Effects of selenium treatment on composition and photoluminescence properties of porous silicon

In this work, an ultrasonically enhanced anodic electrochemical etching is developed to fabricate light-emitting porous silicon material. Porous silicon layer is fabricated in n-type (1 0 0) oriented silicon using HF solution and treated in selenious acid to increase the photoluminescence intensity. It is found that the increase of photoluminescence intensity after selenious acid treatment is higher in the intact zones and lower in the detached zones of ultrasonic excitation. The photoluminescence appears as a non-monotonous function of time exposure of selenious acid treatment. Surface chemical composition analysis by X-ray photoelectron spectroscopy shows formation of Si-Se_x and Si-Se_x-O_y on the surface of porous silicon treated with the selenious acid.     

Study and applications of plasma-modified Si and porous Si surfaces

In this work we have studied the electrical, chemical and physical properties of CH_x/silicon and CH_x/porous silicon (PS). The hydrocarbon (CH_x) layer has been deposited by plasma of methane under argon atmosphere. Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) Spectroscopy and photoluminescence have been used to characterize the CH_x/p-Si, CH_x/PS interfaces and, electrolyte/(CH_x/p-Si) and CH_x/PS/p-Si structures. The results show that in the case of bare silicon, the CH_x layers act as a resistant film to HF electrolyte and can be used as a potential tool for ultra-low thickness for masking and patterning. The deposition of CH_x layer on PS shows that CH_x/PS/p-Si structure presents a rectifying behaviour and can be used for detecting low concentration of large variety of gases. In addition CH_x coated PS samples exhibit more intense luminescence than that observed from an uncoated PS surface where red luminescence is shown .In conclusion, the results clearly demonstrate the interest and applications of Si and PS electrodes coated with hydrocarbon groups.     

Thermal annealing dependence of some optical properties of plasma-modified porous silicon

The photoluminescence and reflectance of porous silicon (PS) with and without hydrocarbon (CH_x) deposition fabricated by plasma enhanced chemical vapour deposition (PECVD) technique have been investigated. The PS samples were then, annealed at temperatures between 200 and 800 °C. The influence of thermal annealing on optical properties of the hydrocarbon layer/porous silicon/silicon structure (CH_x/PS/Si) was studied by means of photoluminescence (PL) measurements, reflectivity and ellipsometry spectroscopy. The composition of the PS surface was monitored by transmission Fourier transform infrared (FTIR) spectroscopy. Photoluminescence and reflectance measurements were carried out before and after annealing on the carbonized samples for wavelengths between 250 and 1200 nm. A reduction of the reflectance in the ultraviolet region of the spectrum was observed for the hydrocarbon deposited polished silicon samples but an opposite behaviour was found in the case of the CH_x/PS ones. From the comparison of the photoluminescence and reflectance spectra, it was found that most of the contribution of the PL in the porous silicon came from its upper interface. The PL and reflectance spectra were found to be opposite to one another. Increasing the annealing temperature reduced the PL intensity and an increase in the ultraviolet reflectance was observed. These observations, consistent with a surface dominated emission process, suggest that the surface state of the PS is the principal determinant of the PL spectrum and the PL efficiency.     

Structural and photoluminescence properties of thermally evaporated Cd1−xMnxS nano-crystalline films

Thin films of Cd_1−xMn_xS (0≤x≤0.5) were formed on glass substrates by resistive vacuum thermal evaporation. All the films were deposited at 300 K and the films were annealed at 373, 473 and 573 K for 1 h in a vacuum of 10⁻⁶ mbar. Atomic force microscopy (AFM) studies showed that all the films investigated were in nano-crystalline form with a grain size in the range 36-82 nm. All the films exhibited a wurtzite structure of the host material. The lattice parameters varied linearly with composition following Vegard’s law in the entire composition range. Photoluminescence studies showed that two distinct emission bands were observed for each Cd_1−xMn_xS compound. One corresponds to internal transition and the other one is due to the transition of Mn²⁺ ions in interstitial sites or in small ‘Mn’ chalcogenic clusters.     

Photovoltaic quantum efficiency enhancement by light harvesting of organo-lanthanide complexes

An increase of about 1% of the delivered power by a mono-crystalline commercial silicon solar cell has been obtained by coating the cell with an active poly-vinylacetate film doped with a light harvesting phenanthroline-Eu³⁺ complex. The dopant absorbs the UV component of the solar spectrum, where the silicon-based cells are almost blind, and emits red light that can be converted with an efficiency close to the maximum. This effect, achieved by a low cost encapsulation process, has been proven for the case of Air Mass 0 lighting conditions, and could be exploited also for terrestrial applications with the proper choice of the organic ligand.     

