Enhanced photocatalytic activity of Cu-doped ZnO nanorods

Cu-doped ZnO nanorods with different Cu concentrations were synthesized through the vapor transport method. The synthesized nanorods were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and UV–vis spectroscopy. The XRD results revealed that Cu was successfully doped into ZnO lattice. The FE-SEM images showed that the undoped ZnO has needle like morphology whereas Cu-doped ZnO samples have rod like morphology with an average diameter and length of 60–90 nm and 1.5–3 μm respectively. The red shift in band edge absorption peak in UV-vis absorbance spectrum with increasing Cu content also confirm the doping of Cu in ZnO nanorods. The photocatalytic activity of pure and Cu-doped ZnO samples was studied by the photodegradation of resazurin (Rz) dye. Both pure ZnO and the Cu-doped ZnO nanorods effectively removed the Rz in a short time. This photodegradation of Rz followed the pseudo-first-order reaction kinetics. ZnO nanorods with increasing Cu doping exhibit enhanced photocatalytic activity. The pseudo-first-order reaction rate constant for 15 % Cu-doped ZnO is equal to 10.17×10^?2min^?1 about double of that with pure ZnO. The increased photocatalytic activity of Cu-doped ZnO is attributed to intrinsic oxygen vacancies due to high surface to volume ratio in nanorods and extrinsic defect due to Cu doping.     

Structures of nanowires with Zn-ZnO:CuO junctions for detecting ethanol vapors

The synthesis of ZnO-ZnO:CuO structures in the form of overlapping layers of nanowires of pure and copper oxide-doped zinc oxide is described. These structures are tested as ethanol vapor sensors. The following two-stage method is used to form ZnO:CuO nanowires. At the first stage, ZnO nanowires are formed by chemical deposition from a solution. At the second stage, arrays of ZnO nanowires are coated with a copper-containing layer. The CuO content on the surface of ZnO nanowires is changed by varying the number of immersions in a Cu(NO₃)₂ solution. The formed structures are studied by scanning electron microscopy, X-ray diffraction, and energy dispersive X-ray analysis. The interaction of the grown sensor structures with ethanol vapors is analyzed by measuring the potential difference between the layers of pure zinc oxide and copper oxide-modified zinc oxide in the temperature range 190–300°C. The response of the sensor is investigated at various ethanol vapor concentrations and detection temperatures.     

Photocatalysis of novel reduced graphene oxide-CoSe nanocomposites with efficient interface-induced effect

In this work, reduced graphene oxide–CoSe (rGO–CoSe) nanocomposites were synthesized with chemical solution reaction and characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy, Fourier transform infrared spectroscopy, UV–vis spectroscopy, and photodegradation of toxicity malachite green in the water. The effects of rGO/CoSe ratio, initial solution pH, and H₂O₂ concentration on the photodegradation effeciency were studied. The nanocomposites showed excellent sunlight-excited photocatalytic activity to toxicity malachite green in the water. The photodegradation rate increased with increasing rGO/CoSe ratio and initial solution pH. Significantly, remarkable Fenton-like photocatalytic activity enhanced with increasing rGO/CoSe ratio and H₂O₂ concentration was observed. The photodegradation rate constant, k obs, was determined under pseudo-first order conditions. The interface-induced mechanism on enhanced photocatalysis with rGO/CoSe was suggested.     

