AC losses and transverse resistivity in filamentary MgB2 tape with Ti barriers

We measured and analyzed AC losses of MgB₂ tape with 19 filaments surrounded by Ti barriers and embedded in copper stabilization, exposed to external magnetic field with frequencies from 30 mHz up to 1.4 Hz and amplitudes up to 0.8 T at 4.2 K. Using the measured frequency dependence of the total AC losses we determined the contribution of hysteresis and coupling losses. The transverse resistivity determined from the coupling losses is considerably higher than that corresponding to the resistivity of copper stabilization before the tape processing due to diffusion of Ti. From the measured penetration field critical current densities were determined using results of theories for circular as well as rectangular filaments.     

Formation of the (Bi, Pb)2Sr2Ca2Cu3O10+δphase: reaction mechanism and kinetics

In order to elucidate the formation mechanism of the Bi, Pb(2223) phase, extensive investigations have been performed by means of combined differential thermal analysis and thermo-gravimetric measurements, X-ray diffraction as well as scanning electron microscopy and energy dispersive X-ray microanalysis.Starting from co-precipitated oxalate powders, the transformations leading to the formation of the Bi, Pb(2223) phase were studied. Based on these investigations the Bi,  Pb(2223) phase formation process, involving the Bi, Pb(2212), Ca₂PbO₄and alkaline-earth cuprate phases as precursors has been separated into elemental steps. A new model for the formation mechanism of the Bi, Pb(2223) phase will be presented.The Bi, Pb(2223) phase formation kinetics has been studied using the Avrami relation for isothermal phase transformations. The analysis of the Bi, Pb(2223) phase evolution revealed a marked change of the Avrami exponent during the course of the Bi, Pb(2223) phase formation after about 12 hours sintering at 857 ° C.The activation energy for the formation of the Bi, Pb(2223) phase has been determined under various experimental conditions. The nominal composition of the precursor powders, the temperature at which they were calcined as well as the size of their constituents were found to have a significant influence on the value of the activation energy.     

Effect of fluorine doping on phase formation and properties of Bi(Pb)-2223 ceramics

Superconducting ceramics of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_yF_x (x = 0–0.6) are prepared in air by conventional solid state reaction and characterized. The study shows that the melting point of the samples decreases as fluorine content increases. As a consequence, the grain size increases with the doping level and for x = 0.6, the sample is completely deformed and presents a concave shape making impossible the measurements on it. The Vickers microhardness reaches its maximum for x = 0.2. The analysis of the X-ray diffraction results reveals that all the samples are composed of only Bi(Pb)-2212 and Bi(Pb)-2223 phases. The highest proportion of the high T_c phase (Bi(Pb)-2223) is also observed for x = 0.2 and is about 67.32%. The refinement of cell parameters is done by considering the structural modulation. The results show that the doping leads to a reduction of cell volume as well as the a axis component of modulation. From resistivity versus temperature measurements, it is shown that the doped phases exhibit higher onset critical transition temperatures than the undoped one. The residual resistivity increases with fluorine content suggesting that the doping introduces structural defects and disorder into the samples. The obtained critical current density at 77 K under zero magnetic field also increases with fluorine doping.     

Magnetoresistance hysteresis of bulk textured Bi1.8Pb0.3Sr1.9Ca2Cu3Ox + Ag ceramics and its anisotropy

Magnetoresistance of bulk textured Bi_1.8Pb_0.3Sr_1.9Ca₂Cu₃O_x + Ag ceramics has been studied in the magnetic fields applied parallel and perpendicular to a–b planes of Bi2223 crystallites. Besides well known anisotropy of magnetoresistance of textured superconductors (R_H || c > R_H || a–b), anisotropic hysteresis of R(H) dependences was investigated. Parameters characterizing hysteretic R(H) curves differ for the cases H || c and H || a–b. This behavior is explained within the model of a granular superconductor where the total magnetic induction in the intercrystallite boundaries is superposition of the external field and the magnetic field induced by dipole magnetic moments of neighbor crystallites.     