Room temperature photoluminescence from amorphous silicon nanoparticles in SiOx thin films

Amorphous SiO_x thin films with four different oxygen contents (x=1.15, 1.4, 1.5, and 1.7) have been prepared by thermal evaporation of SiO in vacuum and then annealed at 770 or 970 K in argon for various times ?40 min. The influence of annealing conditions and the initial film composition on photoluminescence (PL) from the annealed films has been explored. Intense room temperature PL has been observed from films with x?1.5, visible with a naked eye. It has been shown that PL spectra of most samples consists of two main bands: (i) a ‘green’ band centered at about 2.3 eV, whose position does not change with annealing conditions and (ii) an ‘orange-red’ band whose maximum moves from 2.1 to 1.7 eV with increasing annealing time and temperature and decreasing initial oxygen content. These observations have been explained assuming recombination via defect states in the SiO_x matrix for the first band and emission from amorphous Si nanoparticles for the second one.     

Structural and optical properties of a-Si1−xCx:H films synthesized by dc magnetron sputtering technique

Hydrogenated amorphous SiC films (a-Si_1−xC_x:H) were prepared by dc magnetron sputtering technique on p-type Si(1 0 0) and corning 9075 substrates at low temperature, by using 32 sprigs of silicon carbide (6H-SiC). The deposited a-Si_1−xC_x:H film was realized under a mixture of argon and hydrogen gases. The a-Si_1−xC_x:H films have been investigated by scanning electronic microscopy equipped with an EDS system (SEM-EDS), X-ray diffraction (XRD), secondary ions mass spectrometry (SIMS), Fourier transform infrared spectroscopy (FTIR), UV-vis-IR spectrophotometry, and photoluminescence (PL). XRD results showed that the deposited film was amorphous with a structure as a-Si_0.80C_0.20:H corresponding to 20 at.% carbon. The photoluminescence response of the samples was observed in the visible range at room temperature with two peaks centred at 463 nm (2.68 eV) and 542 nm (2.29 eV). In addition, the dependence of photoluminescence behaviour on film thickness for a certain carbon composition in hydrogenated amorphous SiC films (a-Si_1−xC_x:H) has been investigated.     

Modulation of the photoluminescence of Si quantum dots by means of CO2 laser pre-annealing

Si quantum dots (QDs) embedded in SiO₂ can be normally prepared by thermal annealing of SiO_x (x < 2) thin film at 1100 °C in an inert gas atmosphere. In this work, the SiO_x thin film was firstly subjected to a rapid irradiation of CO₂ laser in a dot by dot scanning mode, a process termed as pre-annealing, and then thermally annealed at 1100 °C for 1 h as usual. The photoluminescence (PL) intensity of Si QD was found to be enhanced after such pre-annealing treatment. This PL enhancement is not due to the additional thermal budget offered by laser for phase separation, but attributed to the production of extra nucleation sites for Si dots within SiO_x by laser irradiation, which facilitates the formation of extra Si QDs during the subsequent thermal annealing.     

A combinatorial approach to the discovery and optimization of YCa4O(BO3)3-based luminescent materials

Thin films of YCa₄O(BO₃)₃ (YCOB)-based new luminescent materials were explored by the combinatorial pulsed laser deposition (PLD) method which enabled us to fabricate continuous composition spread film libraries. Strong red and green luminescence were found in the Y_1−xEu_xCOB (0 ≤ x ≤ 1), (YEuCOB) and Y_1−yTb_yCOB (0 ≤ y ≤ 1) (YTbCOB) films, respectively. The film libraries were characterized by photoluminescence (PL), PL decay, an electron-probe microanalyzer and an electron diffraction analysis. The luminescent intensities in the amorphous film libraries strongly depended on the chemical composition of each rare-earth (RE) ion. The optimum concentration of rare-earth ions in YEuCOB and YTbCOB were experimentally determined to be Eu = 7.5% and Tb = 20-30%, respectively.     

Influence of deposition pressure on structural, optical and electrical properties of nc-Si:H films deposited by HW-CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) thin films were deposited using HW-CVD technique at various deposition pressures. Characterisation of these films from Raman spectroscopy revealed that nc-Si:H thin films consist of a mixture of two phases, crystalline phase and amorphous phase containing small Si crystals embedded therein. We observed increase in crystallinity in the films with increase in deposition pressure whereas the size of Si nanocrystals was found ∼2 nm over the entire range of deposition pressure studied. The FTIR spectroscopic analysis showed that with increasing deposition pressure the predominant hydrogen bonding in the films shifts from, Si-H to Si-H₂ and (Si-H₂)_n complexes and the hydrogen content in the films was found in the range 6.2-9.3 at% over the entire range of deposition pressure studied. The photo and dark conductivities results also indicate that the films deposited with increasing deposition pressure get structurally modified. It has been found that the optical energy gap range was between 1.72 and 2.1 eV with static refractive index between 2.85 and 3.24. From the present study it has been concluded that the deposition pressure is a key process parameter to induce the crystallinity in the Si:H thin films using HW-CVD.     