A twice liquid arc discharge approach for synthesis of visible-light-active nanocrystalline Ag:ZnO photocatalyst

Ag:ZnO hybrid nanostructures were successfully prepared by a twice arc discharge method in liquid. The visible light photocatalytic activities were successfully demonstrated for the degradation of Rhodamine B (Rh. B), Methyl orange (MO), and Methylene blue (MB) as standard organic compounds under the irradiation of 90 W halogen light for 2 h. The Ag:ZnO nanostructures were characterized by X-Ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and ultraviolet-visible absorption spectroscopy (UV-Vis). The results revealed that the Ag:ZnO nanostructures extended the light absorption spectrum toward the visible region and significantly enhanced the Rh. B photodegradation under visible light irradiation. 3 mM Ag:ZnO nanostructures exhibited highest photocatalytic efficiency. It has been confirmed that the Ag:ZnO nanostructures could be excited by visible light (E<3.3 eV). The significant enhancement in the Ag:ZnO nanostructures photocatalytic activity under visible light irradiation can be ascribed to the effect of physisorbed noble metal Ag by acting as electron traps in ZnO band gap. A mechanism for photocatalytic degradation of organic pollutant over Ag:ZnO photocatalyst was proposed based on our observations.     

Synthesis of ZnO nanoparticles using surfactant free in-air and microwave method

Zinc oxide nanoparticles have been successfully prepared by a facile route involving the reaction of zinc sulphate heptahydrate and sodium hydroxide through drop-by-drop mixing synthesis-IA, instant mixing synthesis-IA and under the influence of microwave radiations. The synthesis under different reaction conditions played an important role and led to the formation of zinc oxide nanoparticles of different size and shapes. The synthesized nanoparticles were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. The concentration dependent antimicrobial activity of synthesized ZnO nanoparticles was carried out. The photocatalytic activity was evaluated using the photodegradation of methylene blue (MB) dye under UV irradiation. Further, the optical properties of as-prepared ZnO nanoparticles were investigated by UV-vis spectrophotometry. The absence of surfactant led to a simple, cheap and fast method of synthesis of zinc oxide nanoparticles.     

秧苗状Zn2SnO4纳米线的制备及光致发光性能研究

本文通过化学气相沉积方法成功制备了秧苗状Zn2SnO4纳米线,X射线衍射表明,样品为面心立方结构的Zn2SnO4,同时含有少量的ZnO物相,并且可以通过延长沉积时间的方法获得较为纯净的Zn2SnO4材料.SEM结果显示样品形貌为秧苗状的纳米线.通过样品的光致发光谱的研究发现,Zn2SnO4 的紫外发光强度随着ZnO杂相...     

Different strategies for the synthesis of graphene/ZnO composite and its photocatalytic properties

Owing to its unique physical and chemical properties, graphene has attracted tremendous attention in the preparation of graphene-based composites for various applications. In this study, two different strategies have been developed to load zinc oxide (ZnO) nanorods onto reduced graphene oxide (RGO) sheets, i.e., in situ growth and a self-assembly approach. The microstructure and morphology of the synthesized RGO/ZnO nanocomposites was investigated by X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM) and Brunauer–Emmett–Teller (BET) measurements. Fluorescence emission spectra (PL) of RGO/ZnO composites were performed to attribute quality of combination between RGO and ZnO. Significantly enhanced photocatalytic activity of RGO/ZnO nanocomposites in comparison to bare ZnO nanoparticles was revealed by the degradation of methylene blue under irradiation, which can be attributed to the inhibition of electron–hole pair recombination and enhanced adsorption due to the presence of RGO sheets.     

Synthesis and photocatalysis properties of ZnO structures with different morphologies via hydrothermal method

The special flower-like and sheet-like ZnO structures were successfully synthesized by hydrothermal method. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). The photocatalytic activity of different morphologies of ZnO structures was evaluated by degradating of methyl orange (MO). The photocatalytic degradation process was monitored in terms of decolorization and total organic carbon (TOC) removals. The results indicated that the flower-like ZnO structures were consisted of numerous flower-like aggregates with the size of 2 μm. The sheet-like ZnO nanostructures were obtained by increasing the reaction time. They exhibited higher photodegradation efficiencies under UV light irradiation than flower-like ZnO structures due to the blue shift of the band gap. The photodegradation could be described as the pseudo-first-order kinetics with apparent rate constants ranging from 1.17 × 10⁻² to 3.42 × 10⁻² min⁻¹, which were based on the morphology of the structures. The photodegradation was faster than the mineralization, indicating that the accumulation of by-products were resistant to photocatalytic degradation.     

