摄影捕捉裂纹瞬态扩展过程，利用动态焦散线研究了含有裂纹的三点弯曲梁在冲击载荷作用下扩展裂纹尖端的动态能量释放率分布规律；综合分析了裂纹扩展时间、长度、速度，以及扩展裂纹尖端动态应力强度因子与它的变化关系，表明了动态能量释放率在裂纹扩展过程中的驱动作用。     

采用压缩单裂纹圆孔板确定岩石动态起裂、扩展和止裂韧度

爆炸、冲击、地震等人为或自然灾害不可避免,经常造成大量土木工程设施的破坏,因此岩石在动态载荷作用下的行为受到特别关注.岩石动态断裂韧度是评价岩石抵抗裂纹动态起裂、扩展和止裂性能的材料参数,开展岩石动态断裂韧度测试方法的研究对相关理论基础和实验技术的要求较高.岩石动态断裂韧度分为动态起裂、动态扩展、动态止裂三种,虽然关于动态起裂和动态扩展的研究已有一些成果,对岩石动态止裂的研究仍是一个难题,至今几乎无人问津.研究表明,在分离式霍普金森压杆撞击压缩单裂纹圆孔板岩石试样的I型动态断裂试验中,动态起裂、扩展、止裂的全过程可以由黏贴在压缩单裂纹圆孔板试样上的裂纹扩展计监测,岩石的动态起裂、扩展、止裂韧度可以用实验-数值-解析法确定.特别值得一提的是首次测出了岩石的动态止裂韧度.裂纹扩展计信号还显示,压缩单裂纹圆孔板在止裂后,停止的裂纹还会再次动态起裂、扩展并超出裂纹扩展计的检测范围.从能量的角度分析了动态止裂的过程,指出测试动态止裂韧度时要注意的一些问题.结果显示,岩石动态起裂韧度和动态扩展韧度分别随动态加载率和裂纹扩展速度的增大而增大,岩石动态起裂韧度略大于动态止裂韧度.      

冲击载荷下含空孔三点弯曲梁的动态断裂行为

为得到圆孔缺陷对运动裂纹扩展过程的影响规律,采用动态焦散线实验方法进行模型实验,研究了冲击载荷下含空孔三点弯曲梁的动态断裂行为。研究结果表明:空孔对裂纹扩展有极大的阻碍作用,在一定范围内,空孔直径越大,阻碍作用越明显。裂纹扩展到空孔附近时,扩展速度会下降。裂纹在空孔上部再次起裂后,最大扩展速度远远大于裂纹与空孔贯通前的最大扩展速度。裂纹扩展至空孔附近时,裂纹尖端动态应力强度因子KdⅠ和KdⅡ均会下降。裂纹在空孔上部再次起裂后,裂尖的应力强度因子KdⅠ和KdⅡ均大于裂纹与空孔贯通前裂尖的KdⅠ和KdⅡ。在整个扩展过程中,裂纹尖端的动态应力强度因子KdⅡ远小于KdⅠ,说明KdⅠ在裂纹扩展过程中起主要作用。     

用裂纹张开位移计算三点弯曲试样的动态应力强度因子

给出了一种由裂纹的动态张开位移计算三点弯曲试样的动态应力强度因子的简单方法。对于两种不同几何尺寸的试样,在三类不同载荷作用下给出了数植算例,并与完全的动态有限元方法的计算结果进行了比较。结果表明:两种方法的计算结果相当一致。最后,还给出了由测定三点弯曲试样的裂纹张开位移确定试样的动态应力强度因子,最终确定材料动态起裂韧性的方法。     

平面应变下紧凑拉伸试样的动态断裂韧性的实验研究

材料的动态断裂韧性是衡量材料在动载荷作用下抵杭裂纹扩展能力的重要指标,以往的材料动态断裂韧性测试多采用三点弯曲试样,而针对紧凑拉伸试样的动态断裂韧性研究很少.本文将紧凑拉伸试样(即CT试样)简化成等效弹簧质量模型,得到了CT试样动态应力强度因子的近似表达式.对Hopkinson压杆装置进行了改进,利用改进后的实验装置进...     