Influence of Hf doping concentration on microstructure and optical properties of HfxZn1−xO thin films

Hf_xZn_1−xO thin films (x=3, 7, 10 and 15 mol%) were deposited on Si (1 0 0) using pulsed laser deposition. The influence of the Hf concentration on the microstructure and optical properties of the films was studied. It is found that Hf ions can be effectively doped into ZnO and all films crystallize in the hexagonal wurtzite structure with a preferred c-axis orientation. The lattice constants of Hf_xZn_1−xO films increase with the Hf contents. Two ultraviolet peaks centered at about 364 and 380 nm coexist in the fluorescent spectra. With increasing the Hf contents, the intensity of fluorescent peaks enhances remarkably. At the same time the energy gaps gradually increase, while the positions of ultraviolet peaks remain unchanged. The mechanism of luminescent emission for Hf_xZn_1−xO films was discussed.     

Enhanced luminescence of GdTaO4:Eu thin-film phosphors by K doping

The effect of K⁺ ions on GdTaO₄:Eu³⁺ thin-film phosphors was investigated in order to improve their luminescent properties. The GdTaO₄:Eu_0.1, K_x thin films were synthesized by sol-gel process, and characterized through measuring their microstructure and luminescence. The results indicated that photoluminescence (PL) intensity of GdTaO₄:Eu³⁺ film was improved remarkably by K doping. There were two maxima in the curve of PL intensity against K⁺ dopant concentration, where one was improved up to 2.1 times at x = 0.001 and the other was enhanced up to 2.7 times at x = 0.05. The first maximum was regarded as the alteration of the local environment surrounding the Eu³⁺ activator by incorporation of K⁺ ions, and the second maximum was due to the flux effect. Additionally, the luminescence increased with the increase of firing temperature from 800 °C to 1200 °C.     

Photoluminescence properties of SiNx/Si amorphous multilayer structures grown by plasma-enhanced chemical vapor deposition

Very thin (nanometric) silicon layers were grown in between silicon nitride barriers by SiH₂Cl₂/H₂/NH₃ plasma-enhanced chemical vapor deposition (PECVD). The multilayer structures were deposited onto fused silica and silicon substrates. Deposition conditions were selected to favor Si cluster formation of different sizes in between the barriers of silicon nitride. The samples were thermally treated in an inert atmosphere for 1 h at 500 °C for dehydrogenation. Room-temperature photoluminescence (RT-PL) and optical transmission in different ranges were used to evaluate the optical properties of the structures. UV-VIS absorption spectra present two band edges. These band edges are well fitted by the Tauc model typically used for amorphous materials. RT-PL spectra are characterized by strong broad bands, which have a blue shift as a function of the deposition time of the silicon layer, even for as-grown samples. The broad luminescence could be associated with the confinement effect in the silicon clusters. After annealing of the samples, the PL bands red shift. This is probably due to the thermal decomposition of N-H bonds with further effusion of hydrogen and better nitrogen passivation of the nc-Si/SiN_x interfaces.     

Magnetic behavior of MnAs precipitates in Ga1−xMnxAs diluted magnetic semiconductor

Ferromagnetic Ga_1−xMn_xAs layers (where x≈4.7–5.5%) were grown on (1 0 0) GaAs substrates by molecular beam epitaxy. These p-type (Ga,Mn)As films were revealed to have a ferromagnetic structure and ferromagnetism is observed up to a Curie temperature of 318 K, which is ascribed to the presence of MnAs secondary magnetic phases within the film. It is highly likely that the phase segregation occurs due to the high Mn cell temperature around 890–920 °C, as it is well established that GaMnAs is unstable at such a high temperature. The MnAs precipitate in the samples with x≈4.7–5.5% has a Curie temperature T_c≈318 K, which was characterized from field-cooled and zero-field-cooled magnetization curves.     

Nanocrystal and interface defects related photoluminescence in silicon-rich Al2O3 films

In this study, silicon nanocrystal-rich Al₂O₃ film has been prepared by co-sputtering a silicon and alumina composite target and subsequent annealing in N₂ atmosphere. The microstructure of the film has been characterized by infrared (IR) absorption, Raman spectra and UV-absorption spectra. Typical nanocrystal and interface defects related photoluminescence with the photon energy of 1.54 (IR band) and 1.69 eV (R band) has been observed by PL spectrum analysis. A post-annealing process in oxygen atmosphere has been carried out to clarify the emission mechanism. Despite the red shift of the spectra, enhanced emission of the 1.69 eV band together with the weak emission phenomenon of the 1.54 eV band has been found after the post-annealing. The R band is discussed to originate from silicon nanocrystal interface defects. The IR band is concluded to be a coupling effect between electronic and vibrational emissions.     