Influence of S incorporation on the luminescence property of ZnO nanowires by electrochemical deposition

Sulfur-doped zinc oxide (ZnO) nanowires have been successfully synthesized by an electric field-assisted electrochemical deposition in porous anodized aluminum oxide template at room temperature. X-ray diffraction and the selected area electron diffraction results show that the as-synthesized nanowires are single crystalline and have a highly preferential orientation. Transmission electron microscopy observations indicate that the nanowires are uniform with an average diameter of 120 nm and length up to several tens of micrometers. Room-temperature photoluminescence is observed in the doped ZnO nanowires, which exhibits a violet emission and blue emissions besides the typical photoluminescence spectrum of a single crystal ZnO.     

Thermal evaporation synthesis of zinc oxide nanowires

High quality ZnO nanowires were synthesized at high temperature without using heterogenous catalysts. The nanowires had a uniform prismatic shape and were grown in a cacti-like morphology. Characterizations of the products by X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy showed that the ZnO nanowires were single crystalline and of high purity. An intensive exciton emission was observed around 3.25 eV from the ZnO nanowires at room temperature. The growth mechanism was discussed based on the experimental conditions and the ZnO crystal growth habits. This growth method can be used to prepare other metal oxide nanowires. PACS 61.46.+w; 81.16.-c; 81.07.De, 81.05.Hd     

硫掺杂ZnO纳米线的电化学制备及发光特性

"采用电场辅助电化学沉积法,利用阳极氧化铝模板模板制备了高度择优取向的硫掺杂ZnO单晶纳米线．X射线衍射仪、隧道电子显微镜、选取电子衍射对所得样品的结构、形貌分析表明,所得纳米线是沿(101)择优取向的六方纤锌矿结构单晶纳米线,长约几十微米、平均直径约70 nm. X射线光电子能谱对化学组成的分析进一步证实掺杂硫原子的存在．用荧光光谱仪(PL)对S掺杂前后的ZnO纳米线进行光学特性测量发现,S掺杂较大地改变了ZnO纳米线的发光性质．在PL谱中,除了有典型的ZnO纳米线在378、392 nm处的强紫外发光峰     

Solvothermal synthesis,photoluminescence and photocatalytic properties of pencil-like ZnO microrods

Pencil-like ZnO microrods was synthesized via a simple solvothermal process in an aqueous solution of ethylenediamine and ethanolamine. The as-prepared ZnO was characterized by X-ray powder diffraction, field-emission scanning electron microscopy, room temperature photoluminescence spectra and UV–vis absorption spectra. The results indicated that ZnO microrods had the length in the range of 1.3–25 μm. The photocatalytic activity was studied by degradation of methylene blue (MB) aqueous solution, which showed that the as-prepared ZnO microrods possessed a high photocatalytic activity. The formation mechanism of the pencil-like ZnO was also investigated based on the experimental results.     

ZnO–TiO2 nanocomposites formed under submerged DC arc discharge: preparation,characterization and photocatalytic properties

A rutile TiO₂ (α-TiO₂) and hexagonal wurtzite ZnO nanocomposite was directly and synchronously synthesized via arc discharge method submerged in de-ionized water. In correlation with the detailed characterization of the morphology, and crystalline structure of the prepared ZnO–TiO₂ nanocomposites, the UV–visible and photoluminescence properties were studied. X-ray diffraction and transmission electron microscopy investigations revealed the co-existence of α-TiO₂ and hexagonal wurtzite ZnO phases with the ZnO and α-TiO₂ nanoparticles are in nanorod and nanospheres morphologies, respectively. The diameters of the synthesized nanocomposite particles are in the range of 5–70 nm. Interestingly, the as-prepared ZnO–TiO₂ nanocomposite shows better photocatalytic activity for photodegradation of the methylene blue dye than both of pure ZnO and TiO₂ nanocatalyts. This work would explore feasible routes to synthesize efficient metal or/and metal oxide nanocomposites for degrading organic pollutants, gas sensing or other related applications.     