含偏置裂纹三点弯曲梁的动态断裂行为研究

采用动态焦散线方法，对含偏置裂纹三点弯曲梁承受横向冲击的弯曲断裂行为进行了一系列动态断裂力学实验研究，分析了无量纲量ａ／ｌ的改变（ａ——初始裂纹偏离梁中心线的距离；ｌ——梁长度的一半）对于裂纹动态扩展行为（裂纹起始状态、裂纹尖端的复合应力强度因子、裂纹扩展速度、裂纹扩展轨迹）的影响，并借助动态光弹性应力分析，对应力波与扩展裂纹的相互作用以及应力波传播规律进行探讨．给出了裂纹尖端复合应力强度因子、裂纹扩展速度的变化、裂纹曲裂轨迹以及方向与梁中应力波传播的相互关系     

Experimental method of dynamic caustics and its application in fracture mechanics

The equation of static and dynamic caustics, and the formulae determining the position of crack tip and stress intensity factor are given. It is proven that for the case of low speed of crack propagation the static formula is applicable in calculation. A simple method to measure the static stress-optical constants is proposed. An Optical system which is suitable for the experiments of dynamic caustics was set-up and used to study the fracture in beam and rings with initial crack under impact loading. A series of dynamic caustics' photographs and curves showing the variations of corresponding crack lengths and dynamic stress intensity factors with time, are presented.     

Dynamic stress intensity factor KⅢ and dynamic crack propagation characteristics of anisotropic materials

Based on the mechanics of anisotropic materials,the dynamic propagation problem of a mode Ⅲ crack in an infinite anisotropic body is investigated.Stress,strain and displacement around the crack tip are expressed as an analytical complex function,which can be represented in power series.Constant coefficients of series are determined by boundary conditions.Expressions of dynamic stress intensity factors for a mode Ⅲ crack are obtained.Components of dynamic stress,dynamic strain and dynamic displacement around the crack tip are derived.Crack propagation characteristics are represented by the mechanical properties of the anisotropic materials,i.e.,crack propagation velocity M and the parameter α.The faster the crack velocity is,the greater the maximums of stress components and dynamic displacement components around the crack tip are.In particular,the parameter α affects stress and dynamic displacement around the crack tip.     

拱形试件动态断裂的动光弹分析

本文采用动光弹方法,分析了对带边裂纹的拱形三点弯曲试件在抢击加载条件下的瞬态反应。从多火花动光弹仪记录下来的16幅断裂过程的照片和微机输出的电火花光信号图上,得到了各时刻的等差线图形和裂纹长度。使用运动裂纹尖端附近的应力场解,去计算动应力强度因子。对环氧树脂材料,测定了动态应力强度因子与裂纹扩展速度之间的关系,并给出了当裂纹扩展速度达到410m/s时,为裂纹产生分叉的条件。     

应力波载荷作用下线弹性断裂过程的动态分析方法研究

利用Hopkinson单压杆实验装置 ,对材料的线弹性动态断裂特性进行了研究 ,建立了应力波载荷作用下动态裂纹起裂及扩展过程的动态分析方法 ,采用该方法可同时测得材料的动态裂纹起裂时间、断裂韧性和裂纹扩展速度。40Cr钢三点弯曲试样的实验结果表明 :该钢的动态裂纹扩展过程主要是减速过程 ,在2 2 5TPam /s的加载速率下 ,起裂时间为 2 8 0 0 s,最大裂纹扩展速度为 478 91m/s ,动态断裂韧性为6 3 12MPam。     

EXPERIMENTAL AND THEORETICAL INVESTIGATIONS ON THE VELOCITY OSCILLATIONS OF DYNAMIC CRACK PROPAGATING IN BRITTLE MATERIAL TENSION

设计了一种精确测量裂纹在预拉伸带板中的传播速度的实验装置, 系统研究了裂纹在受不同预加载荷作用的不同尺寸的有机玻璃 板中的传播行为.实验结果表明:在一个细长、上下表面固定的带板中, 裂纹速度分为加速和稳定2个阶段.在稳定速度阶段, 裂纹平均速度v₀ 是预加载荷在板中储存的弹性能Wh的增函数.由于此时裂纹处于自相似传播阶段, 可以认为材料的动态断裂能G_c是裂纹传播速度v₀的增函数, 即材料存在"速度增韧性".当裂纹传播速度达到一定阈值, 裂纹的传播速度出现明显的振荡现象, 裂纹的振荡周期与断裂面出现的周期性沟槽的尺度一致.在更高的预加能量下, 裂纹传播路径出现弯曲、微分岔以及宏观分岔现象.建立了一个描述裂纹在带板中的直线传播行为的动力学模型, 并用这个模型模拟裂纹在传播过程中的速度振荡现象.     