On some consequences of an external magnetic field applied to HTS coils

A computational model which enables to evaluate the distribution of the critical currents, electric fields and the voltage in the winding of a solenoidal high temperature superconducting (HTS) magnets subjected to an external magnetic field parallel with the magnet axis, was developed. The model comes out from the well-known power law between the electric field and the transport current of the HTS tape short sample. It allows to predict the voltage–current V(I) characteristics of both the pancake coils and the complete magnet. The model was applied to the magnet system consisting of 22 pancake coils made of multifilamentary Bi(2223)/Ag tape at 20 K, which is subjected to an external uniform magnetic field parallel with the coil axis. A rather unexpected behavior of the magnet at different operating conditions (operating current and external magnetic field strength) is predicted, analyzed and reported together with a theoretical explanation. On one hand, the external uniform magnetic field parallel with the coil axis increases the resulting magnetic field strength, however, on the other hand it simultaneously decreases the angle between the resulting magnetic field and the tape surface. Thus, the effect of higher magnetic loading caused by the presence of an external magnetic field strength which is acting on individual turns located close to the coil’s flanges is compensated by more favorable orientation of the tape with respect to the resulting magnetic field. As a result, increase in the critical currents of these turns is expected. Further, the results indicate, that in case of the high field HTS insert coils the anisotropy in the I_c(B) characteristic does not play a substantial role. As a consequence, the technology of the production of the tapes for high field insert HTS coils should concentrate rather on the tapes having the current carrying capacity as high as possible, than on the attempt how to decrease the anisotropy in the I_c(B) by changing the architecture of the filaments in the tape.     

Growth,structure and physical properties of single crystals of pure and Pb-doped Bi-based high Tc superconductors

Single crystals of (Bi_1−xPb_x)₂Sr₂Ca₂Cu₃O_10+δ (x = 0 and 0.16) (sizes up to 3 × 2 × 0.1 mm³) have been grown by means of a newly developed “vapour-assisted travelling solvent floating zone” technique (VA-TSFZ). Post-annealing under high pressure of O₂ (up to 10 MPa at T = 500 °C) was applied to enhance T_c (up to 111 K) and improve the homogeneity of the crystals (ΔT_c ⩽ 1 K). The structure of both Pb-free and Pb-doped Bi-2223 was refined for the first time from single crystal X-ray diffraction (XRD) data. The unit cell of the average structure is pseudo-tetragonal with a = 5.4210(7), b = 5.4133(6) and c = 37.010(7) Å, and a = 5.395(1), b = 5.413(1) and c = 37.042(11) Å, for the Pb-free and the Pb-doped phase, respectively. An incommensurate modulation in the direction of one of the short cell vectors has been defined (q ∼ 0.21 a¹), however, the structure can be conveniently described in a supercell with a fivefold volume (a = 27.105(4) Å). With respect to the “non-modulated” structure, one additional oxygen atom for ten initial O was found to be inserted into the BiO layers. The superconducting anisotropy of Bi-2223 was found to be ∼50, from measurements of the lower critical field. The anisotropy of Bi-2223 is significantly reduced compared to that of Bi-2212, and this accounts for the enhanced irreversibility fields in Bi-2223. Furthermore, Bi-2223 has a higher critical current density, and a reduced magnetic relaxation rate compared to Bi-2212, which are both signatures of more effective pinning in Bi-2223 due to its reduced anisotropy.     

Intrinsic tunneling spectroscopy for Bi2−xPbxSr2CaCu2O8+δ of nm-thickness mesa structure

We have investigated intrinsic tunneling spectroscopy (ITS) with short-pulse bias to mesa structures consisting of several layers of intrinsic Josephson junction superlattices of Bi_1.8Pb_0.2Sr₂CaCu₂O_8+δ(PbBi2212). Through ITS, the superconducting gap 2Δ = 75 meV (at 10 K) is obtained for a PbBi2212 crystal. The large 2Δ value corresponds to the underdoped property of Pb-free Bi2212, which is consistent with the ab-plane transport measurement results performed simultaneously. The normal tunneling resistance R_N derived from the high bias region of the I–V characteristics is significantly small in comparison with underdoped Bi2212. Moreover, J_c of PbBi2212 is less deviated from the Ambegaokar–Baratoff value than the case of underdoped Bi2212. It is interpreted that the Pb substitution makes the tunnel barrier lower, resulting in a reduced anisotropy and a high J_c even with a lower doping.     