Preparation of highly efficient Al-doped ZnO photocatalyst by combustion synthesis

Novel Al-doped ZnO (AZO) photocatalysts with different Al concentrations (0.5–6.0 mol%) were prepared through a facile combustion method and followed by calcination at 500 °C for 3 h. The obtained nanopowders were characterized by powder X-ray diffraction (XRD), scanning electron microscope (SEM) combined with EDX, transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR), UV–vis spectroscopy and photoluminescence spectroscopy. The XRD patterns of AZO nanopowders were assigned to wurtzite structure of ZnO with the smallest crystallite size about 11 nm consistent with the results from TEM. The doping of Al in ZnO crystal structure successfully suppressed the growth of ZnO nanoparticles confirmed by XRD patterns. The absorption spectra analysis showed that the optical band gap energy (E_g) for the AZO nanopowders were in the range of 3.12–3.21 eV and decreased with increasing of Al dopant. The photocatalytic activities of the samples were evaluated by photocatalytic degradation of methyl orange under visible light (λ ≥ 420 nm) and sunlight irradiation. The results showed that the AZO photocatalyst doped with 4.0 mol% Al exhibited five times enhanced photocatalytic activity compared to pure ZnO. The enhanced photocatalytic activity could be attributed to extended visible light absorption, inhibition of the electron–hole pair's recombination and enhanced adsorptivity of MO dye molecule on the surface of AZO nanopowders.     

Template-free preparation and characterization of nanocrystalline ZnO in aqueous solution of [EMIM][EtSO4] as a low-cost ionic liquid using ultrasonic irradiation and photocatalytic activity

A fast, template-free, and environmentally benign green route for the preparation of nanocrystalline ZnO in aqueous solution of 1-ethyl-3-methylimidazolium ethyl sulfate, [EMIM][EtSO₄], room-temperature ionic liquid (RTIL), via ultrasonic irradiation is proposed. The X-ray diffraction (XRD) studies display that the products are excellently crystallized in the form of wurtzite hexagonal. Energy-dispersive X-ray spectroscopy (EDX) investigations reveal the products are extremely pure. The morphology of as-prepared nanocrystalline ZnO was characterized by scanning electron microscopy (SEM). Diffuse reflectance spectra (DRS) of the products with absorption maxima at 359 nm show blue shift relative to the bulk ZnO with absorption at 384 nm that can be attributed to quantum confinement effect of nanocrystalline ZnO. A possible formation mechanism of the nanocrystalline ZnO using ultrasonic irradiation in aqueous solution of the RTIL is presented. The results demonstrate that photocatalytic activity of the nanocrystalline ZnO prepared in the presence of the RTIL is higher than the prepared sample in water.     

Preparation and photocatalytic activity of Mo-doped WO3 nanowires

Mo-doped WO₃ nanowires were fabricated by a hydrothermal method in the presence of K₂SO₄. The physical properties of prepared nanowires were characterized by X-ray diffraction (XRD), energy-dispersive X-ray analysis (EDS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results show that the obtained products are nanowires with diameters ranging between 10 and 20 nm, and lengths of about 600 nm. Its photoactivity was evaluated through the photodegradation of methylene blue (MB) in aqueous solution. Effects of the molybdenum concentration on the photoactivity of the obtained samples were investigated detailedly. The experimental results indicated that the Mo-doping enhanced the photoactivity of WO₃ nanowires.     