界面裂纹尖端的动态奇异特性

本文研究了界面裂纹尖端的动态应力场的奇异特性.引入尖端无摩擦接触的界面裂纹模型并采用具有运动边界的控制积分方程.证明了在动态界面裂纹尖端仅存在平方根奇异的应力场.数值结果表明接触区中的正应力确保持为压应力.为表现界面裂纹的动态特性,给出了应力强度因子和裂纹面接触区尺寸的数值结果.     

Determination of the dynamic stress intensity factorsK I d andK II d,for a mixed-mode propagating crack

In this paper, the dynamic propagation problem of a mixed-mode crack was studied by means of the experimental method of caustics. The initial curve and caustic equations were derived under the mixed-mode dynamic condition. A multi-point measurement method for determining the dynamic stress intensity factors,K _I ^d , andK _II ^d , and the position of the crack tip was developed. Several other methods were adopted to check this method, and showed that it has a good precision. Finally, the dynamic propagating process of a mixed-mode crack in the three-point bending beam specimen was investigated with our method.     

Experimental study on crack curving propagation in bending beams under impulsive load

Dynamic fracture behaviour of crack curving in bent beams has been investigated. In order to understand the propagation mechanism of such cracks under impact, an experimental method is used that combines dynamic photoelasticity with dynamic caustics to study the interaction of the flexural waves and the crack. From the state change of the transient stresses in polymer specimen, the curving fracture in the impulsively loaded beams is analyzed. The dynamic responses of crack tips are evaluated by the stress intensity factors for the cracks running in varying curvature paths under bending stress wave. The project supported by the National Natural Science Foundation of China and the Scientific Commission of Yunnan Province of China     

The singularity behavior of an interface crack under a dynamic load

The singularity behavior of a crack on the interface of two different media under dynamic load is investigated. By introducing a small region in which the crack faces make frictionless contact and making use of a kind of integral equations with moving boundaries, it is proved that there are only square-root singularities near the interface crack tips in case that a dynamic load acts on it. Numerical results show that the normal stress in the contact region remains negative. The results of the stress intensity factor and the length of the crack face contact region are given to illustrate the dynamic behavior of the interface crack.This work is supported by the National Natural Science Foundation of China.     

STUDY ON DYNAMIC STRESS INTENSITY FACTORS OF DISK WITH A RADIAL EDGE CRACK SUBJECTED TO EXTERNAL IMPULSIVE PRESSURE

A dynamic weight function method is presented for dynamic stress intensity factors of circular disk with a radial edge crack under external impulsive pressure. The dynamic stresses in a circular disk are solved under abrupt step external pressure using the eigenfunction method. The solution consists of a quasi-static solution satisfying inhomogeneous boundary conditions and a dynamic solution satisfying homogeneous boundary conditions. By making use of Fourier-Bessel series expansion, the history and distribution of dynamic stresses in the circular disk are derived. Furthermore, the equation for stress intensity factors under uniform pressure is used as the reference case, the weight function equation for the circular disk containing an edge crack is worked out, and the dynamic stress intensity factor equation for the circular disk containing a radial edge crack can be given. The results indicate that the stress intensity factors under sudden step external pressure vary periodically with time, and the ratio of the maximum value of dynamic stress intensity factors to the corresponding static value is about 2.0.     

Three-dimensional elliptic crack under impact loading

The dynamic stress intensity factor of a three-dimensional elliptic crack under impact loading is determined with the finite element method. The computation results can take into account the influence of time and the ratio of the wave speeds on the stress intensity factor. The present method is suitable not only for three-dimensional dynamic crack, but also for three-dimensional dynamic contact. Project supported by the National Natural Science Foundation of China (No. K19672007).