Energy storage properties of antiferroelectric 0.92NaNbO3-0.08SrZrO3 film on (001)SrTiO3 substrate

The present study demonstrates the fabrication of an antiferroelectric 0.92NaNbO₃-0.08SrZrO₃ film deposited on a SrRuO₃ coated (001)SrTiO₃ single crystal substrate by pulsed laser deposition. In the 0.92NaNbO₃-0.08SrZrO₃ film, the domain with its c-axis aligned with the out-of-plane direction contributed to the stabilization of an antiferroelectric phase under the high electric field. The film had an energy storage density of 2.9 J cm⁻³ and storage efficiency of 67% at room temperature, which kept at 2.5 J cm⁻³ and 50% at high temperature of 150 °C.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.     

Low-field AC susceptibility study of critical current density in Eu:123 and Bi:2223 superconductors

Low-field AC susceptibility measurements have been made, at different values of AC field amplitude H_m (26–600 A/m), on Eu:123 and Bi:2223 samples. Analysis of the temperature dependence of the AC susceptibility has been done employing Beans’ critical state model. The intergranular critical current density (J_c) is calculated as a function of both H_m and temperature for both samples, respectively. It is found that J_c increases with increasing H_m for both samples and its values are generally higher in Bi sample than in Eu sample. Our results are discussed in terms of zero-temperature pinning potential βI(0) in both systems.     

Inelastic neutron scattering on iron-based superconductor BaFe2(As,P)2

Inelastic neutron scattering has been performed on powder sample of an iron-based superconductor BaFe₂(As_0.65P_0.35)₂ with superconducting transition temperature (T_c) = 30 K, whose superconducting (SC) order parameter is expected to have line node. In the normal state, constant-E scan of dynamical structure factor, S(Q, E), exhibits a peak structure centered at momentum transfer Q ～ 1.20 Å^?1, corresponding to antiferromagnetic wave vector. Below T_c, the redistribution of the magnetic spectral weight takes place, resulting in the formation of a peak at E ～ 12 meV and a gap below 6 meV. The enhanced magnetic peak structure is ascribed to the spin resonance mode, evidencing sign change in the SC order parameter similar to other iron-based high-T_c superconductors. It suggests that fully-gapped s_± symmetry dominates in this superconductor, which gives rise to high-T_c (=30 K) despite the nodal symmetry.     

Andreev reflection between a normal metal and the FFLO superconductor II: A self-consistent approach

We consider Andreev reflection in a two dimensional junction between a normal metal and a heavy fermion superconductor in the Fulde–Ferrell (FF) type of the Fulde–Ferrell–Larkin–Ovchinnikov (FFLO) state. We assume s-wave symmetry of the superconducting gap. The parameters of the superconductor: the gap magnitude, the chemical potential, and the Cooper pair center-of-mass-momentum Q, are all determined self-consistently within a mean-field (BCS) scheme. The Cooper pair momentum Q is chosen as perpendicular to the junction interface. We calculate the junction conductance for a series of barrier strengths. In the case of incoming electron with spin σ = ↑ only for magnetic fields close to the upper critical field H_c2, we obtain the so-called Andreev window, i.e. the energy interval in which the reflection probability is maximal, which in turn is indicated by a peak in the conductance. The last result differs with other non-self-consistent calculations existing in the literature.     

Electromechanical properties of 2-2 cement based piezoelectric composite

A 2-2 type cement based piezoelectric composites were fabricated by dice-and-fill technique. The influences of lead magnesium niobate-lead zirconate-lead titanate (PMN) ceramic volume fraction on the electromechanical properties of the composite were investigated. The results indicate that the planar electromechanical coupling factor K_p of the composite is hardly influenced by the PMN volume fraction, which fluctuates between 35% and 37%, while both the thickness electromechanical coupling factor K_t and the mechanical quality factor Q_m exhibit the trend of increase. When PMN volume fraction is 69.2%, K_t could reach to 49.8%, which is larger than that of the PMN ceramic (K_t = 46%).When PMN volume fraction is 41.7%, Q_m is 4.5, which is also much less than that of the PMN ceramic (Q_m = 70). This means that the composite has wider frequency band and higher sensitivity to be used as transducers. With the increase of PMN volume fraction, the acoustic impedance of the composite also exhibits the trend of increase.     