Synthesis and optical properties of ZnO nanorods on indium tin oxide substrate

ZnO nanorods with uniform diameter and length have been synthesized on an indium-tin oxide (ITO) substrate by using a simple thermal evaporation method which is suitable to larger scale production and without any catalyst or additives. The samples were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet-vis (UV-vis) absorption spectrum, photoluminescence (PL) spectrum and Raman spectrum. The single-phase ZnO nanorods grow well-oriented along the c-axis of its wurtzite structure on ITO substrate. The ZnO nanorods shows sharp and strong UV emission located at 380 nm without notable visible light emission in the PL spectrum, which suggests the good crystallinity of the nanorods, which was also testified by their Raman spectrum. The photodegradation of methylene orange (MO) in aqueous solution reveals that the well-arranged c-axis growth of ZnO nanorods possess evidently improved photocatalytic performance and these properties enable the ZnO nanorods potential application in UV laser.     

Photocatalytic performance of ZnO:Fe array films under sunlight irradiation

ZnO:Fe array thin films were prepared by the hydrothermal method using the sol-gel grown film as a seed layer. The samples were characterized by X-ray diffraction (XRD), ultraviolet/visible absorption spectra (UV-vis) and scanning electron microscopy (SEM). The photocatalytic activities of the prepared samples were investigated for the photodegradation of methylene blue (MB) under sunlight irradiation. The results show that the lattice constant a and the cell volume of ZnO:Fe film increase due to the substitution of Fe for Zn. The absorption edge of Fe-doped ZnO displays a red shift with a significant absorption between 600 and 700 nm. The ZnO:Fe array film is composed of disk particles with uniformity and compactness. Doping Fe ions enhances the photodegradation rate of ZnO array film for MB. 1.5% Fe doped ZnO sample exhibits the highest activity under irradiation time of 4 h. Its degradation rate increases about 1.6 times compared to the undoped ZnO.     

锡催化剂助生长法制备孪晶ZnO纳米线及其结构表征

用SnO和Zn的均匀混合物在高温下共烧通过VLS机制制备出孪晶ZnO纳米线的均匀结构。SEM图像显示孪晶ZnO纳米线的直径在100~200nm之间,长度在几十微米到几百微米之间的范围内,有的甚至达到了毫米级,产率也非常的高。TEM图像中ZnO孪晶纳米线顶端的金属Sn颗粒表明了孪晶结构的Sn催化生长。高分辨电子图谱显示了氧化锌纳米线孪晶结构的特征。电子衍射分析发现孪晶氧化锌的晶带轴的方向是[0110],孪晶面为(1013),并且通过明场像和暗场像分析了孪晶纳米线的晶格关系,确定了孪晶纳米线的汽-液-固(VLS)生长机制。     

ZnO/Cu_2O异质结纳米阵列制备及光催化性能

利用湿化学法在FTO玻璃基底上制备了高度规整的ZnO纳米棒阵列(ZnO NRAs),以此为衬底,采用磁控溅射法在ZnO NRAs表面沉积Cu_2O薄膜。分别用X射线衍射仪、X射线光电子能谱、扫描电镜、光致光谱、紫外可见分光光度计和电化学工作站对样品的物相、形貌、吸收光谱、光电性能进行了表征,用甲基橙(MO)模拟有机物废水研究复合材料的光催化性能。结果表明:ZnO纳米棒为六方纤锌矿结构,其直径约为80~100 nm,长约2~3μm,棒间距约100~120 nm。立方晶系的Cu_2O颗粒直径约为100~300 nm,形成致密膜层并紧密覆盖在ZnO NRAs表面上,构成ZnO/Cu_2O异质结纳米阵列(ZnO/Cu_2O HNRAs)结构。与纯ZnO NRAs和Cu_2O相比,ZnO/Cu_2O HNRAs在可见光范围内的吸收显著增强,吸收波长向可见光方向偏移。ZnO/Cu_2O HNRAs的载流子传递界面的电荷转移速度快,有效促进了光生电子和空穴的分离。在紫外-可见光照射65 min后,ZnO/Cu_2O HNRAs的降解效率为94%,分别是纯ZnO NRAs和Cu_2O的18倍和1.7倍。