Anomalous optical transitions in AlInGaN/GaN heterostructures grown by metalorganic chemical vapor deposition

Using temperature-dependent photoluminescence (PL) measurements, we report a comprehensive study on optical transitions in Al_yIn_xGa_1−x−yN epilayer with target composition, x=0.01 and y=0.07 and varying epilayer thickness of 40, 65 and 100 nm. In these quaternary alloys, we have observed an anomalous PL temperature dependence such as an S-shape band-edge PL peak shift and a W-shape spectral broadening with an increase in temperature. With an increase in excitation power density, the emission peak from the AlInGaN epilayers shows a blue shift at 100 K and a substantial red shift at room temperature. This is attributed to the localization of excitons at the band-tail states at low temperature. Compared to 40 and 65 nm thick epilayers, the initial blue shift observed with low excitation power from 100 nm thick AlInGaN epilayer at room temperature is caused by the existence of deeper localized states due to confinement effects arising from higher In and Al incorporation. The subsequent red shift of the PL peak can be attributed by free motion of delocalized carriers that leads to bandgap renormalization by screening. Due to competing effects of exciton and free carrier recombination processes, such behavior of optical transitions leads to two different values of exponent ‘k’ in the fitting of PL emission intensity as a function of excitation power.     

Structural, electrical, optical and magnetic properties of Co0.2AlxZn0.8−xO films

Co_0.2Al_xZn_0.8−xO films prepared with different molar ratio of aluminum nitrate to zinc acetate were deposited on substrates by the sol-gel technique. X-ray diffraction, photoluminescence and ferromagnetism measurements were used to characterize the Co_0.2Al_xZn_0.8−xO diluted magnetic semiconductors. The authors found that the intensity of the acceptor-related photoluminescence increased with increasing aluminum concentration and an increase in the number of the acceptor-like defects (zinc vacancies especially) in the Co_0.2Al_xZn_0.8−xO film might lead to the enhancement of the magnetic properties. This implies that controls of the aluminum concentration and the number of the acceptor-like defects are important factors to produce strong ferromagnetism Co_0.2Al_xZn_0.8−xO films prepared by the sol-gel method.     

Composition influence of SiNx gate insulator fabricated by radio frequency (RF) Magnetron sputtering on characteristics of organic thin-film transistors

To investigate the effect of composition of SiNx on the properties of organic thin-film transistors (OTFTs), we fabricated bottom gate top contact OTFTs devices with different composition SiNx gate insulator. Pentacene based OTFTs with SiNx insulator, prepared using an interface modification process of UV-ozone treatment, exhibited effective mobility of 0.63 cm2/Vs and on/off current ratio of 10⁵. Overall improvement in field-effect mobility, threshold voltage was observed as silicon content in SiNx increases. The results demonstrate that the viability of using SiNx for OTFTs and of UV-ozone treatment could be used to improve the properties of organic thin-film transistors. The dependence of the contact angle on the SiNx film composition is evident for the untreated samples, the contact angle increases as the silicon content in the untreated nitride film increases. In contrast, the rise in contact angle across all samples after surface treatment signifies effective surface modification to promote hydrophobicity of the nitride surface. The hydrophobic surface is needed for the organic semiconductor.     

Optical properties of high-Al-content crack free AlxGa1−xN (x<0.67) films grown on Si(111) by molecular-beam epitaxy

We report on the optical properties of high-Al-content crack free Al_xGa_1−xN (x<0.67) films grown by molecular-beam epitaxy on Si(111) substrates using ammonia as nitrogen source. The energetic position of the A free exciton as a function of the Al content is determined from photoluminescence and reflectivity measurements at low temperature. A bowing parameter of b=1 eV is deduced from these measurements. The excitonic linewidth increases as a function of Al concentration. The observed variation agrees very well with the one calculated using a model in which the broadening effect is assumed to be due to alloy compositional disordering.     

The dependence of the structural and optical properties on the Te mole fraction in ZnS1−xTex/GaAs heterostructures

Lattice-mismatched ZnS_1−xTe_x epilayers with various Te mole fractions on GaAs (100) substrates were grown by double well temperature gradient vapor deposition. X-ray diffraction patterns showed that the grown ZnS_1−xTe_x layers were epitaxial films. The photoluminescence spectra showed that the peak position of the acceptor-bound exciton (A⁰, X) varied dramatically with changing the Te mole fraction and that the behavior of the (A⁰, X) peak position of the ZnS_1−xTe_x epilayers with a small amount of the Te mole fraction was attributed to a bowing effect. The reflectivity and ellipsometry spectra showed that the absorption energy peak was significantly affected due to the Stoke's effect. These results provide important information on the structural and optical properties of ZnS_1−xTe_x/GaAs heterostructures for improving optoelectronic device efficiencies operating in the spectral range between near ultraviolet and visible regions.