Modified Lanthanum Zirconium Oxide buffer layers for low-cost,high performance YBCO coated conductors

The pyrochlore Lanthanum Zirconium Oxide, La₂Zr₂O₇ (LZO), has been developed as a potential replacement barrier layer in the standard RABiTS three-layer architecture of physical vapor deposited CeO₂ cap/YSZ barrier/Y₂O₃ seed on Ni–5%W metal tape. The main focus of this research is to ascertain whether: (i) we can further improve the barrier properties of LZO; (ii) we can modify the LZO cation ratio and still achieve a high level of performance; and (iii) it is possible to reduce the number of buffer layers. We report a systematic investigation of the LZO film growth with varying compositions of La:Zr ratio in the La₂O₃–ZrO₂ system. Using a metal–organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of La_xZr_1?xO_y (x = 0.2–0.6) on standard Y₂O₃ buffered Ni–5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial LZO phase with only (0 0 1) texture can be achieved in a broad compositional range of x = 0.2–0.6 in La_xZr_1?xO_y. Both CeO₂ cap layers and MOD–YBCO films were grown epitaxially on these modified LZO barriers. High critical currents per unit width, I_c of 274–292 A/cm at 77 K and self-field were achieved for MOD–YBCO films grown on La_xZr_1?xO_y (x = 0.4–0.6) films. These results indicate that LZO films can be grown with a broad compositional range and still support high performance YBCO coated conductors. In addition, epitaxial MOD La_xZr_1?xO_y (x = 0.25) films were grown directly on biaxially textured Ni–3W substrates. About 3 μm thick YBCO films grown on a single MOD–LZO buffered Ni–3W substrates using pulsed laser deposition show a critical current density, J_c, of 0.55 MA/cm² (I_c of 169 A/cm) at 77 K and 0.01 T. This work holds promise for a route for producing simplified buffer architecture for RABiTS based YBCO coated conductors.     

Microfabrication of solenoid-type RF SMD chip inductors with an Al2O3 core

We investigated micron size, high-performance, and solenoid-type radio-frequency surface-mounted device (SMD) chip inductors with a low-loss Al₂O₃ core for a GHz drive microwave circuit application. Copper coils with a diameter of 27 μm were used and the chip inductors fabricated in this study are 0.86 × 0.46 × 0.45 mm³. The high-frequency characteristics of the inductance (L), quality factor (Q), and impedance (Z) of the developed inductors were measured using a RF impedance/material analyzer (HP4291B with HP16193A test fixture). The developed inductors have a self-resonant frequency of 3.7–5.2 GHz and exhibit L of 15–34 nH. The inductors have Q of 38–49 over the frequency ranges of 900 MHz–1.7 GHz. The calculated data obtained from the equivalent circuit and the derived equation of Q described the high-frequency data of L, Q, and Z of the inductors developed quite well.     

The effect of sintering temperature on the intergranular properties of Bi2223 superconductors

A systematic study of the intergranular properties of (Bi,Pb)₂Sr₂Ca₂Cu₃O_y (Bi2223) polycrystalline samples has been done using the electrical resistivity and Ac susceptibility techniques. In this project, we have prepared a series of Bi2223 samples with different sintering temperature. The XRD results show that by increasing sintering temperature up to 865 °C the Bi2212 phase fraction decrease. It was found that the Bi2212 phase on the grain boundaries is likely to play the role of weak links and consequently reduces the intergranular critical current densities. Analysis of the temperature dependence of the Ac susceptibility near the transition temperature (T_c) has been done employing Bean's Critical State Model. The observed variation of intergranular critical current densities (J_c) with temperature indicates that the weak links are changed from superconductor–normal metal–superconductor (SNS) for well-coupled sample to superconductor–insulator–superconductor (SIS) type of junctions for the sample with high Bi2212 phase fraction.     

Large transport critical currents of powder-in-tube Sr0.6K0.4Fe2As2/Ag superconducting wires and tapes

We report the achievement of transport critical currents in Sr_0.6K_0.4Fe₂As₂ wires and tapes with a T_c = 34 K. The wires and tapes were fabricated through an in situ powder-in-tube process. Silver was used as a chemical addition as well as a sheath material. All the wire and tape samples have shown the ability to transport superconducting current. Critical current density J_c was enhanced upon silver addition, and at 4.2 K, a largest J_c of ～1200 A/cm² (I_c = 9 A) was achieved for 20% silver added tapes, which is the highest in iron-based wires and tapes so far. The J_c is almost field independent between 1 T and 10 T, exhibiting a strong vortex pinning. Such a high transport critical current density is attributed to the weak reaction between the silver sheath and the superconducting core, as well as an improved connectivity between grains. We also identify a weak-link behavior from the apparent drop of J_c at low fields and a hysteretic phenomenon. Finally, we found that compared to Fe, Ta and Nb tubes, Ag was the best sheath material for the fabrication of high-performance 122 type pnictide wires and tapes.     

Reel-to-reel fabrication of meter-long YBCO coated conductor

YBa₂Cu₃O_7?δ (YBCO) superconductors were coated on the CeO₂/YSZ/Y₂O₃ buffered Ni-5at%W tapes by a reel-to-reel pulsed laser deposition (PLD). The process of a multi-layer deposition of YBCO film was explored. X-ray diffraction texture measurements showed good both in-plane and out of plane crystalline orientations in YBCO films. The average values calculated at a full width at half maximum (FWHM) of the peaks from phi-scans (φ) and omega (ω) scans for one meter-long YBCO tape were 7.49° and 4.71°, respectively. The critical current (I_c) was over 200 A/cm-width at 77 K and under self-field for meter-long YBCO tape. The critical transition temperature of the YBCO tape was typically as 90.1 K with 0.5 K transition widths.     

Magnetic and magneto-optical properties of MnSb films on various substrates

Magnetic and magneto-optical properties of MnSb films with different crystalline orientations on various semiconductors of GaAs(1 0 0), GaAs(1 1 1)A, B, and sapphire(0 0 0 1) have been measured by a vibrating sample magnetometer (VSM) and a home-made magneto-optical Kerr effect (MOKE) system. All these samples have their easy axes in the plane and show ferromagnetic properties. Among these samples, the film on GaAs(1 1 1)B has the lowest coercive force H_c and the largest squareness (SQ) value, whereas the film on GaAs(1 0 0) shows the largest H_c and the lowest SQ value. A large Kerr rotation angle of about 0.3° was observed at a wavelength of λ=632.8 nm for the film on sapphire in the field applied both parallel and perpendicular to the film plane. However, the MnSn films on other substrates do not have an observable Kerr rotation. The dynamic effect of the hysteresis was also measured using our MOKE system. As the frequency of applied magnetic field increases, the loop rounds off at the corners and the loop area increases.     

Symmetrical transition of an atomic arrangement for 2D Bi films on Rh(111)

The atomic arrangement of submonolayer Bi films on Rh(111) surface was examined using low-energy electron diffraction (LEED) and scanning tunneling microscopy (STM). With low coverage, the LEED patterns showed incommensurate (IC) spots. The unit cell of IC was close to c(2 × 4) and had twofold symmetry. As the coverage increased, the unit cell shrank continuously along the [$\overline{1}10$] direction, and the commensurate c(2 × 4) was formed at a coverage of 0.5 ML. At the coverage above 0.5 ML, two different structures of c(2 × 4) and (4 × 4) were observed by STM. When the surface is fully saturated by monolayer Bi atoms, Bi atoms formed the uniform (4 × 4) structure with sixfold symmetry. This is due to a strong Bi–Rh attractive interaction resulting in the two-dimensional localization of Bi adsorbates on the surface. As a result, a symmetrical transition of Bi films from twofold to sixfold symmetry occurred on Rh(111).